Datalogic LD46 Instructions

LD CATALOG SECTION LD46 Luminescence sensor 10…20 mm (LD46-UL-715) 20…40 mm (LD46-UL-755) 30…50 mm (LD46-UL-735) Spot dimension 2x8 mm at 10 mm 3x11 mm at 24 mm 4x15 mm at 50 mm Switching frequency 2 kHz Response Time 250 µs Light emission UV-HP LED Setting push buttons Power supply Vdc 15…30 V Vac Vac/dc Output PNP NPN NPN/PNP • relay other 0…5 V Analog output Connection cable connector • pig-tail Approximate dimensions (mm) 31x81x58 Housing material aluminium Mechanical protection IP67 (*) ATEX II 3DG APPLICATIONS • Packaging and labeling machinery • Food, Cosmetic and Pharmaceutical • Ceramic tiles selection and sorting LUMINESCENCE SENSOR LINE IN STANDARD METAL HOUSING LD46 • UV high power LED emission • High sensitivity on fluorescent marks • 10 - 50 mm detection distance • 2 kHz switching frequency • NPN/PNP and 0-5 V analog outputs LUMINESCENCE SENSORS

TECHNICAL DATA DIMENSIONS TECHNICAL DATA 15…30 Vdc limits value 2 Vpp max. d): 50mA max @ 24Vcc 1 PNP output 1 NPN output 100 mA max SETTING KEYLOCK function (patent-covered) The KEYLOCK function deactivates the keyboard thus avoiding accidental changes in the sensor setting. At sensor powering the keyboard is blocked (KEYLOCK LED OFF). To activate it, press for 5 seconds until the KEYLOCK LED (orange) turns ON. The keyboard is automatically blocked if not used for 2 minutes. Unblock the keyboard to proceed with sensor adjustment. DELAY SETTING The DELAY extends the minimum ac allowing even slower interface systems The delay is signalled by the correspond Delay activation - Press for 2 sec until DELAY LED Delay deactivation - Press for 2 sec until DELAY L OFF. OUTPUT OVERLOAD The digital output overload is signalled LED. ANALOGUE OUTPUT The analogue output supplies a voltage the sensor. The voltage supplied is 0.75 DETECTION ON OUT with DELAY OFF 20ms ON OUT without DELAY OFF DIMENSIONS Ø18.8 39.1 60.7 44.7 M20x0.75 M20x0.75 Ø25 M12x1 40 15.5 31.5 Ø18.8 28 M20x0.75 Ø28 24 28 N°2 M5 depth 6mm  3.5mm passing holes 4 8.5 LD46-UL-755 (22mm LENS) 735 NS) LD46-UL-715 (9mm LENS) mm N°4 M5 depth 6mm max. 15.8 31.9 2 27.5 4.8 79 62.9 28 5 21 7.4 Power supply 15 … 30 Vdc (limit values) Ripple 2 Vpp max. Consumption (output current excluded) 50 mA max. at 24 Vdc Light emission UV LED 375 nm Setting SET push-buttons Indicators yellow OUTPUT LED green READY LED orange DELAY LED and KEYLOCK LED 5-segment bargraph Output PNP/NPN; analog output Output current 100 mA max. Saturation voltage 2 V max. Response time 250 µs Switching frequency 2 kHz Connection M12 5-pole connector Dielectric strength 500 Vac, 1 min between electronics and housing Insulating resistance >20 MΩ, 500 Vdc between electronics and housing Electrical protection class 2, double insulation Mechanical protection IP67 Ambient light rejection according to EN 60947-5-2 Vibrations 0,5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) Shock resistance 11 ms (30 G) 6 shock for every axis (EN60068-2-27) Minimum spot dimension 2 x 8 mm at 10 mm (mod. LD46-UL-715) 3x11 mm at 24 mm (mod. LD46-UL-755) 4x15 mm at 50 mm (mod. LD46-UL-735) Housing material aluminium Lens material glass Operating temperature -10 … 55 °C Storage temperature -20 … 70 °C Weight 180 g max.

G F A C D E B A B C D LD46-UL E F G F TL SERIES INSTRUCTION MANUAL CONTROLS OUTPUT LED The red LED indicates the output status. READY LED During functioning, the green LED permanently ON indicates a normal operating condition; fast blinking indicates an output overload condition. See the “SETTING” paragraph for setup procedure indications. MARK / BKGD PUSHBUTTON The pushbutton activates the setup procedure. INSTALLATION Operating distance is rated starting from the lens front face. The M12 connector or cable exit can be rotated in three positions by loosening the locking screw. Tighten the locking screw when finished. The beam direction may be changed swapping the cap and the lens. Detecting marks on a reflective surface is improved adjusting the beam direction to 5° … 20° from surface axis. CONNECTIONS + 10 … 30 Vdc REMOTE A * BROWN RED ORANGE GREY REMOTE B * ANALOG OUTPUT WHITE BLUE NPN/PNP 0 V SHIELD ** * = Connect the unused REMOTE wires to 0 V. ** = The cable shield is insulated from the sensor housing; it is recommended to connect the shield to 0 V. M12 CONNECTOR 10 … 30 Vdc - + NPN/PNP 0 V ANALOG OUTPUT (WHITE) (BROWN) (BLUE) (BLACK) 2 3 1 4 DIMENSIO 7.5 Ø25 READY LED OUTPUT LED BKGD PUSHBUTTON . Ø25 31 n°.4 M n°.4 M 81.2 14.1 27.5 42.2 58 36.6 28 4.3 4.3 CAP 9 mm LENS TL-x6x 18 mm LENS MARK PUSHBUTTON TECHNICAL Power supply: 10 … 30 V Ripple: Current consumption (output current excluded): Output: NPN or PNP, pull Output current: Analog output: 0 … 2 V ± 10% (white 90%) Output saturation voltage: 1V max Response time: 50 Switching frequency: 10 k Timing function: Indicators: OUTP Setting: by pushbutto Retention data: Operating temperature: Storage temperature: Electric shock protection: Operating distance: 9 m Minimum spot dimension: 1.5 x 5 mm (TL Depth of field: ± 3 mm Emission type: green (526 nm) / red (6 Ambient light rejection: Vibration: 0.5 mm amplitude, Shock resistance: 11 ms (30 DARK/LIGHT selection: Housing: Protection class: Connections: 3 m shield Weight: 450 g. max. c CONFIGURATION A double selector and a switch are available removing the sensor side cover. The selector allows to enable the output timing function and choose the pushbuttons and REMOTE inputs 1 2 ON REMOTE SET FORMAT TIMING ON OFF operating mode; the switch allows to select the output type (NPN or PNP). TL SERIES INSTRUCTION MANUAL CONTROLS OUTPUT LED The red LED indicates the output status. READY LED During functioning, the green LED permanently ON indicates a normal operating condition; fast blinking indicates an output overload condition. See the “SETTING” paragraph for setup procedure indications. MARK / BKGD PUSHBUTTON The pushbutton activates the setup procedure. INSTALLATION Operating distance is rated starting from the lens front face. The M12 connector or cable exit can be rotated in three positions by loosening the locking screw. Tighten the locking screw when finished. The beam direction may be changed swapping the cap and the lens. Detecting marks on a reflective surface is improved adjusting the beam direction to 5° … 20° from surface axis. CONNECTIONS + 10 … 30 Vdc REMOTE A * BROWN RED ORANGE GREY REMOTE B * ANALOG OUTPUT WHITE BLUE NPN/PNP 0 V SHIELD ** * = Connect the unused REMOTE wires to 0 V. ** = The cable shield is insulated from the sensor housing; it is recommended to connect the shield to 0 V. M12 CONNECTOR 10 … 30 Vdc - + NPN/PNP 0 V ANALOG OUTPUT (WHITE) (BROWN) (BLUE) (BLACK) 2 3 1 4 DIMENSIONS 7.5 Ø25 READY LED OUTPUT LED BKGD PUSHBUTTON . Ø25 31 n°.4 M5x6 n°.4 M5x0.2 81.2 14.1 27.5 28 42.2 58 36.6 28 4.3 4.3 CAP 9 mm LENS TL-x6x 18 mm LENS MARK PUSHBUTTON TECHNICAL DA Power supply: 10 … 30 Vdc Ripple: Current consumption (output current excluded): Output: NPN or PNP, pull dow Output current: Analog output: 0 … 2 V ± 10% (white 90%); 5.5 Output saturation voltage: 1V max. N Response time: 50 s Switching frequency: 10 kHz Timing function: 2 Indicators: OUTPUT L Setting: by pushbuttons / Retention data: no Operating temperature: Storage temperature: Electric shock protection: Operating distance: 9 mm (T Minimum spot dimension: 1.5 x 5 mm (TL-x1 Depth of field: ± 3 mm (T Emission type: green (526 nm) / red (630 Ambient light rejection: a Vibration: 0.5 mm amplitude, 10 … Shock resistance: 11 ms (30 G) DARK/LIGHT selection: Housing: Protection class: Connections: 3 m shielded c Weight: 450 g. max. cable CONFIGURATION A double selector and a switch are available removing the sensor side cover. The selector allows to enable the output timing function and choose the pushbuttons and REMOTE inputs 1 2 ON REMOTE SET FORMAT TIMING ON OFF operating mode; the switch allows to select the output type (NPN or PNP). 2 4 6 8 10 R % Standard 9 mm lens (2 x 8 mm spot at 10 mm) Standard 22 mm lens (3 x 11 mm spot at 24 mm) Standard 40 mm lens (4 x 15 mm spot at 50 mm) mm mm mm +/- push-buttons SET push-button yellow OUTPUT LED green READY LED orange DELAY LED orange KEYLOCK LED Bargraph M12 CONNECTOR INDICATORS AND SETTINGS CONNECTIONS DETECTION DIAGRAMS

condition and blinking ndition. N indicates the timing output. indicates the active keyboard status. gnalled on the bargraph. button unlocks the keyboard, memorises the al output timing. -buttons edure is activated by pressing the and for setup procedure indications. STALLATION by means the two Ø3.5mm housing’s holes 6 mm max. depth. y long screws can damage the product. at five different positions by rotating the block. ed by a mechanical blocking system. even after sensor installation as the connector d inside the housing. TECHNICAL DATA Power supply: 15…30 Vdc limits value Ripple: 2 Vpp max. Consumption (output current excluded): 50mA max @ 24Vcc Output: 1 PNP output 1 NPN output Output current: 100 mA max. Output saturation voltage:  2 V Analogue output: 0.75 … 5.5 V max. Analogue output impedance: 2.2 k (short-circuit protection) Response time: 250 s Switching frequency: 2 kHz Delay: 0 / 20 ms selectable (no-delay default configuration) Indicators: OUT LED (yellow) / READY LED (green) DELAY LED and KEYLOCK LED (orange) 5-segment bargraph Push-buttons: +, SET, - Operating temperature: -10 … 55 °C Storage temperature: -20 … 70 °C Electric shock protection: double insulation KEYLOCK func The KEYLOCK changes in the s At sensor pow activate it, pres ON. The keyboard is Unblock the key NORMAL FUNC During normal visualises the se SENSITIVITY A This mode regu the capability luminescence de DIMENSIONS Ø18.8 M20x0.75 M20x0.75 Ø25 31.5 Ø18.8 28 Ø33 M20x0.75 Ø28 Ø18.8 N°2 M5 depth 6mm  3.5mm passing holes 4 21.5 25.4 8.5 LD46-UL-755 (22mm LENS) LD46-UL-735 (40mm LENS) LD46-UL-715 (9mm LENS) 4.8 OPTIC FUNCTION EMISSION CONNECTION OUTPUT MODEL ORDER No. Luminescence sensor 10-20 mm Vertical spot M12 Connector NPN/PNP LD46-UL-715 955201000 20-40 mm Vertical spot LD46-UL-755 955201010 30-50 mm Vertical spot LD46-UL-735 955201020 MODEL DESCRIPTION ORDER No. Lens No.9 glass lens with 9 mm focus 95ACC2670 Lens No.22 glass lens with 22 mm focus 95ACC1100 Lens No.40 glass lens with 40 mm focus 95ACC2740 Lens No.50 glass lens with 50 mm focus S73030511 22 mm LENS (LD46-UL-755) 9 mm LENS (LD46-UL-715) 40 mm LENS (LD46-UL-735) 50 mm LENS TYPE DESCRIPTION LENGTH MODEL ORDER No. Axial M12 Connector 5-pole, grey, P.V.C. 3 m CS-A1-03-G-03 95ACC2110 5 m CS-A1-03-G-05 95ACC2120 10 m CS-A1-03-G-10 95ACC2140 5-pole, U.L., black, P.V.C 3 m CS-A1-03-U-03 95ASE1170 5 m CS-A1-03-U-05 95ASE1180 10 m CS-A1-03-U-10 95ASE1190 15 m CS-A1-03-U-15 95ASE1200 25 m CS-A1-03-U-25 95ASE1210 50 m CS-A1-03-U-50 95A252700 MODEL SELECTION AND ORDER INFORMATION ACCESSORIES CABLES The company endeavours to continuously improve and renew its products; for this reason the technical data and contents of this catalogue may undergo variations without prior notice. For correct installation and use, the company can guarantee only the data indicated in the instruction manual supplied with the products. Product and Company names and logos referenced may be either trademarks or registered trademarks of their respective companies. We reserve the right to make modifications and improvements. Rev. 03, 04/2019