Advantech PPC-MB-610 Startup Manual

Before card installation, please ensure that the following items have been included in your shipment: 1. 1 x PPC-MB-610 mini-ITX motherboard 2. 1 x COM cables (1 to 4 port DB9) 3. 1 x SATA cable 4. 1 x PPC-MB-610 startup manual 5. 1 x Warranty card 6. 1 x Thermal grease 7. 14 x COM port screws 8. 2 x M.2 packet screws If any of these items are missing or damaged, contact your distributor or sales representative immediately. Note 1: � For�detailed�PPC-MB-610�specifications,�refer� to the latest product information provided on the Advantech website (PPC-61X1C model). Note 2: � Acrobat�Reader�is�required�to�view�PDF�files.The� Acrobat Reader software can be downloaded from www.adobe.com/Products/acrobat/read- step2.html (Acrobat is a trademark of Adobe). PPC-MB-610 Mini-ITX Motherboard with Intel® Core™ i7/ i5/i3/Pentium®/Celeron® LGA 1151 CPU, DP/VGA, 5 COM, 6 USB, Dual LAN, PCIe x 16, and M.2 M Key & E key Startup Manual 1. Insert the memory module into the memory slot at a 45 degree angle, as shown below. Ensure that the gold fingers�of�the�module�are�fully�inserted�into�the�slot. 2. Once inserted, gently press the memory module into the slot until the tabs snap into place, securing the module in position. 45° Installation Guide Packing List For more information about this or other Advantech products, visit our website at http://www.advantech.com For technical support and service, visit our support website at http://support.advantech.com This manual is for PPC-MB-610, Rev. A1. Part No. 2043776000 Printed in China Edition 1 July 2020

Selected M/B PPC-MB-610 CPU CPU i7-8700/i7- 8700T i5-8500/i5- 8500T i3-8100/i3- 8100T Pentium G5400/ G5400T Celeron G4900/ G4900T i7- 9700TE i5-9500E/ i5-9500TE i3-9100E/ i3-9100TE Core NO. 6/6 6/6 4/4 2/2 2/2 8 6/6 4/4 Max Speed 3.2GHz(up to 4.6GHz) / 2.4 GHz(up to 4.0GHz) 3.0GHz(up to 4.1GHz) / 2.1 GHz(up to 3.5GHz) 3.6/3.1 GHz 3.7 / 3.1 GHz 3.1 / 2.9 GHz 1.8 GHz(up to 3.8GHz) 3.0GHz(up to 4.2GHz)/ 2.2 GHz(up to 3.6GHz) 3.1GHz(up to 3.7GHz)/ 2.2 GHz(up to 3.2GHz) L3 Cache 12 / 12 MB 9 / 9 MB 6 / 6 MB 4 / 4 MB 2 / 2 MB 12 MB 9/9 MB 6/6 MB TDP 65 / 35 W 65 / 35 W 65 / 35 W 54 / 35 W 54 / 35 W 35 W 65/35 W 65/35 W Chipset Q370 Memory 2 x 260-pin SODIMM DDR4 , 2666 MHz , up to 32 GB ( non-ECC ) Network (LAN) 2 x 10/100/1000 Mbps Ethernet and 1 x intel® L219LM (support AMT 12.0 only for i7 & i5) , 1 x Intel i211 Rear I/O 1 x RS232/422/485 , 1 x RS232 , 1x DP1.2 , 1 x VGA , 6 x USB3.1 , 1 x Line-out , 1 x Mic-in Internal Connector 3 x RS232 , 1 x GPIO ( 8 channels ) , 2 x speaker , 1 x LED , 2 x USB 2.0 , 1 x LVDS , 1 x touch control , 2 x SATA 3.0 ( support RAID 0,1 ) , 1 x LPC (to support TPM2.0) , Watchdog Timer 255�timer�intervals�,�configurable�using�software Expansion "1 x M.2 slot(2280 M key) for storage; 1 x M.2 slot (2230 E key) for wireless 1 x PCIex16 slot for riser card" Dimensions (W x H) 170 mm x 170 mm (6.69" x 6.69") OS Support Microsoft® Windows 10 ( 64 bit ), Linux Specifications

The PPC-MB-610 motherboard features a number of jumpers�that�allow�users�to�configure�the�system�according� to�specific�applications.�The�functions�of�each�jumper�and� connector are listed in the table below. Connector and Headers Connectors and Headers List Label Function CN2 Mic-In/Line-Out connector LAN2_USB1 RJ45+USB 3.1 stack connector LAN1_USB1 RJ45+USB 3.1 stack connector VGA1 VGA display connector DP1 DisplayPort connector COM12 COM 1/2 connector USB3 USB 3.1 x2 connector ATX12v1 ATX 12V power supply connector CN21 ATX Power Supply Connector CN5 Power button connector CN6 COM 3/4/5 and GPIO connector BAT1 Battery connector SPI1 SPI�BIOS�flash�socket CN16 Touch connector CN17 LVDS panel connector CN20 LVDS backlight inverter power connector Sysfan1 ~ 2 System fan power connector CPUFAN1 CPU fan power connector SATA1 ~ 2 SATA signal connector CN4 Power LED connector CN9/CN12 2 x USB 2.0 pin header PCIEX16_1 PCIe x 16 slot connector AMP1 Audio�amplifier�output�connector DIMMA1/ DIMMB1 DDR4 SODIMM socket CPU1 CPU socket M.2_2 M.2 E-Key NGFF1 M.2 M Key COM12: COM 2 Connector Pin Definition (RS232) Definition (RS422) Definition (RS485) 1 DCD TX- TX RX- 2 RXD TX+ TX RX+ 3 TXD RX+ 4 DTR RX- 5 GND 6 DSR 7 RTS 8 CTS 9 RI CN6:COM 3/4/5 and GPIO connector 1 COM3_DCD# 2 COM3_DSR# 3 COM3_RXD 4 COM3_RTS# 5 COM3_TXD 6 COM3_CTS# 7 COM3_DTR# 8 COM3_RI# 9 GND 10 GND 11 COM4_DCD# 12 COM4_DSR# 13 COM4_RXD 14 COM4_RTS# 15 COM4_TXD 16 COM4_CTS# 17 COM4_DTR# 18 COM4_RI# 19 GND 20 GND 21 COM5_DCD# 22 COM5_DSR# 23 COM5_RXD 24 COM5_RTS# 25 COM5_TXD 26 COM5_CTS# 27 COM5_DTR# 28 COM5_RI# 29 GND 30 GND 31 GND 32 SIO_GPIO6 33 SIO_GPIO4 34 SIO_GPIO2 35 SIO_GPIO0 36 SIO_GPIO7 37 SIO_GPIO5 38 SIO_GPIO3 39 SIO_GPIO1 40 +V5_DUAL Jumpers and Connectors (Cont.) Jumpers and Connectors

Jumper Settings Jumpers List Jumper Function JP1 ATX/AT select JCMOS1 RTC select JP2 Touch power select JP3 LCD power select JP4 Enable power select JP5 LVDS PWM power select JP6 COM Pin 9 power select (COM 1 and 2) JP7 LVDS resolution select ATX/AT Select (JP1) (1-2) P1 AT (2-3) P2 ATX (default) P1 P2 RTC Select (Jcmos1) (1-2) P3 Normal (default) (2-3) P4 Clear CMOS P3 P4 CN16: Touch Connector Pin Definition 1 Y+ 2 X+ 3 SENSE 4 Y- 5 X- Sysfan 1 ~ 2: System Fan Power Connector Pin Definition 1 GND 2 POWER 3 SPEED 4 PWM CPUFAN1: CPU Fan Power Connector Pin Definition 1 GND 2 POWER 3 SPEED 4 PWM CN4: Power LED Connector Pin Definition 1 +V5_DUAL 2 +V5 3 GND 4 GND AMP1: Audio Amplifier Output Connector Pin Definition 1 SPK L- 2 SPK L+ 3 SPK R+ 4 SPK R- Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)

Touch Power Select (JP2) (1-2) P5 connect resistive touch screen(default) NC P6 not connect resistive touch screen P5 P6 LCD Power Select (JP3) (1-2) P7 +V5 (2-3) P8 +V3.3 (default) P7 P8 Enable Power Select (JP4) (1-2) P9 +V5 (2-3) P10 +V3.3 (default) P9 P10 LVDS PWM Power Select (JP5) (1-2) P11 +V5 (2-3) P12 +V3.3 (default) P11 P12 Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.) COM Ring Select (JP6) (1-3)/(2-4) P13/P14 COM 2/1 ring (default) (3-5)/(4-6) P15/P16 COM 2/1 5V (7-9)/(8-10) P17/P18 COM 2/1 12V P13 P14 P15 P16 P17 P18 LVDS Resolution Select (JP7) (1-2)/(5-6)/ (7-8) P19 1024*768 (24 bit) (for PPC-6151C chassis) (1-2)/(7-8)P20 1280*1024 (24 bit) (for PPC- 6171C chassis) (3-4)/(7-8) P21 1280*1024 (24 bit) (for PPC- 6191C chassis) P19 P20 P21

Board Layout: Jumper and Connector Locations USB3 COM12 DP1 VGA1 LAN1_USB1 LAN2_USB1 CN2 AMP1 CN4 PCIE X 16 CN9 CN12 DIMMA1 DIMMB1 SYS FAN2 SYS FAN1 CPU FAN1 CN20 JP3 JP4 JP5 CN17 JP2 CN16 JP1 JP7 CN21 ATX12V1 CN22 SATA1 SATA2 SPI1 CN6 CN5 BAT1 JP6 JCMOS1 CPU1 M.2_2 NGFF1

1.1 Entering the BIOS Setup Utility When the power is turned on, press the button to enter the BIOS setup screen. After�a�setting�is�configured,�press��to�save�and�exit;� otherwise,�the�configuration�will�not�be�saved�in�the�BIOS. 1.2 COM 2 Mode Selection (RS232/422/ RS485) 1. Access�the�“NCT6106D�Super�IO�Configuration”�item� from�the�“Advanced”�tab. 2. Select�“Serial�Port�2�Configuration”.�The�COM�2�mode� can�be�configured�via�the�“Serial�Port2�Mode”�item. BIOS Setup Program 3. Select�the�“RS485”�option.�Autoflow�and�termination� resistors can be enabled or disabled. 1.3 H/W Monitor and Smart Fan Mode Configuration 1. Access�the�“H/W�Monitor”�item�from�the�“Advanced”�tab� to check the voltage temperature and fan speed. 1.4 LAN PXE Mode Selection 1. Access�the�“Network�Stack�Configuration”�item�from�the� “Advanced”�tab. BIOS Setup Program (Cont.)

2. Select�the�“Enabled”�option�for�the�“Network�Stack”� item. 1.5 Boot Option Filter 1. Access�the�“CSM�Configuration”�item�from�the����������� “Advanced”�tab.�Users�can�select�“UEFI�only”�or� “Legacy�only”�for�“Boot�Option�Filter”�configuration. 2. Configure�the�Video�and�Storage�item�settings�to�match� the�Boot�Option�Filter�configuration. BIOS Setup Program (Cont.) BIOS Setup Program (Cont.) 1.6 Graphics Configuration 1. Access�the�“System�Agent�(SA)�Configuration”�item� from�the�“Chipset”�tab. 2. Click�on�the�“Graphics�Configuration”�item. 3. Select�the�“LCD�Control”�item.

4. The�Primary�IGFX�Boot�Display�item�can�be�configured� as�“VBIOS�Default”,�“DP”,�“LVDS”,�or�“VGA”. 5. The�Brightness�Mode�Control�item�configuration�is�set� to�“Chipset”�by�default.�This�means�users�can�adjust�the� system brightness via the OS brightness dimmer. 6. Access�the�“Brightness�Manual�Control”�item�to�select� from six brightness level options. BIOS Setup Program (Cont.) BIOS Setup Program (Cont.) 1.7 Wake-On-LAN and Ring 1. In�the�“Chipset”�tab�click�the�“PCH-IO�Configuration”� item�to�access�“PCIE�Wake”�configuration.�Select�the� “Enabled”�option�to�allow�wake-on-LAN�function. 2. In�the�“Chipset”�tab�click�the�“PCH-IO�Configuration”� item�to�access�“Wake�on�Ring”�configuration.�Select�the� “Enabled”�option�to�allow�wake-on-ring�function. 1.8 AT and ATX Settings In�the�“Chipset”�tab�click�the�“PCH-IO�Configuration”�item� to�access�the�“Restore�AC�Power�Loss”�item.�Set�the�item� configuration�to�“Power�On”,�“Power�Off”,�or�“Last�State”.