Assa Abloy HES 660 Installation Instructions

in door opening solutions Product Components 3 SOLENOID VOLTAGE 12VDC 24VDC ELECTRICAL RATINGS FOR SOLENOID CONTINUOUS DUTY 12VDC 48 24VDC 192 Resistance in Ohms Amps Seated Electrical Specifications Operating Voltage +/- 10% Watts Seated STANDARD INTERMITTENT DUTY PRELOAD 3 3 250mA 125mA 12VDC 17 24VDC 67.8 8.4 8.4 700mA 350mA MINIMUM WIRE GAUGE REQUIREMENTS 200 feet or less 200 - 300 feet 300 - 400 feet 14 gauge 12 gauge 12 gauge 18 gauge 18 gauge 16 gauge 5 6 1 2 3 Hook Bracket Assembly 660 Multi-Purpose Lock Body Lock Mounting Brackets 4 5 6 #6-32 X 3/16” Screws #10 X 1/2” Screws #8-32 X 5/8” Screw HES, Inc. Phoenix, AZ 85044 800-626-7590 www.hesinnovations.com

Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty. Prepare Cabinet/Drawer Finish Installing DIAGRAM 1: MOUNTING BRACKET INSTALLATION DIAGRAM 2: #8-32 X 5/8” SCREW INSTALLATION #8-32 X 5/8” SCREW 6. If lock body adjustment is needed to ensure a smooth capture and release of the hook bracket assembly, loosen the #10 X 1/2” and #6-32 X 3/16“ screws to adjust the Multi-Purpose Lock Body until desired clearance is reached. 7. If additional stability is desired, drill two 1/16” pilot holes and use two remaining #10 X 1/2” screws for final lockdown of the Multi-Purpose Lock Body as illustrated in Diagram 6, on Page 4. 8. If the optional key override is used, prepare the cabinet/drawer as illustrated in Diagram 7, on Page 4. WARNING: The Multi-Purpose Lock Body must be wired to a power source prior to insertion of the Hook Bracket Assembly. Failure to do so may result in a permanently locked cabinet/drawer. 1. Attach both Lock Mounting Brackets to the Multi-Purpose Lock Body using four #6-32 x 3/16” screws as illustrated in Diagram 1. 2. To prevent accidental capture of the Hook Bracket Assembly prior to the Multi-Purpose Lock Body being wired, gently thread the #8-32 X 5/8” screw into the #8-32 threaded hole depicted in Diagram 2. The #8-32 X 5/8“ screw must only be tightened snug by hand. When installed the #8-32 X 5/8” screw will prevent the capture of the Hook Bracket Assembly by the Multi-Purpose Lock Body. When wiring is complete, remove the #8-32 X 5/8” screw. The Multi-Purpose Lock Body will now be able to capture and electrically release the Hook Bracket Assembly. 4. Refer to Diagram 4 on page 3 to connect power to the Multi-Purpose Lock Body. If your Multi-Purpose Lock is equipped with the RJ-45 option, a diagram for pin assignments is also provided on page 3, Diagram 4. If applicable, the LBSM should also be electrically connected at this time. Remove the #8-32 X 5/8” screw installed in step 2. Verify catch and release of the unmounted Hook Bracket Assembly after power is connected. 5. Mark mounting holes for the Hook Bracket Assembly as illustrated on page 4, Diagram 5. Drill two 1/16” X 1/2” deep pilot holes for the Hook Bracket Assembly, and mount the Hook Bracket Assembly using two #10 X 1/2” screws. 3. Drill four 1/16” diameter pilot holes in the cabinet using the Mounting Template on page 3, and mount the Multi-Purpose Lock Body to the inside of the cabinet/drawer using four #10 X 1/2” screws. *SHOWN IN LH CONFIG

Align dotted line with outer edge of cabinet. Tape Model 660 Mounting Template to inside surface of cabinet. Drill four 1/16” holes through paper template. Model 660 Mounting Template FOLD LINE ON EDGE OF DOOR/DRAWER FOLD LINE ON EDGE OF CABINET MODEL 660 LOCK ASSEMBLY RED + BLACK - LBSM WIRING* White Orange Normally Open Green Normally Closed Common POWER WIRING* RED BLACK Negative - Positive + *If applicable *CAUTION! The Multi-Purpose Lock Body is provided as either a 12 or 24 volt unit. Verify the power supply output before operating this device. White Orange Green o O g B b G br BR 1 2 3 4 5 6 7 8 PIN4: LBSM (COMMON) - BLUE PIN5: POWER (NEGATIVE) - BLUE/WHITE PIN6: LBSM (NORMALLY CLOSED) - GREEN PIN7: POWER (POSITIVE) - BROWN/WHITE PIN8: LBSM (NORMALLY OPEN) - BROWN Clip is pointed away from you RJ-45 PLUG PIN1 DIAGRAM 3: MOUNTING TEMPLATE DIAGRAM 4: POWER & LBSM SWITCH WIRING RJ-45 OPTION 3

X=1/4” + R1 Y= 2-1/8” + R1 X R1 PADDLE: 660 KO OPTION MOUNTED TO DOOR/DRAWER 1/4” + R1 DIAGRAM 6: FINAL LOCKDOWN DIAGRAM 7: OPTIONAL KEY OVERRIDE DIAGRAM 8: DIMENSIONS 4 Installation Directions Inside surface of Cabinet 2-1/8” + R1 Y 3056006.001 rev B. © 2012 HES, Inc. (2) #10 X 1/2” SCREWS FOR FINAL LOCKDOWN 1-7/8” [46.9]