Circutor DCP-96 Aac Instruction Manual

Download Circutor DCP-96 Aac PDF Manual (30 pages)

Text of the manual

Warns of a risk, which could result in personal injury or material damage.

ATTENTION Indicates�that�special�attention�should�be�paid�to�a�specifi�c�point. Follow the warnings described in this manual with the symbols shown below. If you must handle the unit for its installation, start-up or maintenance, the following should be taken into consideration: Incorrect handling or installation of the unit may result in injury to personnel as well as damage to the unit. In particular, handling with voltages applied may result in electric shock, which may cause death or serious injury to personnel. Defective installation or maintenance may also lead�to�the�risk�of�fi�re. Read the manual carefully prior to connecting the unit. Follow all installation and maintenance instructions throughout the unit’s working life. Pay special attention to the installation stan- dards of the National Electrical Code. Refer to the instruction manual before using the unit In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result in injury or damage to the unit and /or installations. CIRCUTOR,�SA�reserves�the�right�to�modify�features�or�the�product�manual�without�prior�notifi�cation. DISCLAIMER CIRCUTOR, SA�reserves�the�right�to�make�modifi�cations�to�the�device�or�the�unit�specifi�ca- tions set out in this instruction manual without prior notice. CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifi�cations�and�the�most�updated�manuals.�� www.circutor.com CIRCUTOR, recommends using the original cables and accessories that are supplied with the device.

SAFETY PRECAUTIONS ��3

DISCLAIMER ��3 CONTENTS ��4 REVISION LOG ��5 SYMBOLS ��5 1�- VERIFICATION UPON RECEPTION ��6 2�- PRODUCT DESCRIPTION ��6 3�- DEVICE INSTALLATION ��7 3�1�- PRIOR RECOMMENDATIONS��7 3�2�- INSTALLATION ��8 3�3�- DEVICE TERMINALS ��9 3�4�-CONNECTION DIAGRAM ��10 4�- OPERATION �� 11 4�1�- DISPLAY �� 11 4�2�- KEYBOARD FUNCTIONS �� 11 5�- DISPLAY ��12 5�1�- SINGLE-PHASE NETWORK MEASURING ��12 5�2�- THREE-PHASE NETWORK MEASURE WITH 3 OR 4 WIRE �� 13 6�- CONFIGURATION ��14 6�1�- CONFIGURATION OF THE INPUT ��15 6�1�1�- MEASUREMENT SYSTEM �� 15 6�1�2�- PRIMARY CURRENT ��16 6�1�3�- SECONDARY CURRENT �� 16 6�1�4�- SAVE CONFIGURATION�� 17 6�2�- SYSTEM CONFIGURATION ��18 6�2�1�- CYCLIC DISPLAY �� 18 6�2�2�- DISPLAY BACKLIGHT �� 19 6�2�3�- INITIAL DISPLAY SCREEN �� 19 6�2�4�- ACCESS PASSWORD �� 20 6�2�5�- LIGHT ALARM�� 20 6�2�6�- SAVE CONFIGURATION�� 21 7�- TECHNICAL FEATURES ��22 8�- MAINTENANCE AND TECHNICAL SERVICE ��24 9�- WARRANTY ��24 10�- CE CERTIFICATE ��25 ANNEX A�- CONFIGURATION MENU ��28

Table 1: Revision log

Date Revision Description 11/19 M264B01-03-19A First Version Note: The images on the devices are for illustrative use only and may differ from the original device. SYMBOLS Table 2:Symbols� Symbol Description In accordance with the relevant European directive. In accordance with the CMiM directive. Device covered by European Directive 2012/19/EC. At the end of its useful life, do not leave the unit in a household waste container. Follow local regulations on electronic equi- pment recycling. Direct current. ~ Alternating current.

1�- VERIFICATION UPON RECEPTION

Upon reception of the device check the following points: � a)�The�device�meets�the�specifications�described�in�your�order b) The device has not suffered any damage during transport c) Perform an external visual inspection of the device prior to switching it on d) Check that it has been delivered with the following: - An installation guide If any problem is noticed upon reception, immediately contact the transport company and/or CIRCUTOR’s after-sales service 2�- PRODUCT DESCRIPTION The DCP-96 Aac is a device designed to measure and display the current and the frequency AC three-phase. The device features: - 3 keys that allow you to browse between the various screens and program the device - LCD Display to display all the parameters Table 3: List of DCP-96 Aac models� DCP-96 Aac Model Auxiliary power supply 80 �� 270 V ~ 80 �� 270 V 18 �� 36 V M22450   - M224500030000 - - 

3�- DEVICE INSTALLATION

3.1.- PRIOR RECOMMENDATIONS In order to use the device safely, it is critical that individuals who handle it follow the safety measures set out in the standards of the country where it is being used, using the personal protective equipment necessary (rubber gloves, face protection�and�approved�flame-resistant�clothing)�to�prevent�injuries�due�to�elec- tric shock or electric arc as a consequence of exposure to current-carrying con- ductors and paying attention to the various warnings indicated in this instruction manual. The DCP-96 Aac device�must�be�installed�by�authorised�and�qualified�staff. The power supply plug must be disconnected and measurement systems switched off before handling, altering the connections or replacing the device. It is dangerous to handle the device while it is powered. It is critical to keep wires in perfect condition to avoid accidents, personal injury or damage to installations. Limit�the�operation�of�the�device�to�measuring�the�specified�current�or�voltage�values. The manufacturer of the device is not responsible for any damage resulting from failure by the user or installer to heed the warnings and/or recommendations set out in this manual, nor for damage resulting from the use of non-original products or accessories or those made by other manufacturers. Do not use the device to take measurements if you detect an anomaly or malfunction. Disconnect the device from the mains and from the power supply (both the device and its measuring system) before performing any maintenance work, repairs or handling any of the connections of the device. Contact the after-sales service if you detect that the device is not working prop- erly.

Terminals, opening covers or removing elements can expose parts that are

hazardous to the touch while the device is powered. Do not use the device until it is fully installed. The device should be installed inside an electric panel or enclosure, and panel-mounted. The following steps must be taken for correct installation: 1�- Make a cut in the panel, according to the dimensions in Figure 1� 91 91 Figure 1: Cut in the panel� 2�- From outside, insert the device into the panel cut-out (Figure 2). Figure 2: Insert the device� 3�- Fully insert the device and fasten it by using the spring (Figure 3). Figure 3: Fully insert the device� The device must be connected to a power circuit protected by a fuse with a maximum nominal

current of 0�25 A.

If more than one device is connected to the current transformer, they must be connected in series. Before disconnecting the current measurement connection cables, be sure to disconnect the transformer’s primary cables and bridge the secondary. The device can operate in three-wire, three-phase mode or four-wire, three-phase mode, the user selecting the corresponding connection mode according to the installation. An incorrect type of connection or an error in phase sequence may cause measurement errors. 3.3.- DEVICE TERMINALS Table 4: List of DCP-96 Aac terminals� Device terminals 1: L/+, Power supply 6: I2 S1, Current input L2 2: N/-, Power supply 7: I2 S2, Current input L2 4: I1 S1, Current input L1 8: I3 S1, Current input L3 5: I1 S2, Current input L1 9: I3 S2, Current input L3 2 1 4 1 2 4 5 6 7 5 6 7 8 9 8 9 Figure 4: DCP-96 Aac terminals�

CARGA / LOAD

2 1 4 5 6 7 8 9 Figure 5: Current measurement�

The device has a LCD display with 3 lines, 4 digits each, to view the measured parameters and

Circutor DCP-96 Aac Instruction Manual

Text of the manual

Warns of a risk, which could result in personal injury or material damage.