Hanil Component R12 Manual 

Cat. No. : CP-R12 / CP-R6 Setting Temperature Setting temperature -10 to 40℃ (R12) / -20 to 40℃ (R6) Setting temp. limit Lid Open Stop Start Max. RPM : 4,800 rpm Max. RCF : 7,470 xg Max. RPM : 5,000 rpm Max. RCF : 7,261 xg Component R12 Component R6 Serial No. Installation Date Display Screen Status of RPM / RCF / Time / Temperature / Rotor ID / ACC / DEC / Program Setting Speed Press once : Setting RPM Press twice : Setting RCF Setting Time Up to < 100 hr Continuous run (00:00) View Settings Verifying the setting parameters during centrifugation Program Save / Call Saving a program (up to 100) Calling up a program Setting the Rotor ID manually Enter the rotor ID. manually, when rotor id is not identified automatically Setting ACC / DEC Rate ACC (0 ~ 9 steps, Max.9) DEC (0 ~ 9 steps, Natural DEC.0) Display & Control Panel Saving / Calling Up a Program Setting Run Parameters (RPM / RCF / Time / Temperature / ACC / DEC) Temperature range that stops operation when the temperature is lower or higher than the set temperature. Setting Temp. Limit Press a parameter to be changed Enter the desired values on the keypad Press the Enter button Press the Enter button Enter the desired program number on the keypad Press the Save or call button Press the Temp. limit button Press the Enter button Enter the desired temperature range on the keypad

sources, which correspond to the electrical requirements on the label attached to the device. Check the wall outlet is earth- grounded, surge-protected and can supply enough power. Connect the power cable to the distribution box, or install the plug and socket that are packed with the device. Switch off the device after use. Unplug the power plug before cleaning or unused for a long period of time. Check the Line Voltage Grounded Outlet Power Connection Switch Off the Device Quick Guide Component R12 / R6 Cat. No. : CP-R12 / CP-R6 Allow a safety clearance of 30 cm around the centrifuge during operation. Rotors Spread the grease lightly on the bucket where it contacts the rotor and the pivot. Remove any dust regularly from the ventilation slits on the left side of the device. There is a drain hose at the bottom of the device. The condensation water is automatically drained through the hose. Check and remove it regularly. Component R6 Component R12 30 cm 30 cm 30 cm Emergency Lid Open If the centrifuge lid cannot be opened, insert the provided T-wrench into the emergency release hole and turn it clockwise. (Before activating emergency open, switch off the device and wait for the rotor to stop.) Wipe up the moisture in the chamber with a dry cloth after use. Keep the lid open when not in use. Clean the chamber and rotor by wiping with a cloth soaked in mild detergent and dry completely. Keep the Chamber Dry Cleaning Check the rotor, buckets and tubes are free of scratchand crack before operation. Check the Accessories for Abnormalities Load tubes symmetrically into the rotor with identical amount. Load Tubes Symmetrically Place the lid on the wind shield rotor before centrifugation. Check the Lid After relocating the device or loading the rotor, balance them by using a leveler. If necessary, level the device by adjusting the ‘Leveling foot’ on the bottom of the device. Balancing the Centrifuge and Rotor 3.0KVA (Component R12) 5.0KVA (Component R6) 220~240V 50/60Hz Maintenance Electrical Safety Cautions for Use Rev.1 Proudly made by Jiyoung Shim, Hyewon Jeong Order & Inquiry l +82-2-3472-0727 l [email protected] l www.ihanil.com Service l +82-2-3452-8966 l [email protected] Before Operation After Operation Maintenance of Swing-Out Rotor Remove Dust Empty the Condensation Water Allow a Safety Clearance of 30 cm WS1000-6 WS2400-6 6 x 1,000 mL / Max. 5k 6 x 2,400 mL / Max. 4.8k