Celexon PS Ultraflat Manual 

universal PS Ultraflat Thank you for purchasing a celexon ceiling mount. Please read the instructions carfully and ensure that the mount is suitable for your projector prior to installation. Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! celexon. TM Gutenbergstraße 2 48282 Emsdetten www.celexon.com SKU: 1091279

and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor. • This mounting bracket was designed to be installed and utilised ONLY as specifi ed in this manual. Improper installation of this product may cause damage or serious injury. • This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual. • Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. • Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. • Tighten screws fi rmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power. • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Important: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement. Note: Read the entire instruction manual before you start installation and assembly. ceilingplate (x1) projector plate assembly (x1) B safe cover (x4) C padlock (x1) D ceilingplate (x1) projector plate assembly (x1) B adapter bracket (x1) E M-J M-L Use the padlock in the locking plate and then fi x the locking plate with a screw to prevent the projector plate assembly rocking in use. Pitching Angle Adjustment Adjust to the desired angle. Maintenance • Check that the bracket is secure and safe to use at regular intervals(at least every three months). • Please contact your distributor if you have any questions. 6 1

C Insert the four safe covers into the arms of adapter bracket till they fi t mounting hole pattern. Use four screws to fi x the safe covers and tighten all screws with a proper screwdriver. Hanging the Bracket onto the Ceiling Plate Carefully guide the projector bracket with the four screws into the keyhole opening, slowly turn the projector bracket clockwise into place. For Solid Brick and Concrete Mounting Drill three pilot holes Package M M3x25 (x4) M4x25 (x4) M5x25 (x4) M6x25 (x4) M-A M-B M-C M-D D4 washer (4x) D6 washer (x4) M5x8 (x4) M8x20 (x1) M-E M-F M-G M-H ø12xø6x13 (x4) 4mm allen key (x1) 6mm allen key (x1) M5x10 (x1) M-I M-J M-K M-L Package W ST6.3x50 (x3) concrete anchor (x3) D6 washer (x3) W-A W-B W-C 2 5

plate onto the ceiling WARNING Installer must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. Installing the Projector Plate Assembly M-H M-K M-J Attach the projector plate assembly to the ceiling plate using the supplied screw. It is necessary to loosen or tighten the adjust screws with an Allen key according to the weight of the projector installed. Installing the Adapter Bracket Place the projector bracket as close as possible to the projector‘s center of gravity. Position the holes of arms over the mounting holes. Arm Make sure three point in a line to help with screwing the safe covers. M-I M-A M-B M-C M-D M-E M-F Note: If there are only three mounting holes using three arms of adapter bracket. Important: If the projector does not have at least three mounting holes, do not use this adapter bracket. Screw the adapter bracket onto the projector. TIGHTEN ALL SCREWS BUT DO NOT OVER TIGHTEN! 4 3