CyberData 011102 Installation Quick Reference

© 2015, CyberData Corporation, ALL RIGHTS RESERVED 930319L Quick Reference The IP Endpoint Company 4.00 [101.6] 120° VoIP Speaker Mounting Template Speaker Hole Diameter: 7.50 [190.5] Screw Hole Diameter: 0.1875 [4.75] Dimensions are in inches [millimeter] The Singlewire-enabled VoIP Ceiling Speaker is compatible with InformaCast Version 4.0 and higher. Typical System Installation Getting Started • Download the Singlewire-enabled VoIP Ceiling Speaker Operations Guide PDF file from the Singlewire Speaker Documentation page at: http://www.cyberdata.net/products/voip/digitalanalog/singlewirespeaker/docs.html • Create a plan for the locations of your speakers. • WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes. • WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. • WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant. • WARNING: The device enclosure is not rated for any AC voltages! Parts Parameter Factory Default Setting IP Addressing DHCP IP Addressa a. Default if there is not a DHCP server present. 10.10.10.10 Web Access Username admin Web Access Password admin Subnet Maska 255.0.0.0 Default Gatewaya 10.0.0.1 802.3af Compliant Ethernet Switch IP Phone 1 2 3 4 5 6 Speaker Speaker InformaCast Server Speaker (1) Template for Speaker and Screw Holes* (1) Speaker Assembly (1) Drop Ceiling Mounting Kit (3) #8 Nylon Thumb Nuts (3) #8 Fender Washers (3) 8-32 x 1 1/4” Mounting Screws (1) Drywall Mounting Kit (3) Plastic Ribbed Anchors (3) #8 Sheet Metal Screws * See the last page of this document Installation Quick Reference Singlewire-enabled VoIP Ceiling Speaker 011102*, RAL 9002, Gray White, Standard 011103, RAL 9003, Signal White, Optional *Replaces the 011065 number.

930319L Quick Reference Quick Reference 930319L © 2015, CyberData Corporation, ALL RIGHTS RESERVED Mounting Contacting CyberData *Ceiling Tile or Dry Wall VoIP V2 Speaker Assembly #8 Fender Washer (3x) #8 Nylon Thumb Nut (3x) #6 Screw (3x) Dry Wall Mounting Kit Template Plastic Ribberd Anchor (3x) Dry Wall Mounting Kit #8-32x1 1/4" (3X) Ceiling Mounting Screw *Optional Reinforcement Mount P/N: 010991A (Sold Seperately) Tools Required for Installation: • (1) Sheetrock saw or (1) Drywall cutter • (1) #2 Phillips Screwdriver or (1) #2 Phillips Screwdriver Hex Bit To mount a speaker: 1. Use the TEMPLATE on the back of this document to cut a hole in the wall or ceiling, and prepare holes for the screws. 2. Plug the Ethernet cable into the speaker assembly. The yellow light verifies the network connection. 3. For drop ceiling mounting, position the IP SPEAKER ASSEMBLY in the ceiling so that its screw holes align with those you prepared. 4. For drywall mounting, place the three PLASTIC RIBBED ANCHORS in the holes you prepared, and position the IP SPEAKER ASSEMBLY over them, aligning the screw holes in the assembly with the anchors. 5. For drop ceiling mounting*, use the three 8-32 x 1 1/4" MOUNTING SCREWS, #8 NYLON THUMB NUTS, and #8 FENDER WASHERS to secure the speaker. For drywall mounting, use the three #8 SHEET METAL SCREWS to secure the speaker. * For weak ceiling tile, CyberData offers a reinforcing mount (CyberData part number 010991A). Speaker Assembly Sales: (831) 373-2601 ext. 334 Support: 831-373-2601 ext. 333 Support Website: http://support.cyberdata.net/ RMA Department: (831) 373-2601 ext. 136 RMA Email: [email protected] RMA Status: http://support.cyberdata.net/ Warranty Information: http://support.cyberdata.net/ Corporate Headquarters CyberData Corporation 3 Justin Court Monterey, CA 93940, USA Phone: 831-373-2601 Fax: 831-373-4193 http://www.cyberdata.net/ Dimensions and Connections Connecting Power Features 9.0 [229] 3.0 [75] Dimensions are in Inches [Millimeter] AUX SPEAKER (-) AUX SPEAKER (+) LINE OUT (-) AUX POWER (+) (+12VDC @ 1A) J10 J9 AUX POWER (-) N/C N/C N/C N/C N/C N/C LINE OUT (+) CLASS II WIRING PoE Injector (Part #010867A) Non PoE Switch 802.3af switch Class "0" RTFM Switch To broadcast a device’s current IP address, press and release the RTFM switch within a five second window. To restore a device’s factory default settings, press and hold the RTFM switch for more than five seconds. Speaker Volume Network Link/Activity LED (yellow) Speaker Status LED (green) A solid light confirms that the speaker is operational.