HUANUO HNCM2 Installation Instruction

surface to avoid damage. Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. Carefully read all instructions before attempting installation. IMPORTANT SAFETY INFORMATION Install and operate this device with care. Please read this instruction before installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation. Please call a qualified installation contractor for help if you don't understand these directions or have any doubts about the safety of the installation. Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product. ! ! ! ! !

Not Included Phillips Screwdriver Swivel Arms d (x2) Pole a (x1) “C” Clamp b (x1) “C” Clamp Brace c (x1) Nut h (x2) VESA Plate e (x2) M5x14 Bolt f (x3) M8x12 Bolt g (x2) Spring Washer l (x1) M10 Bolt i (x1) Support Plate j (x1) M10 Washer k (x1) Allen Key o (x1) Grommet Base Plate m (x1) Wire Clip n1 (x1) Wire Clip n2 (x4) M4 Spacer s (x8) Wrench p (x1) M4x12 Thumb Bolt q (x8) M4x30 Bolt r (x8) Laptop Tray t (x1) M4x10 Bolt u (x4) M4 Nut v (x4)

Option B: Grommet Base Assembly a Figure 3 m f Figure 4 j i p k l Option A：Desk Clamp Assembly a Figure 1 f c Figure 2 g o b Plastic Knob 1.Use 3 pieces M5x14 bolts(f) to install the C Clamp brace(c) to the Pole. Use the Allen Key(o) to tighten the bolts. See Figure 1. 2.According to the thickness of the desktop, Use 2 pieces M8x12 bolts(g) to install the C clamp(b) to C clamp brace (c). Use Allen Key(o) to tighten the bolts and then tighten the C clamp to the desktop by adjusting the plastic knob. See Figure 2. Existing Grommet Hole Installation If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount 1.Use 3 pieces M5x14 bolts(f) to install Grommet Base Plate(m) to the Pole(a). Use the Allen Key to tighten the bolts. See Figure 3. 2.Position the Pole(a) on the mounting surface and under the desktop comes the Support Plate (j), M10 Washer(k), Spring Washer (l). Use the provided Wrench(p) to fasten the M10 Bolt. See Figure 4. o o

Step 2 Install Arm to the Pole Option B: Grommet Base Assembly a Figure 5 Figure 6 m f Existing Grommet Hole Installation 1. Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8" (10mm) diameter hole at the marked position through the mounting surface. 2.Use 3 pieces M5x14 Bolts(f) to install the Grommet Base Plate(m) to the Pole(a). Use the Allen Key(o) to tighten the bolts. See Figure 5. 3.Position the Pole(a) on the mounting surface and under the desktop comes the Support Plate (j), M10 Washer(k), Spring Washer (l). Use the provided Wrench(p) to fasten the M10 Bolt. See Figure 6. Install Swivel Arms(d) to the Pole(a). Fasten the bolt with supplied Allen Key(o). Attach the Wire Clip(n1,n2) to the Pole(a) and Swivel Arms(d). d o n1 n2 d o

Step 4 Slide the Monitor onto the Head of Swivel Arm h s r t u v q For Laptop For Monitor with Flat Back For Monitor with Curved or Recessed Back Slide the monitor onto the head of Swivel Arm(d) as shown in the above diagram. Install the security Nut(h). Make sure the security nut is installed before you rotate the monitor.

Step 6 Manage the Wires and Store the Allen Keys on Wire Clip o o Fix the tilt angle Tighten the bolt with the supplied Allen Key(o) to fix the tilt angle. Use the supplied Allen Key(o) to make the necessary adjustments.

services for our customers. Would you kindly share your experience on Amazon if you are satisfied? Should you have any issues, please don't hesitate to contact us. Telephone：800-556-0533 Mon-Fri 10am - 6pm (PST) (USA) Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)