Strong SRT 5406 Operation & User’s Manual

• To avoid electric shock, do not open the unit. • There are no user-serviceable parts inside. Servicing can only be performed by qualified service personnel. • Connection can only be to a 240V AC mains supply. • All safety and operating instructions should be read before the product is operated. • All warnings on the product and in this user’s manual should be adhered to. • The antenna cable must be earthed. • Do not use attachments not recommended by the product manufacturer as they may cause hazards or damage the equipment. • Do not overload adaptors, wall sockets or extension cables as this can result in unit failure or electric shock. • For cleaning, use only a dry or lightly dampened cloth. Do not use liquid cleaners or aerosol cleaning products. • Do not place this product on an uneven surface. • Do not block the ventilation slots on the top of the unit.

This product has been manufactured in accordance with strict quality control procedures and is fully compliant with Australian specifications. Your new receiver will enable you to experience superior picture and sound quality, widescreen images, extra channels plus a variety of new features. • For a complete list of all of our digital television receivers— terrestrial and satellite—please go to our website: www.strong-technologies.com • For general enquiries, please email us at [email protected] • For technical assistance, please call our Technical Support Help Line on 1 800 820 030 Main Features • High Definition Multimedia Interface (HDMI) output • Decodes high definition and standard definition broadcasts • Component output (Y/Pb/Pr) • Dolby Digital audio output: S/PDIF optical • S-Video and Composite output • Plays MP3 music from a USB memory stick • Multi-video definitions: 576i/ 576p/720p/1080i • Auto and manual channel searching • Multi-language support • Multi-band selection: 7M and 8M • Tuner loop-through • CD-quality audio (mono and stereo) • Favourite channels and stations list • EPG: Electronic Program Guide • 16:9 and 4:3 aspect ratios • Signal level and quality indicators • Subtitles and teletext • Parental guidance locking • 8 timer event settings • USB port for software upgrades • COFDM demodulation • DVB/T and MPEG-2 compliant • Fully featured infra-red remote control

Overview ................................................................................................................................................................................ 3 Main Features........................................................................................................................................................................ 3 Checklist of Accessories ..................................................................................................................................................... 5 Controls and Indicators ....................................................................................................................................................... 6 Front panel.................................................................................................................................................. 6 Rear panel................................................................................................................................................... 7 Remote Control..................................................................................................................................................................... 8 Installing the batteries in the remote control ............................................................................................ 9 Quick Start........................................................................................................................................................................... 10 How to Connect................................................................................................................................................................... 11 Step 1: Connect to the antenna................................................................................................................. 11 Step 2: Choose an installation method...................................................................................................... 11 A: High Definition Multimedia Interface.................................................................................................. 12 B: Y/Pb/Pr (Component) using the supplied RCA blue–red–green cable............................................... 12 C. S-Video (Y/C) connection.................................................................................................................. 12 D: CVBS (Composite) using the supplied RCA red–white–yellow cable ................................................ 13 Step 3: Optional connections..................................................................................................................... 14 Dolby Digital .......................................................................................................................................... 14 Looping Out (for VCR recording) ........................................................................................................... 14 Getting Started.................................................................................................................................................................... 15 First-time use ............................................................................................................................................ 15 Operation ............................................................................................................................................................................. 16 Basic operations........................................................................................................................................ 16 Selecting a channel ............................................................................................................................... 16 Adjusting the volume ............................................................................................................................. 17 Getting channel Information................................................................................................................... 17 TV/Radio switching................................................................................................................................ 17 Closed captions..................................................................................................................................... 18 Teletext.................................................................................................................................................. 19 Picture freeze ........................................................................................................................................ 19 Favourites list............................................................................................................................................ 19 Adding channels or stations to your favourites list ................................................................................. 19 Selecting a favourite to watch or listen to............................................................................................... 21 Organising channels and stations ............................................................................................................. 21 Deleting channels and stations.............................................................................................................. 21 Re-sorting channels and stations........................................................................................................... 22 Playing music............................................................................................................................................ 23 Electronic Program Guide (EPG) .............................................................................................................. 24 Displaying program information ............................................................................................................. 24 Selecting a channel to watch from the EPG........................................................................................... 24 Rescanning for channels and stations....................................................................................................... 25 Multi-language and Dolby Digital broadcasting.......................................................................................... 27 User Settings....................................................................................................................................................................... 28 Audio–Visual (AV) settings........................................................................................................................ 28 System settings......................................................................................................................................... 29 PIN setting................................................................................................................................................. 31 Timer settings............................................................................................................................................ 32 System Maintenance .......................................................................................................................................................... 35 System information................................................................................................................................ 35 Software upgrades ................................................................................................................................ 35 Clearing and resetting data.................................................................................................................... 36 Troubleshooting.................................................................................................................................................................. 37 Support ................................................................................................................................................................................ 38 Specifications...................................................................................................................................................................... 39

The following accessories have been supplied with your . If any were not supplied, contact the retailer from whom you purchased the unit. User’s manual : 1 Remote control : 1 Batteries (AAA type) : 2 CVBS Composite video and audio cable (yellow, white, red) : 1 Y / Pb / Pr Component cable (blue, red, green) : 1

Front panel 1 To switch the receiver between stand-by mode and power-on mode. 2 To select the next channel, or next option in a menu. 3 To select the previous channel, or previous option in a menu. 1 2 3

IEC 169-24 female Input from terrestrial antenna 2 LOOP OUT IEC 169-24 female Loop-through output to VCR, etc. 3 USB USB 2.0 A-type cable Music and software upgrades 4 HDMI HDMI cable HDMI video-and-audio connection 5 S/PDIF Fibre optic Digital audio output (optical) 6 S-Video MINI-DIN S-VHS video output 7 Y/Pb/Pr RCA Component RCA cinch (green/blue/red) Component connection (Y/Pb/Pr) 8 RS-232 DB-9 Serial port 9 Video RCA RCA cinch( yellow) Composite video connection 10 Audio (Left and Right) RCA cinch • white: left audio • red: right audio Left and right audio for Component or Composite connection 11 Power switch — To turn unit on or off

important operating and maintenance instructions accompany the product. These are set out in this manual. It is highly recommended that you read this manual thoroughly before using the product. To reduce the risk of electric shock, do not remove any panel of the . Even when the unit is turned off, voltages may be present within it that are of sufficient magnitude to constitute a risk of electric shock. Remote Control 1. STANDBY: To switch to stand-by mode when the receiver is on (or vice versa) 2. Numeric Keys (0–9): To choose a channel directly, or to enter numeric information in a menu 3. TV/RAD: To switch between TV and radio (and vice versa) 4. EPG (Electronic Program Guide): To show the TV and radio program guide 5. MENU: To display the main menu, or return to a previous menu 6. CH (▲/▼): To change the channel, or to move the cursor up or down in a menu 7. VOL (e/f): To change the volume in viewing mode, or to change an option or setting in a menu 8. OK: To show the channel list in viewing mode, and to select an item (or confirm a choice) in a menu 9. FAV: To display the favourites list in viewing mode, and to select a favourite 10. RECALL: To return to the previous channel or station 11. SUB: To turn subtitles on or off 12. AUDIO: To choose speakers (left, right or stereo), audio format and audio language 13. MUTE: To turn the sound on or off 14. FORMAT: To cycle through the video definitions: 576i, 576p, 720p and 1080i 15. INFO: To show information about the current program

to normal viewing 17. PAGE / : To move to the next or previous page ( if there is more than one page) 18. PAUSE: To freeze the screen 19. ASPECT: To cycle through the aspect ratios: 16:9 and 4:3 20 .PAGE / : To move to the next or previous page ( if there is more than one page) 21. TXT: To show Teletext 22. USB: To lay music from a USB memory stick, or to upgrade the software Installing the batteries in the remote control 1. Press down on the retaining catch on the lid of the battery recess on the remote control and remove the lid. 2. Insert two AAA batteries into the recess. Be careful to insert the batteries as shown in the diagram inside the recess. 3. Replace the lid over the recess and gently push down on the lid until it snaps firmly into place.

using he cables provided. For detailed instructions, see “How to Connect” on page 11. Install batteries in the remote control. See page 9. Connect the to the antenna wall plate. See page 11. Using the supplied Component cable (blue–red–green) or the yellow lead of the supplied Composite cable, connect the to the TV. Make sure you match the colour of a lead with the colour of a socket. (This step provides video output to your TV.) See “How to Connect” on page 11. Connect the white and red leads of the Composite cable between the and the TV, again matching the colour of a lead with the colour of a socket. (This step provides audio output to your TV.) See “How to Connect” on page 11. Turn on the and the TV. The Strong Technologies banner appears on your TV screen, followed by a message asking if you want to automatically search for channels and stations. (If you don’t see the banner and message, press EXIT and then FORMAT on the remote control until you do.) Press OK to automatically scan for digital broadcasters in your area. When the scanning is finished, the menu closes and a local digital TV channel will be showing. See “Basic operations” on page 16 for general instructions on using the to select TV channels and radio stations. 1 2 3 4 5 6

Refer to the diagram on page 8 for the location of the sockets identified by numbers in the procedures in this section. Make sure you have installed the batteries in the remote control before you begin connecting the to your TV. Depending on the connection method you choose, you may need to adjust certain settings using the remote control before you can see a digital broadcast. Step 1: Connect to the antenna Connect the antenna lead coming from your antenna wall plate to the TV ANT IN socket on the (socket 1). TIP: You probably already have an antnna lead coming from your antenna wall plate to the TV ANT IN socket on the back of your TV. If so, simply unplug the lead at the TV and plug it into the TV ANT IN socket on the . Step 2: Choose an installation method There are a number of methods of connecting the . These methods are labelled A, B, C and D below. NOTE: The various video connection options available provide differing degrees of video quality. In ascending order of quality, these connections are Composite (good), S-Video (better), Component (better again) and HDMI (best).

If your TV has an HDMI socket, connect an HDMI cable between the HDMI socket on the (socket 4) and the HDMI socket on your TV. A HDMI connection incorporates video and audio. You do not need to make separate connections for audio. An HDMI cable is not provided with the . B: Y/Pb/Pr (Component) using the supplied RCA blue–red–green cable For Component video, connect to your TV with the supplied Y/Pb/Pr Component cable (with blue, red and green leads). Connect the leads between the Y, Pb and Pr sockets on the (socket group 7, taking care to match the colour of a lead with the colour of the socket), and the corresponding Component sockets on your TV. (The Component sockets on the TV have the same colour-coding.) You will need to make separate connections for left and right audio via the audio sockets in socket group 9. This can be done using the supplied RCA cable. (Match the colour of the plugs with the colour of the sockets.) C. S-Video (Y/C) connection If your TV has a 4-pin Mini Din S-Video socket, you can connect an S-Video cable between socket 6 on the and the corresponding S-Video socket on your TV. (An S-Video cable is not supplied.) You will need to make separate connections for left and right audio via the audio sockets in socket group 9. This can be done using the supplied RCA cable. (Match the colour of the plugs—white and red—with the colour of the sockets.)

576i. However, the is designed primarily to output higher quality signals—signals with a video definition of 1080i—and this is the default setting. As a result, you will see only a blank screen when you first make an S-Video connection. To get proper reception, press the FORMAT button on the remote control. Keep doing so until a picture appears. (The video definition rates will appear on the screen on the front of the . The rate you need is 576i.) D: CVBS (Composite) using the supplied RCA red–white–yellow cable Using the appropriate socket colour-coding on sockets 8 and 9, you can connect to your TV with the supplied red–white–yellow RCA cable. This gives you CVBS (Composite Video) and MPEG-2 stereo audio. For video, connect the yellow RCA lead between the yellow video socket (socket 8) on the and the corresponding socket on your TV. For audio, connect the same RCA cable between the white and red sockets in socket group 9 and the corresponding sockets on your TV. Match the colour of the leads—white and red—with the colour of the sockets. (All three leads of the cable—yellow, white and red—should be plugged into the same socket group on your TV.) IMPORTANT NOTE: A CVBS connection will only output signals with a video definition of 576i. However, the is designed primarily to output higher quality signals—signals with a video definition of 1080i—and this is the default setting. As a result, you will see only a blank screen when you first make a CVBS connection. To get proper reception, press the FORMAT button on the remote control. Keep doing so until a picture appears. (The video definition rates will appear on the screen on the front of the . The rate you need is 576i.)

Dolby Digital Dolby digital bitstream audio S/PDIF can be achieved using an optical cable. (This cable is not supplied.) The cable should be connected between socket 5 on the and the S/PDIF socket on your Dolby Digital decoder amplifier. Looping Out (for VCR recording) In order to watch one channel while recording another on a VCR, connect an RF cable (not supplied) between the LOOP OUT socket on the (socket 2) and the RF IN socket on your VCR. Note that VCR recordings are only analogue, not digital.

to your antenna and to your television, you need to: 1. Turn on the television. 2. Plug the into mains power and turn on the power at the mains switch. 3. Turn on the using the power-on switch on the back of the receiver (number 10 in the diagram on page 7). 4. Select the video or AV input channel to which the is connected: this can be done by pressing the TV/AV or VIDEO button on your TV remote control. (Refer to your TV user’s manual for instructions.) The Strong Technologies banner appears on your TV screen, followed by a message asking if you want to automatically search for channels and stations. (If you don’t see the banner and message, press EXIT and then FORMAT on the remote control until you do.) 5. To search for available channels and stations, press OK on the remote control. The Auto window appears and the searching begins. If you want to search for channels and stations yourself, s ee “Rescanning for channels and stations” on page 25 for instructions and ignore the rest of this procedure. As channels and stations are found, they are displayed on the Auto window. When the can find no more channels and stations, the search ends and one of the TV stations found will appear on the screen. NOTE: You can now start watching digital TV stations and listening to digital radio stations. However, there are settings that you should consider that will improve your enjoyment of your . These are explained in “User Settings” on page 28. But if you want to start watching TV straight away, see “Basic operations ” on page 16 for instructions.

There are a number of ways to select a TV channel or radio station: • Number pad on the remote control: If you know the channel number, enter the number using the number keys on the remote control and then press OK. (If you don’t press OK, the channel selected appears after approximately 2 seconds.) To choose a radio station using the number keys, press TV/RADIO first and then enter the number. (For example, 201 is the number for ABC Dig Jazz.) NOTE: The uses the Logical Channel Numbering system (LCN) by default. Some samples of primary LCN channel numbers are: 1 = Ten network and affiliates 2 = ABC 3 = SBS 7 = Seven network and affiliates 9 = Nine network and affiliates Secondary channels can be selected by pressing the primary number followed by another number. (For example, pressing 2 gives you ABC1, and pressing 22 gives you ABC2.) • Channel list: Press OK on the remote control. This displays the channel list. (To list radio stations instead of TV channels, press TV/RADIO before pressing OK.) Press CHd or CHc on the remote control until the channel or station you want is highlighted and then press OK. TIP: Press a PAGE button to quickly scroll through a long list of channels.

select TV Channel or Radio Channel and press OK. Press CHd or CHc on the remote control until the channel or station you want is highlighted and then press OK. • Favourites list: Press FAV on the remote control to see the first channel or station in your favourites list. Press CHd or CHc to see each favourite in turn. Pause at the station or channel you want. See “Favourites” on page 19 for instructions on creating a favourites list. • Scroll: Press CHd or CHc on the remote control to scroll through the channels in channel number order. (You can also scroll through the channels in order by pressing the channel up and channel down buttons on the front panel of the .) • By EPG: Press EPG on the remote control, select the channel from the electronic program guide (EPG), and press EPG again. The EPG is explained on page 24. • Previous channel: Press the RECALL button to return to the previous channel or station. Adjusting the volume While you are watching TV or listening to the radio, press VOLe or VOLf on the remote control to decrease or increase the volume respectively. Turning off the sound (muting) To turn off the sound altogether, press the MUTE button on the remote control (button 12 in the diagram on page 8). The mute icon is displayed on the screen. Press the MUTE button again to restore the sound. Getting channel Information • Press INFO on the remote control to display the information banner. Information about the current and the next program is provided. The headings along the top of the banner are HD (High Definition), AC3 (Digital Dolby), TTX (Teletext), SUB (Subtitles) and FAV (Favourites). A heading will be highlighted if the corresponding option applies (for example, if the broadcast is in high definition, if subtitles are available, if the current channel is in your favourites list, and do on). The information banner will stay displayed for a few seconds. To hide it sooner, press EXIT on the remote control. TV/Radio switching Press TV/RADIO on the remote control to switch between TV channels and radio stations (or vice versa).

hard-of-hearing. To turn on closed captions (or turn them off): 1. Press the SUB button on the remote control. The Subtitle window appears. 2. With Mode highlighted, press VOLe or VOLf until the option you want—On or Off—is shown. 3. If the subtitles are being broadcast in more than one language and you want to choose a language other than the one shown on the screen, press CHd to highlight the Language option and then press VOLe or VOLf until the language you want is shown. 3. Press OK.

data. 1. Select a channel that is broadcasting teletext. 2. Press TXT on the remote control. 3. If necessary, select the language of the teletext service. 4. Press OK. 5. Select a teletext page by pressing the corresponding number or colour button on the remote control. Press EXIT to cancel teletext and return to normal viewing. Picture freeze • Press PAUSE on the remote control to freeze the display. • Press PAUSE again to resume normal viewing. Favourites list You can create a favourites list of channels and then select a channel from that list. This makes it easier to choose and switch between channels if there are many channels available in your area. You display your favourites lists by pressing FAV on the remote control. You then press CHd or CHc to step through each favourite. Stop pressing when you reach the favourite you want. Adding channels or stations to your favourites list Follow this procedure to add channels or stations to your favourites list, or to remove them. 1. Press MENU on the remote control. The Main Menu appears. 2. If Edit Program is not highlighted in the main menu, press CHd or CHc until it is and then press OK. The Edit Program menu appears.

make a radio station a favourite, make sure Edit Radio is highlighted. With the option you want highlighted, press OK. A list of channels or stations appears. 4. Press CHd or CHc until the channel or station you want to select is highlighted. 5. Press the AUDIO button (the green button) on the remote control to mark the highlighted channel or station as a favourite (or to mark it for removal from your favourites list). An icon of a heart appears beside the channel or station name to indicate that it is to become a favourite (or the icon disappears if it was already a a favourite). 6. If you want to select another channel or station a favourite, repeat from step 4. 7. Press MENU or EXIT. A message appears asking you to confirm that you want to save the changes. 8. To proceed, press OK. To cancel, press MENU or EXIT. 9. Press MENU or EXIT. to return to normal viewing.

1. Press FAV on the remote control. The first channel or station or channel in your favourites list appears. Note that the information panel reads FAV channel. 2. If necessary, press FAV again until the channel you want to view appears. The FAV information banner disapears after a few seconds. Organising channels and stations The Edit Program option on the Main Menu enables you to delete and sort channels and stations. Deleting channels and stations You can delete channels and stations that you are never likely to watch or listen to. If you want to re-instate a channel or station that you have deleted, you will need to rescan for it. See “Rescanning for channels and stations” on page 25 for instructions. 1. Press MENU on the remote control. The Main Menu appears. 2. If Edit Program is not highlighted on the main menu, press CHd or CHc until it is and then press OK. The Edit Program menu appears. 3. If you want to delete a channel, make sure Edit TV is highlighted; or if you want to delete a station, make sure Edit Radio is highlighted. With the option you want highlighted, press OK. A list of channels or stations appears.

5. Press the SUB button on the remote control to mark the highlighted channel or station for deletion. An icon of a cross appears beside the channel or station name to indicate that it is to be deleted. (To unmark the highlighted channel or station, press the SUB button again.) 6. If you want to delete another channel or station, repeat from step 4. 7. Press MENU or EXIT. A message appears asking you to confirm that you want to save the changes (that is, delete the channels or stations you have marked for deletion). 8. To proceed with the deletion, press OK. To cancel the deletion, press MENU or EXIT. Re-sorting channels and stations You can sort channels and stations in number order or alphabetical order, or sort them so that your favourite channels and stations are listed at the top of the channel or station list. 1. Press MENU on the remote control. The Main Menu appears. 2. If Edit Program is not highlighted in the main menu, press CHd or CHc until it is and then press OK. The Edit Program menu appears. 3. If you want to resort a channel, make sure Edit TV is highlighted; if you want to resort a station, make sure Edit Radio is highlighted. With the option you want highlighted, press OK. A list of channels or stations appears.

To sort the channels or stations numerical order, press the USB button (the yellow button) on the remote control. To sort the channels or stations in alphabetic order, press the USB button (the yellow button) on the remote control. (The USB button toggles the sort order between numerical and alphabetical order, that is, selects one order and then the other.) To sort the channels or stations so that your favourites are always at the top of the channel or station list, press the TXT button (the blue button) on the remote control. 5. Press MENU or EXIT. A message appears asking you to confirm that you want to save the changes (that is, the new sort order). 6. To proceed, press OK. To cancel, press MENU or EXIT. Playing music You can play MP3 music through your TV speakers. The music files need to be on a USB memory stick (not supplied with the ). They must be at the root (or top) level on the memory stick, not inside a folder or directory. 1. Press the USB button (the yellow button) in the remote control. The USB File List screen appears. 2. Press CHd or CHc to highlight the track you want to play and press OK. 3. To play another track, repeat from step 2.

Electronic Program Guide (EPG) Some providers broadcast information about their programs. This information is available on screen via an electronic program guide, displayed by pressing EPG on the remote control. An example is shown below. You can navigate through the EPG looking for information about channels and programs (explained in the next section) or press EPG or EXIT to close the guide. Displaying program information The information displayed when you press EPG is information about the channel that is showing at the time. At the top left of the screen is information about the current program on that channel; at the right of the screen is a list of upcoming programs. • To display information about the programs on another channel, press CHd or CHc until the channel you want information about is highlighted at the bottom left of the screen. To display more information than is currently shown about a selected channel, you can move between the channel name pane (at the bottom left of the window) and the program name pane (at the right of the window) and vice versa. • To move to the program pane, press OK. • To display program information for another day, press OK and then press VOLe or VOLf to step through the days. • To scroll through the programs for a day, press CHd or CHc. • To move back to the channel list in the left pane of the window, press EXIT. Selecting a channel to watch from the EPG 1. With the channel name panel selected, press CHd or CHc until the channel you want to watch is selected. 2. Press EPG or EXIT. The current program of the selected channel is now showing.

The Install option on the main menu enables you to scan for—that is, detect—digital TV and radio stations available in your area. You will need to rescan if new channels or stations become available, if you want to reinstate a channel or station you have deleted, or if you move to a new location. There are two scanning options: • Auto Search The will automatically search for all digital TV and radio stations it can detect and store their details. • Manual Search This option lets you search for a particular channel (or all channels from a specified broadcaster). Automatic Search 1. Press MENU on the remote control. 2. If Install is not highlighted on the main menu, press CHd or CHc until it is and then press OK. The Install sub-menu appears. 3. If Auto Search is not highlighted on the sub-menu, press CHd or CHc until it is and then press OK. The Auto window appears, and the search begins automatically. When the search is finished, a channel that has been found will begin playing. Manual Searching NOTE: Automatic searching (described above) is suitable in most cases. You might use manual searching if you have deleted a channel and now want to access it again. In this case, you would just search for that particular channel. 1. Press MENU on the remote control. 2. If Install is not highlighted on the main menu, press CHd or CHc until it is and then press OK. The Install sub-menu appears. 3. If Manual Search is not highlighted on the sub-menu, press CHd or CHc until it is and then press OK. The Manual Search window appears.

within a particular bandwidth: 7 or 8 MHz). 4. To search for a channel by its number, select that number in the Channel No field. 5. To search for all channels broadcast on a particular frequency, press CHd or CHc until the Frequency field is highlighted and enter the frequency using the number keys on the remote control. 6. To restrict the search to broadcasts within a particular bandwidth, press CHd or CHc until the Bandwidth field is highlighted and then press VOLe or VOLf until the bandwidth you want is shown. TIP: To avoid a fruitless search, check the strength and quality of the signal beforehand. These are shown by the Level and SNR bars at the bottom of the screen. Poor strength or quality indicates that it may be difficult to scan for that channel or that the reception might be too poor for you to comfortably watch the channel. 7. Press OK to begin scanning. When the search is finished, the channel will begin playing if it has been found; otherwise the previous channel will reappear.

If a channel is being broadcast in more than one audio language, you can choose which language to listen to. Similarly, if a channel is being broadcast in more than one audio format, you can choose which format to listen to. 1. Press the AUDIO button (the green button) on the remote control. The Audio setting window appears. 2. If more than one audio language or format is being broadcast, pressing VOLe or VOLf will cycle through each language and format. Choose a language and format and press CHd. If a channel is being broadcast in Dolby Digital, the language will be shown with an AC3 suffix, as in English (AC3). Non-Dolby broadcasts will have an MP2 suffix, as in English (MP2). 3. You can also select the output mode for the audio language: stereo, left speaker or right speaker. With the Channel option highlighted, press VOLe or VOLf until the output mode you want is highlighted. 4. Press OK or EXIT to close the Audio setting window and return to normal viewing.

1. Press MENU on the remote control. The Main Menu appears. 2. If System Setting is not highlighted on the main menu, press CHd or CHc until it is and then press OK. The System Setting menu appears. 3. If AV Setting is not highlighted on the menu, press CHd or CHc until it is and then press OK. The AV Setting menu appears. With this menu you can control the following settings: • Aspect ratio – 4:3 or 16:9 • Aspect mode – Full screen, Letterbox or Pan & Scan • Video definition – 576i, 576p, 720p and 1080i • Video output – YPbPr or YC • S/PDIF output – PCM or AC3

between the and your TV. For example: • If you have used an S-Video or a Composite connection, the Video def setting must be set to 576i. • If you have used an S-Video connection, the Video output setting must be set to YC. • If you have used an HDMI connection, the Video output setting must be set to YPbPr. • If you have connected the to a Dolby Digital decoder amplifier, the S/PDIF output setting must be set to AC3. 4. Select an option you want to change. If necessary, press CHd or CHc until the option is highlighted. 5. With the option you want to change highlighted, press VOLe or VOLf to step through the allowable values (shown in the panel at the right of the screen). Stop when the value you want is displayed. 6. If there is another option you want to change, repeat this procedure from step 4. 7. When you have finished, press OK. 8. A message appears asking you to confirm that you want to save the changes. To proceed, press OK. To cancel, press MENU or EXIT. 9. Press EXIT until you return to normal viewing. System settings 1. Press MENU on the remote control. The Main Menu appears. 2. If System Setting is not highlighted on the main menu, press CHd or CHc until it is and then press OK. The System Setting menu appears. 3. If Sys Setting is not highlighted on the menu, press CHd or CHc until it is and then press OK. The Sys Setting menu appears.

• Language for the on-screen menus • Level of parental guidance (All, R and above, AV and above, MA and above, M and above, PG and above and G above) • Time zone • Transparency (that is, how much of the picture is visible through an information panel) Note that the level of parental guidance (as determined by the PG block level setting) is controlled by a password. For example, if you have MA and above, then any program with a classification of MA or higher will be blocked unless the unit’s password is entered. The default password is 0000. You can change the password. See the next section for instructions. 4. Select an option you want to change. If necessary, press CHd or CHc until the option is highlighted. 5. With the option you want to change highlighted, press VOLe or VOLf to step through the allowable values (shown in the panel at the right of the screen). Stop when the value you want is displayed. 6. If there is another option you want to change, repeat this procedure from step 4. 7. When you have finished, press OK. 8. A message appears asking you to confirm that you want to save the changes. To proceed, press OK. To cancel, press MENU or EXIT. 9. Press EXIT until you return to normal viewing.

The PIN is required if you have enabled the parental lock (see “System settings” on page 29). To chyange the PIN: 1. Press MENU on the remote control. The Main Menu appears. 2. If System Setting is not highlighted in the main menu, press CHd or CHc until it is and then press OK. The System Setting menu appears. 3. If Pin Setting is not highlighted, press CHd or CHc until it is and then press OK. The Pin Setting menu appears. 4. If you are changing the default or current PIN, make sure that Enable is selected for the Pin Status option. (If you are restoring the default PIN, press VOLe or VOLf to change this setting to Disable, press OK and ignore he rest of this procedure.) 5. Press CHd to move to the Old pin option and enter the current PIN using the number keys on the remote control. (If you haven’t previously changed the PIN, this will be the default PIN: 0000.) 6. Press CHd to move to the New pin option and enter a new PIN. (A PIN must be four digits long.) 7. Press CHd to move to the Confirm pin option and re-enter the new PIN. 8. Press OK to save your changes, and then EXIT to return to normal viewing.

will turn off. Follow this procedure to set or change a timer. 1. Press MENU on the remote control. The Main Menu appears. 2. If System Setting is not highlighted in the main menu, press CHd or CHc until it is and then press OK. The System Setting menu appears. 3. If Timer Setting is not highlighted, press CHd or CHc until it is and then press OK. The Timer List window appears. 4. If necessary, press CHd or CHc until the timer you want to select is highlighted and then press OK. The Timer Edit screen appears.

6. If you are setting a new timer, the Status field will read Disable. Press VOLe or VOLf to change this setting to Enable. 7. If you have selected a timer that has already been set and want to cancel it, press VOLe or VOLf to change the Status setting to Disable. Press the SUB button on the remote control to save your change, and then ignore the rest of this procedure. 8. All the timer options should now be available to you (see below). Press CHd to select the Cycle option. You can set the timer to activate only once, every day or every week. Press VOLe or VOLf until the cycle option you want is displayed. 9. Press CHd to select the Timer Service option. You can set the timer to come on (Wake Up) or turn off (Sleep). Press VOLe or VOLf until the timer service option you want is displayed. 10. Press CHd. If you chose One Time or Every Week for the Cycle option, the Date option will now be selected. Use the number keys on the remote control to enter the date this timer will activate (or first activate) and then press CHd. 11. Depending on what option you chose for Timer Service at step 9, the option now selected will either be labelled Wake Up or Sleep Time. Use the number keys on the remote control to enter the time you what the to turn on or turn off and then press CHd. Note that times must be entered using the 24-hour clock format. For example, 8 o’clock in the morning is entered as 0800, while 8 o’clock in the evening is entered as 2000. 12. If you chose Wake Up for Timer Service at step 9, the Channel option will now be highlighted. If you want to change the channel currently shown, press VOLe or VOLf until the channel you

13. Press the SUB button on the remote control. Your timer settings are saved. 14. Repeatedly press EXIT until you return to normal viewing.

as new versions become available. Information about the current version (and information about the hardware) is available from the menu to help you determine if you need to upgrade. This information might also be useful if you need to obtain technical support from Strong Technologies. You can also reset the by reinstating the default settings it had when it left the factory. System information To display system information about your , such as the model number, software version, hardware version: 1. Press MENU on the remote control. The Main Menu screen appears. 2. If System Info is not highlighted on the menu, press CHd or CHc until it is and then press OK. The System Info window appears. Make a note of the information on this window if you are intending to contact Strong Technologies for technical support. 3. Press EXIT or MENU twice to return to normal viewing. Software upgrades If a new version of the software becomes available, you can download the software to your PC and then transfer it to your . You will need a USB memory stick (not supplied with the ). Watch the Strong Technologies website for announcements of software upgrades. 1. Once you have obtained an upgrade file, transfer it to a USB memory stick. You need to place the file at the root (or top) level on the memory stick, not inside a folder or directory. 2. Insert the stick in the USB port on the rear of the (socket 3 in the diagram on page 7). 3. Press USB (the yellow button on the remote control). The USB File List appears.

and then press OK. The upgrade process may take a few minutes. When it is completed, a message appears at the bottom of the USB File List advising that you must now reset the . 5. Press EXIT and then follow the procedure in the next section to reset the . Clearing and resetting data You can reset the , by restoring the unit to the default settings it had when it left the factory. This clears all channels, stations, preferences and other user settings. You will need to rescan for channels and stations before you can continue watching digital TV or listening to digital radio. WARNING: This procedure returns the to its default factory settings. All data (such as time zone, channels, stations and timers) will be lost. 1. Press MENU on the remote control. The Main Menu screen appears. 2. If System Setting is not highlighted on the menu, press CHd or CHc until it is and then press OK. The System Setting menu appears. 3. If Factory Default is not highlighted on the menu, press CHd or CHc until it is and then press OK. 4. A warning message appears asking if you are sure you want to clear all services and restore factory settings. To continue, press OK. To cancel, press MENU or EXIT and ignore the rest of this procedure. 5. Another message appears asking if you want the to automatically search for channels and stations. To accept the automatic search press OK; otherwise, press MENU or EXIT. NOTE: If you proceed with resetting the factory defaults and get a blank screen, press EXIT, and then press FORMAT until something appears on your screen. 6. if you didn’t accept an automatic search, the No Service! message appears on the screen. You will now have to search for channels an stations yourself. See “Rescanning for channels and stations” on page 25 for instructions. If you accepted an automatic search, the Auto window appears and the search commences.

a PC will do from time to time). In this case, you should disconnect the from mains power, wait 30 seconds and then reconnect it to mains power. If the unit is still not operating correctly, refer to the following table for the indicated problem and likely solution. Symptoms Possible causes Solution Indicators on front panel do not light up AC power cord is not connected Check that the power cord is plugged into the wall socket. Make sure the power switch is on. The cables connecting the TV and the receiver are not properly connected Make sure that the correct cable is connected between the TV and the receiver, and that the antenna is connected. The TV mode is not correct Check that the correct video or AV input has been selected on your TV. No picture and sound Incorrect video definition If you have a Composite or S-Video connection to your TV, video definition must be set to 576i. Press EXIT and then FORMAT on the remote control until you see a picture. Insufficient signal strength Check that the antenna cable is securely plugged in and that the signal is adequate. Picture and/or audio glitch Electrical interference Check that all antenna cabling is quad- shielded. The receiver or TV is in mute mode Press the MUTE button on the receiver and on the TV. No sound Initial volume level has not been set on your TV Select the desired TV volume level using the TV remote control. Batteries not inserted Insert batteries Batteries are flat Change the batteries in the remote control. Remote control is not working Remote control is outside the range of operation Aim the remote control directly at the receiver. Files are of wrong format. Check that the format is, MP3. Music files on a USB memory stick don’t appear Files are not at the root or top level. Move the files out of folders or directories.

Please call our Technical Support Help Line on 1800 820 030 For General Enquiries: Please email us at: [email protected] Product Return Tracking: If you need to send your receiver to Strong Technologies for repair or evaluation, please keep a record of the unit’s serial number. This will ensure ease of tracking and identification on your behalf.

IEC 169-2 Female Output Connector – RF Loop Out IEC 162-2 Male Frequency range 174MHz–230MHz, 474MHz–868MHz Input impedance 75Ω IF bandwidth 7 and 8 MHz (switchable) Code Rate 1/2, 2/3, 3/4, 5/6, 7/8 Tuner & Channel Decoder Guard Interval 1/4, 1/8, 1/16, 1/32 Standard MPEG-2 [email protected] 1920 × 1080 @ 50MHz MPEG Transport Stream Rate 64 Mbps Profile Level MPEG-2 [email protected] 1920 × 1080 @ 50MHz Input Rate 80 Mbps Aspect Ratio 4:3, Letter Box, 16:9, Pan & Scan Video Decoding Video Resolution 1080i, 720p, 576p, 576i Standard MPEG Layer 1,2, 3; Dolby AC-3, 12S S/PDIF Audio Decoding Channels Single, Dual Mono, Stereo, Joint Stereo, Dolby Digital bit-streams Main Processor ARM926 Main System Memory 4Mb Flash; 64Mb SDRAM HDMI HDMI 1.2 connector ((with HDCP copy protection) Video Component Y / Pb / Pr Component YUV Video SVHS 4-pin Din Connector Video Composite RCA/Cinch, Video Output (CVBS) S/PDIF Optical Digital Audio Output Audio & Video In/Out USB USB 2.0 Input Voltage 100–240V AC Power Consumption 20W maximum，MEPS Compliant Protection Seprate internal fuse Power Supply Type Switch-mode Dimensions W250mm x H38mm x D175mm (case only)/185mm (to end of connectors) Weight 1.9 kg Physical Optimum operating temperature 0–50°C

60 WEDGEWOOD ROAD, HALLAM, VICTORIA 3803 PH: +61 3 8795 7990 FAX: +61 3 8795 7991 TECHNICAL SUPPORT: 1800 820 030 STRONG & CO. (FAR EAST), LTD. P. O. BOX 85, YOKOHAMA, KANAGAWA-KEN JAPAN 231-91 FAX: +81 45 651-1842 www.strong-technologies.com Email: [email protected] © Strong Technologies Pty Ltd., 2009