Argus Copper Box v4 Manual 

© by intec Gesellschaft für Informationstechnik mbH D-58507 Lüdenscheid, Germany, 2020 All rights, including translation rights, reserved. No part of this work may be reproduced, duplicated or disseminated in any form (print, photocopy, microfilm or any other method) without written consent. All rights are reserved. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without intec´s permission.

3 1 Introduction .........................................................................................4 2 Safety information ..............................................................................7 3 General technical data .....................................................................13 4 Configuring accesses ......................................................................17 5 Using the ARGUS Copper Box v4 ...................................................18 5.1 Selecting and activating the Copper Box .......................................18 5.2 Hotkeys / settings .............................................................................20 5.3 Changing socket selection ..............................................................22 5.4 Alarm tones .......................................................................................23 6 Auto test ............................................................................................25 7 Voltage measurement (U= and U~) .................................................35 8 Capacitive symmetry measurement (CSym) ..................................42 9 Capacitance measurement (C) ........................................................46 9.1 Calculating line length .....................................................................49 10 Isolation resistance measurement (Iso.) ........................................51 11 Resistance symmetry (RSym) .........................................................55 12 Loop resistance measurement (R) ..................................................62 12.1 Calculating line length .....................................................................65 13 DC current measurement (I=) ..........................................................66 14 Longitudinal conversion loss (LCL) ...............................................68 15 Near-end crosstalk (NEXT) ..............................................................71 15.1 Starting NEXT measurement ...........................................................73 16 Signature detection/termination detection .....................................75 16.1 Possible results ................................................................................77 17 Fast cable check ...............................................................................79 17.1 Possible results ................................................................................80 18 Remote kit control (Rem.) ................................................................81 19 Appendix ...........................................................................................84 A) Abbreviations .....................................................................................84 B) Software licenses ...............................................................................87 C) Index ..................................................................................................88

1 Introduction ARGUS Copper Box v4 With the ARGUS Copper Box, intec offers an expansion for the xDSL multitesters ARGUS 15x and ARGUS 16x. This USB box enables you to detect dangerous voltages and currents early on and reliably assess the physical quality of the line – particularly when DSL synchronisation is not possible or the data rate is low due to asymmetry, interference sources or other mechanical line problems. The box is connected to the ARGUS tester simply via the USB host interface. You can select the box and perform all measurements easily and rapidly via the ARGUS graphical user interface. The ARGUS Copper Box is equipped with four standard banana sockets, which are colour-matched to the respective cables. These sockets are designed for a four millimeter (4 mm) thick, contact-protected banana cable.

5 Further features of the ARGUS Copper Box v4: - Multiple, preconfigured measurement profiles can be executed as an auto test. - Voltage measurement enables measurement of the supply voltage (e.g. SHDSL, ISDN- BRI U, POTS), as well as external voltages caused e.g. by contact between two wires or isolation faults. - With the aid of capacitive symmetry measurement, it is possible to detect asymmetry in the subscriber line that can result in signal distortions or transmission errors. - Capacitance measurement detects interruptions as well as typical input capacitances of connected devices and enables estimation of line lengths. - Isolation resistance measurement reveals damage to cable isolation, moisture penetration or oxidised contact points. - With the aid of resistance symmetry measurement, it is possible to detect irregula- rities in the subscriber line that can result in signal distortions or transmission errors. - Loop resistance measurement aids detection of short circuits and estimation of line lengths. - DC current measurement can be used to detect emergency, external and normal power feeds as well as breaks in the line. - Unbalance measurement (LCL): This measurement uses a frequency of 1 MHz to measure asymmetry in a line pair. - NEXT measurement: Measurement of near-end crosstalk at a frequency of 1 MHz. - Signature detection is used to detect the signatures and test terminations (PPAs) connected to the subscriber line. - The fast cable check verifies the correctness of a three-pole (Tip/Ring/Ground) connection. - The integrated remote kit control lets you remotely set the line end to the desired state either manually or automatically using a variety of electronic instrument kits.

All measurements can be executed as highly accurate automatic TRG (Tip, Ring, Ground) measurements. With its light weight of less than 160 grams and sturdy plastic housing, the ARGUS Copper Box is not only extremely compact but also insensitive to impacts, falls, and other mechanical hazards. Despite its exceptional performance and high measuring voltage, the Box can operate for exceptionally long periods, as it is supplied by the powerful Li ion battery pack of the ARGUS tester. Its compatibility enables the Box to be used with multiple ARGUS test instruments. Thus, an installation team can expand multiple ARGUS meters independently of each other. It is not necessary to return testers for servicing in order to expand their functionality. A special protective rubber jacket forms the USB box and the ARGUS tester into a single unit. The Copper Box can be kept up to date quickly and easily via firmware updates that ARGUS executes automatically. This insures that the Copper Box and ARGUS firmware is always optimally matched. The standard scope of supply includes a high-quality connection lead (twisted), a ground lead and this manual. For further questions, please contact: intec Gesellschaft für Informationstechnik mbH Rahmedestr. 90 D-58507 Lüdenscheid Tel.: +49 (0) 2351 / 9070-0 Fax: +49 (0) 2351 / 9070-70 www.argus.info/en [email protected]

ARGUS Copper Box 7 2 Safety information General safety information: The ARGUS Copper Box may only be operated using the accessories supplied with the device. The use of other accessories can result in faulty measurements or even damage to the ARGUS Copper Box and the connected equipment. Only use the ARGUS Copper Box according to the instructions contained in this manual. Any other use can result in injuries to persons and destruction of the ARGUS and/or the ARGUS Copper Box. 1. Before connecting the ARGUS Copper Box to an access, make sure that no dangerous voltages or currents are present for which the ARGUS Copper Box or its accessories are not specified. Also keep in mind that the voltage can change over the time that the device is connected. 2. The ARGUS Copper Box is intended solely for use in telecommunications networks with limited power. It is not intended to be used e.g. to measure mains voltages (230 V/50 Hz). Specifications: DC voltage UDC (U=): AC voltage UAC (U~): Capacitance measurement C (C, Csym): Isolation resistance measurement Iso (Iso): Loop resistance R (R, Rsym): DC current IDC (I=): Longitudinal conversion loss, (LCL): Near-end crosstalk (NEXT): 0.01 V to 200.0 V 0.01 V to 200.0 V (50 Hz sine) 0.01 nF to 8000.00 nF @ 8Hz 0.1 kΩ to 999.9 MΩ, (105 V, max. 2 mA) 0.1 kΩ to 40.0 MΩ, (8 V, max. 9 mA) 0.1 to 40.0 MΩ, (13 V, max. 15 mA) 0.1 mA to 499.9 mA Attenuation for 1 MHz @120 Ω Crosstalk attenuation for 1 MHz @120 Ω 3. Use the ARGUS Copper Box only according to its intended purpose at all interfaces and accesses. It is intended for the measurement and acquisition of physical quantities in low-power telecommunication networks. The ARGUS Copper Box is not designed for any other applications (e.g. measuring electronic components, determining the out- put quantities of voltage sources, etc.). 4. In each measurement, avoid any contact with electrically live components (sockets, plugs, cables, adapters, etc.) under all circumstances. 5. Voltages over 50 V AC and 120 V DC can cause death. 6. The ARGUS Copper Box may only be used by trained personnel. 7. The ARGUS Copper Box is not water-tight. Therefore, protect the ARGUS Copper Box against water penetration. 8. The USB connection lead of the ARGUS Copper Box may only be connected to approved ARGUS testers (ARGUS 15x and ARGUS 16x). Each of these testers must be enabled using an individual option key provided especially for this purpose. The USB lead must not be extended.

8 ARGUS Copper Box 9. The electromagnetic compatibility (EMC) was tested according to the regulations specified in our declaration of conformity. The ARGUS Copper Box is a class A device. This device can cause radio interference in residential areas. In this case, the user may be required to implement appropriate measures. 10. If the ARGUS Copper Box is operated under extreme conditions, an internal protective mechanism (protection element) can be activated to protect the device, the Box and the user. In this case, the Box may no longer be used, and may only be repaired by autho- rized personnel. The device may not be opened by unauthorized personnel. 11. To ensure dependable, long-term operation of the ARGUS Copper Box, always make sure that it is optimally protected against high temperatures. The ARGUS Copper Box may only be operated with the temperature range permitted for the ARGUS device (-10 °C to +50 °C in battery operation, 0 °C to +40 °C in adapter operation).

ARGUS Copper Box 9 Important instructions for use: 1. Even a measurement on low-power telecommunications networks can present hazards - particularly in the event of a fault; consequently, always first check the line to be tested for a supply (DC voltage) and an external voltage (DC or AC voltage). If even one of these conditions is present, safely de-energise this voltage and secure it against being switched on again before conducting any further tests. 2. Once ARGUS detects the ARGUS Copper Box, an auto test can be executed or each separate measurement can be started and stopped individually. If you change the measurement without first stopping, the measurement is stopped automatically. All voltages >200V are outside the permissible limits. 3. Never switch the ARGUS Copper Box from line to line while a measurement is running. This would bypass the safety voltage measurement conducted before the start of each measurement. Connecting the Box with a running resistance measurement to a line with a regular supply voltage, for example, could destroy the Box even if this voltage is within the specification for voltage measurement. In general, the ARGUS Copper Box automatically checks before every measurement (except current measurement) whether the line is carrying a voltage, and stops the measurement with a message as necessary. 4. The ARGUS Copper Box is equipped with an automatic “TRG-opt.” measurement. This means that the measurement quantities can be measured between different wires, such as a (Tip), b (Ring), Ground and optional socket (opt.). The ARGUS tester displays for selection the pairings that the ARGUS Copper Box supports for the various measurements. Except for measurement of isolation resistance, the ARGUS Copper Box performs a continuous measurement when only one wire pair (e.g. Tip/Ring or Tip/ Ground or Ring/Ground) is selected, i.e. changing values appear immediately on the display.

10 ARGUS Copper Box Special instructions for individual measurements Voltage Be sure to observe the permissible measuring range specified above when measuring voltage. Capacitance/capacitive symmetry: Before measuring, make sure that the voltage thresholds given in the table below (see page 11) are not exceeded during the measurement. Certain measurements can require a longer settling time. An automatic “TRG-opt.” measurement can thus take some time. Isolation resistance: Before measuring, make sure that the voltage thresholds given in the table below (see page 11) are not exceeded during the measurement. During the measurement, the ARGUS Copper Box can apply a measuring voltage of up to 105 V max. 1 mA) to the line. Certain measurements can require a longer settling time. An autotest can thus take some time. Loop resistance/resistance symmetry Before measuring, make sure that the voltage thresholds given in the table below are not exceeded during the measurement. During the measurement, the ARGUS Copper Box can apply a measuring voltage of up ton 13 V (max. 15 mA) to the line. DC current: Be sure to observe the permissible measuring range specified above when measuring DC current. Make sure you connect the ARGUS Copper Box in the circuit in series. Longitudinal conversion loss/NEXT: Before measuring, make sure that the voltage thresholds given in the table below are not exceeded during the measurement. When measuring LCL or NEXT using the ARGUS Copper Box, any type of additional measurement lead can falsify the measurement. Both the length and the position of the measurement leads with respect to each other can influence the measurement result significantly. The specification values apply only for the Box itself and not for the system comprising the Box and the measurement leads. Consequently, connecting the telecommunications line directly to the Box is recommended. Signature detection/fast cable check/remote kit control Before measuring, make sure that the voltage thresholds given in the table below are not exceeded during the measurement.

ARGUS Copper Box 11 Voltage thresholds Measurement UDC (V) to UAC (Veff) to R* 3.5 30 R-sym* 30 30 ISO-R* 5 30 C* 17 17 C-sym* 17 17 LCL 10 7 NEXT 10 7 Signature 3 3 Fast cable check** 5 30 Remote box** 3 3 * Measured on 200 kΩ load ** Loop limit value 10 kΩ

12 ARGUS Copper Box Return and environmentally compatible disposal Current environmental law restricts the use of certain hazardous substances in electrical and electronic devices, in particular the concentration or use of lead (Pb), cadmium (Cd), mercury (Hg), hexavalent chromium [Cr(VI)], polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE). We hereby confirm that, according to the assurances, marking and documentation of our suppliers, ARGUS brand measuring products do not contain any substances in concentrations, compounds or applications whose marketing is prohibited according to the valid provisions of the RoHS Directive 2011/65/EU of the European Parliament and Council dated 8 June 2011. Our registration number issued by the EAR is: WEEE REG. no. DE 92829367. Since October 2005, we have been marking all our measuring devices with this symbol, in compliance with WEEE 2002/96/EC and the corresponding German statute ElektroG: ( ) (DIN EN 50419). In other words, ARGUS and its accessories, may not be disposed of as household waste. Please consult with our Service department with respect to the return of old devices.

ARGUS Copper Box 13 3 General technical data ARGUS user safety tested according to EN62368-2 RoHS conformity pursuant to the WEEE directive The electromagnetic compatibility (EMC) was tested according to the regulations specified in our declaration of conformity. CE marking The ARGUS Copper Box complies with EC directives 2004/108/EC and 2009/C197/03. We will be happy to pro- vide a detailed declaration of conformity on request. Device specifications: The ARGUS Copper Box is intended solely for measurements in telecommunications networks with limited power. Make sure that the inserted banana plugs of the measuring leads are completely enclosed by the sockets of the Copper Box. Dimensions/weight Inputs/outputs Height: 125 mm Width: 74 mm Depth: 22 mm Weight: approx. 160 g - 4 x 4 mm banana sockets (contact-protected) - USB-A plug Temperature range Operating temperature (ARGUS in battery mode): -10 °C to +50 °C Storage temperature: -20 °C to +60 °C Humidity: up to 95 % relative, non-condensing Miscellaneous

14 ARGUS Copper Box Measuring accuracies: Voltage: DC voltage measurement (U=): Measuring range: Resolution: Accuracy: 0.01 V - 9.99 V 0.01 V ±(0.5 % + 2 digits) 10.0 V - 200.0 V 0.1 V ±(0.5 % + 2 digits) AC voltage measurement (sine, 50 Hz) (U~): Measuring range: Resolution: Accuracy: 0.01 V - 9.99 V 0.01 V ±(2 % + 2 digits) 10.0 V - 200.0 V 0.1 V ±(1.5 % + 2 digits) Frequency: 10 Hz to 200 Hz; 0.2 Hz; ±(1.5 % + 2 digits); sine When measuring voltages, the input resistance depends on the measuring range: - Measuring range 1: 0 V - 25 V; Input resistance: 1.694 MΩ - Measuring range 2: 25 V - 200 V; Input resistance: 1.05 MΩ As soon as the total of all voltages exceeds 25 V, the measurement is switched over. Capacitive symmetry measurement (CSym): Measuring range: Resolution: Accuracy of capacity diffe- rence: 10 nF - 4 µF 0.01 nF 0.1% of the capacity to ground Capacitive measurement, measuring frequency 8 Hz (C): Measuring range: Resolution: Accuracy:* 0.01 nF - 9.99 nF 0.01 nF ±(4 % + 4 digits) 10.00 nF - 99.99 nF 0.01 nF ±(4 % + 4 digits) 100.0 nF - 999.9 nF 0.1 nF ±(3 % + 1 digit) 1000 nF - 8000 nF 1 nF ±(3 % + 1 digit) * All specifications relate to a comparison measurement using film capacitors.

ARGUS Copper Box 15 Isolation resistance measurement with 105 V, max. 2 mA (Iso.): Measuring range: Resolution: Accuracy: 0.1 Ω - 99.9 Ω 0.1 kΩ ±(2 % + 1 digit) 100.0 kΩ - 999.0 kΩ 1 kΩ ±(2 % + 1 digit) 1.00 MΩ - 9.99 MΩ 10 kΩ ±(2 % + 1 digit) 10.0 MΩ - 99.9 MΩ 100 kΩ ±(5 % + 1 digit) 100.0 MΩ - 999.9 MΩ 100 kΩ ±(5 % + 1 digit) Isolation resistance measurement with 8 V, max. 9 mA (Iso.): Measuring range: Resolution: Accuracy: 0.1 Ω - 99.9 kΩ 0.1 kΩ ±(2 % + 1 digit) 100.0 Ω - 999.0 kΩ 1 kΩ ±(2 % + 1 digit) 1.00 MΩ - 9.99 MΩ 10 kΩ ±(2 % + 1 digit) 10.0 MΩ - 40.0 MΩ 100 kΩ ±(5 % + 1 digit) Resistance difference (RSym): Measuring range: Resolution: Accuracy: 10 Ω - 5 kΩ 0.1 Ω ± 0.2 % of RLoop ± 0.2 Ω Loop resistance measurement with 13 V, max. 15 mA (Iso.): Measuring range: Resolution: Accuracy: 0.1 Ω - 999.9 kΩ 0.1 Ω ±(1 % + 3 digits) 1.000 Ω - 9.999 kΩ 1 Ω ±(1 % + 1 digit) 10.00 Ω - 99.99 kΩ 10 Ω ±(1 % + 1 digit) 100.0 Ω - 999.9 kΩ 100 Ω ±(1 % + 1 digit) 1.000 MΩ - 9.999 MΩ 1 kΩ ±(2 % + 1 digit) 10.0 MΩ - 40.0 MΩ 10 kΩ ±(5 % + 1 digit) DC current measurement (I=): Measuring range: Resolution: Accuracy: 0.1 mA - 499.9 mA 0.1 mA ±(2.5 % + 3 digits)

16 ARGUS Copper Box Unsymmetrie balance at 1 MHz (LCL): Measuring range: Resolution: Accuracy*: 0.1 dB - 55.0 dB 0.1 dB ± 1.5 dB 55.1 dB - 65.0 dB 0.1 dB ± 3 dB The length of the measuring leads can significantly affect the measurement. Therefore, always use the original accessories for measuring. Near-end crosstalk at 1 MHz (NEXT): Measuring range: Resolution: Accuracy: 0.1 dB - 65.0 dB 0.1 dB ± 1 dB The length of the measuring leads can significantly affect the measurement. Therefore, always use the original accessories for measuring. Reference conditions (calibration): - Temperature: +23 °C to 5 °C - Humidity: 50 % ± 20 %, relative, non-condensing - Frequency of measurement quantity: 50 Hz ± 5 Hz, sine

17 ARGUS Copper Box 4 Configuring accesses This section describes how to select and configure the access type "Copper Test". First though, note that ARGUS offers 100 user-configurable accesses, which can be configured as DSL, ISDN or copper test accesses according to the customer's requirements. Generally, some of these 100 accesses are pre-configured before delivery. At least one access with the name "Copper tests" should appear in the list of accesses when you power up ARGUS. This should be sufficient, as the Copper Box can be started on this access as an individual test just like TDR or Line scope. Switch on ARGUS. The most recently used access is indi- cated on the display with . ARGUS additionally displays a preview of the selected access settings. The preview window opens after 2 seconds. You can also change the access name "Copper tests", e.g. to in Copper Box, TDR similar. See the ARGUS manual for instructions on editing access names. See section nocties of the ARGUS manual for instructions on editing notices. Creates an access, see ARGUS manual. Edits an access, see ARGUS manual. Toggles softkey assignment, see ARGUS manual. Switches to main menu. Switches to Access, see ARGUS manual.

18 ARGUS Copper Box 5 Using the ARGUS Copper Box v4 First connect the ARGUS Copper Box with the USB host interface of an ARGUS tester. You may need to enter an option key in the ARGUS tester under Settings/Device/Software options. Then connect the device to the measurement configuration as shown in the connection examples. Connection example 1 (DSLAM direction): Connection example 2 (Modem direction): 5.1 Selecting and activating the Copper Box The chapter "Configuring accesses", page 17, explains how to set up the connection type "Copper test". ARGUS in the status display. The device always measures the DC voltage at the line socket (pins 4/5) before executing a copper test. This value should warn of the presence of a voltage at the line socket (e.g. TDR, Line scope) when a copper test is executed. Select one of the copper tests. In this example Copper Box. This is not the value that the Copper Box measures between the Tip and Ring wire. ARGUS automatically switches to the Copper Box auto test configuration, page 27. Copper Box Continued on next page

19 ARGUS Copper Box ARGUS detects the Copper Box. This can take a few seconds. If a conflict occurs, update your firmware or consult our Service Department. When detection is complete, ARGUS activates the Copper Box and starts voltage measurement immediately. ARGUS is in the Copper Box status display. The voltage between the Tip and Ring wire is measured continuously here. Shows the current measured value. The continuing measurement is paused. You can use the cursor keys to select individual tests, in this example capacitive symmetry mea- surement. Opens the Copper Box menu, see page 20. Starts the capacitive symmetry measurement.

20 ARGUS Copper Box Copper Box menu. Depending on the currently selected test, you can choose among the following configurations (see in the sheet under), here for example the hotkeys for capacitive symmetry measurement (Csym). 5.2 Hotkeys / settings The hotkeys/settings can vary depending on the selected sockets. Hotkey Number key 0 Reset (only for active (min/max display)) Number key 1 Auto test profile, s. page 26 Number key 3 Polarity (Iso. only), s. page 52 Number key 4 Range limit (Iso. only), s. page 52 Number key 5 Measuring voltage (Iso. only), s. page 52 Number key 6 Wire types (R, RSym, C, CSym), s. page 31 Number key 7 QR code (only at the end of an auto test) Number key 8 Susceptibility, s.page 43 Number key 9 Display mode, s. page 36 Input resistance, s.page 36 Press one after another and Remote kit commands commands, s. page 83 Remote kit s. page 81 Information bell, s. page 36

21 ARGUS Copper Box You can find more information on the respective configurations in the chapter "Tests". Press one after another and Copper Box info. You can find more detailed information on the Copper Box here, such as Copper Box type, software version, serial number, etc. Press one after another and Save (only at the end of an auto test)

22 ARGUS Copper Box 5.3 Changing socket selection By default, tests are conducted on the T/R sockets. Use socket selection to choose between which wires you want to measure. In the following example, a measurement between sockets Tip and Ground are selected. You can select a variety of socket combinations using the cursor key. Red Tip (a-wire) Black Ring (b-wire) Green GND Blue opt. (optional) White not selected Opens the Copper Box menu, see page 20. Starts voltage measurement between sockets Tip and GND. Switch to socket selection using the cursor keys. 3x right cursor key

23 ARGUS Copper Box In this example, sockets Tip, Ring and GND are selected. Each measurement between two sockets (e.g. on Tip/Ring) is always performed in real time. 5.4 Alarm tones ARGUS generates various alarm tones in conjunction with the Copper Box, for instance as soon as a fault occurs or a test has been concluded. The alarm tones must be activated in the ARGUS settings, see Main Manual. Short - short Fault: - Immediately when an external voltage is detected. - In the absence of a loop or ground (RSym). - In the absence of a ground/line or presence of a loop (CSym). Short - long Test complete: - After every test that ended automatically. - After every auto test - (not after every individual test here). Short - short - long In the event of a fault at the end of a test. Long Prompts for user input. Opens the Copper Box menu, see page 20. Starts voltage measurement via sockets Tip. Ring and GND.

ARGUS Copper Box 25 6 Auto test ARGUS executes various tests automatically, depending on the configured auto test pro- file. Ten user-configurable profiles (including measurement assistance control) are avail- able for auto test. A voltage check is performed before every measurement (except current measurement) in which the voltage limits given in the table (see page 11) may not be exceeded. The measuring ranges, resolutions and accuracies of the respective measurement may be found in the chapter Technical data, see page 14. Auto test settings ARGUS in the status display. open the profile selection The auto test is not yet started. Hotkeys / settings auto test See the respective chapters for details on the individual measurements. In the following, the procedure is described using an auto test example. Auto test profile, s. page 26 Wire types, s. page 31 Press one after another and Remote kit command, s. page 83 Remote kit, s. page 81 Press one after another and Copper Box info, s. page 21

26 ARGUS Copper Box Auto test profile selection Select the profile to be editied and open it with . The auto test it configured under Auto test configuration, see page 27.

ARGUS Copper Box 27 Settings Description Auto test profiles: Auto test/ auto test with instrument kit/ Copper Box auto test All available Copper Box tests can be compiled in an automated test. Five different profiles are available for saving. Auto test sequence Sets the wait inter- val until the next test. This setting only applies for the respectively selected test. Range: 100 ms to 5000 ms. Default: 100 ms Adds further tests. Deletes the currently selected test. Selection of e.g. RSym Different socket combinations are available depending on the selected test, see page 29. Confirm socket selection with.

28 ARGUS Copper Box Selection of susceptibility to interference, see also page 59. Select the start function: - Automatic start - Pause: manual loop ARGUS waits for user input to confirm that the loop is connected. The selected test, in this example RSym, has been added to the auto test. Switches softkey assignment

ARGUS Copper Box 29 < -> > Shifts the marked test one position to the right. < <- > Shifts the marked test one position to the left. The added test and the test sequence are saved. Different socket combinations are available depending on the test. U / R / Iso. / C Possibility 1: a1/T1, b1/R1 Possibility 2: a1/T1, GND Possibility 3: b1/R1, GND Possibility 4: a1/T1, b1/R1, GND Possibility 5: a1/T1, opt. Possibility 6: b1/R1, opt. Possibility 7: a1/T1, b1/R1, opt. Possibility 8: a1/T1, b1/R1, GND, opt. I= Possibility 1: a1/T1, b1/R1 Possibility 2: a1/T1, GND Possibility 3: b1/R1, GND Possibility 4: a1/T1, opt. Possibility 5: b1/R1, opt. CSym / RSym Possibility 1: a1/T1, b1/R1, GND Possibility 2: a1/T1, b1/R1, opt. Rem. Possibility 1: short-circuit a/T-b/R Possibility 2: exchange connect Possibility 3: short-circuit a/T-b/R-GND Possibility 4: open circuit Possibility 5: activate tone generator You must confirm the selected socket combination with .

30 ARGUS Copper Box You can define the input resistance for voltage measurements. Determines whether the voltage measurement is to be carried out with an input resistance of 1 MΩ (high-ohm, standard) or low-ohm (200 kΩ). Default: high-ohm (standard) For R, Rsym, Iso., C and Csym measuremnets, you can select the susceptibility which ARGUS sholud use for measuring. Default: Reliable for external voltages Notice Allows you to enter a note, see main manual. Profile name Enter/modify name of editable auto test profile Wire types: Propagation speed To determine the correct distance, the calculation must take into account a correction value dependent on the wire type that specifies the ratio of the pulse propagation speed in the cable to the speed of light in a vacuum (c0 = 299.792458 m/µs). For cable types, the pulse time is also specified in V/2. Minimum: 45.0 m/μs (VoP 30 %) Maximum: 149.7 m/μs (VoP 99.9 %) Default: 100.0 m/μs (VoP 66.7 %) The choice of propagation speed as V/2 or VoP is saved. Specific resistance Sets the specific resistance per kilometer Range: 40 Ω/km to 400 Ω/km Default: 353 Ω/km Specific capacitance Sets the specific capacitance per kilometer Range: 35 nF/km to 100 nF/km Default: 48 nF/km Name Enter the name of the wire type. Default: No wire type Remote kit command Remote kit command Commands s.page 85 Remote kit: Remote kit Remote kit type, s. page 83

ARGUS Copper Box 31 List of preconfigured default wire types: No. Name Wire diameter (mm) Line resistance (Ohm/km) Mutual capaci- tance (nf/km) VoP (%) Note 1 PE 0.5 AWG24 0.5 80 39 66.0 Outdoor cable, Poly- ethylene, air filled 2 PP 0.5 AWG24 0.5 80 39 66.0 Outdoor cable, Poly- propylone, air filled 3 Pulp 0.4 AWG26 0.4 150 36 60.0 Outdoor cable, conductor with pulp jacket, air filled 4 Pulp 0.5 AWG24 0.5 80 39 67.0 Outdoor cable, conductor with pulp jacket, air filled 5 Pulp 0.6 AWG22 0.6 65 38 68.0 Outdoor cable, conductor with pulp jacket, air filled 6 PIC 0.4 AWG26 0.4 150 36 64.0 Outdoor cable, conductor with plastic jacket, air filled 7 PIC 0.5 AWG24 0.5 80 39 66.0 Outdoor cable, conductor with plastic jacket, air filled 8 PIC 0.6 AWG22 0.6 65 38 67.0 Outdoor cable, conductor with plastic jacket, air filled 9 PIC 0.9 AWG19 0.9 29 34 72.0 Outdoor cable, conductor with plastic jacket, air filled 10 Jelly 0.9 AWG19 0.9 29 34 68.0 Outdoor cable, petroleum/ jelly filled cable 11 Filled 0.4 AWG26 0.4 150 36 58.0 Outdoor cable, filled 12 Filled 0.5 AWG24 0.5 80 39 60.0 Outdoor cable, filled 13 Filled 0.6 AWG22 0.6 65 38 62.0 Outdoor cable, filled 14 PTFE/Teflon 0.5 AWG24 0.5 80 39 67.0 Outdoor cable, conductor with teflon jacket 15 Wire type 15 - 80 49 66.7 default, editable 16 Wire type 16 - 80 49 66.7 default, editable 17 Wire type 17 - 80 49 66.7 default, editable 18 Wire type 18 - 80 49 66.7 default, editable 19 Wire type 19 - 80 49 66.7 default, editable 20 Wire type 20 - 80 49 66.7 default, editable

32 ARGUS Copper Box Starting auto test ARGUS in the status display. The auto test is not yet started. The default is the most recently used auto test profile, in this example Copper box auto test 1. ARGUS displays the stored notice in the preview. Starts the auto test using the selected auto test profile. ARGUS executes the tests stored in the profile in consecutive order. During the tests, you can select the respective results using the cursor keys. You can use the cursor keys to select individual test results, in this example capacitance measurement. The auto test has been executed. Screen display for selection of a wire type or auto test profile (in this example Copper Box auto test 1 and wire type 1). Opens the Copper Box menu, see page 20. Starts a new auto test.

ARGUS Copper Box 33 When the auto test is complete, the device automatically outouts a message and prompts you to save the results. After saving, ARGUS automatically swit- ches to the view of the saved measured values. Press one after another and ARGUS saves the current measurement Display of stored auto test values in device. ARGUS saves the result of the auto test to the first free storage slot in internal memory. ARGUS returns to the last selection menu without saving results.

34 ARGUS Copper Box You can display the measuring result in the form of a QR code using the number key . The results can then be transferred to other systems in csv format using a camera or a suitable QR code reader. exits QR code display and the results are displayed as plain text.

ARGUS Copper Box 35 7 Voltage measurement (U= and U~) Voltage measurement enables detection of e.g. connected accesses (such as ISDN-BRI U or POTS) and supply voltages (as for SHDSL using ZWR) and external voltages, such as a connection to another line. In AC voltage measurement, the frequency (10 - 200 Hz) is additionally displayed. This also enables identification of call switching and coupled voltages as well as carrier or power frequencies. Note that unexpected or hazardous mixed voltages or hazardous voltage peaks can occur. All voltages >200V are outside the permissible limits. See the chapter Technical data page 14 for information on measuring ranges, resolutions and accuracies of voltage measurement. Setting Voltage measurement: ARGUS in the status display. The voltage measurement is not yet started. Starts voltage measurement between sockets Tip and Ring. Hotkeys/settings Opens the Copper Box menu, see page 20. Display mode, s. page 36 Input resistance, s. page 36 Press one after another and Remote kit command, s. page 83 Remote kit, s. page 81 Information bell, s. page 36 Press one after another and Copper Box info, s. page 21 Press one after another and Store, s. page 21

36 ARGUS Copper Box Starting voltage measurement ARGUS in the status display. Continued on next page Voltage measurement starts automati- cally when the Copper Box is activated. In this example, the - Current voltage in volts - Current frequency of AC voltage in hertz - Minimum voltage in volts - Maximum voltage in volts are measured. Settings Description Display mode: Determines whether the standard display (Normal display mode) or min./max display (incl. min./max. display mode) is used. Default: Normal display Input resistance: Sets the input resistance as high-ohm or low-ohm. Default: high-ohm Information bell: Sets whether an acoustic signal sounds when a measured value is displayed. Default: off Opens the Copper Box menus, see page 20. Displays the current measured value, see page 36. The continuing measurement is paused. Displays the current measured values. Continues measuring.

ARGUS Copper Box 37 Display: - Current DC voltage in volts - Current AC voltage in volts - Current frequency of AC voltage in hertz Hotkeys/settings s. page 20 Selection of voltage measurement By default, voltage measurements are carried out using high-ohm values. A change in the input resistance is stored until ARGUS is restarted. For high-ohm measurement, the input resistance is at least 1 MΩ (depending on the measuring range). Voltage measurement can also be set to a low-ohm range. Low-ohm measure- ment is carried out using a 200 kΩ resistor connected parallel to the input impedance that is dependent on the measuring range. Low-ohm measure- ment permits discharge of coupled voltage on lines (charged lines). This load indicates the state (low-ohm, high-ohm) of the source of any external voltage. Opens the Copper Box menu, see page 20. Display of minimum and maximum measured values. Continues measuring.

38 ARGUS Copper Box The voltage measurement must be restarted for the changes to take effect. The example here shows a low-ohm (loaded) measurement. Switches the input resistance. To measure voltage using a different socket combination, see page 22. The input resistance can only be switched over during a two-pole measurement.

ARGUS Copper Box 39 Example measurements: The measured DC voltage of 48.90 V can indicate the POTS access of a PBX. Typical POTS PBX voltages are 48 V, 32 V or 24 V DC. The measured DC voltage of 96.2 V can indicate an ISDN-BRI U access. The voltage for an ISDN-BRI U access is normally between 91 V and 99 V. The measured voltage of 60.93 V could indicate an POTS access. The normal voltage range of an POTS access is between 50 V and 72 V.

40 ARGUS Copper Box Ideally, no AC voltage should be measured between individual wires. Still, AC voltages can be coupled to the wires directly via a line termination or indirectly through the air. The typical call-switching voltage can occur transiently between Tip and Ring. Display of the measurements between the Tip (a-wire) and Ring (b-wire). - Display of DC voltage in V - Display of AC voltage in V - Frequency of AC voltage in hertz You can open the measur- ing results of the wire pairs using the cursor keys. Opens the measuring results for the wire pairs.

ARGUS Copper Box 41 Example: AC voltage measurement Incoming call In this example the Copper Box is connected so as to measure the voltage of an POTS access. A typical DC voltage is measured. This example shows an incoming call. In addition to the DC voltage, we can see a call-switching voltage with the typical frequency of 25 Hz.

42 ARGUS Copper Box 8 Capacitive symmetry measurement (CSym) With the aid of capacitive symmetry measurement, it is possible to detect irregularities in the wiring that can result in signal distortions or transmission errors. The line must be open. In a real line, a network of serial and parallel capacitances is formed between the individual reference points, as illustrated the following diagram. The total capacitance Cab of the series connection of CaE and CbE is actually measured between a (tip) and b (ring). The measured value shows the mutual capacitance (Cm) value. This applies correspond- ingly for measurements between a (tip) and ground (E) and between b (ring) and ground. These measurements for the basis for calculating the actual values of Cab, CaE and CbE. The calculated values are then used in determining symmetry. Additionally, the absolute deviation of the two capacitances CaE and CbE with respect to ground and the relative deviation are determined. Relative deviation (in %) = 2x Absolute deviation (in nF) = absolute difference (CaE-CbE) The calculated values represent the actual values CaE, CbE and Cab for the individual capacitances. As the capacitances with respect to ground CaE and CbE are particularly important for the symmetry of a line, the absolute and percentage values are also given here for the sake of clarity. The relative value should not exceed 1 % (recommendation). The absolute deviation is of particular importance on extremely short lines, as even small differences here can result in a higher-percentage deviation. It must be reviewed on a case-by-case basis whether this is acceptable. The line must be open. This can be achieved e.g. using the instrument kit function "open circuit". A voltage check is performed before the measure- ment in which the voltage limits given in the table (see page 11) may not be exceeded. See the chapter Technical data page 14 for information on capacitive symmetry measurement.

ARGUS Copper Box 43 Capacitive symmetry measurement settings ARGUS in the status display. Capacitive symmetry measurement is not yet started. Hotkeys/settings of capacitive symmetry measurement s. page 20 and in the sheet under. Under certain circumstances, the capacitive symmetry measurement can abort. Possible causes include the presence of an external voltage, absence of a line or the existence of a loop. When you select the susceptibility "insecure (fast)", the red warning "ATTENTION: susceptible" appears on the display. If a wire type has been selected, this is shown in the display. Opens the Copper Box menu, see page 20. Starts capacitive symmetry measurement. Settings Description Wire types: See page 30 for an explanation of wire types. Susceptibility: Selects the susceptibility with which ARGUS performs capacitive symmetry measurement. Robust for external voltage: Insecure (fast): Default: The measurement is reliable in the event of external voltages up to 17 V. Using another measuring method, the measurement is extremely fast but much more susceptible to interference. Reliable for external voltages

44 ARGUS Copper Box Starting symmetry measurement ARGUS in the status display. Depending on the line characteristics, the measurement can take a few seconds. Display: When you select the susceptibility "Insecure (fast)", a warning appears in the display. Starts capacitive symmetry measurement. - Cm (operating (mutual) capacitance) (in nF) - Cab (capacitance between Tip and Ring) (in nF) - CaE (capacitance between Tip and Ground) (in nF) - CbE (capacitance between Ring and Ground) (in nF) - ΔC (absolute deviation between CaE and CbE) (in nF) - Relative deviation (in %) When a wire type is selected the line length is calculated, see page 45.

ARGUS Copper Box 45 When a wire type is selected the specific capacitance and measured operating capacitance are used to calculate the line length. Display: Example measurements: The capacitances CaE and CbE are very close together. The relative deviation is below 1 %. The wires are extremely homogeneous. The capacitances CaE and CbE deviate greatly. The relative deviation is signifi- cantly greater than the recommended 1 %. The wires are extremely asymmetrical. - Cm (operating (mutual) capacitance) (in nF) - Line length in km - Specific capacitance of wire type

46 ARGUS Copper Box 9 Capacitance measurement (C) Capacitance measurement shows the typical input capacitance of connected devices or the capacitance of the open line. The line must be open. This can be ensured using the instrument kit function "open circuit". Before the measurement, a voltage check is performed in which the voltage limits given in the table (see page 11) may not be exceeded. The measuring ranges, resolutions and accuracies of the capacitance measurement may be found in the chapter Technical data, see page 14. Capacitance measurement settings ARGUS in the status display. Capacitance measurement is not yet started. Hotkeys/settings of capacitance mea- surement see page 20 and in the sheet under. Once you have measured C-symmetry, you no longer need to measure capacitance. When you select the susceptibility "Insecure (fast)", the red warning "ATTENTION: susceptible" appears on the display. Opens the Copper Box menus, see page 20. Starts capacitance measurement.

ARGUS Copper Box 47 Starting capacitance measurement ARGUS in the status display. In this example, a capacitance of approx. 48 nF is measured between each of the sockets Tip/Ring and Ground. For a specific capacitance of approx. 50 nF/km, this value indicates that the line is approx. 1 km long and open. No measurement is possible on a closed line. ARGUS indicates this with the message "Loop?". Settings Description Wire types: See page 30 for an explanation of wire types. Susceptibility: See page 43 for an explanation of susceptibility. When you select the susceptibility "Insecure (fast)", the red warning "ATTENTION: susceptible" appears on the display. Starts capacitance measurement

48 ARGUS Copper Box Example measurements: In this example, a capacitance of approx. 86.51 nF is measured between the sockets Tip/Ring. Ideally, the line should be in capacitive balance. However, if the capacitance between Tip and Ground and between Ring and Ground differ by more than 2-3 %, this can indicate an asymmetry. You can investigate this hypothesis by measuring the symmetry (see Chapter 8), which delivers a much more accurate determination of symmetry. Switches to the line length parameters, see page 50.

ARGUS Copper Box 49 9.1 Calculating line length Every telecommunication cable has a certain loop resistance and operating capacitance per unit of length. As the type of cable laid is generally known, this value too is known. The values are design-related and relatively constant, as the cables are laid in the earth and subject to relatively minor temperature and humidity effects. However, a typical subscriber line can consist of multiple segments. In these segments, the wire cross-sections, and thus the technical specifications, can vary. This can only be determined for a measurement between the Tip- and Ring-wires. The measurements with respect to Ground can be subject to random influences and thus can- not be specified with a general capacitance or resistance value per unit of length. The line length calculations can then be compared with the line length, which is generally also known, thus providing information about faults. Using the calculated value, you can roughly compare the line lengths and conduct further fault-finding (e.g. with a TDR) in the event of discrepancies. A wire type must be selected to enable calculation of the line length using a C or R measurement. See page 30 for these and further settings. The wire type can be selected and configured during or after the measurement. Starting capacitance measurement. ARGUS in the status display. In this example, capacitance measure- ment is carried out with a measuring frequency of 8 Hz and the values stored for wire type 1. It is important to select a cable type (see page 31), the default is „No cable type“. Opens the Copper Box menus, see page 20. Starts capacitance measurement.

50 ARGUS Copper Box In this example, a capacitance of approx. 22.30 nF is measured between Tip/Ring. On the basis of the values stored under wire type 1, this corresponds to a 455 m line. For a two-pole measurement the measured value is displayed in real time. Example measurements: In this example, a capacitance of approx. 86 nF is measured between Tip/Ring. For a capacitance of approx. 49 nF/km, this value indicates that the line is approx. 1.77 km long. Display: Opens the Copper Box menu, see page 20. The wire type can be selected and configured during or after the measurement. Opens the Copper Box menu, see page 20. - Calculated line length of Tip/Ring in km - Specific capacitance of wire type Switches to the wire type settings.

ARGUS Copper Box 51 10 Isolation resistance measurement (Iso.) Isolation resistance measurement can indicate damage to cable isolation, moisture penetration or oxidised contact points on the line. A voltage check is performed before the measurement in which the voltage limits given in the table (see page 11) may not be exceeded. See the chapter Technical data page 14 for information on measuring ranges, resolutions and accuracies of isolation resistance measurement. Isolation resistance measurement settings ARGUS in the status display. Isolation resistance measurement is not yet started. Before the measurement, the selected test parameters are displayed. - Measuring voltage (in this example 105 V) - Measuring current (in this example max. 2 mA) - Polarity (in this example standard) Hotkeys/settings of Isolation resistance measurement s. page 20 and in the sheet under. The configuration options can vary depending on the selected sockets. Opens the Copper Box menu, see page 20. The polarity is inverted/ reversed, see page 52. Starts the isolation resistance measurement.

52 ARGUS Copper Box Settings Description Polarity: Determines whether the polarity of the measurement is inverted. Standard is selected such that e.g. a correctly connected passive test termination (PPA) is non-conducting. If the PPA is reversed due to reversed connection, the display shows the value PPA (~470 kΩ). If this occurs, reverse the polarity. Default: Standard Range limit: Sets the limiting thresholds for isolation resistance measurement (see also page 14). The measurement is only carried out up to the set threshold. The threshold applies for isolation resistance measurement when a measurement voltage of 105 V is selected. Default: 1000 MΩ Measurement voltage: Determines whether isolation measurement is to be conducted at a high 105 V or low 8 V voltage. With 8 V, it is possible e.g. to measure against a connected NTBA, so that this does not become low-ohm (above approx. 10 V) and falsify the measurement. Default: High voltage (105 V) Susceptibility: Selects the susceptibility with which ARGUS performs isolation resistance measurement. Robust for ext. voltage: Insecure (fast): Default: The measurement is reliable in the event of external voltages up to 17 V. Using another measuring method, the measurement is extremely fast but much more susceptible to interference. Reliable for external voltages Display mode: Determines whether the standard display (Normal display mode) or min./max display (incl. Min./max. display mode) is used. Default: Normal display

ARGUS Copper Box 53 Starting Isolation resistance measurement ARGUS in the status display. Isolation resistance measurement is not yet started. Current measuring polarity Opens the Copper Box menu Inverts the polarity, see page 52. Starts the isolation resistance measurement. When Isolation resistance measurement is started, a warning is displayed when a measurement voltage of 105 V is used. ARGUS generates a voltage of 105 V at the start of the measurement. Special care is necessary due to this generated voltage. Stops the test.

54 ARGUS Copper Box Example measurements: The example shows the measurement of a resistance between Tip/Ring, Tip/ Ground and Ring/Ground of >1000 MΩ. This indicates that the line is not damaged. Depending on the require- ment, a value of e.g >300 MΩ is considered good. Values <300 MΩ and >5 MΩ should be examined more closely. Values under 5 MΩ indicate an isolation fault. In this example, the measurement shows a markedly low resistance between Ring and Ground. This indicates a fault. Ideally, the values of Tip to Ground and Ring to Ground should always be in balance. A value of 470 kΩ indicates a passive test termination. The value should be verified by reversing the polarity with . Fast „Isolation resistance measurement“, e. g. of all pins at the demarcation point with respect to each other and earth. To save significant time in measuring, the measuring range was set e. g. to „2 MΩ - 500 MΩ“ and susceptibility „uncertain (fast)“ was selected. You can display val- ues outside the measuring range using (e. g. <2 MΩ or >500 MΩ). When continuously measuring with the susceptibility „Reliable for external volt- age“, the measured values cannot be updated directly after short-curcuiting the line. The measurement can repeat up to four times before the display shows a new value. Starts a new measurement.

ARGUS Copper Box 55 11 Resistance symmetry (RSym) This measurement determines the resistance symmetry of a line. Of primary importance for resistance symmetry are the two resistances Ra and Rb, i.e. the resistances of the two signal wires. To great a difference in resistance between the two wires can result in signal distortions and transmission errors. In a real line, a network of serial resistances is formed between the individual reference points, as illustrated the following diagram. The measuring loops between Tip-Ring-Ground can be realised manually or using an electronic instrument kit. Ideal measuring configuration: Values Ra, Rb and RE are not measured directly, but instead are calculated from three individual measurements (Rab, RaE, RbE). The caculated values are then used in deter- mining symmetry. RE is dependent on the measuring current here and is an auxiliary quantity. RE is gen- erally significantly less (RE << Ra reasp. Rb) than Ra or Rb. The cable shield is generally connected to ground at the main distribution frame resp. at the cable branch box. When the demarcation point is earthed, an electrical connection exists via both the cable shield and the ground connection. Always make sure that the measuring loops are properl connected to ground. If the Tip-Ring-Ground measuring loops are not earthed, the measurement cannot be con- ducted (e. g. clamping to painted, non-conducting termination frames with crocodile clips).

56 ARGUS Copper Box Special features for RE (Examples): 1a. Measuring site, e. g. demarcation point: The demarcation point is not earthed. The Copper box (GND socket) is disconnected from the shielding terminal of the demarca- tion point. The measurement works when the cbale shield os continuous. The dis- played RE measurement is the R-cable shield (Rshield). The measurement works even if e. g. a shield terminal in the earth cable becomes high-ohm due to an installa- tion error or a lightning strike. This can then be recognised from the high RE measured value. 1b.However, if the cable shield is not contin- uous (see image) or too high-ohm, the mea- surement will no longer function (RE>10 kΩ). As a remedy, the reistance symmetry mea- surement can be conducted using the build- ing potential equalisation rail or an earthed metal water or heating pipe. If this is not pos- sible either, trained electricians can, after checking the building configuration (TN-S, TT), use the PE (protective ground) line as an earthing point after verifying thar it is voltage-free. In general, attention must be paid to ensuring secure contact, particularly to oxidised or corroded earthing points. The measurement does not work when the earthing is interrupted at one of the connection points. However, it will work for a poor ground connection. Reason for cancellation of mea- surement (RE >10 kΩ).

ARGUS Copper Box 57 2. Measureing site, e. g. demarcation point: The demarcation point is not earthed. The cable shield is interrupted at the site shown in the illustration. However, the resistance symmetry measurement can still work if the cable shield at the demarcation point is con- nected to one of the earthing points shown in the picture. However, the RE measurement is not Rshield, as the shield can have an ground potential of varying quality due to the lead sleeve in the ground (obsolete constuc- tion method). The ground potential can also come from a network of building accesses (other earthed demarcation points) in the branch cable: In the main cable area, the ground potential can come from another cable branch box. In practice, a combination of the two examples is quite common. All these effects lead to varying RE measurements. 3. TAE (residence) Resistance symmetry is often faulty in the last mile, e. g. due to a poor splice (rat-tail splice, poorly crimped conductor connec- tions, loose screw connection). A measurement is possible if the last mile is a connected to a buried, continuous shield conductor this case is not illistrated). How- ever, This is seldom the case. Thus, you must either lay an auxiliary conductor, e. g. from the potential equalistion point to the measurement, or use earthed harting pipes in the residence. If does not work, trained electricians can, after checking the bulidung mains configuration (TN-S, TT), use the PE (protective ground) line as an earthing point after verifying that it voltage-free. In general, attention must be paid to ensuring secure contact, particulary to osidised or corroded earthing points. 4. If can intact conductor is used as an auxil- ilary conductor instead of ground, RE=RH, RH is then entirely on the order of magnitude of Ra and Rb. A complete twisted pair (Tip- Ring) can also be used for this.

58 ARGUS Copper Box Calculation basis: The following calculation basis is used for a 3-way measurement Rab, RaE, RbE, with R1, R2, R3 as the total resistance of the respective line pairs. Additionally, the absolute deviation of the two resistances Ra and Rb and the relative deviation are determined. Relative deviation (in %) = 2x ΔR (absolute deviation in Ω) = absolute deviation (Ra - Rb) A voltage check is performed before the measurement in which the voltage limits given in the table (see page 11) may not be exceeded. A loop must be created between Tip-Ring-Ground. This can be achieved using the instru- ment kit function "Tip-Ring-Ground". See the chapter Technical data page 14 for information on measuring ranges, resolutions and accuracies of resistance symmetry measurement.

ARGUS Copper Box 59 Resistance symmetry measurement settings ARGUS in the status display. The measurement is not yet started. Hotkeys/settings of resistance symmetry measurement s. page 20 and in the sheet under. Under certain circumstances, the resistance symmetry measurement can abort. Possible causes include the presence of an external voltage, absence of a line or of a loop. When you select the susceptibility "insecure (fast)", the red warning "ATTENTION: susceptible" appears on the display. If a wire type has been selected, this is shown in the display (in this example wire type 1). Opens the Copper Box menus, see page 20. Starts the resistance symmetry measurement. Settings Description Wire types: See page 30 for an explanation of wire types. Susceptibility: Selects the susceptibility with which ARGUS performs resistance symmetry measurement. Robust for external voltage: Insecure (fast): Default: The measurement is reliable in the event of external voltages up to 30 V. Using another measuring method, the measurement is extremely fast but much more susceptible to interference. Robust for external voltages

60 ARGUS Copper Box Starts resistance symmetry measurement ARGUS in the status display. The resistance symmetry measurement is not yet started. Depending on the line characteristics, the measurement can take a few seconds. Display: Opens the Copper Box menus, see page 20. Starts the resistance symmetry measurement. - Rs (loop resistance) (in Ω) - Ra (resistance of Tip-wire) (in Ω) - Rb (resistance of Ring-wire) (in Ω) - RE (resistance of Ground) (in Ω) - ΔR (absolute deviation between Ra and Rb) (in Ω) - Relative deviation (in %)

ARGUS Copper Box 61 When a wire type is selected, the line length is calculated from the specific resistance. Display: Example measurements: The resistances Ra and Rb are very close together. The relative deviation is below 1 %. The wires are extremely homogeneous. The resistances Ra and Rb deviate greatly. The relative deviation is consider- ably above the recommended 1 %. The wires are extremely asymmetrical. - Rs (sum of loop resistances) (in Ω) - Ra (resistance of Tip-wire) (in Ω) - Rb (resistance of Ring-wire) (in Ω) - Line length in km - Specific resistance of the selected wire type

62 ARGUS Copper Box 12 Loop resistance measurement (R) Loop resistance measurement enables you e.g. to detect short-circuits and estimate line lengths, among other things. A voltage check is performed before the measurement in which the voltage limits given in the table (see page 11) may not be exceeded. A loop must be created. This can be ensured using the instrument kit function "short circ. Tip-Ring-Ground". Loop resistance measurement is not intended for single-wire deter- minations. Use resistance symmetry measurement for this purpose, see page 55. See the chapter Technical data page 14 for information on measuring ranges, resolutions and accuracies of loop resistance measurement. Loop resistance measurement settings ARGUS in the status display. The loop resistance measurement is not yet started. Loop resistance is always measured continuously. Hotkeys/settings of loop resistance mea- surement see page 20 and in the sheet under. When you select the susceptibility "Insecure (fast)", the red warning "ATTENTION: susceptible" appears on the display. Opens the Copper Box menus, see page 20. Starts loop resistance measurement.

Default: off 12 Loop resistance measurement (R) ARGUS Copper Box 63 Settings Description Wire types: See page 30 for an explanation of wire types. Susceptibility: Selects the susceptibility with which ARGUS performs loop resistance measurement. Robust for external voltage: Insecure (fast): Default: The measurement is reliable in the event of external voltages up to 3.5 V DC and 30 V AC. Using another measuring method, the measurement is extremely fast but much more susceptible to interference. Robust for external voltages Display mode: Determines the normal display (current measured value) or min./max display (min./max. values) is used. Default: Normal display

64 ARGUS Copper Box Starts loop resistance measurement ARGUS in the status display. The loop resistance measurement is not yet started. In this example, a loop resistance of 420 Ω is measured. To perform a loop resistance measurement using another socket combination, see page 22. Loop resistance measurement can also return no result (---) e.g. due to excessive influence. The polarity is reversed up to 20 kΩ. Opens the Copper Box menus, see page 20. Starts loop resistance measurement. Display of minimum and maximum measured values. The continuing measurement is paused, see also page 36.

ARGUS Copper Box 65 Example measurements: The example shows a measurement of 458 Ω. For a copper cable with a specific resistance of 160 Ω / km, this indicates a short-circuited twisted pair with a length of 1.43 km. As an explanation, the line can be deliberately shorted at one end, or is unintentionally shorted due to a fault in an unknown location. A large value such as 20 MΩ or >40 MΩ indicates that no line loop (intentional shorting) has been set up. Loop resistance cannot be measured then. 12.1 Calculating line length See page 49 for calculation of line length using the R-values.

66 ARGUS Copper Box 13 DC current measurement (I=) DC current measurement enables detection e.g. of feeds, emergency feeds or line terminations. Before measuring, make sure that the Copper Box is connected in the circuit in series. The measuring range, resolution and accuracy of DC current measurement are described in the chapter Technical data, see page 14. DC current measurement settings ARGUS in the status display. The current measurement is not yet started DC voltage is always measured continu- ously. Hotkeys/settings of current measure- ment s. page 20 and in the sheet under. Opens the Copper Box menus, see page 20. Starts loop current measurement.

values) is used. Default: Normal display Information bell: Select whether an acoustic signal sounds when a measured value is displayed. Default: off 13 DC current measurement (I=) ARGUS Copper Box 67 Starting DC current measurement ARGUS in the status display. The DC current measurement is not yet started. In this example, a DC current of 57.5 mA is measured. To measure DC voltage using a different socket combination, see page 22. Opens the Copper Box menu, see page 20. Starts the DC current measurement. Display of minimum and maximum measured values. The continuing measurement is paused, see also page 36.

68 ARGUS Copper Box 14 Longitudinal conversion loss (LCL) LCL measurement (asymmetry attenuation) looks at the balance between the Tip-wire with respect to Ground (GND) compared to the Ring-wire with respect to Ground. In this measurement, a tone is fed symmetrically to the wires with respect to Ground at 1 MHz. If a difference can be measured between the two wires, an asymmetry is present. A voltage check is performed before the measurement in which the voltage limits given in the table (see page 11) may not be exceeded. The length of the measuring leads can significantly affect the measurement, so you should always perform your measurements using the original accessories. The measuring ranges, resolutions and accuracies of the LCL measurement are set out in the chapter Technical data, see page 14. LCL measurement settings ARGUS in the status display. The LCL measurement is not yet started. Hotkeys/settings of LCL measurement see page 20 and in the sheet under. Opens the Copper Box menu, see page 20. Starts the LCL measurement.

values) is used. Default: Normal display Information bell: Selects whether an acoustic signal sounds when a measured value is displayed. Default: off 14 Longitudinal conversion loss (LCL) ARGUS Copper Box 69 Starting LCL measurement ARGUS in the status display. The LCL measurement is not yet started. In this example, an asymmetry attenuation of 54.1 dB is measured. It is not possible to change the socket combination for LCL measurement. Opens the Copper Box menu, see page 20. Starts LCL measurement. Display of minimum and maximum measured values. The continuing measurement is paused, see also page 36.

70 ARGUS Copper Box Example measurements: If the two wires are symmetric, i.e. identi- cal in their mechanical properties, a max. value is measured (in this exam- ple >65 dB). Such a high value can only be expected in ideal situations or in the event of a short circuit between Tip and Ring or an extremely short open line. A value greater than 65 dB means that the result is above the measuring range. However, a value >40 dB (as in this example 41.5 dB) is considered suffi- ciently symmetric. If a value <40 dB is measured, or even 7.8 dB as in this example, Tip or Ring may be shorted to Ground.

ARGUS Copper Box 71 15 Near-end crosstalk (NEXT) ARGUS generates a 1 MHz tone on line pair 1 and measures the crosstalk on the adjacent line pair 2, which can cause severe performance issues for DSL. A customer's line can pass through multiple segments. In this case, the measurement must be performed segment by segment, and different line pairs may need to be used as the measuring lines. A voltage check is performed before the measurement in which the voltage limits given in the table (see page 11) may not be exceeded. The length of the measuring leads can significantly affect the measurement, so you should always perform your measurements using the original accessories. The measuring ranges, resolutions and accuracies of NEXT measurement are set out in the chapter Technical data, see page 14. Connection example (towards to the customer): * Measurement is also possible from the street cabinet towards the customer (segment by segment). Connection example (towards to the MDF): * Measurement is also possible from the street cabinet towards the MDF (segment by segment).

72 ARGUS Copper Box NEXT measurement settings ARGUS in the status display. The NEXT measurement is not yet started. Hotkeys/settings of NEXT measurement see page 20 and in the sheet under. Settings Description Displaymode: Determines the normal display (current measured value) or min./max display (min./max. values) is used. Default: Normal display Information bell: Selects whether an acoustic signal sounds when a measured value is dispalyed. Default: off Opens the Copper Box menu, see page 20. Starts the DC current measurement.

ARGUS Copper Box 73 15.1 Starting NEXT measurement ARGUS in the status display. The NEXT measurement is not yet started. The NEXT measurement is started. In this example, a crosstalk attenuation of 23.7 dB is measured. It is not possible to change the socket combination for NEXT measurement. Opens the Copper Box menu, see page 20. Starts NEXT measurement. Display of minimum and maximum measured values. The continuing measurement is paused, see also page 36.

74 ARGUS Copper Box Example measurements: If there is no crosstalk between line pair 1 and line pair 2 (adjacent line), a maximum value is reached (in this example 65 dB). However, a value >37 dB (as in this example 37.7 dB) considered sufficient. The crosstalk to the adjacent line is tolerable. If a value <37 dB is measured, or even 5.8 dB as in this example, there may be a short between the two wire pairs. The tone is 100 % cross-coupled and severely interferes with the line.

ARGUS Copper Box 75 16 Signature detection/termination detection Signature detection makes it possible to detect e.g. a passive test termination (PPA). A voltage check is performed before the measurement in which the voltage limits given in the table (see page 11) may not be exceeded. Signature PTT PTT (inverted) Circuit diagrams: Starting signature detection ARGUS in the status display. Signature detection is not yet started. Opens the Copper Box menu, see page 20. Starts signature detection.

76 ARGUS Copper Box Signature detection can take a few seconds. In this example, a passive test termina- tion (PPA) was detected between Tip and Ring. See the table on page 77 for possible results. In this example, a PPA and a signature circuit between Tip and Ring were detected. Stops the test. Starts a new signature detection. Starts a new signature detection.

ARGUS Copper Box 77 16.1 Possible results Test Possible results Characteristic features Remark PPA PPA detected PPA inverted detected PPA with reversed polarity (inverted) detected. Multiple PPAs? Potentially multiple PPAs connected in parallel detected. Multiple inv. PPAs? Potentially multiple PPAs with reversed polarity (inverted) con- nected in parallel detected. 2x PPA/Iso fault? Potentially double PPA antiparallel detected or isolation fault. Signature Signature detected Signature circuit detected. Signature? Signature possibly present: External voltage, isolation resistance or additional connected devices can influence detection such that an unambiguous result is no longer pos- sible. Unknown termination Cp >500 nF Unknown termination: Cancellation, as no further detection is possible, e.g. NTBA connected, extremely long line. Other No termination detected Loop? R <8 kΩ Cancellation, as no further detection possible. Isolation fault? Rp <1 MΩ Cancellation, as no further detection possible.

ARGUS Copper Box 79 17 Fast cable check The fast cable check checks the correctness of a three-pole connection (Tip/Ring/Ground) against a loop, in other words whether Tip/Ring/Ground is properly connected for subse- quent tests. To achieve this, the cable check measures the resistance. All values below a threshold of 10 kΩ, are interpreted as a loop, and all values greater as an open line. The cable check can be performed as a standalone test or as part of the auto test. In auto test, an audible alarm sounds when a fault is detected and the auto test sequence is stopped. The loop between Tip/Ring/Ground can be realised manually or using an electronic instrument kit. Starting cable check ARGUS in the status display. The cable check is not yet started. Hotkeys/settings of cable check see page 20. Opens the Copper Box menu, see page 20. Starts the cable check.

80 ARGUS Copper Box 17.1 Test Possible results Remark Line Line OK Line pair connected correctly Line open Line pair not connected correctly, e.g. open. Possible results Opens the Copper Box menu, see page 20. Starts the cable check. Starts a new cable check.

ARGUS Copper Box 81 18 Remote kit control (Rem.) The Copper Box remote instrument kit control (Rem.) function enables ARGUS to control commonly available electronic instrument kits, such as the TX915/916. Before using the remote control function, make sure that the voltage limits specified in the table on page 11 are not exceeded during the measurement. Remote control of other electronic instrument kits that may offer additional functoins is only possible using the commands listed below. Settings Description Remote kit type TX91x + 900/905 remote The common and extended 900/905 remote commands can be acessed in the menu. When a common command is selceted, both control conmands are transmitted. In the extended 900/905 remote commands, only these control commands are transmitted, and the acknowledgement evaluated. TX91x (orange) The menu offers only the TX commands, and only the TX control commands are transmitted. 900/905 remote (blue) The menu offers all 900/905 remote commands, only these commands are transmitted and the achnowledgement evaluated.

82 ARGUS Copper Box Starting remote kit control ARGUS in the status display. In this example, the command "Exchange connect" is selected. Confirm the command. The command "Exchange connect" is sent to the remote unit. Opens the Copper Box menu, see page 20. Selects the command for remote kit control.

ARGUS Copper Box 83 The command has been sent to the remote unit. Commands: Description: Short circuit a/T-b/R The instrument kit short-circuits the Tip and Ring wires, e.g. for loop resistance measurement. Exchange connect The instrument kit switches the line through. On a DSL access for example directly to the DSLAM. Short circuit a/T- b/R-/GND The instrument kit shorts Tip, Ring and Ground, e.g. for resistance symmetry measurement. Open circuit The instrument kit opens a line, e.g. for a capacitance measurement. Tone mode The tone generator in the instrument kit is activated. The tone can be followed. Port 1 loop 3 sec. (90x) The instrument kit type 900/905 creates a loop on port 1 for 3 sec. Port 1+3 connect (90x) The instrument kit type 900/905 connects port 1 with port 3. P1+2 & 3+4 connect (90x) The instrument kit type 900/905 connects port 1 with port 2 and port 3 with port 4. Port 1+4 connect (90x) The instrument kit type 900/905 connects port 1 with port 4. Port 1+4 loop (90x) The instrument kit type 900/905 creates a loop (short-circuit) between port 1 and port 4. Port 4 loop 3 sec. The instrument kit type 900/905 creates a loop on port 4 for 3 sec. Port 2+4 connect (90x) The instrument kit type 900/905 connects port 2 with port 4. Port 3+4 connect (90x) The instrument kit type 900/905 connects port 3 with port 4 Selects and sends a new command.

19 Appendix A) Abbreviations Characters @ at Ω Ohm (unit of electrical resistance) ΔC Absolute deviation between CaE and CbE ΔR Absolute deviation between Ra and Rb A a a-wire (tip) A Ampere APL APL (German) copper line termination point B b b-wire (ring) C C 1. Celsius 2. Capacitance Cm Operating capacitance (mutual capacitance) Cp Parallel capacitance csv File format (comma-separated values) CSym Capacitive symmetry D D Germany dB Decibel DE Deutsch (German) DIN Deutsches Institut für Normung - German Institute for Standardization DSL Digital Subscriber Line DSLAM Digital Subscriber Line Access Multiplexer E E Ground (earth) EC European Community EMC Electromagnetic compatibility EN European standard F F Farad (unit of electrical capacitance) G g Gram GND Ground (earth) H Hz Hertz (unit of frequency)

I I Electric current IDC DC current ISDN Integrated Services Digital Network Iso. Isolation resistance measurement L LCL Longitudinal conversion loss M m Meter max Maximum min Minimum N NEXT Near-end crosstalk NTBA Network termination for ISDN basic rate access O opt. Optional P PPA Passive test termination Pol. Polarity POTS Plain Old Telephone Service (PSTN) Q QR Quick response R R 1. Resistance (electrical resistance) 2. Ring (b-wire) Ra Resistance a-wire Rb Resistance b-wire Rem. Remote (instrument kit control) RC Resistance (R) and capacitance (C) RE Ground resistance Ri Internal resistance Ring b-wire RoHS Restriction of Hazardous Substances Rs Loop resistance RSym Resistance symmetry S S/N Serial number SHDSL Single-Pair High-speed Digital Subscriber Line Sig. Signatures Sym Symmetry T

T Tip (a-wire) TAL Subscriber line TDR Time domain reflectometry TRG Tip, Ring, Ground U U Voltage UAC AC voltage UDC DC voltage USB Universal Serial Bus V V Volt V/2 Pulse propagation time VoP Velocity of propagation Vpp Volts Peak-to-peak W WEEE Waste Electrical and Electronic Equipment

B) Software licenses The ARGUS firmware contains code from open-source packages published under a variety of licenses (GPL, LGPL, MIT, BSD, etc.). Additional information can be found on the CD-ROM included with your device (where ordered, see Software_License.htm) or on the internet at: http://www.argus.info/web/download/Software_License. If you are interested in the sources listed under GPL/LGPL, please contact [email protected]. intec Gesellschaft für Informationstechnik mbH will provide you with a machine-readable copy of the source texts for a nominal fee to defray the costs of the physical copying process. This offer is valid for 3 years. intec Gesellschaft für Informationstechnik mbH Rahmedestr. 90 D-58507 Lüdenscheid Tel.: +49 (0) 2351 / 9070-0 Fax: +49 (0) 2351 / 9070-70 www.argus.info/en [email protected]

C) Index A Abbreviations ................................................................................................................ 84 Alarm tones ................................................................................................................... 23 Appendix ....................................................................................................................... 84 ARGUS Dimensions ........................................................................................................... 13 Inputs and outputs ................................................................................................ 13 Weight ................................................................................................................... 13 Asymmetry attenuation ................................................................................................. 68 C Calculating line length ............................................................................................. 49, 65 Capacitance measurement ........................................................................................... 46 Capacitance measurement examples .......................................................................... 47 Capacitance measurement settings ................................................................. 43, 46, 51 Capacitive symmetry example measurements ............................................................. 45 Capacitive symmetry measurement ............................................................................. 42 Changing socket assignment ........................................................................................ 22 Configuring accesses ................................................................................................... 17 D DC current measurement ............................................................................................. 66 Declaration of conformity .............................................................................................. 13 default wire types .......................................................................................................... 31 Device specifications .................................................................................................... 13 DIN EN 50419 ............................................................................................................... 12 Disposal ........................................................................................................................ 12 E Electromagnetic compatibility ....................................................................................... 13 ElektroG ........................................................................................................................ 12 EN60950-1 .................................................................................................................... 13 Example isolation resistance measurements ............................................................... 54 Example resistance symmetry measurements ............................................................. 61 F Fast cable check ........................................................................................................... 79 H Humidity ........................................................................................................................ 13 I Index ............................................................................................................................. 88 Input resistance ............................................................................................................ 38 Instructions for use ......................................................................................................... 9 Instrument kits .............................................................................................................. 81 intec Gesellschaft für Informationstechnik mbH ....................................................... 6, 87 Introduction ..................................................................................................................... 4 Isolation resistance measurement ................................................................................ 51 L LCL ............................................................................................................................... 68

89 LCL measurement examples .........................................................................................70 Loop resistance measurement ......................................................................................62 Loop resistance measurement examples ......................................................................65 M Measurement voltage ....................................................................................................52 Measuring accuracies ....................................................................................................14 N NEXT .............................................................................................................................71 NEXT example measurements ..............................................................................................................................74 O Operating temperature ..................................................................................................13 P Polarity ...........................................................................................................................52 PPA ...............................................................................................................................76 R Range limit .....................................................................................................................52 Resistance symmetry ....................................................................................................55 Return of old equipment ................................................................................................12 Rights ..............................................................................................................................2 RoHS conformity ...........................................................................................................13 RoHS Directive ..............................................................................................................12 S Safety information ............................................................................................................7 Saves the results ...........................................................................................................33 Selecting and activating the Copper Box .......................................................................18 Signature detection ..................................................................................................75, 79 Software licenses ..........................................................................................................87 Special instructions for individual measurements ..........................................................10 Capacitance ..........................................................................................................10 DC current .............................................................................................................10 Isolation resistance ................................................................................................10 Longitudinal conversion loss/NEXT .......................................................................10 Loop resistance .....................................................................................................10 Signature detection/remote kit control ...................................................................10 Voltage ..................................................................................................................10 Specifications ..................................................................................................................7 AC voltage ...............................................................................................................7 Capacitance measurement .....................................................................................7 DC current ...............................................................................................................7 DC voltage ...............................................................................................................7 Isolation resistance measurement ...........................................................................7 Longitudinal conversion loss ...................................................................................7 Loop resistance .......................................................................................................7 Near-end crosstalk (NEXT) .....................................................................................7 Start symmetry measurement .......................................................................................25 Starting capacitance measurement .........................................................................43, 47 Starting DC current measurement .................................................................................67

Starting isolation resistance measurement ....................................................................53 Starting symmetry measurement ...................................................................................32 Starts capacitance measurement. .................................................................................59 Starts loop resistance measurement .............................................................................63 Storage temperature ......................................................................................................13 Support ......................................................................................................................6, 87 Susceptibility ..................................................................................................................43 T Technical features ...........................................................................................................5 U User safety ....................................................................................................................13 Using the ARGUS Copper Box ......................................................................................18 V Version ............................................................................................................................1 Voltage measurement examples ...................................................................................39 Voltage thresholds .........................................................................................................11 W Website ......................................................................................................................6, 87 WEEE ............................................................................................................................12 Wire types ......................................................................................................................30