HUANUO HNDS8 Instruction Manual

Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at [email protected]. CAUTION: Avoid potential personal injuries and property damage! • Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use. • This product contains a high pressure gas spring, fire and percussion prohibited. Also it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand over to professional agencies if the product is abandoned. • The desk must be capable of supporting three times the weight of the total load (the mount, the monitor and all accessories weight). Don't use the product on particle board. IMPORTANT SAFETY INFORMATION If this desk mount is NOT compatible, please contact customer service at [email protected] to find a compatible product. If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than VESA 75x75mm/3x3in., this mount is NOT compatible. 01 Weight Restrictions 4.4-19.8 lbs. (2-9 kg) DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury. WARNING If your monitor weighs more, this mount is NOT compatible. Your monitor (including accessories) CANNOT EXCEED 4.4-19.8lbs (2-9 kg) MAX:100 mm/4 in. MAX:100 mm/4 in. MAX:100 mm/4 in. 100 mm ≈ 4 in. 75 mm ≈ 3 in. Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)

1. Ensure monitor has been attached to the mount. 2. Read your monitor box or manual to find out monitor net weight. 3. Ensure the net weight of monitor (including accessories) is between 4.4~19.8 Ibs (2-9 kg). Clockwise to reduce tension(carry less weight) Counter-clockwise to increase tension(carry more weight) TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION Adjustment Sign

Supplied Parts and Hardware Warning:This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our customer service at [email protected]. • Please note: Not all hardware included in this package will be used. 5/32 in.(4mm) Allen Key (F) (D) M8 Butterfly Nut (D) M8x120mm Grommet Bolt (E) Locking Plate 03 Pole Assembly X1 02 C-Clamp X1 Tools Needed (Not lncluded) Screwdriver M6x12mm (3pcs) Bolt(C)

M4x6mm (4pcs) Bolt (G) 01 Arm X2 05 Cable Clip X2 Supplied Parts and Hardware for Step 2 Supplied Parts and Hardware for Step 3 Supplied Hardware for Step 4 and Step 6 Supplied Parts and Hardware for Step 8 Bolt (A) M4x12mm (8pcs) Bolt (B-1) M4x16mm (8pcs) Spacer (B-2) 5mm (8pcs)

4 Step 1 Install the Base A. For Clamp Mounting A-1 Install the C-Clamp 3 Connect part [Y] to part [X] according to the thickness of the desktop OR The first choice X Y The second choice X Y 1 2 Warning: Ensure bolts are secured firmly. 5/32 in. (4mm) 03 X F Connect part [X] to pole assembly [03] Detach the c-clamp entirely X Y ① ②

1 Install the grommet bolt Warning: Ensure bolts are secured firmly. D Warning: Ensure bolts are secured firmly. Secure the base to desktop using locking plate [E] and butterfly nut [D] 2 E D φ0.4-φ2 in. (φ10-φ50mm)

Ensure bolts are secured firmly. 05 03 Slide arm [01] to the pole assembly [03] 2 1 Slide the cable clip [05] to the pole assembly [03] Secure the arm [01] to the pole assembly [03] by tightening the preassemble bolts on the arms [01] 3 01 03 5/32 in. (4mm)

Be sure to keep the arm in horizontal position during adjustment. Or else, it will be difficult to adjust the mount or possibly damage the mount. 1. If the monitor can stay at the desired height by itself, no adjustment needed. 2. If the monitor rises up, press the arm to keep it in horizontal position and then use the 13/64 in.(5mm) Alley key (F) to turn the bolts clockwise(“-” direction) to reduce tension of the arm only until the monitor can stay at the desired height by itself. 3. If the monitor falls down, lift the arm to keep it in horizontal position and then use the 13/64 in.(5mm) Alley key (F) to turn the bolts counter-clock-wise(“+” direction) to increase tension of the arm only until the monitor can stay at the desired height by itself. Step 3 Attach Monitors to the Arms 3-1 Choose Proper bolts 3-2 Install Monitors to the Arms 1 0.1-0.2in.(3-5mm) spacing left The tension is preset at 8.8~11 Ibs(4-5kg). After hanging the monitor to the mount,please release the monitor slowly to prevent it from falling suddenly. 100x100mm 75x75mm A Screwdriver [Not Included] Flat back monitor Round back monitor 100x100mm 75x75mm B-1 B-2

Non-proper usage directions Proper usage directions (1 rotation ≈ 1 lb) 13/64 in. (5mm)

Step 7 Rotation Adjustment “+” Clockwise: Tighten “-” Counter-clockwise: Loosen Situation 1: If the monitor can stay at the desired tilt angle by itself, no adjustment needed. Situation 2: If the monitor can not stay at the desired tilt angle by itself, turn the bolts clockwise or counter-clockwise as shown until the monitor can stay at the desired tilt angle by itself. Rotation Only suitable for the monitors with the center of gravity in the center position 13/64 in. (5mm)

04 Screwdriver [Not Included] Secure the Cable Cover [04] to the arm [01] by tightening the bolts [G] using screwdriver Loosen the preassembled bolts [S] on the arm [01] to detach the cable guide from the arm [01], and keep the bolt for the use in next step Route the cables into the cable guide and secure the cable guide by tightening the bolts [S] using screwdriver S