Atdec VFS-DH Installation Manual

Installation Guide VFS-DH Freestanding Dual Horizontal REQUIRED TOOLS • Phillips Head Screwdriver A Crossbar (x1) B VESA Plate (x2) C Upright Pole (x1) D Base (x1) K (Optional) Security Screw (x2) L Cable Ball (x6) E 3/5mm Allen Key (x1 each) F M8x50mm Screw (x1) G M6x25mm Cap Screw (x1) H Mounting Screw M4x16mm (x8) I Mounting Screw M4x12mm (x8) J Mounting Screw M4x10mm (x8) M Cable Clip (x4) COMPONENT CHECKLIST IMPORTANT INFORMATION ! Please ensure this product is installed as per these installation instructions. !� Each�VFS�Display�Head�supports�a�maximum�weight�as�per�above�weight�range�specification. !� This�product�supports�VESA�mounting�hole�configurations:�75x75mm�and�100x100mm.� !� The�manufacturer�accepts�no�responsibility�for�incorrect�installation. ! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be�within�the�stated�range.�Please�contact�Atdec�if�you�would�like�further�information. WEIGHT RANGE Per Monitor Flat Monitor 0�-�12kg�(0�-�26.5lb) Curved Monitor 0�-�9kg�(0�-�20lb) NOTE • 120mm (4.75”) max overall monitor depth. • 2kg�(4.4lb)�maximum�weight� difference�between�monitors.

1. Attach Upright Pole to Base 1.1 Attach the upright pole to the base as shown below. Ensure the cable slot faces towards the rear. Cable Slot USER BACK TIGHTEN FIRMLY Upright Pole M8x50mm Screw 5mm Allen Key 3. Attach the VESA plate to your monitor (Repeat steps 3 to 6 for each monitor) NOTE: Be sure to select a screw length that suits the monitor. 3.1 Check VESA mounting compatibility 3.2 Screw VESA plate to back of monitor using provided screws. 100mm 75mm 100mm 75mm Top of monitor Too short Too long OK 2. Attach crossbar and display heads 2.1 Attach crossbar to pole. 2.2 Slide display heads onto crossbar. OPEN 1 SLIDE DISPLAY HEAD ONTO CROSSBAR 2 REPLACE END CAP 3 CLOSE DISPLAY HEAD LEVER ONCE IN PLACE ON CROSSBAR. 4 HOLD SUPPORT IN PLACE TIGHTEN M6x25mm Cap Screw 5mm Allen Key CLAMP Cable slot to face back OPTIONAL BOLT THROUGH & GROMMET MOUNT Mount can also be bolted to work surface or via grommet hole with the Atdec Grommet Clamp (AC-GC),�sold�separately.

4. Attach your display to the VFS display head 4.1 Hook the top of the VESA plate onto the display head. ! While mounting the first monitor, carefully support mount to prevent tipping. 4.2 Press and hold the two buttons on the display head. Gently push bottom of VESA plate into display head. Release buttons to lock in place. 4.3 (Optional) Insert the security screw, and tighten using a phillips-head Screwdriver. 5. Adjust horizontal position of the monitor 5.1 Open the lever to loosen the display head. 5.2 Slide the display head to desired position. Note: support monitor weight to aid sliding. 5.3 If necessary, adjust the tension between the display head and the pole using the 5mm allen key supplied. 5.4 Close the lever to lock the display head in place. HOOK Back of Display OPEN LOOSEN TIGHTEN SLIDE CLOSE Release Button PUSH TIGHTEN Security Screw 6. Adjust the ball joint tension 7. Cable Management 6.1 If the monitors are not holding position or are stiff to move, adjust the tension plate by tightening or loosening the three screws. + - Note: Adjust 3 screws evenly in small increments Note: Support the monitor while making adjustments. 3mm Allen Key 7.1 Connect cables to your monitors. Then route them down to the table by inserting them into the cable slots in the crossbar and upright pole. Use either the cable balls or cable clips to secure them in place as shown. Leave slack in cables Cable Balls (x6) Leave slack in cables Cable Balls (x6) Cable Clips Note Ensure enough slack is left in cables to allow for movement. When the slot in each pole cannot be used, use the supplied cable clips to secure the display cables.

8.1 Remove monitors 8.3 Remove crossbar from pole 8.5 Lock display head onto pole No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20201207 OPTIONAL 8. Switch to a single monitor mount Preview 8.2 Slide display head off crossbar 8.4 Slide display head onto pole UNLOCK REMOVE END CAP SLIDE DISPLAY HEAD OFF CROSSBAR 3 1 2 Slot UNLOCK SLIDE DISPLAY HEAD ONTO POLE (Ensure tongue in display head aligns with slot in pole) Tongue 3 2 REMOVE POLE CAP 1 3 PRESS AND HOLD BUTTONS LIFT OFF MONITOR PULL OUT BOTTOM OF MONITOR 2 1 SUPPORT CROSSBAR UN-SCREW CROSSBAR (Use 5mm Allen Key) REMOVE CROSSBAR FROM POLE 2 1 3 REPLACE POLE CAP LOCK DISPLAY HEAD TO POLE Re-attach monitor following steps 4.1 to 4.3 2 1