Draper Premier Installation Instructions

Caution ➀ Read instructions through completely before proceeding. ➁ Follow instructions carefully. Installation contrary to instructions invalidates warranty. ➂ Screen should be accessible for complete removal should fabric become damaged or should other service be required. ➃ Screen should be installed level (using a carpenter’s level). ➄ Nothing should be fastened to screen dowel or viewing surface. ➅ Operating switch(es) packed separately in screen carton. Do not discard with packing material. ➆ Screen operates on 110-120v, 60 Hz. current. Hanging Screen General: When locating viewing surface and checking clearance for screen’s operation, remember surface is centered in case. Handle case carefully to protect finish. Regardless of mounting method, screen should be positively and securely supported so that vibration or even abusive pulling on the viewing surface will not cause case to work loose or fall. Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen. Suspended Installation: Suspend screens from holes in endcaps as shown. “S” hooks are included with screen. Chains (or cable) and turnbuckles should be provided by installer. Chains should be attached to beams or other structural members. Turnbuckles should be adjusted so screen hangs level. Wall Installation: Mount screen through holes in back of endcaps as shown. No. 12 screws for wood or aluminum are provided. However, if screen attaches to plaster, gypsum board or masonry, installer should furnish toggle bolts, molly bolts, nylon or lead anchors as required. Recessed Installation: Recess should permit access for removal of screen if necessary. Screen may be mounted as in suspended or wall installation. Optional ceiling slot kit also available; see diagram on page 2 and separate instruction sheet (included with ceiling slot kit). Electrical Connections Screen operates on 110-120v, 60 Hz. current. Junction box is located inside left endcap and cover plate is secured to endcap with two screws. Junction Copyright © 2003 Draper, Inc. Form Premier_Inst03 Printed in U.S.A. NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Operation CAUTION—Important Instructions: Shipping support brackets must be removed from each end of dowel during initial operation, before screen is operated in UP direction. After screen is installed, lower viewing surface to access screws holding brackets to dowel. Loosen hex head screw, remove bracket and retighten screw at each end of dowel. Raise and lower viewing surface several times to confirm satisfactory operation. If viewing surface does not operate properly, turn power off and check electrical connections. 110-120v Single Station Control—3-position up-off-down switch permits operation to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up. 110-120v Multiple Station Control—Switches are similar in appearance to 110-120v Single Station Control. Screen stops when switch is released and may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully up or fully down. 24v Control—Three-button up-stop-down switch(es) stop at any point desired, operate in any sequence. Factory adjusted limit switches automatically stop screen when fully up or fully down. Key Operated Switching—Two kinds of key-operated switches are optionally available with this unit. ➀ The key-operated power supply switch controls power to the screen and switches. When it is “off”, the switches will not operate screen. Key may be removed from the switch in either “on” or “off” position. ➁ A three-position key switch permits the screen to be operated directly by key. In this case, the screen’s operator must always have a key. Adjustments Screen has been factory set and should not normally require further adjustment. However, if you desire to change the “up” and “down” stopping positions, proceed as follows: CAUTION: Be sure all switches are in “off” position before adjusting limit switches. Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run too far up or too far down. Adjusting “fully up” position — “Up” stopping position may be adjusted by turning the yellow limit switch adjustment socket. The yellow socket is located on left end of screen roller and is accessible to a screwdriver/Allen wrench (4mm or 5/32"). Turning the socket counterclockwise will allow the viewing surface to retract farther into the case. Turning it clockwise will cause the surface to stop farther out of the case. One full revolution of the socket will alter the stopping position of the viewing surface by approximately 11/2". Adjusting “fully down” position — “Down” stopping position may be adjusted by turning the white limit switch adjustment socket. The white socket is located on the left end of screen roller and is accessible to a screwdriver/ Allen wrench (4mm or 5/32"). Turning the socket counterclockwise will allow the viewing surface to run farther down. Turning it clockwise will shorten viewing surface, causing it to stop in a less extended position. At no time should viewing surface be unrolled enough to expose any part of screen roller. box contains terminal strip, per wiring diagram on reverse. Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire connecting screen to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with wiring diagram supplied, and wiring should comply with national and local electrical codes. All operating switches should be “Off” before power is connected. Please Note: Instructions for adjusting Draper’s Tab-Tension System for Series/V screens are on page 2. Dowel Shipping Bracket Optional ceiling slot kit also available; see page 2 for diagram

If you encounter any difficulties installing or servicing your Premier screen, call your dealer or Draper, Inc. Spiceland, Indiana, U.S.A., (765) 987- 7999; fax (765) 987-7142; or e-mail [email protected]. Case Dimensions Page 2 of 2 Tab-Tension Adjustment Procedure for Premier ➀ Determine which side requires adjustment. ➁ Secure dowel with one hand. Caution: Do not touch or bend surface. ➂ Using Philips-head screwdriver, depress spring- loaded adjustment screw (see drawing below) and slowly turn clockwise to tighten tension, or counterclockwise to loosen tension. The screw adjusts in ¼ turn increments. Adjust only one increment (¼ turn). ➃ If problem is not corrected, leave screen in position for 24 hours to allow surface material to stretch into position. ➄ If problem still is not corrected, repeat steps 2 and 3. Dowel Adjustment Screw Tensioning Cable Wiring Diagrams 51/4" 113/16" 57/8" 1" 15/16" 7/8" dia. electrical connection hole Mounting hole 21/8" STOP Single Station Control Internal Screen Wiring White (Common) Black (Down) Red (Up) Green (Ground) Dashed wiring by electrician Control switch Single gang box by others Min. 4" x 2 1/8" x 1 7/8" deep Blue Black Red Location of key operated on-off switch if furnished To 110-120V Line Multiple Station Control Internal Screen Wiring White (Common) Black (Down) Red (Up) Green (Ground) Dashed wiring by electrician Red Red Black Blue Blue Cap off with wire nut and tape Black Red Blue Black Single gang box by others Min. 4" x 2 1/8" x 1 7/8" deep. 3 shown. More or less equally feasible. Location of key operated on-off switch if furnished To 110-120V Line Low Voltage (& Wireless) Control Wiring Diagram Control Switches 24v DC Black (DN) Red (UP) White (COM) Black (DN) Red (UP) White (COM) Black (DN) Red (UP) White (COM) STOP Black Red White White Red Brown Black Yellow Green Low Voltage Control Module Internal Screen Wiring White (Common) Red (Up) Black (Down) Green (Ground) Dashed wiring by electrician Optional Infrared Receiver Package Optional Radio Receiver Package Location of key operated on-off switch if furnished To 110-120V Line Types of Installation Appropriate hardware provided by installer. Suspended Wall Appropriate hardware provided by installer. Targa or Premier Case Back Ceiling Tile