ADJ Focus Spot 5Z User Instructions

Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical prod- ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you! ©2020 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their respective companies. ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product. DOCUMENT VERSION Due to additional product features and/or enhancements, an updated version of this document may be available online. Please check www.adj.com for the latest revision/update of this manual before beginning installation and/or programming. FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate radio frequency energy and, if not installed and used in accordance with the included instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following methods: · Reorient or relocate the device. · Increase the separation between the device and the receiver. · Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. 05/13/20 1 1.0.3 19/22/26 Initial Version Date Document Version Software Version > DMX Channel Mode Notes

Focus Spot 5Z Table of Contents Introduction Features I Warranty Registration Safety Guidelines Installation Overview DMX Set Up DMX Addressing DMX Modes & Values System Menu Dimmer Mode Chart I Dimmer Curve Chart Dimensional Drawings Gobo Replacement I Gobos Fuse Replacement I Multiple Unit Power Linking Trouble Shooting I Cleaning Limited Warranty (USA Only) Technical Specifications 3 4 5 8 10 11 13 14 20 26 27 28 29 29 30 31

Focus Spot 5Z Introduction Unpacking: Thank you for purchasing the Focus Spot 5Z by ADJ Products, LLC. Every unit has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support. Introduction: The Focus Spot 5Z is a DMX intelligent, moving head, LED fixture. This fixture can be used in a stand alone mode or connected in a Master/Slave configuration. This product is intended to be used by professionally trained personnel only and is not suitable for private use. Customer Support: Contact ADJ Service for any product related service and support needs. Also visit forums.adj.com with questions, comments or suggestions. Parts: To purchase parts online visit http://parts.americandj.com ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST Voice: 800-322-6337 | Fax: 323-582-2941 | [email protected] ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected] ADJ PRODUCTS LLC USA 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-2650 | Fax 323-532-2941 | www.adj.com | [email protected] ADJ SUPPLY Europe B.V Junostraat 2 6468 EW Kerkrade, The Netherlands +31 (0)45 546 85 00 | Fax +31 45 546 85 99 www.adj.eu | [email protected] ADJ PRODUCTS GROUP Mexico AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000 +52 (728) 282-7070 Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ Products, LLC. PLEASE recycle the shipping carton when ever possible.

Focus Spot 5Z Warranty Registration The Focus Spot 5Z carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre- paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con- tacting our customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number on the outside of the package will be returned to the shipper. ADJ Products, LLC - www.adj.com - Focus Spot 5Z User Manual Page 4 • Individual Color and Gobo Wheels • 2 x Color Wheels: 8 Colors + White (Each Wheel) • 6 Rotating Replaceable Gobos + Open • 2 Separate Frost Filters • 2 Separate Rotating Prisms (6 Facet Circular Prism & 5 Facet Linear Prism) • Adjustable Dimmer Modes, Dimming Speed, and Dimmer Curves • 5-Pin DMX Connections • 3 DMX Channel Modes: 19/22/26 • Electronic Dimming 0-100% • DMX-512 protocol • Multiple Unit Power Linking (See page 29) Included: 1 x Locking Power Cable 1 x Omega Bracket 1 x Safety Cable

Focus Spot 5Z Safety Guidelines • DO NOT TOUCH the fixture housing during operation. Disconnect the power and allow approximately 15 minutes for the fixture to cool down before servicing. • DO NOT shake the fixture, avoid brute force when installing and/or operating the fixture. • DO NOT operate the fixture if the power cord has become frayed, crimped and/or damaged. If the power cord is damaged, replace immediately with a new one of similar power rating. • DO NOT Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. • DO NOT attempt to operate this unit, if it becomes damaged. • DO NOT spill water or other liquids into or on to your unit. • This unit is intended for indoor use only, use of this product outdoors voids all warranties. • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture • Disconnect from main power before making any type of connection. • DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling. • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall. • During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. Thsi is a normal process and is caused by excess paint in the interior of the casing burning off from the heat. This will decrease gradually over time. • DO NOT remove the cover under any conditions. There are no user serviceable parts inside. • Never operate this unit when it’s cover is removed. • Never plug this unit in to a dimmer pack • During long periods of non-use, disconnect the unit’s main power. • Always mount this unit in safe and stable matter. • Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit. • Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 29 for cleaning details. • Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. • The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the fixture. C. The fixture has been exposed to rain or water. D. The fixture does not appear to operate normally or exhibits a marked change in performance. E. The fixture has fallen and/or subjected to extreme handling.

Focus Spot 5Z Safety Guidelines RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION! FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED. WEAR PROPER EYE AND SKIN PROTECTION. AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED. AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN. AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m). DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER. DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT. INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

Focus Spot 5Z Safety Guidelines POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers, which are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ lighting fixtures, can cause severe internal damage including burning to optics, dichroic color filters, glass and metal gobos, prisms, animation wheels, frost filters, iris, shutters, motors, belts, wiring, discharge lamps, and LEDs. This issue is not specific only to ADJ lighting fixtures, it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service for more details. DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

Focus Spot 5Z Installation Screw one clamp via a M12 screw and nut into the Omega bracket. Insert the quick-lock fasteners of the Omega bracket into the respective holes on the bottom of the Focus Spot 5Z. Tighten the quick-lock fasteners fully clockwise. Pull the safety cable through the opening located on the base plate and over the trussing system or a safe fixation spot. Insert the end in the carabine and tighten the safety screw. NOTICE: The suitable enviromental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above. This will allow the fixture to run at its best and help prolong the fixture life. OMEGA BRACKET CLAMP (Not Included) OMEGA BRACKET ATTACHMENT POINTS SAFETY CABLE ATTACHMENT POINTS

Focus Spot 5Z Installation The Focus Spot 5Z is fully operational in three different mounting positions, hanging upside-down from a ceiling or trussing, sideways on trussing, or set on a flat level surface. Be sure this fixture is kept at least 12m (40ft) away from any flammable materials (decoration etc.). Always use and install a safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails (see previous page). Never use the carrying handles for secondary attachment. When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit. Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic safety inspection of all installation material and unit. If you lack these qualifications, do not attempt the installation yourself. These installaiton should be checked by a skilled person once a year.

Focus Spot 5Z Overview 1. Service Port 2. LED Display 3. Mode Button Up Button Down Button Left Button Right Button Enter Button 4. Locking Power Connector In 5. Fuse Holder 6. Locking 5-Pin XLR Connector Out 7. Locking 5-Pin XLR Connector In 8. Locking Power Connector Out 1 3 2 4 5 6 7 8

Focus Spot 5Z DMX Set Up DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu- nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Spot 5Z can be controlled via DMX-512 protocol. The DMX address is set on the front panel of the Focus Spot 5Z. Your unit and your DMX controller require a 5-pin XLR connector for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split. Notice: Be sure to follow figures one (1) and two (2) when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX512 IN 3-PIN XLR SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND DMX512 DMX+,DMX-,COMMON 1 2 3 Termination reduces signal erro avoids signal transmission pr and interference. It is always ad to connect a DMX terminal, (Res 120 Ohm 1/4 W) between PIN 2 and PIN 3 (DMX +) of the last 1 2 3 1 2 3 DMX + DMX - COMMON DMX512 OUT 3-PIN XLR Figure 1 Figure 2 1 Ground 1 Ground XLR Male Socket XLR Pin Configuration 3 Hot 2 Cold 2 Cold 3 Hot XLR Female Socket Pin 3 = Data True (positive) Pin 2 = Data Compliment (negative) Pin 1 = Ground

Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior. Focus Spot 5Z DMX Set Up DMX512 IN 3-PIN XLR POWER POWER 1 2 3 Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. 1 2 3 Figure 3 5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. Conductor 5-Pin XLR Male (In) 3-Pin XLR Female (Out) Pin 1 Do Not Use Do Not Use Pin 3 Pin 2 Pin 1 Pin 3 Pin 2 Not Used Not Used Data True (+ signal) Data Compliment (- signal) Ground/Shield 3-Pin XLR to 5-Pin XLR Conversion

All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment of this starting DMX address is achieved by setting the correct DMX address on the digital control display on the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react in the same way, in other words, changing the settings of one channel will affect all the fixtures simultaneously. If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number you have set, based on the quantity of DMX channels of each fixture. That means changing the settings of one channel will only affect the selected fixture. In the case of the Focus Spot 5Z, when in 19 channel mode you should set the starting DMX address of the first unit to 1, the second unit to 20 (19 + 1), the third unit to 39 (20 + 19), and so on. (See the chart below for more details.) Focus Spot 5Z DMX Addressing Channel Mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address 19 Channels 1 20 39 58 22 Channels 1 23 45 64 26 Channels 1 27 53 79

Focus Spot 5Z DMX Modes & Values 1 1 PAN MOVEMENT (8-BIT) Pan Movement 2 PAN FINE (16-BIT) Fine Control of Pan Movement 3 3 TILT MOVEMENT (8-BIT) Tilt Movement 4 TILT FINE (16-BIT) Fine Control of Tilt Movement 5 5 COLOR WHEEL 1 Functions Standard (22) Extend (26) Values Open / White Red Orange Yellow Green Dark Blue Purple Light Blue Magenta Color Indexing Clockwise Rotation Fast - Slow No Rotation Counter-Clockwise Rotation Slow - Fast 000-007 008-014 015-021 022-028 029-035 036-042 043-049 050-056 057-063 064-127 128-189 190-193 194-255 000-255 000-255 000-255 000-255 Basic (19) 3 1 2 COLOR WHEEL 2 Open / White Lavender Blue CTB 5600 Green Yellow UV CTO 3200 Pink Color Indexing Clockwise Rotation Fast - Slow Stop Counter-Clockwise Rotation Slow - Fast 000-007 008-014 015-021 022-028 029-035 036-042 043-049 050-056 057-063 064-127 128-189 190-193 194-255 ADJ FOCUS SPOT 5Z DMX Channel Values & Functions Supports Software Version > 1.0.3 Feature subject to change without notice *Rotation direction (Clockwise/Counter-Clockwise) and control of effects depends on head orientation and Pan/Tilt settings* 6 6 4 2 4

Focus Spot 5Z DMX Modes & Values 7 7 GOBO WHEEL Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 1 Shake (Slow-Fast) Gobo 2 Shake (Slow-Fast) Gobo 3 Shake (Slow-Fast) Gobo 4 Shake (Slow-Fast) Gobo 5 Shake (Slow-Fast) Gobo 6 Shake (Slow-Fast) Clockwise Rotation Fast-Slow No Rotation Counter-Clockwise Rotation Slow-Fast 000-004 005-019 020-034 035-049 050-064 065-079 080-094 095-109 110-124 125-139 140-154 155-169 170-189 190-221 222-223 224-255 5 8 8 6 GOBO ROTATION Indexing Clockwise Rotation (Fast-Slow) No Rotation Counter-Clockwise Rotation Slow-Fast) 000-127 128-189 190-193 194-255 SHUTTER & STROBE Shutter Closed Shutter Open Strobe Slow-Fast Shutter Open Pulse Effect Slow-Fast Shutter Open Random Strobe Slow-Fast Shutter Open 000-031 032-063 064-095 096-127 128-159 160-191 192-223 224-255 9 9 7 Functions Standard (22) Extend (26) Values Basic (19) MASTER DIMMER 0%-100% 000-255 DIMMER FINE (16-BIT) 0%-100% 000-255 10 10 8 11

Focus Spot 5Z DMX Modes & Values PRISM 2 (5 FACET LINEAR) Open Shutter Open 000-031 032-255 PRISM 2 INDEXING & ROTATION Indexing Clockwise Rotation Fast-Slow No Rotation Counter-Clockwise Rotation Slow-Fast 000-127 128-189 190-193 194-255 PRISM 2 FINE INDEXING (16-BIT) 000-255 13 15 14 16 12 17 11 FOCUS Far-Near 000-255 ZOOM Minimum-Maximum Beam 000-255 FROST 1 0%-100% 000-255 FROST 2 0%-100% 000-255 15 18 13 16 19 14 21 18 22 16 17 15 ZOOM FINE INDEXING (16-BIT) 000-255 20 Functions Standard (22) Extend (26) Values Basic (19) PRISM 1 (6 FACET CIRCULAR) Open Shutter Open 000-031 032-255 PRISM 1 INDEXING & ROTATION Indexing Clockwise Rotation Fast-Slow No Rotation Counter-Clockwise Rotation Slow-Fast 000-127 128-189 190-193 194-255 PRISM 1 FINE INDEXING (16-BIT) 000-255 11 12 9 12 13 10 14

Focus Spot 5Z DMX Modes & Values DIMMER CURVES Linear Square Inverse Square S-Curve No Function 000-020 021-040 041-060 061-080 081-255 PAN/TILT SPEED Fast-Slow 000-255 20 24 21 25 18 Functions Standard (22) Extend (26) Values Basic (19) DIMMER MODES: Standard Stage TV Architectural Theatre Stage 2 DIMMING SPEED 0.1Sec. 0.2Sec. 0.3Sec. 0.4Sec. 0.5Sec. 0.6Sec. 0.7Sec. 0.8Sec. 0.9Sec. 1.0Sec. 1.5Sec. 2.0Sec. 3.0Sec. 4.0Sec. 5.0Sec. 6.0Sec. 7.0Sec. 8.0Sec. 9.0Sec. 10Sec. Default to Unit Setting 000-020 021-040 041-060 061-080 081-100 101-120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141-255 19 23

Focus Spot 5Z DMX Modes & Values 22 26 19 LED REFRESH RATE & SPECIAL FUNCTIONS Default LED Refresh Rate 1200Hz Refresh Rate (Hz) 900 910 920 930 940 950 960 970 980 990 1000 1010 1020 1030 1040 1050 1060 1070 1080 1090 1100 1110 1120 1130 1140 1150 1160 1170 1180 1190 1210 1220 1230 1240 1250 1260 1270 1280 1290 1300 1310 1320 1330 1340 1350 1360 1370 1380 1390 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Functions Standard (22) Extend (26) Values Basic (19) 000-010 011-078

Focus Spot 5Z DMX Modes & Values 22 26 19 LED REFRESH RATE & SPECIAL FUNCTIONS 1400 1410 1420 1430 1440 1450 1460 1470 1480 1490 1500 2500 4000 5000 6000 10,000 15,000 20,000 25,000 Disable LED Refresh Rate Enable Blackout with Pan/Tilt Movement Disable Blackout with Pan/Tilt Movement Enable Blackout with Color Change Disable Blackout with Color Change Enable Blackout with Gobo Change Disable Blackout with Gobo Change Reset All Reset Pan/Tilt Reset Color & Gobo Reset Effect & Focus Internal Program 1 (Scenes 1-8) Internal Program 2 (Scenes 9-16) Internal Program 3 (Scenes 17-24) Internal Program 4 (Scenes 25-32) Internal Program 5 (Scenes 33-40) Internal Program 6 (Scenes 41-48) Internal Program 7 (Scenes 49-56) Fan Mode Low Fan Mode High Fan Mode Auto No Function 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 080-089 090-099 100-109 110-119 120-129 130-139 140-149 150-159 160-169 170-179 180-185 186-191 192-197 198-199 200-205 206-211 212-216 217-227 228-238 239-249 250-255 Functions Standard (22) Extend (26) Values Basic (19)

Focus Spot 5Z System Menu SYSTEM MENU The fixture includes an easy to navigate system menu control panel display where all necessary settings and adjustments are made. During normal operation, pressing the MODE button once will access the fixture’s main menu. Once in the main menu, you can navigate through the different functions with the UP and DOWN buttons. When you reach a field that requires adjusting, press the ENTER button to access that field and use the LEFT and RIGHT buttons to adjust the field. Pressing the ENTER button once more will confirm your setting. You may exit the main menu at any time without making any adjustments by pressing the MODE button. System Menu Access: To access the system menu when the fixture is not powered using the internal battery, press and hold the MODE button to illuminate the LCD screen until the DMX address is displayed. Then navigate to the desired system menu. LCD CONTROL PANEL LOCKOUT When the Key Lock function is activated, the control panel will automatically lock after the time set under the Display submenu “Screen Saver Delay”. When the Key Lock function is set to ON, the control panel will lock. Press and hold the MODE button for 3 seconds to unlock. When the Key Lock function is set to ON1, the control panel will lock, and will not unlock without a code. To unlock the display follow these steps: 1. Press the UP button, and the display will change to: (one * appears). 2. Press the DOWN button, and the display will change to: (two * appear). 3. Press the UP button, and the display will change to: (three * appear). 4. Press the DOWN button, and the display will change to: (four * appear). 5. Press the ENTER buttton, and the display will be unlocked. If the button sequence was entered correctly, the display and control panel will unlock. If the button sequence was entered incorrectly, the display will return to the DMX addess display. * * * * * * * * * *

Focus Spot 5Z System Menu DMX SETTINGS 001-XXX Pan/Tilt Movement Feedback DMX Lost Status DMX Channel Mode Selection DMX Addressing Basic (19) / Standard (22) / Extended (26) MENU OPTIONS DESCRIPTION SUBMENU Pan/Tilt Movement Speed Reverse Tilt Motion Set Address DMX Channel Mode No DMX Status Hold Last / Blackout / Manual PERSONALITY Status Settings Pan Invert: ON / OFF Tilt Invert: ON / OFF P./T. Feedback: ON / OFF P./T. Speed: Speed 1 / Speed 2 Hibernation: Off / 01M~99M / 15M Reverse Pan Motion Sleep Setting (No Activity) Fan Settings Head Fan: Auto / High / Silent (Low) Reset Motors Reset All Motors: YES / NO Pan/Tilt Reset: YES / NO Effect/Focus Reset: YES / NO Reset All Motors Reset Pan/Tilt Motors Reset Effect/Focus Motors Dim Modes Dimming Modes Dimming Speed Standard/Stage/TV/Architectur/Theatre/Stage2 Dim Speed: 0.1-10s LED Refresh Rate 1200 / 900-1500 / 2500 / 4000 / 5000 / 6000 10000 / 15000 / 20000 / 25000 (Hz) LED Refresh Setting Display Intensity: 1~10 (Dimmest-Brightest) Display Invert: YES / NO Screen Saver Delay: OFF~10M Display Intensity Adjustment Display Inversion Display Shutoff Time Fan Speed Setting Key Lock: OFF / ON / ON1 Display Control Lock Service USB Port Power: ON / OFF Update Software: YES / NO Factory Restore: YES / NO (Pass Code = 11) Calibration Adjustment USB Port Activation Software Update Restore Factory Settings Pass Code = 050 Effect Adjust (Calibration) (Pass Code = 50) Pan Degree: 630 / 540 Pan Degree Selection Color/Gobo Reset: YES / NO Reset Color/Gobo Motors Dim Curve Linear / Square / Inverse Square / S-Curve Dimming Curves Master Setting Master ON / OFF Slave Setting Slave ON / OFF

Focus Spot 5Z System Menu MENU OPTIONS DESCRIPTION SUBMENU MANUAL CONTROL Manual Control Settings Pan Pan Fine Tilt Tilt Fine Color 1 Color 2 Gobo Gobo Rot Shutter Dimmer Dimmer Fine Prism 1 Prism 1 Rot. Prism1Rot Fine Prism 2 Prism 2 Rot. Prism2Rot Fine Focus Zoom Zoom Fine Frost 1 Frost 2 Dim Modes Dim Curves P/T Speed Special Function 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 000-255 INTERNAL PROGRAMS Program 1 Program 2 Program 3 Program 4 Program 5 Program 6 Program 7 Program 1 with Adjustments Program 2 with Adjustments Program 3 with Adjustments Program 4 with Adjustments Program 5 with Adjustments Program 6 with Adjustments Program 7 with Adjustments Speed: 000~255 Fade: 000~255 Speed: 000~255 Fade: 000~255 Speed: 000~255 Fade: 000~255 Speed: 000~255 Fade: 000~255 Speed: 000~255 Fade: 000~255 Speed: 000~255 Fade: 000~255 Speed: 000~255 Fade: 000~255

Focus Spot 5Z System Menu INFORMATION MENU OPTIONS DESCRIPTION SUBMENU Fixture Life Time Total LED Time Fixture Temps Total Running Time (Not Resettable) Total Running Time (Resettable) Reset Total Running Time Total LED On Running Time (Not Resettable) LED On Running Time (Resettable) Reset LED Running Time Fan Info. (RPM) LED Fan1: XXXX RPM LED Fan 1 Speed Reset LED Temperature (Max Resettable) Reset Lamp Temp: YES / NO (Pass Code = 050) Current Head Temperature Maximum Temperature(1) Reached (Resettable) (See Note 1) Maximum Temperature(2) Reached (Not Resettable) (See Note 2) LED’s Current: XXX ˚F / XXX ˚C Max Resettable: XXX ˚F / XXX ˚C Max Not Resettable: XXX ˚F / XXX ˚C Power On Time: XXXXXX Hours P-On Time-R: XXXXXX Hours P-On Time-Reset: YES / NO Pass Code = 50 LED On Time: XXXXXX Hours LED On Time-R: XXXXXX Hours LED Hours Reset: YES / NO Pass Code = 50 Error Logs Fixture Errors Reset Error Log - Pass Code = 50 List of Errors (One by One) Clear the Error Log Software Version VX.X Current Software Version DMX Values Pan / Pan Fine / Tilt / Tilt Fine / Color 1 / Color 2 / Gobo / Gobo Rot / Shutter / Dimmer / Dimmer Fine / Prism 1 / Prism 1 Rot / Prism1Rot Fine / Prism 2 / Prism 2 Rot/ Prism2Rot Fine / Focus / Zoom / Zoom Fine / Frost 1 / Frost 2 / Dim Modes / Dim Curves / P/T Speed / SpecialFunction Current DMX Values(3) (See Note 3) Notes: (1) Current Maximum Temperature - Maximum fixture temp. that has been recorded, before reset and after reset. (2) Maximum Temperature - Overall maximum fixture temp. that has been recorded. (Not Resettable) (3) DMX Value options depend on the current DMX Channel mode setting. LED Fan2: XXXX RPM LED Fan 2 Speed

Focus Spot 5Z System Menu DMX SETTINGS - The submenus listed under DMX SETTINGS are as follows: Set Address, DMX Channel Mode, and No DMX Status. - SET ADDRESS - In this submenu you can find and set your desired DMX address. - DMX CHANNEL MODE - In this submenu you can find and set your desired DMX channel mode. - NO DMX STATUS - This submenu setting is used as a precaution mode in case the DMX signal or power is lost or interrupted. The operating mode chosen in this submenu is the running mode the fixture will go into when the DMX signal is lost. Listed below are the 3 modes. • Hold Last - This setting will have the fixture stay in the last DMX setup. • Blackout - This setting will have the fixture automatically go into stand by/blackout mode. • Manual - This setting will go into the current manual control set up. See MANUAL CONTROL. PERSONALITY - The submenus listed under PERSONALITY are as follows: Master & Slave Settings, Status Settings, Fan Settings, Dim Modes, LED Refresh Rate, Dimf Curves, Reset Motors, Display, and Service. - MASTER & SLAVE SETTINGS - In this submenu you are able to designate the units as either “Master” or “Slave” unit in a master-slave set up. - STATUS SETTINGS - In this submenu you are able to access and adjust/change: Pan Degree, Pan Invert, Tilt Invert, P./T. Feedback, P./T. Speed, and Hibernation. - FAN SETTINGS - In this submenu you are able to select your desired fan speed setting. - DIM MODES - In this submenu you are able to select your desired dimmer mode and adjust the dimming speed time. See the dimmer mode chart on page 26 for more information. - LED REFRESH RATE - In this submenu you are able to select your desired LED refresh rate. - DIM CURVE - In this submenu you are able to select your desired dimmer curve. See the dimmer curve chart on page 26 for more information. - RESET MOTORS - In this submenu you are able to reset selected motors. - DISPLAY - In this submenu you you are able to adjust the display intensity, invert the display, set the display lock time, and activate/deactivate the display lock. - SERVICE - In this submenu you are able to access and adjust/change: calibration (effect adjust), activate/deactivate the USB port power, update the software, and restore the factory settings. MANUAL CONTROL - This menu is for manual testing and manual control. INTERNAL PROGRAMS - In this menu you are able to select 1 of 7 internal programs to run. Program running speed and fade speed are adjustable.

Focus Spot 5Z System Menu INFORMATION - The submenus listed under INFORMATION are as follows: Fixture Life Time, Total LED Time, Fixture Temps, Fan Info. (RPM), DMX Values, Error Logs, and Software Version. - FIXTURE LIFE TIME • Power On Time -The TOTAL power ON running time of the unit is displayed. This time CANNOT be reset. • P-On Time-R - The CURRENT power ON running time of the unit is displayed. This running time may not be the same as the TOTAL power ON running time displayed under “Power On Time”. This time CAN be reset. NOTE: The displayed time represents the current power ON time since the last reset. • P-On Time-Reset - With this function you can reset the CURRENT power ON running time that is displayed under “P-On Time-R”. - TOTAL LED TIME • LED On Time - The TOTAL LED ON time is displayed. This total LED ON time CANNOT be reset. • LED On Time-R - The CURRENT LED ON running time is displayed. This running time may not be the same as the TOTAL LED ON time displayed under “LED On Time”. This current LED ON time CAN be reset. NOTE: The displayed time represents the current LED ON time since the last reset. • LED Hours Reset - With this function you can reset the CURRENT LED ON time that is displayed under “LED On Time-R”. - FIXTURE TEMPS • LED’s: • Current - The current LED temperature will be displayed. • Max Resettable - The current highest temperature the LED has reached will be displayed. This LED temperature may not be the same as the temperature displayed under “CURRENT” or “MAX NOT RESETTABLE”. This LED temperature CAN be reset. NOTE: The displayed temperature represents the highest temperature the LED has reached since the last reset. • Max Not Resettable - The highest temperature the LED has reached will be displayed. This LED temperature CANNOT be reset, and could continue rise. • RESET LED TEMP - With this function you can reset the “MAX RESETTABLE” LED temperature. NOTE: When the temperature is reset, the temperature will revert to the CURRENT LED temperature. - FAN INFO. (RPM) - In this submenu the current fan speed’s will be displayed. - DMX VALUES - Displays the DMX values of any DMX channel that is currently in use. NOTE: DMX value options depend on the current DMX channel mode setting. - ERROR LOGS - In this submenu you are able to check any unit errors as well a clear the error log. - SOFTWARE VERSION - Current software version is displayed.

Focus Spot 5Z Dimmer Mode Chart DIMMER 100% 50% 10% 0% Time (ms) 0 Sec 255 255 0 0 Standard (default) 0 0 0 0 Stage 780 1100 1540 1660 TV 1180 1520 1860 1940 Architectural 1380 1730 2040 2120 Theatre 1580 1940 2230 2280 Stage 2 0 1100 0 1660 Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms) Rise Time Down Time Dimming Curve Ramp Effect 0 sec Fade Time 1 sec Fade Time Focus Spot 5Z Dimmer Curve Chart Output 0 100% Output 0 100% Output 0 100% Output 0 100% DMX % DMX % DMX % DMX % LINEAR SQUARE INVERSE SQUARE S-CURVE

Focus Spot 5Z Gobo Replacement The gobo’s featured in this unit are interchangable. Remember when changing these gobo’s that they are thin and easy to bend. If your removing/replacing the glass gobo, please be very careful. REMEMBER, this is a glass gobo, it is delicate. Please be very careful when removing/replacing any of the gobo’s. Caution! Never open the unit when in use. Always disconnect the main power before attempting to change the gobos. Locating the Gobo wheel: After disconnecting the main power, position the head with the lens facing forward. When looking through the front lens, position the head so that the frost filters are located at the top (see image below). When the frost filters are located at the top, the shell that needs to be uscrewed and removed is now facing up. 1. To change a gobo, uscrew the 4 screws that secure the shell to the unit. Gently lift and remove the shell. 2. Once the shell is removed, you will be able to access the gobo wheel. Turn the wheel until you come across the gobo you would like to change. 3. Once you have found the gobo you would like to change, use your finger to carefully turn the small inner gear so that the “alignment dot” on the inner gear, lines up with the gobo you would like to replace (Figure 1). 4. Once the gobo and “alignment dot” are lined up, CAREFULLY, from underneath the gobo wheel, push the gobo housing with gobo up and pull the housing out. CAUTION! Do not put to much pressure on the gobo itself due to the fact it is thin and it can bend. 5. Using your fingernail or needle nose pliers, CAREFULLY remove the retainer ring that secures the gobo in place. After the retainer ring is removed, your are able to remove the gobo (Figure 2). 6. Change the gobo and replace the retainer ring. NOTE: The black side of the gobo faces outwards in the gobo holder. 7. To reinsert the gobo housing back into the gobo wheel, make sure the “alignment dot” lines up with the “protruding pin” (Figure 3). The “protruding pin” secures the gobo housing to the gobo wheel. You will feel the gobo housing “lock” into place when the housing is inserted correctly. 8. Reassemble the unit. FROST FILTER FROST FILTER

Focus Spot 5Z Gobo Replacement Focus Spot 5Z Gobos GOBO 1 GOBO 5 GOBO 3 GOBO 4 GOBO 2 GOBO 6 (FIGURE 1) INNER GEAR “ALIGNMENT DOT” INNER GEAR (FIGURE 2) (FIGURE 3) PROTRUDING PIN PROTRUDING PIN INNER GEAR “ALIGNMENT DOT” INNER GEAR “ALIGNMENT DOT”

Focus Spot 5Z Dimensional Drawing 174mm / 6.85” 278.61mm / 10.97” 463.45mm / 18.25” 333.75mm / 13.14” 230.36mm / 9.07” 174mm / 6.85” 182.37mm / 7.18” 93.7mm / 3.69” 107mm 4.21” 75.15mm / 2.96” *NOT TO SCALE

Focus Spot 5Z Trouble Shooting Focus Spot 5Z Cleaning Listed below are a few common problems the user may encounter, with solutions. Unit not responding to DMX: 1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected. Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be car- ried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Clean the external optics with glass cleaner and a soft cloth every 20 days. 3. Always be sure to dry all parts completely before plugging the unit back in. Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog resi- due, dust, dew). Focus Spot 5Z Multiple Unit Power Linking With this feature you can connect the fixtures to one another using the power cable input and output sockets. NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES AS THE POWER CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON THIS FIXTURE! CHECK SILK SCREEN FOR MAX AMPS. Focus Spot 5Z Fuse Replacement Unplug the unit from any power source it may be connected to. Once the power has been disconnected, use a flat head screw driver to unscrew the fuse holder located next to the power input. Remove the bad fuse and replace with a new one, and screw the fuse holder back in.

MANUFACTURER’S LIMITED WARRANTY A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect. E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. MANUFACTURER’S LIMITED WARRANTY PERIODS: • Non L.E.D. Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps) • Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited warranty) • L.E.D. Products = 2-year (730 days) Limited Warranty (excluding batteries which have a 180 day limited warranty). Note: 2 Year Warranty only applies to purchases within the United States. • StarTec Series = 1 Year Limited Warranty (excluding batteries which have a 180 day limited warranty). • ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty

Model: Focus Spot 5Z Voltage: 100V ~ 240V/50~60Hz LEDs: 1 x 200W LED Working Position: Any safe working position Power Draw: 280W Fuse: 3A Dimensions: 7.15” (L) x 10.97” (W) x 18” (H) 181.5 x 278.61 x 457.4mm Weight: 23lbs. / 10 kgs Colors: Color Wheel 1: 8 Colors + White Color Wheel 2: 8 Colors + White Gobos: 6 Gobos (1 Glass) + Open Aluminum Gobos: Inner Diameter: 19mm Outer Diameter: 23mm Thickness: 0.5mm Glass Gobo: Inner Diameter: 19mm Outer Diameter: 23mm Thickness: 3.3mm DMX Channels: 3 DMX Modes: 19/22/26 Warranty: 2 Year (730 days) Please Note: Specifications and improvements in the design of this unit and this manual are subject to change.