Code Alarm CA 6551 Owner's Manual

PROFESSIONAL SERIES Owner’s Guide For Models: CA 6551 CA 6551 SST IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. Deluxe Vehicle Security and Remote Start System with 2 Way Confirming LCD Remote Control

Table of Contents Using Your Remote Control ............................................................... 3 Arming the Security System ............................................................ 3 Passive Arming Bypass ................................................................... 3 Bypassing the Shock Sensor .......................................................... 3 Hidden Alarm Function ...................................................................... 3 Disarming the Security System ........................................................ 3 Two Stage Door Unlock (optional) ................................................... 4 Activating Trunk Release (optional) ................................................ 4 Activating Optional AUX 1 (optional) ............................................... 4 Using the Progressive Car Finder Feature ...................................... 4 Using the Personal Protection Alarm ............................................... 4 Programmed Transmitter Notification .............................................. 4 Valet Mode ........................................................................................ 5 Eliminating Arm / Disarm Notification Chirps .................................... 5 Manually Overriding the Security System ....................................... 5 Car Jack Mode .................................................................................. 6 Using Your Remote Vehicle Starter ................................................. 6 Remote Starting Your Vehicle .......................................................... 6 Remote Start Shutdown ................................................................... 6 Entering Your Vehicle while it is Running via Remote Start ........... 7 Preheating or Precooling the Vehicle’s Interior ............................... 7 User Programmable Run Time / Run Time Extension ...................... 7 Using the “Quick-Stop” Feature ....................................................... 7 Operating the 2 / 3 Hour Start Up Timer Mode ................................ 8 Turbo Timer Mode (optional) ............................................................ 8 Operating the Daily Start Timer ........................................................ 9 Remote Start Safety Features ......................................................... 9 LED and Siren/Horn Indications ....................................................... 10 Additional 2-Way LCD Remote Control Functions ...................... 11 LCD Remote Control ICON’s ............................................................ 13 Transmitter Button Functions ......................................................... 14 Replacing Remote Control Batteries ............................................. 16 Warranty Information ......................................................................... 17

Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response from the vehicle. Passive Arming Bypass If passive arming is enabled on your system, while the system is disarmed, press + , the system will respond with 1 chirp and the LED will turn on. The security system will remain in this temporally bypassed state for as long as you wish. To exit passive bypass, press the or button and the system will return to normal status. Bypassing The Shock Sensor To arm the system and ignore the shock sensor press button, then within 5 seconds press + , the system will respond with 1 long chirp. NOTE: The system will only change the shock sensor setting for one arm cycle and will be defaulted back to normal operation the next time the system is armed. Hidden Alarm Function Press the button first, within 3 seconds press the button to activate the hidden alarm function. The security system will arm with “Hidden Alarm Function” in which the siren / horn will be silenced if the system is triggered. Disarming the Security System To disarm the system press the button. The parking lights will flash 1 time, indicating the system is disarmed and has unlocked the doors (if equipped and connected). NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the button to activate an audible arming response from the vehicle. If your system is set up for 2 step unlock, a third press of will activate the audible response. *Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more than 2 seconds. Using Your Remote Control

Using the Progressive Car Finder Feature Press the button to locate your vehicle. The system will sound 5 times at low volume, increasing in volume each time the button is pressed. Using the Personal Protection Alarm (Panic) Press and hold the button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s and buttons can be used to lock and unlock the door (if the option is installed). To stop the alarm, press and hold the button on the transmitter again for 3 seconds. The system will automatically stop after 30 seconds. Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors. Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the button for 3 seconds will open the vehicle’s trunk or hatch. Activating Optional AUX 1 (Optional) If this feature is enabled on your system, pressing the and buttons simultaneously will activate an optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system. Programmed Transmitter Notification As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.

Valet Mode When valet mode is activated the status LED will light solid, and all security functions will be disabled. To enter or exit valet mode simply follow the 4 steps outlined below: 1. Turn the vehicle’s ignition ON. 2. Push and hold the programming/valet button. 3. The LED will turn on solid when valet mode is active 4. Release the programming/valet button. Manually Overriding the Security System Your system can be disarmed without the use of the transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm system; 1. Open the vehicle door. The alarm will sound. 2. Turn the ignition key to the ON position. 3. Within 10 seconds, press and release the valet push button switch. The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally. Eliminating Arm / Disarm Notification Chirps System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks. 1. Turn the ignition ON then OFF. 2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.

Using Your Remote Vehicle Starter Car Jack Mode This feature must be turned on in system programming, please consult your installing dealer. Triggering Car Jack mode: While the ignition is ON and press and hold + for 2 seconds, the parking lights will flash 1 time and the system will act as follows; 1. 50 seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Car Jack mode. If Car Jack mode is not turned off at this time it will advance to the next step. 2. Following the 15 second chirps (total time now 65 seconds) the siren will go into full sound and the parking lights will start flashing. 3. 90 seconds after trigger in, addition to the siren and parking lights, the system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS STATE UNTIL THE BATTERY IS DEPLETED. OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF then On and press the valet button within 10 seconds. Remote Starting Your Vehicle To activate the remote vehicle start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running. If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2 more times to start the vehicle (a total of 3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the 3rd attempt, the system will abort the remote vehicle start process. Remote Start Shutdown Press and hold the button for 3 seconds to turn the vehicle off.

Using the “Quick-stop” Feature If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you. To engage quick stop: 1. Stop the vehicle and place the transmission in PARK. 2. With your foot off the brake pedal, press and release the button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered. 3. Remove the keys from the ignition and exit the vehicle. Press the button to lock the vehicle’s doors if desired. Note: Do not leave children or animals unattended in the vehicle when using the quick-stop feature. Entering the Vehicle while it is Running via Remote Vehicle Start 1. Unlock the vehicle’s doors. 2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL! 3. Insert the key into the ignition switch and turn to the ON or RUN position. 4. Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally. Preheating or Precooling the Vehicle’s interior Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle’s interior to your setting. User Programmable Run Time / Run Time Extension The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes. Follow the steps below to extend the vehicle’s run time. 1. The remote start must already be active. 2. Press and release the button 4 times. 3. The system will chirp to confirm that the run time has been reset.

Operating the 2 / 3 Hour Start Up Timer Mode The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, Selection between 2 or 3 hour is made in option programming. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged. To begin the 2 / 3 hour start up timer mode: 1. Turn the vehicle’s ignition ON then OFF. 2. Press and hold the valet button. 3. Press the button 4 times, the system will; a. When set for 3 Hour (default) - chirp 2 times and flash the parking lights 4 times. b. When set for 2 Hour - chirp 1 time and flash the parking lights 2 times. 4. Release the valet button. To exit the 2 / 3 hour start up timer mode: 1. Turn the vehicle’s Ignition ON. OR 1. Activate the remote vehicle start feature using the remote control. Turbo Timer This option will keep the engine running to allow the vehicle’s turbo to properly cool down before shutting the engine off. To engage the Turbo Timer feature: 1. With the vehicle running via the ignition key and your foot off of the brake pedal. 2. Engage the vehicle’s parking brake and press the and buttons simultaneously. 3. The vehicle’s parking lights will turn on to verify the Turbo Timer feature has been activated. 4. Turn the ignition key OFF, the vehicle will continue to run until the pre- programmed time has elapsed (1, 3, or 5 minutes) To disengage the turbo timer feature, press the vehicle’s brake pedal.

Remote Start Safety Features For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any of the following occur: 1. The vehicle hood is open. 2. The brake pedal is pressed prior to turning the ignition key to the ON position. 3. The engine is over-revved (tach checking only). 4. Valet mode is active. Operating the Daily Start Timer The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, pressing both the & buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process. 1. Turn the ignition ON/OFF (vehicle must be disarmed). 2. Within 10 seconds, while pressing the brake, press and release the button twice. 3. The vehicle will emit 2 chirps.

LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH... PAUSE ZONE 5 TRIGGER, IGNITION Siren/Horn Indications Chirps Function 1 DISARM 2 ARM 3 DOOR AJAR UPON ARMING 4 DISARM / TRIGGERED 5 CAR LOCATOR Parking Light Flash Indications Flashes Function 1 DISARM 2 ARM 3 DISARM / TRIGGERED 5 CAR LOCATOR ON (SOLID) REMOTE STARTED

Check Vehicle Status Press and release 2 times then press within 3 seconds, the transmitter will respond with one melody sound and display the current status of the vehicle. Display Illumination Press and hold the button for 1 second. The display will illuminate for 5 seconds. Melody / Vibration Mode To have the remote control vibrate, play a melody tone or both each time it receives a response from the vehicle press and release then press and hold for 2 seconds. Button Beeps To toggle button beeps on or off press and release then press and hold for 2 seconds. Battery Save Mode While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any incoming signals from the main unit until a button is pressed. The LCD screen will display SAVE to indicate that power save mode is ON. To enter power save mode press and hold for 5 seconds. Clear Flashing Icons and Melody Sound Press the button 3 times within 3 seconds. This will clear the melody sound and flashing icons on the LCD screen. Stopping LCD Trigger Melody To stop the alarm trigger melody if the system has been triggered WITHOUT disarming the system, press any button one time only, this will not send a command to the vehicle at this time and the alarm will continue to sound. Additional 2-Way LCD Remote Control Functions

Button Lock Press and release then press hold the for 2 seconds to toggle the button lock on or off. When the button lock is active, the remote control will beep/vibrate 2 times when a button is pressed indicating it is locked. Illumination Press and release 2 times then press and hold for 2 seconds to toggle illumination on or off. When on, the display will illuminate when it receives or sends a command. 2 Car Mode To control a second security system enter 2 car mode by pressing then press and together for 3 seconds. When the icon appears on the transmitter’s LCD screen it will control the second security system. Use the same method to exit 2 car mode and resume control of the original vehicle’s security system. NOTE: A second security system must be installed and the LCD transmitter must be learned to it before this feature will operate the additional system. Parking Meter Countdown The parking meter countdown timer has 6 preset times, to access the preset times and begin countdown press and release then press and hold for 2 seconds, each additional press of will increase the countdown time. Adjusting the Clock and Timer Settings The clock, alarm clock and programmable countdown timer are accessed through the Function Menu. Press and hold for 3 seconds to access the function menu, once you have accessed the feature menu press and release to scroll through each feature and follow the steps below to adjust the settings for each. Press and hold for 2 seconds to exit the menu. Clock Hour Press to increase or to decrease Clock Minute Press to increase or to decrease Alarm Clock Hour Press to increase or to decrease Alarm Clock Minute Press to increase or to decrease Alarm Clock ON / OFF Press to turn ON or to turn OFF Countdown Timer Hour Press to increase or to decrease Countdown Timer Minute Press to increase or to decrease Countdown Timer ON / OFF Press to turn ON or to turn OFF

LCD Remote Control ICON’s LOCK UNLOCK SYSTEM ARMED VALET MODE TRANSMITTING TRUNK TRIGGER DOOR TRIGGER FULL SHOCK TRIGGER IGNITION ON/TRIGGER ENGINE RUNNING 2 CAR MODE BATTERY INDICATOR BATTERY SAVE MODE VIBRATE/SILENT MODE HOOD TRIGGER SYSTEM TRIGGER TIME COUNT DOWN MELODY MODE TIME DISPLAY TIMER START MODES ALARM CLOCK AUX 1 OUTPUT

Transmitter Button Functions 1 Way Transmitter Lock Unlock Car Find / Panic Start Operation Method Lock X Press and Release Unlock X Press and Release 2 Step Unlock X Press and Release 2 times Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shutdown X Push and Hold (3 Sec) Run Time Extention X Press and Release 4 times. AUX 1 X X Push and Hold (3 Sec) Shock Bypass X X Press and Release Lock then Press Lock + Car Find Hidden Alarm X X Press and Release Car Fnd then Press Lock Passive Arming Bypass X X Press and Release Turbo Timer X X Press Unlock + Start 2 / 3 Hour Start X Ignition ON/OFF, Press and Hold Valet Button, Press Start 4 times Daily Start Timer X X Press Lock + Start

2 Way Transmitter Lock Unlock Car Find / Panic Start Function Operation Method Lock X Press and Release Unlock X Press and Release 2 Step Unlock X Press and Release 2 times Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shutdown X Push and Hold (3 Sec) Run Time Extention X Press and Release 4 times. AUX 1 X X Push and Hold (3 Sec) Shock Bypass X X Press and Release Lock then Press Lock + Car Find Hidden Alarm X X Press and Release Car Fnd then Press Lock Passive Arming Bypass X X Press and Release Turbo Timer X X Press Unlock + Start 2 / 3 Hour Start X Ignition ON/OFF, Press and Hold Valet Button, Press Start 4 times Daily Start Timer X X Press Lock + Start Menu X Press and Hold

Replacing Remote Control Batteries 1 Way 4 Button Remote Control - CA6551 / CA6551SST The batteries inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Remove 3 screws and disassemble the halves of the remote control. 2. Remove the old batteries, observing the +/- symbols on the batteries and replace with new batteries. 3. Reassemble the halves of the remote control and install the 3 screws. 4. Test operation of the remote control. NOTE: The CA6551 uses 2 CR2016 batteries and the CA6551SST uses 1 CR2032. 2 Way LCD Remote Control - CA6551 The CR2450 battery inside the 2-way LCD remote control should last approximately 6 months under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the BATTERY icon on the LCD remote control will show. 1. Gently slide the battery cover off of the remote control. 2. Remove the old CR2450 battery, observing the +/- symbols on the battery, and replace with a new CR2450 battery. 3. Gently slide the battery cover on to the back of the remote control. 4. Test operation of the remote control. 2 Way LCD Remote Control - CA6551SST The battery inside the 2 way LCD remote control is rechargeable, use the supplied battery charger to charge the battery until the battery icon on the LCD screen shows 3 bars indicating charging is complete. It is recommended that the battery be fully charged before normal use.

Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI- NALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts directly related to repairs of the defect(s). Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser for a period of one (1) year from the date of purchase of the Product. CODE accessories, sold separately, are covered by the applicable warranty accompa- nying the accessory. This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed from the vehicle in which it was originally installed; or (2) the vehicle in which the Product was originally installed is transferred to another party. This warranty does not apply to any product damaged by accident, physical or electrical abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other natural acts. In order for the Product to be repaired or replaced under the terms of this warranty, the defective Product must be returned to an authorized CODE dealer and accompanied by a copy of the retail sales receipt. The date of purchase and year, make and model of the vehicle in which the Product was originally installed must be clearly indicated on the sales receipt. This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER- CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR- RANTY, EXPRESS OR IMPLIED, WHATSOEVER. CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION LABOR. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

for models: CA 6151 CA 6551 CA 6551 SST 2010 Audiovox Electronics Corporation. All rights reserved. 4280302

Before You Begin 4 Wire Connection Guide 5 4 Pin Main Harness , 7 6 Pin Start Harness 8 6 Pin Output Harness 10 8 Pin Input Harness 11 4 Pin Alternate Output Harness 14 3 Pin Door Lock Output Harness 16 Additional Ports 20 Antenna / LED / Programming Port 20 DBI Port 20 Tracking Port 20 Set Up & Programming 21 Transmitter Programming 21 Manual Feature Programming 21 Programming Feature Banks 22 Tach Programming 23 Smart Tachless Mode 24 Adjusting the Shock Sensor 24 Testing the Shock Sensor 24 Chirp Delete - User Accessible 24 Dome Light Delay / Theater Dimming 25 2010 Audiovox Electronics Corporation. All rights reserved.

30 Security Trigger Zones 31 Remote Start Shutdown Diagnostics 31 System Layout 32 2010 Audiovox Electronics Corporation. All rights reserved. 3

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Use grommets when routing wires through metal surfaces Tape or loom wires under hood for protection and appearance Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE PROBEIl as these can set off air bags or damage vehicle computers. . . •.... Technical Support (800) 421-3209 or go to http://techservices.codesystems.com 4 2010 Audiovox Electronics Corporation. All rights reserved.

z WHITE/RED PARKING LIGHT INPUT « WHITE PARKING LIGHT OUTPUT ~ z BLACK GROUND a.. ~ SIREN OUTPUT ( + ) BROWN 6 Pin Start Harness PURPLE STARTER OUTPUT - MOTOR SIDE l- RED BATTERY 12V (+) c::: ~ ORANGE ACCESSORY 1 ( + ) (/) z PINKIWHITE IGNITION 2 (+) a.. <0 RED BATTERY 12V (+) PINK IGNITION 1 ( + ) 6 Pin Output Harness l- => a..l- =>o za: <0 BROWN/BLACK BLUE/BLACK VIOLET/BLACK REDIWHITE LT GREEN/BLACK ORANGE HORN OUTPUT ( - ) IGNITION 3 ( - ) AUX 1 ( - ) TRUNK RELEASE OUTPUT ( - ) FACTORY DISARM / PULSE BEFORE START (-) GROUND WHEN ARMED OUTPUT ( - ) 2010 Audiovox Electronics Corporation. All rights reserved. 5

BLUEIWHITE INSTANT TRIGGER INPUT ( - ) GREEN DOOR TRIGGER INPUT ( - ) t- PURPLE DOOR TRIGGER INPUT ( + ) ~ a.. WHITE/BLUE EXTRENALSTARTINPUT(-) z z GRAY HOOD PIN INPUT ( - ) a.. co BLACKIWHITE NEUTRALSAFETYINPUT(-) BROWN/RED BRAKE INPUT ( + ) PURPLEIWHITE TACH INPUT 4 Pin Alternate Output Harness LT GREEN/BLACK LT BLUE GREENMIHITE BLACKIYELLOW FACTORY DISARM / PULSE BEFORE START ( - ) PULSE AFTER START ( - ) FACTORY ARM / PULSE AFTER SHUTDOWN (-) PULSE DURING CRANK (-) 3 Pin Lock Output Harness z~ -u 0.. 0 ("').....J BLUE OPEN GREEN UNLOCK (-) LOCK ( - ) 6 2010 Audiovox Electronics Corporation. All rights reserved.

WHITE/RED WHITE PARKING LIGHT INPUT PARKING LIGHT OUTPUT Locate the parking light output wire at the vehicle's light switch. Verification: This 'vvire registers positive voltage when the parking iights are turned on. Positive switching Parking Lights: Connect the WHITE/RED wire to a 15 Amp max fused battery source. Connect the WHITE wire to the parking light output wire. Negative switching Parking Lights: Connect the WHITE/RED wire to a good chassis ground. Connect the WHITE wire to the parking light output wire. 3 BLACK GROUND Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver's side kick panel area. NOTE: Do not ground the BLACK wire with any other vehicle components. 4 BROWN SIREN OUTPUT ( + ) Locate a suitable mounting location in the engine compartment for the siren, away from moving parts. With the bell of the siren aiming downwards, secure the siren in place using self tapping screws, being careful not do drill into any hoses, wiring or components. Connect the BLACK siren wire to a chassis ground using a ring terminal and self tapping screw (not supplied). Route the BROWN siren output wire from the control module through the firewall and connect to the RED wire on the siren. NOTE: Be sure to loom the siren Wires, and seal the grommet. 2010 Audiovox Electronics Corporation. All rights reserved. 7

PURPLE STARTER OUTPUT ( + ) Locate the vehicle starter wire. Verification: This wire registers voltage only when the key is turned to the START position. Cut the vehicle's starter wire in half when installing the starter kill relay. Verification after starter wire is cut: KEY SIDE of starter wire registers voltage when the key is turned to the START position. MOTOR SIDE of starter wire registers no voltage. Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE of the vehicle starter wire when installing the starter kill relay. 2 RED BATTERY 12V ( + ) Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch. Verification: This wire will register ( + ) voltage in all positions of the ignition switch. Connect the RED wire to the constant 12 Volt battery wire. NOTE: Remove all fuses until all connections are made. 3 ORANGE ACCESSORY 1 (+) 8 Locate the vehicle's accessory wire at the ignition switch. Verification: This wire registers voltage when the key is turned to ACC (Accessory) and the ON (or RUN) position. The voltage drops out when the key is turned to the START (or CRANK) position. Connect the ORANGE wire to the vehicle's accessory wire. 2010 Audiovox Electronics Corporation. All rights reserved.

Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped). Verification: This wire registers voltage when the key is turned to the ON (or RUN) position, but not the ACC (Accessory) position. The voltage does not drop out when the key is turned to the START (or CRANK) position. Connect the PINKIWHITE wire to the vehicle's ignition 2 wire. Programmable output: IGN, ACC, Start. 5 PINK IGNITION 1 ( + ) Locate the vehicle's ignition wire at the Ignition switch. Verification: This wire registers voltage when the key is turned to the ON (or RUN) position. The voltage does not drop out when the key is turned to the START (or CRANK) position. Connect the PINK wire to the vehicle's Ignition wire. This wire is also used for Ignition 1 Output. 6 RED BATTERY 12V ( + ) Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch. Verification: This wire will register ( + ) voltage in all positions of the ignition switch. Connect the RED wire to the constant 12 Volt battery wire. NOTE: Remove all fuses until all connections are made. 2010 Audiovox Electronics Corporation. All rights reserved. 9

1 BROWN/BLACK HORN OUTPUT ( - ) Locate the vehicle's horn wire. Verification: This wire will register at positive voltage and register ground when the horn switch is pressed. Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current output, 500mA. 2 BLUE/BLACK IGNITION 3/ ACTIVE OUTPUT ( - ) The Active OutpuVlgnition 3 output wire provides a ground output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown. The Ignition 3 output wire can be used for several functions listed below. If this wire will be used for multiple application's a 1 amp diode is required in-line with the stripe facing the control module. Factory transponder (coded key) bypass. General Motors VATS bypass, see the following diagram. Use an SPOT relay (not supplied). Ignition 3 output, see the following diagram. Use an SPOT relay (not supplied). Accessory 2/3 output, see the following diagram. Use an SPOT relay (not supplied). GM VATS BLUE/BLACK ActlveOutput Wire 2010 Audiovox Electronics Corporation. All rights reserved. 10 Jump To PINK Ignition Output Wire From Control Module Ignition 3 BLUE/BLACK Active Output Wire Accessory 2/3 Jump To ORANGE Accessory Output Wire From Contro! Module BLUEiSLACK ActIVe Output Wire

optional accessories (i.e. Power Window/Sunroof, etc.). To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing. 4 REDIWHITE TRUNK RELEASE OUTPUT ( - ) Locate the vehicle's trunk release wire at the trunk release switch. Verification: This wire will register either positive voltage or ground when the trunk release is activated. This is a low current output, SOOmA. 5 LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - ) This wire will supply a ( - ) SOOmA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door. Verification: This wire registers ground if the key is turned to the unlock position in the driver's door cylinder. Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire. 6 ORANGE GROUND WHEN ARMED OUTPUT ( - ) This wire will have a continuous ( - ) SOOmA output when the system is Armed. This wire is typically used for controlling window modules or additional sensors. 8 Pin Input Harness 1 BLUE/WHITE INSTANT TRIGGER INPUT ( - ) This wire is a GROUND input for an external sensor or secondary pin switch. Verification: This wire when connected will trigger the security system. 2010 Audlovox Electronics Corporation. All rights reserved. 11

Locate the vehicle's dome light or door pin switch wire. Verification: This wire will register ground (NEG) when the door is opened and the interior light is on. This wire will register positive voltage when the door is closed and the interior light is off. Connect the GREEN wire to the vehicle's negative door input wire(s). NOTE: Certain vehicles may require multiple connections. Refer to vehicle application gUide. 3 PURPLE DOOR TRIGGER INPUT ( + ) Locate the vehicle's dome light or door pin switch wire. Verification: This wire will register positive voltage (PaS) when the door is opened and the interior light is on. This wire will register ground or "0" Volts when the door is closed and the interior light is off. Connect the PURPLE wire to the vehicle's positive door input wire(s). NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide. 4 WHITE/BLUE EXTERNAL START INPUT ( - ) This wire will activate the Remote Start function when a GROUND pulse is applied to it from an external device. 5 GRAY HOOD PIN INPUT ( - ) 12 Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start. Verification: This wire when connected will register ground when the vehicle's hood is opened. Connect the GRAY wire to the hood pin. NOTE: Be sure to loom the wire, and seal the grommet. 2010 Audiovox Electronics Corporation. All rights reserved.

Verification: This wire registers ( - ) voltage when the vehicle's gear selector is in park or neutral. Connect the BLACK/WHITE neutral safety input wire to the neutral safety wire of the vehicle or an optional toggle switch. The remote start feature will not operate unless this input is supplied with a ground source. 7 BROWN/RED BRAKE INPUT ( + ) Locate the vehicle's brake light wire at the brake pedal mounted switch. Verification: This wire registers positive voltage when the brake pedal is pressed. Connect the BROWN/RED wire to the vehicle's brake light wire. 8 PURPLElWHITE TACH INPUT Locate the vehicle's ignition coil or fuel injector in the engine compartment. Verification: Test using the following procedure: 1. Set voltmeter to AC VOLTS. 2. Attach positive lead of a volt meter to a constant 12 volt source. 3. Attach negative lead of a volt meter to the wire to be tested. 4. Start the engine. 5. Have someone press on the gas pedal slightly as you monitor the meter. If connected to the correct wire, the voltage reading will increase as the engine's RPM increases. Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil or fuel injector. 2010 Audlovox Electronics Corporation. All rights reserved. 13

1 LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - ) This wire will supply a ( - ) 500mA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door. Verification: This wire registers ground if the key is turned to the unlock position in the driver's door cylinder. Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire. 2 LT BLUE PULSE AFTER START ( - ) This wire will supply a ( - ) 500mA pulse both upon arming the system and upon successful completion of the remote start activation sequence and is typically used to re-Iock the vehicle's doors upon remote start if necessary. 3 GREENlWHITE FACTORY ARM / PULSE AFTER SHUTDOWN (-) 14 This wire will supply a ( - ) 500mA pulse after the remote start shuts down. This is typically used to re-Iock the vehicle's doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle's accessories from remaining on after remote start shutdown. 2010 Audiovox Electronics Corporation. All rights reserved.

Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped) Verification: This wire registers voltage only in the start (crank) position of the ignition switch. Connect the BLACK/YELLOW wire as shown in the diagram below. Use an SPOT relay (not supplied). Fused +12 Volt Battery SOUr( e Jump To PURPLE S tarter Output 1---+11 Wire From The Control Module 2010 Audiovox Electronics Corporation. All rights reserved. 15

1 3 BLUE GREEN UNLOCK ( - ) LOCK ( - ) The door lock / unlock outputs are designed to control several different types of systems which may require additional parts. Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the following diagrams. Negative SWitching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle's lock / unlock switch. Verification: These wires will register ground when the Lock and Unlock switches are activated. Connect the GREEN and BLUE wires shown in the diagram below. Negative Locks: GREEN 1-) Lock Output Vehicle Door Lock Control Relays 16 BLUE (-) Unlock Output 2010 Audiovox Electronics Corporation. All rights reserved.

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle's lock / unlock switch. Verification: These wires will register positive voltage when the Lock and Unlock switches are activated. Connect the GREEN and BLUE wires shown in the diagram below. Positive Locks: 873 30 GREEN (-) Lock Output Vehicle Door Lock Cootrol Relays 86 BLUE (-) Unlock Output Reverse Polarity Locks (5-Wire Door locks) All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle's lock / unlock switch. Verification: These wires will rest at ground and register positive voltage when the Lock and Unlock switches are activated. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPOT relays (not supplied). Reverse Polarity Locks: BLUE (-j Unlock Outp'- GREEN (-j Lock Output :e-----I~ To Door Lock Motor ......----t~ To Door Lock Molor Cut Cut 2010 Audiovox Electronics Corporation. All rights reserved. 17

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle's lock / unlock switch. Verification: This wire will show variable ground when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPOT relays (not supplied). Multiplex Locks: .------1 Ground 1-----, 87 GREEN (-) Lock OUlptJl ~--H Positive Multiplexed Locks H-- 85--l BLUE (-) Unlock OUlpul 18 All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle's lock / unlock switch. Verification: This wire will show variable positive voltage when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPOT relays (not supplied). M'ultiplex Locks: 87 87 - - I GREEN (-) Lock Output I • 87• . I Fused .12 Volt I • 87• • I BLUE (_) Unlock Output 86 I ~ I 85 I Battery Source I 86 I J • 65 30 30 r-- ~ ~ ~ • • ~ I Vahlcle Doo' Lock I I Control Relays l.Wook--- 2010 Audiovox Electronics Corporation. All rights reserved.

After installing aftermarket actuators, (not supplied). Connect the GREEN and BLUE wires shown in the diagram below using (2) SPDT relays (not supplied). 87 ,.----i__---t Fused +12 Volt Battery Source 86 ,,------1.....----1 Fused +12 Volt Battery Source GREEN (.j Lock Output 86 BLUE (oj Unlock Output 2010 Audlovox Electronics Corporation. All rights reserved. 19

Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield that will not block the driver's vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window fiim, as this will effect system range. Route the antenna! receiver cable to the control module and plug into the antenna port. Data Bus Interface Port This 4 pin port is used for Flashlogic Door Lock and Transponder Databus Interfaces to communicate with the vehicle's Databus. When using the OBI port to control the Flashlogic Door Lock and Transponder Interface modules the following options may be available. Please refer to the 020 (Data to Data) function list available per vehicle on the tech service web site. Tach Input Brake Safety Shut Down Door Trigger Trunk/Hatch Open Door Lock Control Passlock / Passkey Interface (GM Only) Dome Light Supervision Transponder Interface Activation Factory Alarm Arm / Disarm Diesel Glow Plug Input Manual Arm / Disarm Inputs (factory keyless controls system) Tracking Port This 4 pin port is used for Code Alarm Car Link or Vehicle Tracking accessories. 2010 Audiovox Electronics Corporation. All rights reserved.

Transmitter Programming - Feature Bank 1 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Press 1 button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. 6. Pressing the override button at anytime during programming will advance to the next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity. NOTE: This system has 1 button programming which programs all channels of the system. NOTE: The system will hold up to 4 transmitters in memory, programming a 5th transmitter will erase the oldest transmitter in memory. NOTE: This system has PTN - Programmed Transmitter Notification. Each time the ignition is turned ON, the LED will flash the number of transmitters programmed to the system. Transmitter programming for 2 Car Mode *2 way system only: 1. Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in the owners manual for 2 car operation) 2. Follow the steps above for transmitter programming. NOTE: 2 car mode requires an additional security system installed in a second vehicle. Manual Feature Programming - Feature Bank 2 - 4 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Use the valet/override button to advance through each option bank. For feature programming advance to Feature Bank 2, 3 or 4, which is (4) four, (5) five, and (6) six chirps. 5. Use the transmitter () button to scroll through the selections in each feature bank, the system will chirp to match the feature number. 6. Press the transmitter i button to change the desired feature. The LED will flash indicating the changed feature. 2010 Audiovox Electronics Corporation. All rights reserved. 21

feature banks will default all features and return you to feature bank 2 - 4 chirps. NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF. Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming. Feature Bank 2 • 4 Chirps 1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash Security Control C.'. '. .' .0," 1 SIlent ChoiCe ON OFF . .... '" . . .' 2 Passive Locks Active Passive .' ,,--" '.' .. .' . " 3. fI~iveArmlng ActIve ., Passlv8 ,';, i : 4 Siren / Horn - Arm/Disarm Chirps Siren / Horn Siren Horn " ,. .' .,. '" 5 .Securjty' ON .... OFF . .;- . , . " " 6 Hi Jack OFF ON Feature Bank 3 • 5 Chirps Output Control 1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 2 Factory Disarm Factory Disarm . , OFF 2nd Unlock Start Status .". . .... '. . :.:-.:; I',· .. ". . 4 Horn Output Timing ":, ' 16mS 10mS '...... ::.. .' ,~ > 30mS .'.. :: 40mS . "'. .... 50mS . . - ". :'.. '. ','. ..'. ..',: 22 6 AUX 1 Push and Hold Latched Latched until Dome Light IGN ON Output 2010 Audiovox Electronics Corporation. All rights reserved.

1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash Remote Start Control 1 RF.Staft Chirp Ott OFF 2 Run Time 15 Minutes 5 Minutes 10 Minutes 20 Minutes 45 Minutes 60 Minutes 3 RunnIog Ught8 ... Steady Ft-.l1iog .' Tachless Hybrid (Crank 4 Tach Mode Tach (Crank Average Average I NO DBIPort I Voltage) Voltage) 5 VoItag8 .Level "1Qh low 6 Crank Time 1.0 Seconds 0.8 Seconds 1.5 Seconds 2.0 Seconds 4.0 Seconds , -- .... 7 Crank'Ave@ging I Crank TIme AWIIIQIng Pi'esetTime 8 Gas I Diesel Gas 10 Second 15 Second 20 Second 45 Second Delay Delay Delay Delay 9 Single"Double Pulse Start DoublePfHS SIng!e'Pre$s 10 IGN 2 Output Ignition 2 Accessory Start I Crank 11 2 or 3 Hour Start 3 Hour 2 Hour 12 Turbo Timer OFF 1 Minute 3 Minute 5 Minute Tach Programming The unit will not operate unless tach is programmed or tachless option is turned ON. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and reengage the starter motor. The Remote Start unit will learn the tach rate of most vehicle's single coil, mUltiple coil packs, or single injector. To learn tach: 1. Turn the ignition key to the ON position. 2. Press and release the valet/override button 3 times. 3. Immediately turn the ignition key OFF. 4. Press and hold the valet/override button, then start the vehicle using the key. 5. When the unit senses the tach signal, the parking lights will begin to flash. 6. Allow the vehicle to settle to a normal idle speed. 7. Release the valet/program push-button switch. The parking lights will turn on for 2 seconds indicating that the learned tach signal is stored and the unit has exited tach learn mode. 2010 Audlovox Electronics Corporation. All rights reserved. 23

poor tach source, the parking lights will not flash. To correct this situation, locate and connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach learn routine. Smart Tachless Mode Smart Tachless Mode is available only if a tach signal has never been learned to the system and when activated will automatically change the Tach Mode feature in option programming to Tachless without the need to enter the feature programming mode. 1. Activate the remote start. The parking lights should begin flashing 7 times indicating no tach signal has been learned. 2. Within the 7 flash time period, press and hold the () button. 3. The system will chirp 1 time indicating the system is now in tachless mode. Adjusting the Shock Sensor 1. Increase sensitivity by turning the adjustment dial clockwise. 2. Decrease sensitivity by turning the adjustment dial counter clockwise. Testing the Shock Sensor Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike the vehicles bumper. Chirp Delete - User Accessible System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks. 1. Turn the ignition ON then OFF. 2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF. 2010 Audiovox Electronics Corporation. All rights reserved.

The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will 'learn' the timing of the dome light delay and add 2 seconds before arming. 1. Close all doors with ignition off. 2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK, UNLOCK, LOCK. The LED will light solid to indicate the system has entered DOME DELAY LEARN MODE. 3. Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the learning mode. 4. The LED will begin to flash indicating the system has exited the learning mode and is now armed. Feature Descriptions Feature Bank 2 - Security 1 - Silent Choice: Controls the normal arm/disarm chirps of the security system. ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons. OFF - normal arm/disarm chirps upon the first press of lock/unlock. 2 - Passive Locks: Determines manual or automatic locking of the vehicle's doors. Active - Requires use of the transmitter to lock the vehicle's doors. Passive - Automatically locks the vehicle's doors 1 minute after the last door is closed 3 - Passive Arming: Determines manual or automatic locking of the vehicle's doors. Active - Requires use of the transmitter to arm the security system. Passive - Automatically arms the security system 1 minute after the last door is closed 2010 Audiovox Electronics Corporation. All rights reserved. 25

arm/disarm chirps. This feature does not effect the triggered state of the security system and during a triggered cycle, both the siren and horn outputs will activate respectively. 5 - Security: Controls security functionality - ON / OFF. ON - Full security functionality. OFF - The security system does not trigger. Panic, Remote Start and all other convenience features opeiate as normaL 6 - Hi Jack: Controls hi jack mode - ON / OFF. OFF - Standard security system operation. ON - Enables Hi Jack mode functionality as described in the owners manual Feature Bank 3 - Output Control 1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock output wires. 1 Second - Single 1 second lock pUlse, single 1 second unlock pulse. 3.5 Seconds - Single 3.5 second lock pUlse, single 3.5 second unlock pulse. 1 Second Lock, Double Pulse Unlock - Single 1 second lock pUlse, double 1 second unlock pulse. 30 Second Lock, Double Pulse Unlock - Single 30 second lock pUlse, double 1 second unlock pulse. Double Pulse Lock, 1 Second Unlock - Double 1 second lock pUlse, single 1 second unlock pulse. 2 - Factory Disarm: Controls the timing of the LT. GREEN/BLACK factory disarm wire on the 6 pin output harness only and does not change the output of the factory disarm wire on the 4 pin alternate output harness. Factory Disarm - Single 1 second pulse with unlock and remote start activation. 2nd Unlock - Same ouput as unlock with 2nd press of unlock only. Start Status - Continuous ( - ) output during the remote start cycle. 2010 Audiovox Electronics Corporation. All rights reserved.

ON or OFF. OFF - Door locks not activated by ignition. Lock and Unlock - Doors lock when ignition is turned on and unlock when ignition is turned off. Lock Only - Doors lock when ignition is turned on. Unlock Only - Doors unlock when ignition is turned off. 4 - Horn Output Timing: Control the minimum horn pulse time in milli seconds, some vehicle will require a longer pulse to activate the factory horn. 16mS 10mS 30mS 40mS 50mS 5 - Real Panic: Controls the panic out when triggered from the transmitter. ON - Randomized horn honks when panic is triggered. OFF - Standard pattern horn honks when panic is triggered. 6 - AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing. Push and Hold - Output is continuously active until transmitter button is released. Latched - Output stays active until button is pressed again. Latched until IGN ON - Output stays active until the ignition is turned on. Dome Light Output - Output is used for illuminated entry and is not controlled by the AUX 1 function of the transmitter. Feature Bank 4 - Remote Start Control 1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or OFF. 2 - Run Time: Controls the time in minutes that the vehicle will stay running under control of the remote start until the system times out. The system may also be shut down at any time by use of the transmitter or system shutdowns. 3 - Running Lights: Controls the WHITE parking light output wire during remote start. Steady - Parking lights constant during the remote start cycle. Flashing - Parking lights flash at a slow pace during the remote start cycle. 2010 Audiovox Electronics Corporation. All rights reserved. 27

remote start. Tach - Hard wired directly to the tach wire of the vehicle to monitor AC voltage. Tachless (Crank Average/Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change in voltage after remote start. Hybrid (Crank Average / No Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key. OBI Port - Monitors the vehicle's tach rate through an interface module connected to the OBI port. 5 - Voltage Level: The voltage variance for remote start when set to tachless. (see tach mode) HIGH - The variance in battery voltage from before the remote start is activated to after the engine is running must be greater than 0.5 volts. LOW - The variance in battery voltage from before the remote start is activated to after the engine is running may be less than 0.5 volts. 6 - Crank Time: Preset output times for the PURPLE starter wire. 7 - Crank Average I Crank Time: The length of time in which the remote start will crank the vehicle's starter. Crank Average - Determines crank time by averaging the last 8 times the vehicle was started with the key. Preset Time - Preset starter output time. (see crank time) 8 - Gas I Diesel: Selects engine type and delay time for the starter output wire during remote start activation. Gas - Gasoline engine, no delay for the starter output wire. 10 Second Delay - Diesel engine, delays the starter output wire for 10 seconds after the ignition has been powered up by the remote start. 15 Second Delay - Diesel engine, delays the starter output wire for 15 seconds after the ignition has been powered up by the remote start. 20 Second Delay - Diesel engine, delays the starter output wire for 20 seconds after the ignition has been powered up by the remote start. 45 Second Delay - Diesel engine, delays the starter output wire for 45 seconds after the ignition has been powered up by the remote start. 2010 Audiovox Electronics Corporation. All rights reserved.

a single or double press from the transmitter. 10 - IGN 2 Output: Programmable high current output. Ignition 2 - Ignition output during remote start. Accessory - Accessory output during remote start. Start / Crank - Crank output during remote start. 11 - 2 or 3 Hour Start: When activated, the remote start will activate and run for the programmed time and shut down every 2 or 3 hours. 12 - Turbo Timer: When activated, the vehicle will run for the programmed time. OFF 1 Minute 3 Minutes 5 Minutes 2010 Audiovox Electronics Corporation. All rights reserved. 29

lW~ Lock Unlock Car Find! Start Op_on_od Transmitter Panic Lock X Press IIld Rele.,e Unlock Press and Release 2 StIp UnlOCk X PreSs and Reiease 211m"S Trunk X Push and HOldl3 Sec) Car"'" X press and Release Panic Push ana Hold (3 Sec) R...otestart .' X Prilss and Rl!le8!Se(t or 2Umes dipendtlgoo SeleciZl,dpUOIl) Remote Stort PuSh ana Hold 13 Sec) Shutdown Run Til... X , Press and Releate 411m.~. 1- AUX 1 Push ana Hold (3 SeC) ShOCkBypI" J( X .' press andl<.eielse Lotk ltIen ",en LOCk+Car Find Hidden Alarm Press and Release Car Fnd then Press Lock ,.••Ift A,..lng X X " Prets and Release IllYpass Turl>oTlmer X Press Unlock + Start 12/3 HourSwt X IgOtaon ONIOFF, Preu and Hold Val« ButlQn, Press'Stllt4 times Daily Start Timer X Press Lock + Start * 2 Way Transmitter - CA 6550 Only PiessritlOid i1:stl!t4Iine, Press and Release PUSh and Holdi3 Sec) PUSh ana Hold (3 Sec) Push and Hold i3 Sec) PUSh ana Hold (3 Sec) Press Unlock + Start Press and Release Car Fnd then Press Lock Press Lock + Start . ,. P~~s and.Rele~ .....•..• X I· X X X X Stolt Funchon Operltlon Method : 2Way Lock Unlock Car Find! Transmitter Panic LoCk X I Unlock X 2lt1punl.ek X Trunk X CarPI,"*, X panic X ROIlIf,teSQrt " " Remote Start Shutdown RunTIlII. E_ '. AUX 1 X , ShoCkSypU. X ,.. '.' Hidden Alarm X X "a"lvtI~1nI '.. 119.1.." X X Turbo Timer X ~ /3 HOIIrttllrt , Oally Start Timer X Mlnu ". 30 2010 Audiovox Electronics Corporation. All rights reserved.

If the security system has been triggered the LED will flash one of the patterns below indicating the zone. LED FLASHES 2 Flashes 3 Flashes 4 Flashes 5 Flashes TRIGGER ZONE Hood / Trunk Input Door Input Shock Sensor Ignition Input Remote Start Shutdown Diagnostics If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input. To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the ... button. LED FLASHES 3 Flashes 4 Flashes 7 Flashes SHUTDOWN ZONE Hood Input Brake Input Neutral Safety Input Remote Start Valet Mode Tach not learned / Crank Average not learned 2010 Audiovox Electronics Corporation. All rights reserved. 31

Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is sUbject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2010 Audiovox Electronics Corporation. All rights reserved.

CONTROLLED CAR STARTER BEFORE SERVICING THIS VEHICLE, REMOVE THE MAIN POWER FUSE (RED WIRE) TO THE CAR STARTER OR DISCONNECT THE VEHICLE BATTERY. LBL0675

quality and reliability of all our electronic products, but if you ever need service or have a question, our customer service staff stands ready to help. Contact us at www.Code-Alarm.com PRODUCT PROTECTION: In case of an insurance loss such as fire, flood or theft, your registration will serve as proof of purchase. PURCHASE REGISTRATION: Registering On-Line will allow us to contact you in the unlikely event a safety notification is required under the Federal Con- sumer Safety Act. 1026350

.CODE-AlARM.COM Click On Product Registration and Fill Out the Brief Questionnaire

~ _ MAXIMUM INSURANCE DISCOUNT AUTHORIZATION Dear Insurance Agent, The installation of my Code-Alarm automatic (passive) arming security sys1em in the vehicle indicated below qualifies me for the maximum discount mandated by law in some states and by insurance company option in others. This vehicle security system automatically arms itself after the doors are closed and includes at least one engine disabling relay to prevent the engine from being started. InsuredSignature:~~~~~~~~~~~~~~~~~~~~~~~~Na~e(~eaeprinQ:~~~~~~~~~~~~~~~~ Street Address: Insurance Co~pany:~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Policy#: ~ Vehicle Year/Make/Model: _ Vehicle Identification #: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~- The signature below certifies that ~y Code-Alar~ auto~otive security syste~ was installed on ~ ~ (date) _ Installer Signature: ~ _ Co~pany: ~ _ Address: ~ Telephone: ~ _ PLEASE COMPLETE AND MAIL TO YOUR INSURANCE COMPANY 102667

Should YOUR private passenger vehicle in which the CODE-ALARM ANTI-THEFT SYSTEM is originally installed by an authorized dealer and while the system is operational and activated be stolen and not recovered or if stolen and recovered be deemed a total loss for theft insurance purposes. then subject to the following conditions. YOU will be refunded the comprehensive auto insurance deductible on your existing insurance not to exceed $2.500.00. This Limited Warranty is effective for thefts occurring within one (I) year from the original date ofpurchase providing that: (A) the attached registration form has been completed in full and received by the CODE-ALARM Program Administrator at the address shown below with postmark that is within five (5) business days from the original date of purchase; (8) YOU properly and completely identify the vehicle in which the CODE-ALARM ANTI-THEFT SYSTEM has been installed; (C) YOUR vehicle is registered within the United States of America or Canada; (D) the theft of YOUR vehicle occurs within the United States of America or Canada; (E) YOU file a complete theft report with the police or other law enforcement agency having jurisdiction at the location of the theft; (F) YOU have comprehensive or theft insurance in force on the vehicle at the time of the theft and YOU have filed a claim for the theft of the vehicle with YOUR insurance carrier; and (G) the theft claim with YOUR insurance carrier is settled and final payment from them has been received. This Limited Warranty applied solely to passenger vehicles. motor homes. and light duty trucks or vans not exceeding 13.500 GVW. It does not apply to any vehicle used in a business. for Livery or offered for hire. This Limited Warranty applies only to the vehicle as identified on the attached registration form. In order to make a claim under the Limited Warranty. YOU are to provide the CODE-ALARM Program Administrator with the following information and materials: • Proof of purchase including the purchase date. YOU ARE URGED TO SAVE YOUR ORIGINAL RECEIPT • A certified or notarized complete copy of the police report filed by YOU • A copy of the original declaration sheet from the insurance policy in force at the time of the system purchase. This declaration sheet must clearly show the amount of the deductible applicable to theft losses • A copy of the insurance company settlement check and any related documentation CONTINUED ON REVERSE IADV· c THIS CARD MUST BE POSTMARKED WITHIN THIRfY(30)BUSINESS DAYS OF THE PURCHASE OF YOUR CODE-ALARM ANTI-THEFT SYSTEM. ORIGINAL PURCHASE RECEIPT MUST BE RETAINED AND SUBMITTED WITH ANY CLAIMFILED HEREUNDER CONSUMER REGISTRATION CARD Code-Alann Anti-Theft System Purchased Purchase Dale i'Jarnc Address City State Zip Phone Amount of Com rehensive or Theft Deductible Vehicle Year Insurance Carrier Make/Model VIN Dealer Name Address Price Paid For S stem Was Installation Included') Yes CJ No CJ OPTIONAL INFORMATJON A e of Suver: Purchased tor: Yourself CJ AsaGift CJ Annual Household Income: Less than 520.000 CJ $20-40.000 CJ 540-60.000 CJ More than $60.000 CJ c ADV- Date Signature BY YOUR SIGNA TURE BELOW. YOU (II AGREE TO ALL O~ THE TERMS AND CONDITIONS SET ~ORTH IN THIS LIMITED WARRANTY AND (2) YOU UNDERSTAND AND AGREE THAT CODE SYSTEMS. Inc IS PROVIDING YOU WITH A LIMITED WARRANTY AND THAT THIS LIMITED WARRANTY IS NOT AN INSURANCE POLICY 1026699

that may be reasonably required to verify YOUR claim. All documentation received on a claim becomes the Code-Alarm Program Administrator's property and will not be returned. All claim information must be mailed to the Code-Alarm Program Administrator within thirty (30) business days after receipt of the final settlement check from YOUR insurance carrier. For the protection of YOUR rights, YOU are urged to make copies of all materials submitted and to send all materials via registered mail or any other means such that YOUR package can be traced in the event of its becoming lost or misdirected. The Code- Alarm Program Administrator is not responsible for materials not received in the CODE-ALARM Program Administrator's office. Please allow four (4) to six (6) weeks to process any claim hereunder. This limited warranty is not an insurance policy or insurance coverage and is contingent on the existence of and payment from an underlying comprehensive auto insurance coverage and your compliance with all the terms and conditions set forth herein. This limited warranty has no cash value and is subject to all the terms and conditions set forth within this document. This warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES. INCLUDING ANy IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTE WARRANTY, IN NO CASE SHALL CODE-ALARM OR THE CODE-ALARM PROGRAM ADMINISTRATOR BE LIABLE FOR ANY CONSE- QUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to YOU. This warranty gives YOU specific legal rights and YOU may also have other rights which vary from state to state. THIS WARRANTY AND WARRANTY PROGRAM IS NOT AVAILABLE AND MAY NOT BE MARKETED IN OR FROM THE STATE OF FLORIDA. THE CODE-ALARM PROGRAM ADMINISTRATOR Post Office Box 231809 Encinitas, CA 92023 Phone (800) 7082113 POST OFFICE WILL NOT DELIVER WITHOUT PROPER POSTAGE AFFIXED HERE CODE-ALARM LIMITED WARRANTY PROGRAM Post Office Box 231809 Encinitas, CA 92023