B-Tech BT8710 Installation Manual

• Max load: 70kg (154lbs) per screen • Suitable for displays with fixings up to 600 x 400mm • Stand dimensions: H.1969 x W.2005 x D.165mm • Integrated cable management SPECIFICATIONS www.btechavmounts.com B-TECH AV mounts 65" 165CM BT8710 PREMIUM FLOOR-TO-WALL TWIN SCREEN VC STAND INSTALLATION GUIDE PER SCREEN

surfaces are not suitable for installation. Designed for indoor use, this mount is suitable for public or home installation If located in a public or frequently populated area ensure that the product is out of the immediate reach of people. If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling. When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so. 2 CONTENTS Installation Safety Notes...................................................................................................................... Parts List.................................................................................................................................................... Installation Instructions....................................................................................................................... Product Dimensions............................................................................................................................ B-Tech Contact Details....................................................................................................................... 2 4 6 18 20 INSTALLATION SAFETY INSTRUCTIONS CAUTION: Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference. Please check carefully to make sure there are no missing or defective parts - defective parts must never be used. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire. General B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product. Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped. If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death both during installation and at any time thereafter. Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing. This weight limit will be clearly stated on each product and its packaging and will vary from product to product. Product location Fixing hardware It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store. Hazard limitation When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double-check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness. It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualified person. This stand is intended for use only with the maximum weights indicated. Use with screens heavier than the maximum indicated may result in instability causing possible injury.

PLEASE KEEP THIS FOR FUTURE REFERENCE 4 A3 B1 A1 C1 D1 D2 A7 E1 F1 G1 G2 G3 G10 B2 NOT REQUIRED A2 INSTALLATION TOOLS REQUIRED Pliers/Cutter Crosshead Screwdriver Drill Pencil 10mm Masonry Drill bit Spanner

M6 x 12mm HEX SCREW 4 COVER STRIP 8 8 4AF HEX KEY 3AF HEX KEY SQUARE NUT (OPTIONAL) M6 x 12mm GRUB SCREW (OPTIONAL) 8 ITEM PART REF DESCRIPTION QTY COLUMN FLOOR TO WALL KIT MOUNTING BRACKET RAIL 2 8 8 2 2 8 8 1 2 MOUNTING RAIL END CAP A9 C1 C2 C3 C4 2 2 C5 C6 C7 D1 D2 RAIL-TO-COLUMN MOUNTING BRACKET M8 x 12mm SCREW M6 x 40mm CSK HEX SCREW 5AF HEX KEY 4AF HEX KEY M8 SLIDING INSERT RECTANGLE NUT A5 A6 C5 C4 C3 A8 A9 A4 C2 C7 E2 C6 E3 E4 E5 E6 E7 E8 E9 E11 E13 E15 E14 G5 G6 G7 G8 G9 G11 G12 E10 ARMS SCREEN FIXING KIT VC SHELF E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 M4 x 25mm SCREW M4 x 12mm SCREW M6 x 16mm SCREW M4 x 40mm SCREW M6 x 40mm SCREW M6 x 25mm SCREW M8 x 25mm SCREW M8 x 16mm SCREW MULTIWASHER M8 x 40mm SCREW 13mm SPACER 5mm SPACER 24mm SPACER 8 8 8 8 8 8 8 8 8 8 8 8 8 4 2 SCREEN INTERFACE ARM 5AF LONG HEX KEY E11 E12 E13 E14 E15 G1 1 1 1 2 4 4 G2 G3 G4 G5 G6 4 G7 4 G8 G10 G11 G12 HOOK ARM SLIDING BRACKET EXTENSION BRACKET M8 x 55mm HEX SCREW M8 NUT WASHER M8 x 16mm HEX SCREW M8 SPRING WASHER 2 G9 SHELF 1 M4 x 10mm SCREW 4 UNC 1/4" x 1/2" SCREW 1 E12 G4 M8 x 20mm HEX SCREW B1 B2 B3 B4 B5 B7 B6 4AF HEX KEY M6 x 12mm SCREW 4 WALL PLATE 2 BASE PLATE 2 M8 x 50mm COACH SCREW 8 N°.10 x 50mm WALL PLUG 8 M8 T1.5mm METAL WASHER 8 2 B3 B4 B6 B7 B5 ADAP- TORS 600mm ADAPTOR ARM M8 x 12mm SCREW 4 8 F2 F1 F2

i. Insert 4 x item C2 into item C1 and attach item C3. Screw two full turns to leave item C3 at the end of item C2. C6 1. C3 C2 SLOTS ii. Slide item C1 down the front slots of item A1 to the correct height and tighten item C2. Repeat for both columns. C6 C2 C1 C1 A6 A5 A6 A5 REAR REAR FRONT A3 A1 OPTIONAL - FIX REAR COVER TO COLUMNS Place item A3 into the back of item A1. Use items A5 & A6 at the top and bottom of the column slot to secure rear cover. A8 A6 A5 A3 A1 A1 C2 C3 M6 x 40mm CSK HEX SCREW RECTANGLE NUT A5 A6 SQUARE NUT M6 x 12mm GRUB SCREW

Fix item B1 to the top of item A1 using item B3. B1 A1 B1 B7 B3 CONCRETE FLOOR GROUND ANCHOR GROUND ANCHORS (not supplied) FLOOR 3. 06.5mm 150mm 600mm 60mm WALL TOP VIEW WALL FIX FLOOR PLATES TO FLOOR Fix item B2 to floor (fixings not included). Note: Fixing points are 60mm away from the wall and the floor plates should be set 600mm apart. A1 B2 B2 B2 B3 M6 x 12mm HEX SCREW

Using the guide pins, place item A1 onto item B2. Mark the 4 fixing holes from item B1 onto the wall for each column. B1 B2 A1

Remove item A1 and drill marked holes. Insert 4 x item B6 for each column (Not required for wood/stud walls). WALL 10mm Masonary Drill Bit MASONARY WALL B6

i. Insert 4 x item C4 into item D1 (2 in the top channel, 2 in the bottom channel) on each side of the rail. ii. Screw 2 x item C5 into item C4 in the top channel - allow at least a 6mm gap so the rail can be hooked on to item C1. iii. Hook item D1 onto items C1 and fix with in place with item C5. 6. 6mm+ 185mm D1 C4 C4 D1 A1 C1 C5 C5 C4 D1 185mm 415mm 608mm C4 C5 C7 C4 C5 C7 D1 C7 C5 C4 C5 M8 x 12mm HEX SCREW M8 SLIDING INSERT

iii. Attach item D2 to the ends of items D1.

ii. Attach item G10 to item G2. using items G7 & G8. ASSEMBLE VC SHELF Note: The shelf adaptor can mount the shelf above or below the screens. Assembly shows shelf mounted below the rail / screens. 13mm Spanner Optional Add extension bar For an extended reach attach item G3 onto item G2 using items G7 & G8. G8 G8 G7 G3 G2 G7 C5 G10 G8 G7 C5 G10 G2 G1 G6 G5 M8 NYLOC NUT M8 METAL WASHER M8 SPRING WASHER M8 x16mm HEX SCREW G5 G6 G7 G8

ii. Secure shelf to rail. Use item G4 on the bottom of item G1 to secure the shelf to item D1. Optional: Level the shelf bracket by adjusting item G4 on top of item G1. i. Hook item G1 onto item D1. REVERSE MOUNTING ABOVE THE SCREEN MOUNTING To reverse mount the shelf, use item G9 to mount item G10 onto the back of item G3. Shelf shown mounted above the rail. ALTERNATIVE SHELF MOUNTING OPTIONS G9 G10 G3 G2 D1 G1 G4 G4 G1 E2 G4 M8 x 20mm HEX SCREW G9

TOP BOTTOM SCREEN E3-E11 E12 E1 E1 E14 E14 Fix item E1 to the rear of the screens using items E3 - E15. Note: Ensure the arms are facing the correct way round and the same holes are used on all arms. SCREEN INTERFACE ARM 13mm SPACER Note: 13mm spacers are not required if the VC shelf is not being installed or if reverse mounting the shelf. E1 F1 F2 600mm ADAPTOR ARMS Note: Use (if required) for 65”screens with VESA 600 x 400mm fixings i. Attach item F1 to item E1 using item F2. ii. Fix item F1 to rear of screen using the interface kit (items E3-E14). SCREEN

SCREEN Tighten the safety screws on the bottom of item E1 securing the screens to item D1. Optional: HEIGHT ADJUSTMENT SCREW SAFETY SCREW Safety Screw Engaged SCREEN Note: If necessary, adjust the height adjustment screws on top of item E1 to level the screen. E2 11. E1 D1 A1 HOOK SCREENS ONTO RAIL SCREEN Use items E1 to hook the screens onto item D1. SCREEN SCREEN

TO SHELF Fix camera to item G10 using either item G11 or item G12. VC CAMERA SCREEN G10 G11 G12 G11 G12 M4 x 10mm SCREW UNC 1/4” x 1/2” SCREW 13. ATTACH STRIPS Insert item A7 to the front and back of item A1. Note: Item A7 may have to be cut down to size to be able to fit into the front of item A1. Use pliers to cut item A7 to correct size A7 A1 A7

FRONT VIEW These instructions are intended as a guide only and B-Tech accepts no liability for the accuracy of the information contained in this document. 400mm 300mm 200mm 100mm 8.4mm 120mm 180mm 1404mm 60.8mm 20mm 150mm 66mm 6.5mm 9mm 51mm BOTTOM VIEW

TOP VIEW REAR VIEW SIDE VIEW These instructions are intended as a guide only and B-Tech accepts no liability for the accuracy of the information contained in this document. 2005mm 60.3mm 90mm 51mm 30mm 100mm 100mm 80mm 42mm 400.1mm 428mm 159mm 20.5mm 1900mm 6mm 253.1mm Min - 231mm / Max - 627.5mm 20mm 15mm 50mm 50mm 50mm 8.5mm 60.8mm 366mm 1949mm

B-TECH AV mounts AMA-BT8710-V1-1020-104 MADE IN VIETNAM ©2020 B-Tech AV Mounts. All rights reserved. B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd. B-Tech AV Mounts and the B-Tech logo are registered trade marks. All other brands and product names are trademarks of their respective owners. Photographs are for illustrative purposes only. E&OE. CONTACT: [email protected]