CMA Dishmachines CMA-L-1X Owner's Manual

ˆ Dishmachine checked for concealed damage ˆ Hot water supply is 140° F (60 C) ˆ Incoming water supply line is ½” minimum ˆ Supply circuit breaker for machine is properly sized (20 amp) ˆ Service voltage and phase type are correct to machine data plate ˆ Drain hose is installed with adequate air gap ˆ Dishmachine is properly grounded ˆ Dishmachine is properly leveled ˆ Machine circuit breaker is labeled “DISHWASHER” ˆ Machine has been connected with correctly sized wire (12 gauge minimum) MODEL L-1X & L-1X16 Installation & Operatio ...

All sections of the manual address both the L-1X and the L-1X16. Separate information on each machine is only provided where differences exist between the two models. 2.1. Introduction to the L-1X and L-1X16 The L-1X and L-1X16 Dishmachines are unique in their field; they have all the features of a standard commercial size machine packed into an under-counter, standalone dishmachine. Operation of the L-1X and L-1X16 are extremely easy. After initially filling the machine (see section 3.1.3 Filling the Machine), toggling the Fill/Start switch to the “START ...

WATER CONSUMPTION PER RACK 1.7 GAL. 6.44 L PER HOUR 40.8 GAL. 154.4 L OPERATING CYCLE WASH TIME-SEC 57 57 RINSE TIME-SEC 48 48 DWELL TIME-SEC 15 15 TOTAL CYCLE 2 MIN. 2 MIN. OPERATING CAPACITY RACKS PER HOUR 24 24 WASH TANK CAPACITY 1.7 GAL. 6.44 L PUMP CAPACITY 35 GPM 132.5 LPM WATER REQUIREMENTS 140°F 60°C WATER INLET ½” — DRAIN CONNECTION 1” — CYCLE TEMPERATURES WASH-°F (Min) 140 60°C FRAME DIMENSIONS DEPTH 23 ½” 59.69 cm WIDTH 24” 60.96 cm L-1X HEIGHT 30” 76.2 cm L-1X16 HEIGHT 33 ¾” 85.73 cm L-1X MAX CLEARANCE FO ...

The L-1X and L-1X16 Operational Cycle has a total cycle time of 2 minutes (120 seconds). The Timing Diagram and the steps listed below detail the individual functions that are executed during each Operational Cycle. Seconds: 0 10 20 30 40 50 60 70 80 90 100 110 120 WASH RINSE DRAIN Instant Start Relay Cam 1 Start/Stop Cam 2 Detergent Drain/Rack Counter Cam 3 Cam 4 Flush/Fill Cam 5 Sanitizer Cam 6 Rinse Pump Motor Cam 7 Heater* Cam 8 *Heater is optional 1. With the machine powered up, toggling the START switch begins a cycle. a) Toggling the START swit ...

efficiency of chemical use (see section 4.1.1 Cam Adjustment.) 3.2.3. Proper Filling The amount the machine is automatically filled each cycle is determined by the number 4 cam. When the number 4 cam switch actuator rides down into the cam groove, the solenoid valve on the fill line is energized causing the machine to fill. Since the cam only controls the duration of the fill, varying water pressure can vary the amount the machine fills. If the water pressure at the facility where the machi ...

Replace pump motor P/N: 00416.00 Rinse pump does not run Defective timer assembly (Cam 6) Replace timer assembly* P/N: 00408.80 Defective sani/detergent primer switch Replace primer switch P/N: 03470.00 Activating detergent primer switch does not run pump Defective detergent pump motor Replace pump motor P/N: 00416.00 Defective sani/detergent primer switch Replace primer switch P/N: 03470.00 Activating sani primer switch does not run pump Defective sani pump motor Replace pump motor P/N: 00416.00 Defective rinse primer ...