Grandview GPCM-E3540 Instruction Manual

with high precision adjustment Applicable Model GPCM-E3540 GPCM-E4560 Please read before using Thank you for purchasing our products. Please read the instruction manual carefully in order to ensure this projector lift is suitable for your projection equipment. Cautious Warnings For safety, the minimum of ceiling must be 20KG weight Caution Please do not incline the projector extremely. Please do not take apart the accessories of projector ceiling mount. Do not take apart Height Adjustment Take apart the ornament cap of main bar (2-3) and loosen the front positioning screws. Adjust the subsidiary bar (2-3) to reqiured position, and then install the ornament cap of main bar (2-3) as figure 9. figure 9 vertical tilt:±15° The angle of The nagle of horizontal tilt:±8° Rotation:360° Angle Adjustment 1.Vertical adjustment: rotate the adjusting button (3-3) for vertical angle, figure 10 2.Horizontal adjustment: rotate the adjusting button (3-2) for horizontal angle, figure 11 3.Horizontal rotation adjustment: loosen the rotation adjusting screw (3-4), the installation base can be rotated by 360°;fasten the rotation adjusting screw (3-4) after deciding the angle,figure 12 figure 10 figure 11 figure 12 Installation of main bar 1.Firstly, please confirm how many installation holes the projector has? 3 or 4 2.If there are 3 holes, the installation arms (4-2) need to be taken apart from Installation bracket firstly. Connect 3 installation arms(4-2) to the projector, and then connect the installation arms (4-2) to the installation base (4-5) However,the installation base needs to be the center of projector. Figure 13. 3.Connect the installation arms to the projector conversely if the distance of installation holes is less than 120mm. Connect the installation arms (4-2) to the installation base (4-5) via sliding installation button (4-4) as figure 14 4.Rotate the adjustable screw (4-3) for adjusting the height of instllation arms (4-2) if the installation holes are not at the same level as figure 15 5.The front or back of adjuster must be parallel to the surface of projector as figure 16 The front or back of adjuster must be parallel to the surface of projector figure 13 figure 14 figure 15 figure 16 Scope of adjustment: 10mm Details of installation Grandview Crystal Screen Canada Ltd. #11- 3751 North Fraser Way, Marine Way Business Centre, Burnaby, BC, Canada V5J 5G4 Tel: 1-604-412-9777 Fax: 1-604-412-9796 Website: www.grandviewscreen.ca Guangzhou Grandview Crystal Screen Co., Ltd. No.43,Guomao Road South, Hualong Town, Panyu District, Guangzhou City, China Tel: +8620-8489-9499 Fax: +8620-8480-3343 Website: www.grandviewscreen.com www.grandviewscreen.com.cn

as figure 1. GPCM-E can be installed to the concrete- roof with ceiling or without ceiling,such as figure 2 and figure 3. 1 2 GPCM-E3540 GPCM-E4560 1-1 1-2 2-1 2-4 2-3 3-1 3-2 2-2 3-2 2-5 Connect the adjuster to GPCM Main Bar Overview, and then fasten the screws (accessory③ ) as figure 4. Afterward, slide the Adjustment Overview (projecter has been installed) to adjuster, and the fasten the screws (accessory ④) as figure 5. Parts GPCM-E is combined by GPCM and GPE GPCM Main Bar Overview 1-1 Fixation 1-2 Top Cap 2-1 Main Bar 2-2 Subsidiary Bar 2-3 Ornament Board of Main Bar 2-4 Ornament Board of Subsidiary Bar 2-5 Ornament Cap of Main Bar GPE Adjusting Overview 3-1 Adjuster 3-2 Horizontal Adjusting Button 3-3 Vertical Adjusting Button 3-4 Rotation Adjusting Screw 4-1 Installation Bracket 4-2 Installation Arm 4-3 Adjustable Screw 4-4 Sliding Installation Button 4-5 Installation Base Accessories: ① M5x35 Tapping Screw (3sets) ② M5x10 Philips Screw/ Washer/Spring Washer (4sets) ③ M4x6 Socket Cap Screw (6pcs) ④ M5x8 Philips Screw (6pcs) ⑤ M3x8 Philips Screw (4pcs) ⑥ M4x8 Philips Screw (4pcs) ⑦ M5x8 Philips Screw (4pcs) Scope for installation (Installation hole of projector): Maximum scope for installation:390mm diameter Minimum scope for installation:20mm diameter Note: Connect the installation arms to the projector conversely for different installation holes of projector. Scope Maximum diameter: 390mm Minimum diameter: 20mm Scope for installation (H is the distance between ceiling and projector) The H of GPCM-E3540 is 350mm~400mm The H of GPCM-E4560 is 450mm~600mm Scope Two steps of installation Two steps of installation figure 1 figure 2 figure 3 figure 5 figure 4 Details of installation Wires collection Take apart the ornament cap of main bar (2-5) after connecting the GPCM Main Bar Overview to the fixation (1-1), then stay the power cord into the storage gap. At last, re-install the ornament cap of main bar (2-5) as figure 7、 8 and 9. figure 6 figure 7 figure 8 4-1 4-2 4-3 4-4 4-5 3-4 H H