Aqua Creek Products Mighty Voyager Instruction Manual

Revised 10/21/20 Basic Troubleshooting Problem: The lift won’t move. Solution: Check the ends of the cords for corrosion or damage. The cord plugs should be recessed into the outlet. You should feel them pop into place when they are correctly inserted. 1. Make sure the cords are properly plugged in: NOT Properly Inserted: The cord plug is flush with or sticking out of the outlet Properly Inserted: The cord plug is recessed into the outlet 2. Check the contact points: Make sure the contact point of the control box and the battery are n ...

Revised 10/21/20 PROCEDURE BEFORE EACH USE DAILY WEEKLY MONTHLY Check battery level indicator on control box  Run the lift through a complete test cycle (fully extend actuator) to verify it is functioning properly  Wash lift with fresh water and dry with clean, soft, non-abrasive cloth  Recharge battery  Visually inspect lift for damage, corrosion, and loose or missing hardware  Check all contact points for damage and/or corrosion  Repair, clean, and apply dielectric grease to all contact points  Thoroughly clean li ...

Revised 10/21/20 Mighty Voyager Assembly Instructions NOTE: Assembly will require eighteen (18) 50lb bags (900lbs) of sand, not supplied with the lift. DO NOT USE LIFT WITHOUT SAND AS A COUNTERWEIGHT! DO NOT USE ANY MATERIAL OTHER THAN SAND AS A COUNTERWEIGHT! 1. Remove the lift from the packaging. Slide the chair and chair cradle through the bottom of the head casing and attach using the supplied snap pin. Slide the footrest assembly into the chair tube and attach using the supplied knob screw (be sure the plastic insert is fully i ...

Revised 10/21/20 Mighty Voyager Parts List Item # QTY PART # DESCRIPTION 1 1 VGR-CRT-00 VOYAGER CART ASSEMBLY 2 1 VGR-LFT-00 VOYAGER LIFT ASSEMBLY 3 1 MTY-900-00 MOTOR ASSEMBLY 4 2 BSH 10 X 3/8 #10-24 X 3/8 SOCKET HEAD CS 5 2 WF 10 #10 FLAT WASHER 6 4 BHW 1/4 X 3/8 1/4-20 X 3/8 HEX WASHER HEAD 7 1 94751A785 EXTERNAL RETAINING RING 8 1 INV01703 1” CLAMP ON SHAFT COLLAR 9 1 BEARING, ROLLER LM67048 ROLLER BEARING & RACE 10 1 K50X55X20H NEEDLE BEARING 11 1 93576A250 SPIRAL EXTERNAL RETAINING RING 12 1 F-MTMC MOTOR COVER 13 1 P-BBT-00 BALL ...

Revised 10/21/20 Mighty Voyager Assembly Instructions NOTE: Assembly will require eighteen (18) 50lb bags (900lbs) of sand, not supplied with the lift. DO NOT USE LIFT WITHOUT SAND AS A COUNTERWEIGHT! DO NOT USE ANY MATERIAL OTHER THAN SAND AS A COUNTERWEIGHT! 1. Remove the lift from the packaging. Slide the chair and chair cradle through the bottom of the head casing and attach using the supplied snap pin. Slide the footrest assembly into the chair tube and attach using the supplied knob screw (be sure the plastic insert is fully i ...

Revised 10/21/20 Installation: ADA Guidelines ADA REQUIREMENTS: The Mighty Voyager Lift is completely ADA compliant when installed correctly. The installation must meet the following requirements: • Clear deck space dimensions (see FIGURE 1) • Centerline of seat 16 inches minimum from the pool edge • Deck slope no greater than 1:48 • The seat must go at least 18 inches into the water. The lift should be installed at a location with 44 inches to 48 inches of depth (deck to pool fl oor) *Setback distance will vary on curved walls, ...

Revised 10/21/20 CAUTION! PINCH POINT AREA! LIFT TO BE STICKERED ON EACH ARM! CAUTION! PINCH POINT AREA! LIFT TO BE STICKERED ON INSIDE FACE OF ARM! Pinch Point Locations 11 ...

Revised 10/21/20 Basic Troubleshooting Problem: The lift won’t move. Solution: Check the ends of the cords for corrosion or damage. The cord plugs should be recessed into the outlet. You should feel them pop into place when they are correctly inserted. 1. Make sure the cords are properly plugged in: NOT Properly Inserted: The cord plug is flush with or sticking out of the outlet Properly Inserted: The cord plug is recessed into the outlet 2. Check the contact points: Make sure the contact point of the control box and the battery are n ...