Craftsman 486.242112 Owner's Manual

LAWNSWEEPER Model No. 486.242112 Owner's Manual CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. • Safety • Assembly • Operation • Maintenance • Parts PRINTED IN U.S.A. FORM NO. 49535 (REV. 1/05) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman IMPORTANT - READ THIS FIRST!!! For Missing Parts or Assembly Questions Please Call 866-576-8388 Mon.-Fri. 7 am - 5 pm CST. FAX 217-728-2032 or e-mail [email protected] [email protected] Missing parts will be sent UPS in 24 hours directly to your home. ®

For two years from the date of purchase, when this Lawnsweeper is maintained and lubricated according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or workmanship. This warranty does not cover repairs necessary because of operator abuse or negligence, including the failure to maintain the equipment according to instructions contained in the owner's manual; and Lawnsweeper used for commercial or rental purposes. WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES. This warranty applies only while this product is in the United States. This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co. D/817WA, Hoffman Estates, Chicago, IL 60179 Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. 1. Read the vehicle and sweeper owners manuals and know how to operate your vehicle and sweeper before using this sweeper attachment. Always instruct other users before they operate the sweeper. 2. Do not permit children to operate sweeper. 3. Do not permit anyone to ride on sweeper. 4. Never attach the hopper rope to any part of your body or clothing! Never hold onto the rope while towing the sweeper! Attach the rope to the towing vehicle to keep it away from wheels and rotating parts. 5. Operate the sweeper at reduced speed on rough terrain, near ditches and on hillsides to prevent loss of control. 6. Vehicle braking and stability may be affected with the attachment of this sweeper. Do not fi ll sweeper to maximum capacity without checking the capability of the towing vehicle to safely pull and stop with the sweeper attached. Stay off of steep slopes. 7. Stop and inspect vehicle and sweeper for damage after striking an object. Repair any damage before continuing operation. 8. Keep sweeper away from fi re. Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn. 9. Before storing the sweeper, always empty the hopper bag to avoid spontaneous combustion. 10. Follow maintenance and lubrication instructions as outlined in the maintenance section of this manual. Look for this symbol to point out important safety precautions. It means--Attention!! Become alert!! Your safety is involved. Maintenance Schedule ..................................................12 Storage ..........................................................................12 Service and Adjustments ...............................................13 Troubleshooting .............................................................13 Repair Parts Illustration .................................................14 Repair Parts List ............................................................15 Parts Ordering/Service ................................... Back Cover Safety Rules ....................................................................1 Full Size Hardware Chart ................................................3 Carton Contents ..............................................................4 Sweeper Assembly Instructions ......................................5 Hopper Assembly Instructions .........................................7 Operation .......................................................................11 MODEL NUMBER: 486.242112 SERIAL NUMBER: __________________ DATE OF PURCHASE: __________________ SAFETY WARRANTY TABLE OF CONTENTS The model and serial numbers will be found on a decal attached to the lawnsweeper. You should record both the serial number and the date of purchase and keep in a safe place for future reference.

K 1 Hairpin Cotter, 1/8" L 6 Hairpin Cotter, 3/32" M 2 Clevis Pin, 3/8" x 1/2" N 2 Clevis Pin, 1/4" x 1-1/8" O 2 Clevis Pin, 1/4" x 1-3/4" P 2 Vinyl Cap Q 4 Plastic Plug R 1 Grip S 1 Knob, Plastic A 2 Hex Bolt, 5/16-18 x 3" Lg. B 2 Hex Bolt, 5/16-18 x 2-1/2" Lg. B 2 Hex Bolt, 5/16-18 x 2-1/2" Lg. C 4 Hex Bolt, 5/16-18 x 1-3/4" Lg. C 4 Hex Bolt, 5/16-18 x 1-3/4" Lg. D 1 Carriage Bolt, 5/16-18 x 1" Lg. D 1 Carriage Bolt, 5/16-18 x 1" Lg. E 8 Nylock Nut, 5/16" E 8 Nylock Nut, 5/16" F 2 Palnut, 3/8" F 2 Palnut, 3/8" G 1 Flat Washer, 5/16" Standard G 1 Flat Washer, 5/16" Standard H 1 Washer, Tooth Lock 5/16" H 1 Washer, Tooth Lock 5/16" I 1 Spacer Bushing, I 1 Spacer Bushing, REF. QTY. DESCRIPTION A 2 Hex Bolt, 5/16-18 x 3" Lg. B 2 Hex Bolt, 5/16-18 x 2-1/2" Lg. C 4 Hex Bolt, 5/16-18 x 1-3/4" Lg. D 1 Carriage Bolt, 5/16-18 x 1" Lg. E 8 Nylock Nut, 5/16" F 2 Palnut, 3/8" G 1 Flat Washer, 5/16" Standard H 1 Washer, Tooth Lock 5/16" I 1 Spacer Bushing, REF. QTY. DESCRIPTION J 2 Hitch Spacer, 3/4" K 1 Hairpin Cotter, 1/8" L 6 Hairpin Cotter, 3/32" M 2 Clevis Pin, 3/8" x 1/2" N 2 Clevis Pin, 1/4" x 1-1/8" O 2 Clevis Pin, 1/4" x 1-3/4" P 2 Vinyl Cap Q 4 Plastic Plug R 1 Grip S 1 Knob, Plastic REF. QTY. DESCRIPTION J 2 Hitch Spacer, 3/4" K 1 Hairpin Cotter, 1/8" L 6 Hairpin Cotter, 3/32" M 2 Clevis Pin, 3/8" x 1/2" N 2 Clevis Pin, 1/4" x 1-1/8" O 2 Clevis Pin, 1/4" x 1-3/4" P 2 Vinyl Cap Q 4 Plastic Plug R 1 Grip S 1 Knob, Plastic REF. QTY. DESCRIPTION A 2 Hex Bolt, 5/16-18 x 3" Lg. B 2 Hex Bolt, 5/16-18 x 2-1/2" Lg. C 4 Hex Bolt, 5/16-18 x 1-3/4" Lg. D 1 Carriage Bolt, 5/16-18 x 1" Lg. E 8 Nylock Nut, 5/16" F 2 Palnut, 3/8" G 1 Flat Washer, 5/16" Standard H 1 Washer, Tooth Lock 5/16" I 1 Spacer Bushing, HARDWARE PACKAGE CONTENTS A B C D E L K G P R S H O I J SHOWN FULL SIZE NOT SHOWN FULL SIZE N M Q F

9. Rope 10. Hopper Bag 11. Rear Hopper Tube (2) 12. Upper Hopper Tube (2) 13. Lower Hopper Tube (2) 14. Hopper Bag Pivot Rod 15. Hopper Support Rod (2) 16. Bag Frame Strap 1. Sweeper Housing Assembly 2. Bag Arm Tube (2) 3. Hitch Tube, L.H. (Left Hand) 4. Hitch Bracket Assembly 5. Hitch Bracket, Bent 6. Height Adjustment Strap 7. Height Adjustment Handle 8. Hitch Tube, R.H. (Right Hand) CARTON CONTENTS TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (1) Screwdriver (1) Hammer (1) Adjustable Wrench (1) 1/2" Open End or Box End Wrench (1) 3/8" Open End or Box End Wrench ASSEMBLY STEP 1 - REMOVE PARTS FROM CARTON • To protect painted parts, lay them on cardboard or a mat. • Remove the sweeper housing, the loose parts and the hardware package from the carton. Lay out the parts and hardware as shown on pages 3 and 4. 1 2 3 5 6 7 8 2 9 10 11 12 14 15 16 4 11 13 12 13

• Place the spacer bushing (I) into the hole in the height adjustment strap. Place the strap and bushing between the hitch tubes, aligning them with the rear hole. Fasten the hitch tubes together, with the strap and bushing between them, using two hex bolts (A) and nylock nuts (E). Do not tighten yet. See fi gure 2. FIGURE 1 FIGURE 2 FIGURE 3 STEP 5 - MEASURE TRACTOR HITCH • Use the mark beside this paragraph to measure the height of the tractor hitch. The mark is 10" from the bottom of the page. If the tractor hitch is less than 10" above the ground, go to STEP 6a. If the tractor hitch is 10" or more above the ground, go to STEP 6b. STEP 6a - ASSEMBLE HITCH BRACKETS • If the tractor hitch is less than 10" above the ground, place the bent hitch bracket underneath the hitch tubes and place the hitch bracket assembly on top of the hitch tubes. Insert two hex bolts (B) through the brackets, with the rear hex bolt between the cross bolts in the hitch tubes. Secure the hex bolts (B) with two nylock nuts (E). See fi gure 3. Do not tighten yet. • Assemble the two spacers (J) onto the hitch pin and secure the pin with the hairpin cotter (K). See fi gure 3. FIGURE 4 HEX BOLT (A) NYLOCK NUT (E) SPACER BUSHING (I) HEIGHT ADJUSTMENT STRAP NYLOCK NUTS (E) HITCH BRACKET ASSEMBLY BENT HITCH BRACKET HEX BOLTS (B) HAIRPIN COTTER (K) SPACERS (J) STEP 6b - ASSEMBLE HITCH BRACKETS • If the tractor hitch is 10" or more above the ground, place the bent hitch bracket on top of the hitch tubes and place the hitch bracket assembly underneath the hitch tubes. Insert two hex bolts (B) through the brackets, with the rear hex bolt between the cross bolts in the hitch tubes. Secure the hex bolts (B) with two nylock nuts (E). See fi gure 4. Do not tighten yet. • Assemble the two spacers (J) onto the hitch pin and secure the pin with the hairpin cotter (K). See fi gure 4. NYLOCK NUTS (E) BENT HITCH BRACKET HITCH BRACKET ASSEMBLY HEX BOLTS (B) SPACERS (J) HAIRPIN COTTER (K) 10" HEX BOLT (C) HITCH TUBE (L.H.) PLASTIC TIE NYLOCK NUT (E) TUBE MARKED “77L” HOUSING MARKED “L” STEP 2 - ASSEMBLE HITCH TUBES • The hitch tubes are stamped with a "77L" for the left tube and a "76R" for the right tube. The sweeper housing is marked with and "L" on the left with side and an "R" on the right side. See fi gure 1. • Hold the left hitch tube against the left side of the sweeper so that the "77L" on the tube faces away from the sweeper. Attach the hitch tube using two hex bolts (C) and nylock nuts (E). Repeat for the right hitch tube, but with the "76R" facing in toward the right side of the sweeper. Do not tighten yet. See fi gure 1. STEP 3 - REMOVE PLASTIC TIE • Remove the plastic tie that fastens the height adjustment tube to the front of the sweeper housing. See fi gure 1.

• Place the tooth-lock washer (H) between the height adjustment handle and the height adjustment strap. Insert the carriage bolt (D) through the handle, the tooth-lock washer and the strap. Assemble the fl at washer (G) and the plastic knob (S) onto the end of the bolt and tighten. See fi gure 6. STEP 7 - TIGHTEN BOLTS • At this time tighten the four bolts in fi gure 1 that fasten the hitch tubes to the sweeper housing. Next, tighten the two bolts in fi gure 2 that fasten the ends of the hitch tubes together. Finally, tighten the two bolts in fi gure 3 or 4 that fasten the hitch brackets to the hitch tubes. STEP 8 - ATTACH HANDLE • Assemble the height adjustment handle to the height adjustment tube on the front of the sweeper housing. Use the curved head bolts, bowed washers, lock washers and hex nuts which come pre-assembled to the tube. Position the height adjustment handle side to side so that the height adjustment strap will align up against the outside of the handle and then tighten the nuts. See fi gure 5. • Assemble the grip (R) onto the end of the height adjustment handle as shown in fi gure 5. CURVED HEAD BOLT BOWED WASHER LOCK WASHER HEX NUT GRIP (R) HEIGHT ADJUSTMENT HANDLE HEIGHT ADJUSTMENT TUBE HEIGHT ADJUSTMENT STRAP CARRIAGE BOLT (D) TOOTH LOCK WASHER (H) KNOB (S) FLAT WASHER (G) HEIGHT ADJUSTMENT HANDLE HEIGHT ADJUSTMENT STRAP

STEP 10 - ASSEMBLE UPPER TUBES • Fit the ends of the two upper hopper tubes into the ends of a rear hopper tube. Align the holes in the ends of the tubes and insert plastic plugs (Q). See fi gure 7. NOTE: Either side of the tubes can face up. FIGURE 7 FIGURE 9 UPPER HOPPER TUBE HOPPER BAG BOTTOM STITCHED SLEEVE STEP 11 - ASSEMBLE LOWER TUBES • Fit the ends of the two lower hopper tubes into the ends of a rear hopper tube. Align the holes in the ends of the tubes and insert plastic plugs (Q). See fi gure 8. NOTE: Either side of the rear hopper tube can face up. FIGURE 8 FIGURE 10 LOWER HOPPER TUBE HOPPER BAG BOTTOM UPPER HOPPER TUBE CLEVIS PIN (M) HAIR COTTER PIN (L) UPPER HOPPER TUBE PLASTIC PLUG (Q) REAR HOPPER TUBE LOWER HOPPER TUBE PLASTIC PLUG (Q) REAR HOPPER TUBE STEP 12 - ASSEMBLE TUBES TO BAG • Unfold the hopper bag, reverse the fold of the mesh wind screen and then lay the bag out fl at with the wind screen on top and the Craftsman logo facing down. • Insert the ends of the assembled upper hopper tubes down through the stitched sleeves in the sides of the hopper bag and then slide the tubes back underneath the wind screen. See fi gure 9. • Place the assembled lower hopper tubes into the bottom of the hopper bag and then slide the tubes to the back of the bag. See fi gure 10. • Attach the ends of the lower hopper tubes to the inside of the upper hopper tubes using two clevis pins (M) inserted from the inside, and two hair cotter pins (L). See fi gure 10.

IMPORTANT: Do not over bend the support rods during the following step. Over bending will decrease the supporting tension of the rods. • Assemble the two hopper support rods as shown in fi gure 14. Place the ends of the rods into the holes in the upper and lower hopper tubes, fl exing the rod just enough to fi t into the holes in the tubes. NOTE: The hopper's mesh wind screen is not shown in fi gure 14 in order to better show the hopper support rods. • Fold the bag fl aps around the lower hopper tubes and attach to the bag bottom using the snaps. See fi gure 13. FIGURE 13 STEP 13 - ATTACH BAG BOTTOM • Insert the bag frame strap into the stitched sleeve at the front edge of the bag bottom. See fi gure 11. FIGURE 12 FIGURE 14 CLEVIS PIN (N) HAIR COTTER PIN (L) BAG FRAME STRAP SNAP FLAP SUPPORT RODS BAG FRAME STRAP STITCHED SLEEVE • Assemble the bag frame strap to the holes in the lower hopper tubes using two clevis pins (N) and hair cotter pins (L). See fi gure 12. FIGURE 11

• Slide the hopper bag pivot rod through the upper hole in the upper hopper tubes and through the stitched sleeve at the front edge of the mesh wind screen, assembling a bag arm tube on each side as shown in fi gure 15. STEP 17 - ATTACH HOPPER BAG • To attach the hopper bag to the sweeper, slide the ends of the bag arm tubes into the ends of the hitch tubes and secure with two clevis pins (O) and hairpin cotters (L). See fi gure 18. STEP 16 - ATTACH ROPE • Secure the rope to the center of the upper rear hopper tube as shown in fi gure 17. FIGURE 18 • Assemble a vinyl cap (P) onto each bag arm tube as shown in fi gure 17. • Assemble two palnuts (F) by lightly tapping them onto the ends of the pivot rod with a hammer. See fi gure 16. HINT: To ease assembly of the palnuts, place the bag on its side on a solid surface. With the bottom end of the pivot rod against the surface, tap a palnut onto the top end of the rod. Repeat for other end of rod. FIGURE 15 FIGURE 17 BAG ARM TUBE BAG ARM TUBE HOPPER BAG PIVOT ROD MOUNTING CLAMP MOUNTING CLAMP WIND SCREEN WIND SCREEN UPPER HOLE CLEVIS PIN (O) HAIRPIN COTTER (L) HITCH TUBE HITCH TUBE BAG ARM TUBE MOUNTING CLAMP MOUNTING CLAMP PALNUT (F) CAP (P)

BLACK LINE IS TRACTOR HITCH HITCH BRACKET MOUNTED BELOW HITCH TUBES BLACK LINE IS TRACTOR HITCH HITCH BRACKET MOUNTED ABOVE HITCH TUBES FIGURE 19 • Place the tractor and sweeper on a fl at level surface. • Set the sweeper height adjustment handle to about the middle of its adjustment range. • Attach the sweeper hitch to the tractor hitch, arranging the 3/4" spacers in one of six possible combinations as shown in GROUP A and GROUP B diagrams below. IMPORTANT: To obtain the best performance from your sweeper, arrange the spacers so that the sweeper bag is approximately level with the ground and approximately 5" to 7" off the ground as shown in fi gure 19. GROUP "B" - For vehicles with hitches having 10" to 13" ground clearance. GROUP "A" - For vehicles with hitches having 8" to 10" ground clearance. APPROXIMATELY LEVEL (5" to 7" FROM SURFACE) BRUSH HEIGHT ADJUSTED APPROXIMATELY MID-WAY

CAUTION: Keep sweeper away from fi re. Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn. CAUTION: Never attach the hopper rope to any part of your body or clothing! Never hold onto the rope while towing the sweeper! Attach the rope to the towing vehicle to keep it away from wheels and rotating parts. DUMPING OF SWEEPER • Your sweeper can be dumped easily without getting off of the rider or tractor. Simply pull the rope forward to dump the hopper. Always empty hopper after each use. BRUSH HEIGHT ADJUSTMENT • To adjust your sweeper brushes to the best operating height, loosen the adjustment knob and push down on the height adjustment lever to raise the brush, or push up on the lever to lower the brush. See fi gure 19. Best adjustment is when the brush setting is 1/2" down into the grass. Always mow the grass to an even height before sweeping. SWEEPING SPEED • Try a starting speed of approximately 3 m.p.h. (third gear on most tractors). Depending on the conditions, it may be necessary to adjust the sweeping speed in order to achieve best results. OPERATION Hopper Bag Collects grass clippings, leaves and debris. Hopper Rope Permits dumping of hopper bag from driver's seat. Windscreen Helps prevent collected material from being blown out of hopper bag. Bag Arm Tubes Connects the hopper bag to the sweeper housing. Pivot Rod Allows hopper bag to tilt forward to dump material. Height Adjustment Handle Adjusts the operating height of the sweeper. Height Adjustment Strap Holds the height adjustment handle in position when locked. Knob Locks the height adjustment handle to the height adjustment strap. Hitch Bracket Connects the sweeper to the towing vehicle. Adjusts for various height tractor hitches. HOW TO USE YOUR SWEEPER HOPPER BAG WINDSCREEN BAG ARM TUBE PIVOT ROD HEIGHT ADJUSTMENT HANDLE KNOB HITCH BRACKETS HOPPER ROPE HEIGHT ADJUSTMENT STRAP HEIGHT ADJUSTMENT STRAP

complete regular service. complete regular service. Check for loose fasteners X Check for loose fasteners X Check for worn or damaged parts X X Check for worn or damaged parts X X Lubricate brush shaft bearings X Lubricate brush shaft bearings X Lubricate wheel bearings X Lubricate wheel bearings X Clean Sweeper X X Clean Sweeper X X Clean/Lubricate chain and sprockets X Clean/Lubricate chain and sprockets X Check for loose fasteners X Check for worn or damaged parts X X Lubricate brush shaft bearings X Lubricate wheel bearings X Clean Sweeper X X Clean/Lubricate chain and sprockets X Check for worn or damaged parts X X Lubricate brush shaft bearings X Lubricate wheel bearings X Clean Sweeper X X Clean/Lubricate chain and sprockets X Check for worn or damaged parts X X Lubricate brush shaft bearings X Lubricate wheel bearings X Clean Sweeper X X Clean/Lubricate chain and sprockets X Check for worn or damaged parts X X Lubricate brush shaft bearings X Lubricate wheel bearings X Clean Sweeper X X Clean/Lubricate chain and sprockets X Lubricate wheel bearings X Clean Sweeper X X Clean/Lubricate chain and sprockets X Clean/Lubricate chain and sprockets X COVER FLAT WASHER HEX LOCK NUT HUB CAP CLEAN AND GREASE FIGURE 21 • Every two years, remove the wheels and clean the sprockets, chains and gears found inside the wheel housing. After cleaning, lubricate with an even coat of light grease. To remove the wheel, pop off the hub cap using a screwdriver and remove the lock nut and fl at washer. See fi gure 21. CLEANING • Clean sweeper housing with a soft brush or cloth. • Clean debris from hopper bag with a brush or broom. • Remove any material which has wrapped around brushes or ends of brush shaft. CUSTOMER RESPONSIBILITIES • Read and follow the maintenance schedule and the procedures listed in the maintenance section. Before each use Before each use After each use Twice a year Twice a year Every season Every season Before storage Before storage Every two years Every two years Every two years Clean/Lubricate chain and sprockets X Service Dates SCHEDULED MAINTENANCE • Clean the sweeper after each use. • Inspect for worn or damaged parts, such as brushes and wheels. • Lubricate the brush shaft bearing twice a year with a few drops of light weight oil. See fi gure 20. HEIGHT ADJUSTMENT SLOT HEX BOLT OIL BEARINGS HERE FLAT WASHER FIGURE 20 Clean/Lubricate chain and sprockets X Clean/Lubricate chain and sprockets X Clean/Lubricate chain and sprockets X Clean/Lubricate chain and sprockets X • Clean the sweeper and hopper bag thoroughly to help prevent rust and mildew. • To collapse the hopper bag for storage, remove the two hopper support rods from the rear of the hopper. • Store in a dry area. CAUTION: Before storing the sweeper, always empty the hopper bag to avoid spontaneous combustion. STORAGE

IMPORTANT: Do not remove both wheels at the same time to avoid mixing of parts. (The R.H. and L.H. ratchet sprockets are not interchangeable.) Make notes on the position of washers and snap rings during disassembly. • Remove the dust cover by removing the two rivets which fasten it to the wheel housing. (It is not necessary to remove the dust cover if you are only cleaning and lubricating the chain and sprockets.) • Remove the retaining rings and washers which hold the sprockets onto the shafts. • Remove the chain and both sprockets, holding them in position and sliding them off both of the shafts. (Look for the drive pin, which may fall out of the brush shaft when the ratchet sprocket is removed.) See fi gure 23. • To reassemble, insert the drive pin through the hole at the end of the brush shaft. Make sure the pin slides back and forth easily in the shaft. • Lightly grease both shafts and the chain, and fi ll the ratchet sprocket with grease. Assemble the chain with both sprockets back onto the shafts. • Lightly grease the axle and then reassemble the wheel. The brushes should rotate only during forward rotation of the wheel. If the brushes are driven (rotated) by both forward and reverse rotation of the wheel, the drive pin is jamming in the ratchet gear. Disassemble and clean and lubricate the drive pin and ratchet gear. BRUSH REPLACEMENT NOTE: Brush replacement should be done one brush at a time. • Remove the hopper bag from the sweeper. • Loosen the hex bolts and lock nuts on two single brush retainers which clamp one brush to the double brush retainers. Do Not loosen or remove the bolts which fasten the double brush retainers to the brush shaft. See fi gure 22. • Slide the brush out of the retainers, noting on which side of the brush the bristles overlap. See fi gure 22. • Install new brush, making sure the bristles overlap on the same side of the brush as before. See fi gure 22. GEAR SPROCKET CHAIN RATCHET SPROCKET DRIVE PIN DUST COVER FIGURE 23 BRUSH ROTATION BRUSH ROTATION OVERLAP BRISTLES OVERLAP BRISTLES SINGLE BRUSH RETAINERS DOUBLE BRUSH RETAINER BRUSH SHAFT FIGURE 22 • Brushes set too low. • Brushes are jammed • Wheels are jammed. Wheels skid when sweeping. • Adjust height till brushes are 1/2" down into grass. • Stop sweeper. Remove obstruction. • Remove one wheel at a time to check for obstruction or damage. Refer to Service and Adjustments section. SERVICE AND ADJUSTMENTS TROUBLESHOOTING

PARTS A C AA C D D B B 70 42 43 48 44 75 45 75 73 54 46 74 53 70 44 15 14 16 39 17 18 19 47 56 55 56 20 41 28 30 31 55 25 26 36 38 23 26 25 26 24 29 40 14 81 34 79 22 37 21 37 20 64 76 75 28 2 11 12 13 59 33 81 7 5 4 52 61 63 66 60 49 58 59 68 51 50 69 57 67 65 62 59 1 9 27 8 9 10 32 72 6 3 80 78 77 53 74 71 42 71 43

43 47477 2 Tube, Rear Hopper Frame 43 47477 2 Tube, Rear Hopper Frame 43 47477 2 Tube, Rear Hopper Frame 44 48726 2 Tube, Lower Hopper Frame 44 48726 2 Tube, Lower Hopper Frame 44 48726 2 Tube, Lower Hopper Frame 44 48726 2 Tube, Lower Hopper Frame 45 24189 1 Strap, Bag Frame 45 24189 1 Strap, Bag Frame 45 24189 1 Strap, Bag Frame 45 24189 1 Strap, Bag Frame 46 43938 2 Rod, Hopper Support 34" 46 43938 2 Rod, Hopper Support 34" 46 43938 2 Rod, Hopper Support 34" 46 43938 2 Rod, Hopper Support 34" 47 43737 1 Hopper Rope 47 43737 1 Hopper Rope 47 43737 1 Hopper Rope 47 43737 1 Hopper Rope 48 48401 1 Hopper Bag 48 48401 1 Hopper Bag 48 48401 1 Hopper Bag 48 48401 1 Hopper Bag 49 24191 1 Strap, Height Adjustment 49 24191 1 Strap, Height Adjustment 49 24191 1 Strap, Height Adjustment 49 24191 1 Strap, Height Adjustment 50 23687 1 Bracket, Hitch 50 23687 1 Bracket, Hitch 50 23687 1 Bracket, Hitch 50 23687 1 Bracket, Hitch 51 24192 1 Bracket, Hitch (Straight) 51 24192 1 Bracket, Hitch (Straight) 51 24192 1 Bracket, Hitch (Straight) 51 24192 1 Bracket, Hitch (Straight) 52 24193 1 Handle, Height Adjustment 52 24193 1 Handle, Height Adjustment 52 24193 1 Handle, Height Adjustment 52 24193 1 Handle, Height Adjustment 53 46781 2 Tube, Bag Arm 53 46781 2 Tube, Bag Arm 53 46781 2 Tube, Bag Arm 53 46781 2 Tube, Bag Arm 54 46823 1 Rod, Hopper Bag Pivot 54 46823 1 Rod, Hopper Bag Pivot 54 46823 1 Rod, Hopper Bag Pivot 54 46823 1 Rod, Hopper Bag Pivot 55 44985 2 Wheel & Tire Ass'y. (with bearings) 55 44985 2 Wheel & Tire Ass'y. (with bearings) 55 44985 2 Wheel & Tire Ass'y. (with bearings) 55 44985 2 Wheel & Tire Ass'y. (with bearings) 56 45088 4 Wheel Bearing 56 45088 4 Wheel Bearing 56 45088 4 Wheel Bearing 56 45088 4 Wheel Bearing 57 46782 2 Bolt, Hex 5/16-18 x 3" Lg. 57 46782 2 Bolt, Hex 5/16-18 x 3" Lg. 57 46782 2 Bolt, Hex 5/16-18 x 3" Lg. 57 46782 2 Bolt, Hex 5/16-18 x 3" Lg. 58 43224 2 Bolt, Hex 5/16-18 x 2-1/4" Lg. 58 43224 2 Bolt, Hex 5/16-18 x 2-1/4" Lg. 58 43224 2 Bolt, Hex 5/16-18 x 2-1/4" Lg. 58 43224 2 Bolt, Hex 5/16-18 x 2-1/4" Lg. 59 47810 8 Nut, Nylock 5/16-18 Thread 59 47810 8 Nut, Nylock 5/16-18 Thread 59 47810 8 Nut, Nylock 5/16-18 Thread 59 47810 8 Nut, Nylock 5/16-18 Thread 60 46847 1 Bushing, Spacer 60 46847 1 Bushing, Spacer 60 46847 1 Bushing, Spacer 60 46847 1 Bushing, Spacer 61 43720 1 Knob, Wing 5/16-18 Thread 61 43720 1 Knob, Wing 5/16-18 Thread 61 43720 1 Knob, Wing 5/16-18 Thread 61 43720 1 Knob, Wing 5/16-18 Thread 62 44326 1 Bolt, Carriage 5/16-18 x 1" Lg. 62 44326 1 Bolt, Carriage 5/16-18 x 1" Lg. 62 44326 1 Bolt, Carriage 5/16-18 x 1" Lg. 62 44326 1 Bolt, Carriage 5/16-18 x 1" Lg. 62 44326 1 Bolt, Carriage 5/16-18 x 1" Lg. 63 43081 1 Washer, Flat 5/16" Std. Wrt. 63 43081 1 Washer, Flat 5/16" Std. Wrt. 63 43081 1 Washer, Flat 5/16" Std. Wrt. 63 43081 1 Washer, Flat 5/16" Std. Wrt. 63 43081 1 Washer, Flat 5/16" Std. Wrt. 64 43084 4 Bolt, Hex 5/16-18 x 1-3/4" Lg. 64 43084 4 Bolt, Hex 5/16-18 x 1-3/4" Lg. 64 43084 4 Bolt, Hex 5/16-18 x 1-3/4" Lg. 64 43084 4 Bolt, Hex 5/16-18 x 1-3/4" Lg. 64 43084 4 Bolt, Hex 5/16-18 x 1-3/4" Lg. 65 43943 1 Grip, Height Adjust 65 43943 1 Grip, Height Adjust 65 43943 1 Grip, Height Adjust 65 43943 1 Grip, Height Adjust 65 43943 1 Grip, Height Adjust 66 44732 1 Washer, Tooth Lock 5/16" 66 44732 1 Washer, Tooth Lock 5/16" 66 44732 1 Washer, Tooth Lock 5/16" 66 44732 1 Washer, Tooth Lock 5/16" 66 44732 1 Washer, Tooth Lock 5/16" 67 49493 1 Pin, Hitch 67 49493 1 Pin, Hitch 67 49493 1 Pin, Hitch 67 49493 1 Pin, Hitch 67 49493 1 Pin, Hitch 68 23368 2 Tube, Hitch Spacer 68 23368 2 Tube, Hitch Spacer 68 23368 2 Tube, Hitch Spacer 68 23368 2 Tube, Hitch Spacer 68 23368 2 Tube, Hitch Spacer 69 43343 1 Hairpin Cotter, 1/8" 69 43343 1 Hairpin Cotter, 1/8" 69 43343 1 Hairpin Cotter, 1/8" 69 43343 1 Hairpin Cotter, 1/8" 69 43343 1 Hairpin Cotter, 1/8" 70 44917 2 Palnut, 3/8" 70 44917 2 Palnut, 3/8" 70 44917 2 Palnut, 3/8" 70 44917 2 Palnut, 3/8" 70 44917 2 Palnut, 3/8" 71 48402 4 Plug, 1/4" 71 48402 4 Plug, 1/4" 71 48402 4 Plug, 1/4" 71 48402 4 Plug, 1/4" 71 48402 4 Plug, 1/4" 72 48365 2 Pin, Clevis 1/4" x 1-1/8" 72 48365 2 Pin, Clevis 1/4" x 1-1/8" 72 48365 2 Pin, Clevis 1/4" x 1-1/8" 72 48365 2 Pin, Clevis 1/4" x 1-1/8" 72 48365 2 Pin, Clevis 1/4" x 1-1/8" 73 48366 2 Pin, Clevis 3/8" x 1/2" 73 48366 2 Pin, Clevis 3/8" x 1/2" 73 48366 2 Pin, Clevis 3/8" x 1/2" 73 48366 2 Pin, Clevis 3/8" x 1/2" 73 48366 2 Pin, Clevis 3/8" x 1/2" 74 44481 2 Cap, Vinyl 74 44481 2 Cap, Vinyl 74 44481 2 Cap, Vinyl 74 44481 2 Cap, Vinyl 74 44481 2 Cap, Vinyl 75 43055 6 Hairpin Cotter, 3/32" #3 75 43055 6 Hairpin Cotter, 3/32" #3 75 43055 6 Hairpin Cotter, 3/32" #3 75 43055 6 Hairpin Cotter, 3/32" #3 75 43055 6 Hairpin Cotter, 3/32" #3 76 46867 2 Pin, Clevis 1/4" x 1-1/2" Lg. 76 46867 2 Pin, Clevis 1/4" x 1-1/2" Lg. 76 46867 2 Pin, Clevis 1/4" x 1-1/2" Lg. 76 46867 2 Pin, Clevis 1/4" x 1-1/2" Lg. 76 46867 2 Pin, Clevis 1/4" x 1-1/2" Lg. 77 44230 1 Spring, Hitch Pin 77 44230 1 Spring, Hitch Pin 77 44230 1 Spring, Hitch Pin 77 44230 1 Spring, Hitch Pin 77 44230 1 Spring, Hitch Pin 78 142 1 Pin, Cotter 1/8" x 3/4" Lg. 78 142 1 Pin, Cotter 1/8" x 3/4" Lg. 78 142 1 Pin, Cotter 1/8" x 3/4" Lg. 78 142 1 Pin, Cotter 1/8" x 3/4" Lg. 78 142 1 Pin, Cotter 1/8" x 3/4" Lg. 79 49102 4 Screw, #12 x 1/2" Hex Head 79 49102 4 Screw, #12 x 1/2" Hex Head 79 49102 4 Screw, #12 x 1/2" Hex Head 79 49102 4 Screw, #12 x 1/2" Hex Head 79 49102 4 Screw, #12 x 1/2" Hex Head 80 43070 1 Washer, 3/8" Flat 80 43070 1 Washer, 3/8" Flat 80 43070 1 Washer, 3/8" Flat 80 43070 1 Washer, 3/8" Flat 80 43070 1 Washer, 3/8" Flat 81 C-9M5732 14 Rivet, Pop 81 C-9M5732 14 Rivet, Pop 81 C-9M5732 14 Rivet, Pop 81 C-9M5732 14 Rivet, Pop 81 C-9M5732 14 Rivet, Pop 49535 1 Owners Manual 49535 1 Owners Manual 49535 1 Owners Manual 49535 1 Owners Manual 49535 1 Owners Manual REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. NO. NO. NO. 1 46776 1 Hitch Tube, R.H. 1 46776 1 Hitch Tube, R.H. 1 46776 1 Hitch Tube, R.H. 1 46776 1 Hitch Tube, R.H. 1 46776 1 Hitch Tube, R.H. 2 46777 1 Hitch Tube, L.H. 2 46777 1 Hitch Tube, L.H. 2 46777 1 Hitch Tube, L.H. 2 46777 1 Hitch Tube, L.H. 2 46777 1 Hitch Tube, L.H. 3 63467 1 Housing Assembly 3 63467 1 Housing Assembly 3 63467 1 Housing Assembly 3 63467 1 Housing Assembly 3 63467 1 Housing Assembly 4 46778 1 Skirt, 42" 4 46778 1 Skirt, 42" 4 46778 1 Skirt, 42" 4 46778 1 Skirt, 42" 4 46778 1 Skirt, 42" 5 24186 1 Retainer, Skirt 5 24186 1 Retainer, Skirt 5 24186 1 Retainer, Skirt 5 24186 1 Retainer, Skirt 5 24186 1 Retainer, Skirt 6 63468 1 Height Adjustment Tube Ass'y. 6 63468 1 Height Adjustment Tube Ass'y. 6 63468 1 Height Adjustment Tube Ass'y. 6 63468 1 Height Adjustment Tube Ass'y. 6 63468 1 Height Adjustment Tube Ass'y. 7 44947 2 Bolt, Cvd. Hd. 5/16-18 x 1-5/8" Lg. 7 44947 2 Bolt, Cvd. Hd. 5/16-18 x 1-5/8" Lg. 7 44947 2 Bolt, Cvd. Hd. 5/16-18 x 1-5/8" Lg. 7 44947 2 Bolt, Cvd. Hd. 5/16-18 x 1-5/8" Lg. 7 44947 2 Bolt, Cvd. Hd. 5/16-18 x 1-5/8" Lg. 8 44695 2 Washer, Bowed 1" x .32" x .06" 8 44695 2 Washer, Bowed 1" x .32" x .06" 8 44695 2 Washer, Bowed 1" x .32" x .06" 8 44695 2 Washer, Bowed 1" x .32" x .06" 8 44695 2 Washer, Bowed 1" x .32" x .06" 9 43086 6 Lock Washer, 5/16" 9 43086 6 Lock Washer, 5/16" 9 43086 6 Lock Washer, 5/16" 9 43086 6 Lock Washer, 5/16" 9 43086 6 Lock Washer, 5/16" 10 43083 2 Nut, Hex 5/16-18 Thread 10 43083 2 Nut, Hex 5/16-18 Thread 10 43083 2 Nut, Hex 5/16-18 Thread 10 43083 2 Nut, Hex 5/16-18 Thread 10 43083 2 Nut, Hex 5/16-18 Thread 11 62489 2 Brush Bushing Ass'y. 11 62489 2 Brush Bushing Ass'y. 11 62489 2 Brush Bushing Ass'y. 11 62489 2 Brush Bushing Ass'y. 11 62489 2 Brush Bushing Ass'y. 12 44232 2 Ball Bearing 12 44232 2 Ball Bearing 12 44232 2 Ball Bearing 12 44232 2 Ball Bearing 12 44232 2 Ball Bearing 13 1629-56 2 Retainer, Dust Cover 13 1629-56 2 Retainer, Dust Cover 13 1629-56 2 Retainer, Dust Cover 13 1629-56 2 Retainer, Dust Cover 13 1629-56 2 Retainer, Dust Cover 14 24198 1 Brush Shaft 14 24198 1 Brush Shaft 14 24198 1 Brush Shaft 14 24198 1 Brush Shaft 14 24198 1 Brush Shaft 15 46780 4 Brush, 42" 15 46780 4 Brush, 42" 15 46780 4 Brush, 42" 15 46780 4 Brush, 42" 15 46780 4 Brush, 42" 16 43012 8 Bolt, Hex 1/4-20 x 3/4" Lg. 16 43012 8 Bolt, Hex 1/4-20 x 3/4" Lg. 16 43012 8 Bolt, Hex 1/4-20 x 3/4" Lg. 16 43012 8 Bolt, Hex 1/4-20 x 3/4" Lg. 16 43012 8 Bolt, Hex 1/4-20 x 3/4" Lg. 17 47189 12 Nut, Nylock 1/4-20 Thread 17 47189 12 Nut, Nylock 1/4-20 Thread 17 47189 12 Nut, Nylock 1/4-20 Thread 17 47189 12 Nut, Nylock 1/4-20 Thread 17 47189 12 Nut, Nylock 1/4-20 Thread 18 23580 4 Retainer, Brush (Double) 18 23580 4 Retainer, Brush (Double) 18 23580 4 Retainer, Brush (Double) 18 23580 4 Retainer, Brush (Double) 18 23580 4 Retainer, Brush (Double) 19 23581 8 Retainer, Brush (Single) 19 23581 8 Retainer, Brush (Single) 19 23581 8 Retainer, Brush (Single) 19 23581 8 Retainer, Brush (Single) 19 23581 8 Retainer, Brush (Single) 20 44008 2 Washer, Flat 1-1/8" x .78" x .025" 20 44008 2 Washer, Flat 1-1/8" x .78" x .025" 20 44008 2 Washer, Flat 1-1/8" x .78" x .025" 20 44008 2 Washer, Flat 1-1/8" x .78" x .025" 20 44008 2 Washer, Flat 1-1/8" x .78" x .025" 21 62490 2 Sprocket / Gear 21 62490 2 Sprocket / Gear 21 62490 2 Sprocket / Gear 21 62490 2 Sprocket / Gear 21 62490 2 Sprocket / Gear 22 23573 2 Dust Cover 22 23573 2 Dust Cover 22 23573 2 Dust Cover 22 23573 2 Dust Cover 22 23573 2 Dust Cover 23 47046 2 Dowel Pin (Drive) 23 47046 2 Dowel Pin (Drive) 23 47046 2 Dowel Pin (Drive) 23 47046 2 Dowel Pin (Drive) 23 47046 2 Dowel Pin (Drive) 24 43655 2 Ring, Retaining 3/4" 24 43655 2 Ring, Retaining 3/4" 24 43655 2 Ring, Retaining 3/4" 24 43655 2 Ring, Retaining 3/4" 24 43655 2 Ring, Retaining 3/4" 25 1650-21 4 Ring, Retaining .594" 25 1650-21 4 Ring, Retaining .594" 25 1650-21 4 Ring, Retaining .594" 25 1650-21 4 Ring, Retaining .594" 25 1650-21 4 Ring, Retaining .594" 26 44007 6 Washer, Shim 1-1/8" x .594" x .025" 26 44007 6 Washer, Shim 1-1/8" x .594" x .025" 26 44007 6 Washer, Shim 1-1/8" x .594" x .025" 26 44007 6 Washer, Shim 1-1/8" x .594" x .025" 26 44007 6 Washer, Shim 1-1/8" x .594" x .025" 27 43182 4 Bolt, Hex 5/16-18 x 3/4" Lg. 27 43182 4 Bolt, Hex 5/16-18 x 3/4" Lg. 27 43182 4 Bolt, Hex 5/16-18 x 3/4" Lg. 27 43182 4 Bolt, Hex 5/16-18 x 3/4" Lg. 27 43182 4 Bolt, Hex 5/16-18 x 3/4" Lg. 28 141 4 Washer, Flat 1-1/2" x .375" x .062" 28 141 4 Washer, Flat 1-1/2" x .375" x .062" 28 141 4 Washer, Flat 1-1/2" x .375" x .062" 28 141 4 Washer, Flat 1-1/2" x .375" x .062" 28 141 4 Washer, Flat 1-1/2" x .375" x .062" 29 1540-31 4 Washer, Flat .78" x 1.25" x .06" 29 1540-31 4 Washer, Flat .78" x 1.25" x .06" 29 1540-31 4 Washer, Flat .78" x 1.25" x .06" 29 1540-31 4 Washer, Flat .78" x 1.25" x .06" 29 1540-31 4 Washer, Flat .78" x 1.25" x .06" 30 1038 2 Nut, Nylock 3/8-24 Thread 30 1038 2 Nut, Nylock 3/8-24 Thread 30 1038 2 Nut, Nylock 3/8-24 Thread 30 1038 2 Nut, Nylock 3/8-24 Thread 30 1038 2 Nut, Nylock 3/8-24 Thread 31 2674-32 2 Hub Cap 31 2674-32 2 Hub Cap 31 2674-32 2 Hub Cap 31 2674-32 2 Hub Cap 31 2674-32 2 Hub Cap 32 43894 2 Ring, Retaining 1/2" 32 43894 2 Ring, Retaining 1/2" 32 43894 2 Ring, Retaining 1/2" 32 43894 2 Ring, Retaining 1/2" 32 43894 2 Ring, Retaining 1/2" 33 43932 2 Bolt, Hex 3/8-24 x 3-1/2" Lg. 33 43932 2 Bolt, Hex 3/8-24 x 3-1/2" Lg. 33 43932 2 Bolt, Hex 3/8-24 x 3-1/2" Lg. 33 43932 2 Bolt, Hex 3/8-24 x 3-1/2" Lg. 33 43932 2 Bolt, Hex 3/8-24 x 3-1/2" Lg. 34 23400 2 Bushing, Spacer 34 23400 2 Bushing, Spacer 34 23400 2 Bushing, Spacer 34 23400 2 Bushing, Spacer 34 23400 2 Bushing, Spacer 35 43890 1 Sprocket, Ratchet R.H. (not shown) 35 43890 1 Sprocket, Ratchet R.H. (not shown) 35 43890 1 Sprocket, Ratchet R.H. (not shown) 35 43890 1 Sprocket, Ratchet R.H. (not shown) 35 43890 1 Sprocket, Ratchet R.H. (not shown) 36 43889 1 Sprocket, Ratchet L.H. 36 43889 1 Sprocket, Ratchet L.H. 36 43889 1 Sprocket, Ratchet L.H. 36 43889 1 Sprocket, Ratchet L.H. 36 43889 1 Sprocket, Ratchet L.H. 37 44137 4 Washer, 1/2" x 1" x .02" 37 44137 4 Washer, 1/2" x 1" x .02" 37 44137 4 Washer, 1/2" x 1" x .02" 37 44137 4 Washer, 1/2" x 1" x .02" 37 44137 4 Washer, 1/2" x 1" x .02" 38 44542 2 Chain, Roller 38 44542 2 Chain, Roller 38 44542 2 Chain, Roller 38 44542 2 Chain, Roller 38 44542 2 Chain, Roller 39 43661 4 Bolt, Hex 1/4-20 x 1" Lg. 39 43661 4 Bolt, Hex 1/4-20 x 1" Lg. 39 43661 4 Bolt, Hex 1/4-20 x 1" Lg. 39 43661 4 Bolt, Hex 1/4-20 x 1" Lg. 39 43661 4 Bolt, Hex 1/4-20 x 1" Lg. 40 62791 1 Housing, Wheel Drive Ass'y. L.H. 40 62791 1 Housing, Wheel Drive Ass'y. L.H. 40 62791 1 Housing, Wheel Drive Ass'y. L.H. 40 62791 1 Housing, Wheel Drive Ass'y. L.H. 40 62791 1 Housing, Wheel Drive Ass'y. L.H. 41 62792 1 Housing, Wheel Drive Ass'y. R.H. 41 62792 1 Housing, Wheel Drive Ass'y. R.H. 41 62792 1 Housing, Wheel Drive Ass'y. R.H. 41 62792 1 Housing, Wheel Drive Ass'y. R.H. 41 62792 1 Housing, Wheel Drive Ass'y. R.H. 42 48926 2 Tube, Upper Hopper Frame 42 48926 2 Tube, Upper Hopper Frame 42 48926 2 Tube, Upper Hopper Frame 42 48926 2 Tube, Upper Hopper Frame 42 48926 2 Tube, Upper Hopper Frame REPAIR PARTS LIST FOR MODEL 486.242112 - 42" HIGH PERFORMANCE LAWNSWEEPER REF. PART QTY. DESCRIPTION 43 47477 2 Tube, Rear Hopper Frame 44 48726 2 Tube, Lower Hopper Frame 45 24189 1 Strap, Bag Frame 46 43938 2 Rod, Hopper Support 34" 47 43737 1 Hopper Rope 48 48401 1 Hopper Bag 49 24191 1 Strap, Height Adjustment 50 23687 1 Bracket, Hitch 51 24192 1 Bracket, Hitch (Straight) 52 24193 1 Handle, Height Adjustment 53 46781 2 Tube, Bag Arm 54 46823 1 Rod, Hopper Bag Pivot 55 44985 2 Wheel & Tire Ass'y. (with bearings) 56 45088 4 Wheel Bearing 57 46782 2 Bolt, Hex 5/16-18 x 3" Lg. 58 43224 2 Bolt, Hex 5/16-18 x 2-1/4" Lg. 59 47810 8 Nut, Nylock 5/16-18 Thread 60 46847 1 Bushing, Spacer 61 43720 1 Knob, Wing 5/16-18 Thread 62 44326 1 Bolt, Carriage 5/16-18 x 1" Lg. 63 43081 1 Washer, Flat 5/16" Std. Wrt. 64 43084 4 Bolt, Hex 5/16-18 x 1-3/4" Lg. 65 43943 1 Grip, Height Adjust 66 44732 1 Washer, Tooth Lock 5/16" 67 49493 1 Pin, Hitch 68 23368 2 Tube, Hitch Spacer 69 43343 1 Hairpin Cotter, 1/8" 70 44917 2 Palnut, 3/8" 71 48402 4 Plug, 1/4" 72 48365 2 Pin, Clevis 1/4" x 1-1/8" 73 48366 2 Pin, Clevis 3/8" x 1/2" 74 44481 2 Cap, Vinyl 75 43055 6 Hairpin Cotter, 3/32" #3 76 46867 2 Pin, Clevis 1/4" x 1-1/2" Lg. 77 44230 1 Spring, Hitch Pin 78 142 1 Pin, Cotter 1/8" x 3/4" Lg. 79 49102 4 Screw, #12 x 1/2" Hex Head 80 43070 1 Washer, 3/8" Flat 81 C-9M5732 14 Rivet, Pop 49535 1 Owners Manual

For repair of major brand appliances in your own home… no matter who made it, no matter who sold it! 1-800-4-MY-HOMESM Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, day or night www.sears.com For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself, call Sears PartsDirect SM! 1-800-366-PART 6 a.m. – 11 p.m. CST, (1-800-366-7278) 7 days a week www.sears.com/partsdirect To purchase or inquire about a Sears Service Agreement: 1-800-827-6655 7 a.m. – 5 p.m. CST, Mon. – Sat. Para pedir servicio de reparación a domicilio, y para ordenar piezas con entrega a domicilio: 1-888-SU-HOGAR SM (1-888-784-6427) Au Canada pour service en français: 1-877-LE-FOYER SM (1-877-533-6937) © Sears, Roebuck and Co. ® Registered Trademark / ™Trademark of Sears, Roebuck and Co. ® Marca Registrada / ™Marca de Fábrica de Sears, Roebuck and Co. HomeCentral SM