Hercules HE41 Owner's Manual & Safety Instructions

Item 56214 PARTS LIST AND DIAGRAM Parts List Part Description Qty 1 Release Lever 1 2 Cam 1 3 Screw 3 4 Cylindrical Pin 1 5 Spanner Base 1 6 Hot Board 1 7 Spindle 1 8 Connector 1 9 Compression Spring 1 10 Washer 1 11 Orientation Sleeve 1 12 Compression Spring 2 13 Clutch Lining 1 14 Shaft 1 15 O Ring 1 18 Left/Right Cover 1 19 Screw 3 20 Retaining Ring 1 21 Ball Bearing 619 1 22 Screw 4 23 Fore Housing 1 24 Light Socket 1 25 Light Cover 1 26 Shaft Cover 1 27 Ball Bearing 618 1 30 Spring Board 1 32 Power Supply Board 1 33 Pendulum Fork ...

Item 56214 b. When using a handheld power tool, maintain a firm grip on the tool with both hands to resist starting torque. 11. Do not leave the tool unattended when it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving. 12. This product is not a toy. Keep it out of reach of children. 13. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. ...

Item 56214 MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the Switch is locked and unplug the tool from its electrical outlet is removed before performing any procedure in this section. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. ...

Item 56214 IMPORTANT SAFETY INFORMATION GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool. Work Area Safety 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as ...

Item 56214 TAbLE A: RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120/240 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25´ 50´ 75´ 100´ 150´ 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - * based on limiting the line voltage drop to five volts at 150% of the rated amperes. Symbology Double Insulated V Volts ~ Alternating Current A Amperes n0 xxxx/min. No Load Revolution ...

Item 56214 GROUNDING TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounded Tools: Tools with ...

Item 56214 PARTS LIST AND DIAGRAM Parts List Part Description Qty 1 Release Lever 1 2 Cam 1 3 Screw 3 4 Cylindrical Pin 1 5 Spanner Base 1 6 Hot Board 1 7 Spindle 1 8 Connector 1 9 Compression Spring 1 10 Washer 1 11 Orientation Sleeve 1 12 Compression Spring 2 13 Clutch Lining 1 14 Shaft 1 15 O Ring 1 18 Left/Right Cover 1 19 Screw 3 20 Retaining Ring 1 21 Ball Bearing 619 1 22 Screw 4 23 Fore Housing 1 24 Light Socket 1 25 Light Cover 1 26 Shaft Cover 1 27 Ball Bearing 618 1 30 Spring Board 1 32 Power Supply Board 1 33 Pendulum Fork ...