Biketronics CribClicker BT385 Installation Manual

RECEIVER INSTALLATION CribClicker Installation Guide MADE IN USA BT385 Universal Fitment Features: • Open your garage door by fl ashing your high beams twice • Highly secure wireless device • Our Famous Lifetime Warranty CAUTION! When working on automatic garage door openers, make sure to follow the manufacturer’s safety instructions carefully. Please exercise good judgment. Unplug the garage door motor when making connections. Anticipate that opener may actuate at any time and use proper precautions. Congratulations on your Biketronics CribClicker purchase! CribClicker is made in America using components from American companies to the extent possible and whenever available. CribClicker is a state-of-the-art, highly secure wireless garage door and gate opener. Should you have questions regarding CribClicker, feel free to dial the number found in these instructions. Watch the installation video at biketronics.com or visit our YouTube channel 1. Disconnect power from door/gate motor. DO THIS NOW! 2. Locate BT385 RX receiver on wall switch circuit between wall switch and door motor. A good location is at door motor near the wall switch terminal strip. This may be behind light-lens or on back of power door motor. Contact Biketronics if you require assistance: Tel: 800-735-2419 E-Mail: [email protected] Web: www.biketronics.com Biketronics, Inc. 321 East Palouse River Drive Moscow, ID 83843 3. Use supplied Posi-Taps to make connection of CribClicker’s two black wires to wall switch circuit, or alternatively tap directly into the terminal strip. 4. Use zip-tie or Velcro to secure the CribClicker module. Note: Yellow wire is the antenna and should not be connected to anything. You may lengthen this wire to increase reception.

Updated 5-16-2013 TRANSMITTER INSTALLATION TEST AND FINISH ADDING A TRANSMITTER CLEARING RECEIVER MEMORY TROUBLESHOOTING 1. Disconnect battery - negative cable first. DO THIS NOW! 2. Remove outer fairing. 3. Connect and mount the transmitter: one wire to ground and one wire to switched 12V. Headlight high-beam circuit is best. (White wire on Harley Davidson - Consult your shop manual). 4. Use zip-tie or Velcro to secure the CribClicker module. 1. Reconnect battery cables on bike - positive cable first. 2. Be sure area around garage door is clear. Connect power to garage door. 3. Connect and mount the transmitter: one wire to ground and one wire to switched 12V. Headlight high-beam circuit is best. (White wire on Harley Davidson - Consult your shop manual). 4. Test CribClicker by clicking switch from low to high to low and back to high. After door operation, set switch back to low. 1. Connect the receiver to a power source: either garage door or power adapter mentioned in the troubleshooting section. Press and hold button on Receiver until LED light turns on and then off – release button. The receiver is now in pairing mode for the next 30 seconds. 2. Connect the Transmitter to a 9-volt battery. Open and close the circuit a few times until the LED on the receiver flashes first dim, and then bright. 3. Wait 30 seconds for receiver to leave pairing mode. Connect Transmitter to 9-volt battery again and open and close the circuit. Receiver will flash LED once and a click from the Receiver’s internal relay switch will be heard. Press and hold button on receiver. LED will flash once. Continue holding until LED lights on a second time. CribClicker is designed to work with almost every garage door and gate opener on the market. There are however, some openers that may require use of an external power adapter with your CribClicker receiver BT385 RX. You can obtain an inexpensive power adapter from RadioShack (P/N 273-025 or 273-313 AC-to- DC power adapter 6V 300 mA with tip set to negative). The purchase of a power adapter includes choice of free tip - use White “N” tip. (Note: Power adapter is only required if wall switch circuit voltage is less than 5 volts DC.) Metal shielding (such as a headlight bucket) around the transmitter may decrease effective system range. Position transmitter for acceptable performance. FCC Statement - This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instal- lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip- ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera- tion. Modifying or tampering with your Biketronics CribClicker BT385 can cause a malfunction, which might invalidate its warranty and void your FCC authorization to operate it.