EcoFlow RIVER Pro Operation & User’s Manual

and the accessories dry and do not expose them to high heat. 2. Never disassemble, puncture, shock, crash, or incinerate the product. 3. Recycle and dispose of RIVER Pro in accordance with the local regulations. 4. Pay attention to safety when handling the RIVER Pro. 5. Children or people with disabilities should use the machine under the protection of the supervisor. EcoFlow RIVER Pro

by improper operation. Read the ENTIRE user manual to be familiar with the features of this product before operating. Failure to operate the product correctly may result in damage to the product or personal property and cause serious injury. EcoFlow will not assume any legal responsibility. DO NOT use the product with incompatible components or alter the product in any way without following the instructions provided by EcoFlow. Otherwise, you cannot get after-sales service from EcoFlow under warranty condition. These Safety Guidelines include instructions for safety, operation and maintenance. It is important to read and follow all the instructions and warnings in the user manual before assembly, setup or use the product. Product Use: Product Safety Guidelines Glossary NOTICE CAUTION WARNING WARNING WARNING 1. DO NOT expose the product to any liquids. Do not immerse the product in water. DO NOT leave the batteries out in the rain or near a source of moisture. Moisture in the device could cause short circuits, component failure, fires or even an explosion. 2. Never use NON-EcoFlow parts. Go to http://www.EcoFlow.com to purchase new parts. EcoFlow takes no responsibilities for any damages caused by the use of non-EcoFlow parts. 3. Never install or remove other modules from the RIVER Pro when it is turned on. Do Not plug or unplug other modules when the power of the product is turned on, otherwise the power interface may be damaged. 4. Using the product in environments above 140ºF (60°C) may cause fire or explosion. Using the product in envi- ronments below -4ºF (-20°C) will severely affect the performance of the product. Allow the product to return to a normal operating temperature before use it. 5. DO NOT use the batteries in strong electrostatic or electromagnetic environments. Otherwise, the battery control board may malfunction and cause a serious accident during use. 6. Never disassemble or pierce the product in any way. Otherwise, it may leak, catch on fire, or explode. 7. DO NOT use the product if it was involved in a crash or a heavy bump. 8. If the product falls into the water during use, take the product out immediately and put it in a safe and open area. Keep a safe distance from it until it is completely dry. Never use it again and dispose it properly as described in the Battery Disposal section below. If the product catches fire, it is recommended to use fire extinguishing equipment in the following order: water or water mist, sand, fire blanket, dry powder, carbon dioxide fire extinguisher. 9. DO NOT put the machine in a microwave oven or in a pressurized container. The instructions, if not properly followed, may result in property damage and minor physical damage. The instructions, if not properly followed, may result in property damage and serious physical damage. The instructions, if not properly followed, may result in property damage, major accident and serious injury. Improper use may result in fire, property damage or personal injury. Make sure to use the product according to the following safety rules and guidelines.

Product Storage and Transportation: Product Charging: You are now an EcoFlow product user. This brief pamphlet is meant to help you. Please take some time to read it before using the product. Read it through to fully understand how to use the product! RIVER Pro Use Care and Safety Guide CONGRATULATIONS! 10. Do Not allow pins, wires or other metal pieces to insert to the device case, outlets or controls. Metal pieces may short circuit the product. 11. Avoid collision. DO NOT place heavy objects on the machine. 12. If there is dirt on any plug or outlet surface, use a dry cloth to clean it. Otherwise, it will cause abrasion and result in energy loss or inability to charge. 1. Always use EcoFlow approved charging cables. EcoFlow does not take any responsibility for any damages caused by using non-EcoFlow charging cables. 2. When charging, please place the product on the ground with no flammable or combustible materials around. To prevent accidents, never leave the machine unattended during charging. 3. DO NOT charge the product immediately after a long heavy load, because the product temperature may be- come too high. DO NOT charge the product until it cools down to room temperature. Do Not bring this product on flights. 1. Dispose of the product in specific recycling boxes only after a complete discharge. Batteries are hazardous chemicals. Please strictly follow your local regulations regarding the battery disposal and recycling. 2. Dispose of the product immediately if it cannot be powered on after over-discharging. 1. Temperature for normal use and storage of this product is -4°F to 113°F (-20°C to 45°C) and temperature for optimal use and storage of this product is 68°F to 77°F (20°C to 25°C). Cold weather use Cold temperatures (below freezing) can affect the unit’s battery capacity due to chemical characteristics of the battery. Keep the power station within the environment temperature range, -4 to 113°F (-20 to 45°C) to prolong battery life 2. If the product is not used for a long time, the battery life may be reduced. 3. Discharge EcoFlow RIVER Pro to 30%, then charge to 85% every 3 months to keep the battery healthy. 1. Keep the product out of the reach of children. If any children accidentally swallow parts, please see a doctor immediately. 2. If a low-battery warning appears, charge the product before storing it. Otherwise, long-term storage may cause damage to the batteries in the product. Batteries in the product will enter hibernation mode if they are depleted and stored for a long time. Recharging the product can bring the battery out of hibernation. 3. DO NOT place the product near a heat source, such as a car in direct sunlight, a fire source, or a heating stove. 4. Store the product in dry environments. Please keep the machine away from water. 5. Make sure no objects can fall on or around the product while it is being stored. 6. Never ship a product with a battery power level higher than 30%.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Orient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. NOTICE NOTICE To turn RIVER Pro on or off, you need to PRESS and HOLD the ON/OFF system Power Button. To turn on the AC power outlet, you need to PRESS and HOLD the AC Button after turning on RIVER Pro. We set the AC power button for users to turn off AC power when they don’t need it and save power. Please follow this intro- duction step-by-step to be familiar with each of RIVER Pro’s ports, buttons, display screens and more. Please fully charge (100%) your RIVER Pro before use it.

1 2 4 8 9 10 13 14 14 Features of the RIVER Pro LCD Display Introduction Solar Panel Connection Entry-Level UPS AC X-Boost Mode RIVER Pro and RIVER Pro Extra Battery Connection Technical Specifications How to Recharge RIVER Pro FAQs What’s in the Box CONTENTS 11 12

You may also use your mobile phone to scan this QR code or enter the download link in your browser: https://ecoflow.com/pages/ecoflow-app 1. Download the EcoFlow App EcoFlow App Download Guide 2. For more information about the App, please follow the instruction on the App or our official website www.ecoflow.com.

Charge a wide array of devices such as your iPhone, tablet, GoPro, speakers, or anything else that could be charged through USB Port. The USB output icon will appear on the LCD display when a USB port is in use. 1. LCD Display 220-240V region*Dedicated AC Output 2. USB-A Output Ports Features of the RIVER Pro *EcoFlow has designed different AC output sockets following the local regulations of different countries. 7 9 8 11 10 15 14 13 12 16 1 2 3 6 5 4 1. LCD Display 2. USB-A Output Ports 3. ON/OFF Button of LED Light 4. IOT Reset Button (PRESS & HOLD 3s to reset Wi-Fi) 5. USB-C 100W Output Port 6. Power Button & LCD Display Screen ON/OFF Power Indicator 7. DC Output ON/OFF Button (Car Outlet, 2 DC 5521 Output Ports) & DC Output Indicator 8. Fast Charge USB-A Output Port 9. AC Power Button (PRESS for ON/ OFF) AC Output Indicator 10. 3 AC Output Sockets (100-120V) 2 AC Output Sockets (220-240V) 12. X-Stream Charging Input Port 13. Overload Protection Switch 14. Solar Charge/Car Charge Input Port 15. Power Earth Screw 16. Expansion Power Port 11. Ventilation Fan Expansion Power Port

4. IOT Reset Button (PRESS & HOLD 3s to reset Wi-Fi) 5. USB-C 100W Output Port 6. Power Button & LCD Display Screen ON/OFF Power Indicator 7. DC Output Port (Car Outlet, 2 DC 5521 Output Ports) DC Output Indicator 8. Fast Charge USB-A Output Port 9. AC Power Button AC Output Indicator 10. 3 AC Output Sockets (100-120V) / 2 AC Output Sockets (220-240V) 11. Ventilation Fan There’re three types of LED light: low light, strong light, and SOS rescue signal flash. Press it once to turn on the low light; press it twice to turn on the strong light; press it one more time to turn on the SOS rescue signal flash; then press it again to turn off the LED light. Long press can turn off the LED directly. When you first use IOT function or you are changing the network environment, you need to press and hold IOT Reset button for 3 seconds to reset the Wi-Fi. It can connect with the mobile phone, then reconfigure the wireless network through the APP. When using the IOT mode, make sure the power station has sufficient amount of power or is connected to a power source to keep IOT standby. Devices that charge through a USB-C port, such as a MacBook Pro, Android phone, can be charged by the RIV- ER Pro USB-C port. The USB-C Output icon will appear on LCD Display when a USB port is in use. The USB-A output icon will appear on the LCD display when a USB-A port is in use. Fast charge-enabled devic- es can be charged at a maximum speed of 28W. If your device does not support fast charging, the device will charge in a normal speed. The AC power button controls the AC output of the RIVER Pro. The AC power needs to be turned on manually. To enable AC power, press the AC power button. When AC power is not in use to charge a device, press the AC power button to turn off the AC power. Make sure to unplug the power cord from the AC port. When the AC power of the RIVER Pro is enabled, the AC indicator will light up. If the AC power is not used for more than 12 hours, the AC ports will turn off automatically. Charging devices that require a 220-240V (220-240V region)/100-120V (100-120V region) wall charger such as laptops, TVs, mini-refrigerators, vacuums, etc. The X-Boost feature enables the 600W inverter to support 600W to 1200W devices by lowing the power required. This function does not support all electrical devices with higher power rating, please test to confirm before use. Press DC ON/OFF to turn on or off RIVER Pro DC power. The DC power button controls the RIVER Pro's car charger output and two direct currents (DC 5521) outputs. The car charger output supports an output up to 10A, which is sufficient to power most electrical appliances use in vehicles (such as mini-refrigerator). When the DC ON/OFF is on, the devcie will never shut down. Press and hold the system power button to turn RIVER Pro on or off. When RIVER Pro is turned on, the power indicator is in breathing mode, and the display is on; When the RIVER Pro is running, you can switch on or off the display screen by pressing the Power Button once. when RIVER Pro senses that any output port is in use, the display will automatically light up. The RIVER Pro screen will enter into the sleep mode after being in idle for more than 5 minutes, but the battery will still be running. The system standby time is 2 hours by default. You can set up the system standby time and screen standby time via the App. The fan prevents RIVER Pro from overheating. Please make sure nothing blocks the vents at both ends of the RIVER Pro.

the port and connect the cable to an AC power source. The U.S. and Japanese version supports 100Vac-120Vac (50Hz/60Hz)/international version supports 220Vac-240Vac (50Hz/60Hz) charging. RIVER Pro's X-Stream system supports an entry-level UPS function, and user can use the RIVER Pro AC socket while the device is con- nected to a wall socket with AC power supply (the AC power comes from the grid, not the battery). When the grid loses power suddenly, the device can automatically switch to be powered by RIVER Pro in <30ms. This is an entry-level grade UPS function that does not support 0ms switching. Do not connect devices with high uninter- rupted power supply requirements. Perform multiple tests to confirm compatibility before connecting devices such as data servers and workstations with RIVER Pro. EcoFlow will not be responsible for any loss of data or equipment damages caused by customers’ failure in following the instruction. When the input current continuously exceeds 10A during a charge, the AC charging port will trigger the overload protection (the Overload Protection Switch button will automatically pop out). When the device is confirmed to be normal, press the overload protection switch button to continue charging. Plug in the Expansion Power Cable into this port to connect your RIVER Pro to a RIVER Pro Extra Battery to expand the battery capacity to 1440Wh. 12. X-Stream Charging Input Port 13. Overload Protection Switch 14. Solar Charge/Car Charge Input Port 16. Expansion Power Port LCD Display Connect at most two 110W solar panels in parallel to recharge RIVER Pro. RIVER Pro supports a maximum solar input of 200W. RIVER Pro supports 12V car charge up to 10A. (Remember to start the engine when you charge via car charge, otherwise, the car battery may be drained.) Do not use the same cigaratte lighter port to charge other devices when recharging RIVER Pro. 15. Power Earth Screw For safety concern, some eletrical appliances need to be grounded. The power earth screw provides an option to get your RIVER Pro grounded using a grounding cable. i j k l m n o p

e. Low Temperature Indicator f. Fan Indicator g. Current Input h. Current Output i. Overload Warning Port Usage Indicators The RIVER Pro fan speed is intelligently controlled by the RIVER Pro, and the displayed speed is related to the fan speed. Shows the current input power of RIVER Pro in watts. Shows the current output power of RIVER Pro in watts. The overload icon and corresponding icon indicate the corresponding overload module. Shows the percentage of the power. If it displays 0%, please charge RIVER Pro immediately. b. Battery Level Indicator c. Battery Level Percentage Shows the remaining power. The icon rotates while charging. When the temperature of the RIVER Pro is too high, a high-temperature warning icon appears on the screen to warn that the temperature of the product is too high. Please cool down the product. When the temperature of the RIVER Pro is too low, a low-temperature warning icon appears on the screen to warn that the temperature of the product is too low. Please warm up the product properly before use. Battery Indicator Refers to the battery The number indicates the remaining charge/discharge time (in minutes) for RIVER Pro. a. Remaining Charge/Discharge Time When the SOC (State of Charge) is set in the EcoFlow App, the UPS icon will appear on the screen. The Extra Battery icon will appear when Extra Battery is connected to the main model. The AC indicator icon will appear when the AC power button is turned on. The USB-A output icon will appear on the LCD display when a USB-A port is in use. The USB-C output icon will appear on the LCD display when a USB-C port is in use. The Car Power Output icon will appear on the LCD display when a Car Output port is in use. The icon will appear when the unit is connected to the App. Extra Battery Indicator AC Indicator USB-A Indicator USB-C Indicator IOT Indicator Car Power Output Indicator UPS Indicator j k l m n o p

USB-A Overload Protection USB-A and OVERLOAD icons flash together. Disconnect all electrical appliances and wait 10 seconds before adding each appliance back. The RIVER Pro display screen uses different icons and combined icons to indicate the reason for device protection. USB-C High Temperature Protection High Temperature Recharge-protection High Temperature Discharge-protection Low Temperature Recharging-protection Low Temperature Discharge-protection Overload Recharging-protection Overload Discharging-protection Communication Failure between Main Board and BMS USB-C and High-Temperature icons flash together. Let RIVER Pro cool before adding each appliance back. RECHARGING TIME, Exclamation and High-Temper- ture icons flash together. This will happen especially when you charge your device immediately after a heavy battery use. Disconnect all electrical applianc- es and wait until RIVER Pro has cooled down before connecting each appliance back. Exclamation and High-temperature icons flash together. The power supply can be resumed after the battery is cooled down. RECHARGING TIME, Exclamation and Low-Temperature icons flash together. Place RIVER Pro in warmer place before recharging. Exclamation and Overload icons flash together. Disconnect all appliances, restart RIVER Pro, and add each appliance back in turn. Please note that electrical appliances must be operated within rated power. Light stays on USB-C Overload Protection The USB-C icon and the OVERLOAD icon flash together. After unplugging the appliance, it will automatically resume operation after 10 seconds. Exclamation and Low-Temperature icons flash together. Place RIVER Pro in warmer place before turning Power back on. RECHARGING TIME, Exclamation and OVERLOAD icons flash together. Unplug Charging cables, restart RIVER Pro and plug back in. Only the Exclamation icon is flashing. Restart RIVER Pro. The Exclamation icon is on. Restart the device.

AC Inverter Output Overload Inverter High Temperature Protection Inverter Low Temperture Protection Fan Blockage Car Charger Overload Car Charger High Temparature Protection AC icon Flashes. Restart RIVER Pro. AC and Overload icons flash together. Wait 10 seconds, turn AC Power ON/OFF. If the icons keep flashing, do not charge or discharge the unit. Please note that electrical appliances must be operated within rated power. (For more information about X-Boost function, go to P10. AC and High-temperature icons flash together. Let the inverter cool down. Then turn AC Power On/ OFF . It will automatically resume operation. The AC and Low-Temperature icons flash together. Move RIVER Pro to a warmer place and wait for the inverter to warm up. Press AC Power ON/OFF button again. It will automatically recover. Fan icon flashes. Turn Off RIVER Pro and carefully clean and vacuum around vents on both ends . Turn System Power On. Car and OVERLOAD icons flash together. Restart RIVER Pro, and make sure that electrical appli- ances must be operated within rated power. Car and High-Temperature icons flash together. Wait for RIVER Pro to cool down and it will automat- ically recover. *If the product is not operating properly or the icon keep flashing, please contact the customer support team. Do not charge the unit.

How to recharge the RIVER Pro using solar panels? e.g.1 RIVER Pro Charging Port RIVER Pro Charging Port XT60 Connector XT60 Connector RIVER Pro SOLAR PANEL-21.6V X2 MC4 Connector SOLAR PANEL-21.6V Solar MC4 parallel connection cable * Users need to buy the solar panels and related parallel connection accessories on their own. RIVER Pro 1. Recommend Charging Method e.g.2(Only supports parallel connection, NOT serial connection) If you need to know more about the connection of solar panel, please refer to the Solar Panel User Guide. Here we focus on demonstrate how to connect RIVER Pro to 1 set of solar panel or connect RIVER Pro to 2 sets of solar panels in parallel. The RIVER Pro can support a 10-25V DC input. When the input exceeds 25V, the RIV- ER Pro's overvoltage protection will be triggered. Over voltage may damage the product. Users should follow these instructions. EcoFlow do not provide free repair services for any product damage caused by connecting many solar panels to the product or incorrect connection, even during the warranty period. Users can connect a solar panel (do not connect more than one in series) as shown in Example 1. Connect to MC4 to XT60 solar charge cable. Connect the XT60 connector to the RIVER Pro’s XT60 input to charge the device. Users can connect up to 2 sets of solar panels in parallel to the MC4 port as shown in Example 2. If you want to connect 2 sets of solar panels, connect them with our solar MC4 parallel connection cable. Connect the XT60 connector to the RIVER Pro’s XT60 input to charge the device. The parallel connection cable is an op- tional accessory that is sold separately.

SOLAR CABLE SOLAR PANEL - + + - RIVER Pro Entry-level UPS Use Reminder Entry-Level UPS User Guide Users can buy universal solar panels of MC4 connection standard on their own to power RIVER Pro, as long as the voltage and current (10-25V DC, 12A Max) comply with the specifications of RIVER Pro, the panels will be able to recharge RIVER Pro through the MC4 to XT60 conversion cable. However, EcoFlow do not provide free repair services for any damage to the product caused by the quality issue or improper operation of the third-party solar panels, even in the warranty period. Users can connect the AC charging cable of RIVER Pro to the power grid and connect a device to RIVER Pro and turn on the AC switch to automatically enter the entry-level UPS mode. When the grid power is cut off, power will be supplied from the battery of RIVER Pro to protect your device (as shown below). Entry-Level UPS Entry-level UPS function. RIVER Pro's X-Stream system supports an entry-level UPS function. You can use the RIVER Pro AC socket while the device is connected to a wall socket with AC power supply (the AC power comes from the grid, not the battery). When the grid loses power suddenly, the device can automatically switch to be powered by RIVER Pro in <30ms. This is an entry-level grade UPS function that does not support 0ms switch ing. Do not connect devices with high uninterrupted power supply requirements, Perform multiple tests to confirm compatibility before connecting devices such as data servers and workstations with RIVER Pro. EcoFlow will not be responsible for any loss of data or equipment damage caused by customers’ failure in following the instruc- tion. Since the UL2743 standard socket cannot be grounded effectively, please connect the grounded wire to the grounding screw port of the input end according to your own needs, to ensure the safety using of the electrical appliances. * UPS is only applicable to electrical appliances below 600W. Please do not use other equipment at the same time to avoid OVERLOAD. EcoFlow is not responsible for any abnormal operation or data loss caused by careless use. Only one RIVER Pro can conduct the UPS function; the UPS function is not available when more than one RIVER Pro is connected together. Please follow the connection instructions below:

X-Boost allows you to use 600W-1200W appliances with the 600W inverter without the disruption caused by overload protection. Traditional inverters will overload when one electrical appliance with a higher rated pow- er is connected. Those inverters cannot be used to power such appliances. X-Boost enables the powering of 600W-1200W electrical appliances. Please take note of the following when using this mode: 1. The X-Boost mode is enabled by default. You can use the EcoFlow app to turn this function on/off. Please do not connect the AC output to grid power when the X-Boost mode is on, doing so will activate the low-volt- age protection of the power station; 2. The X-Boost mode is not available in the following situations: the charging state and X-Boost mode off state. 3. When using appliances with a rated power of 600W-1200W, please connect only one appliance. When con- necting more than one electrical device, the change of voltage may affect the usage of other electrical devices.* * The X-Boost mode is not applicable for all electrical devices. Some devices with a rated power of 600W-1200W that have strict voltage requirements are still not compatible. Please conduct a full test to confirm before usage, It is recommended to use electrical equipment with heating elements and a rated pow- er between 600W-1200W, such as hair dryers and electric kettles.

RIVER Pro and RIVER Pro Extra Battery Con- nection Get the RIVER Pro , RIVER Pro Extra Battery and Expansion Power Cable ready. Then turn off the power of RIVER Pro and RIVER Pro Extra Battery. Follow the steps below. If the devices are not turned off, they cannot be suc- cessfully connected. 1. Open the soft cover below the AC port of RIVER Pro to expose the Expansion Power Port. Connect the Expan- sion Power Cable to the port. Tighten the screws on both sides of the port to secure the connection. 2. Open the dust cover of RIVER Pro Extra Battery to expose the Expansion Power Port. Connect the other end of the Expansion Power Cable to the port. Tighten the screws on both sides of the port to secure the connection. 3. Turn on the power button of RIVER Pro or RIVER Pro Extra Battery. If the display of RIVER Pro shows the Ex- tra Battery icon, the connection is successful. When connecting the devices for the first time, it is recommended to fully charge them first. Fully charge RIVER Pro and RIVER Pro Extra Battery and ensure that the voltage of both devices are consistent to maximize the performance of RIVER Pro Extra Battery. * Not included in the package, this cable only comes with RIVER Pro Extra Battery 1 2 3

AC Output (x3) / (x2 International Version) Full Sine Wave USB-A Output (x2) USB-A Fast Charge (x1) USB-C Output (x1) Car Power Output (x1) DC5521 Output (x2) Solar Charge Input Car Charger (Example 2) AC Charge Input Power (Example 1) AC Charge Input Voltage 100-120Vac (50Hz/60Hz) International Version 220-240Vac (50Hz/60Hz) 200W 10-25Vdc 12A Max 12Vdc 10A Max X-Stream Charge 660W Max 600W (Surge 1200W) total, 120Vac (50Hz/60Hz) / 230Vac (50Hz/60Hz) 5Vdc, 2.4A, 12W Max, per port 5Vdc, 9Vdc, 12Vdc, 2.4A, 28W Max 5Vdc, 9Vdc, 12Vdc, 15Vdc 20Vdc, 5A, 100W Max 136W, 13.6Vdc, 10A Max 13.6Vdc, 3A Max (per port) * 15.9 lbs (7.2kg) * 11.4 x 7.1 x 9.3 in (28.9 x 18.0 x 23.5 cm) 720Wh (28.8V) UL Standard, CE, FCC, RoHS Battery Cell Chemistry Discharge Temperature Charge Temperature Shelf Life Cycle Life Lithium-ion -4°F to 140°F (±5°F), -20°C to 60°C (±3°C) 32°F to 113°F (±5°F), 0 to 45°C (±3°C) 1 Year (after fully charged) 800 cycles to 80% capacity * Please Note: The above weight, size, etc. have certain measurement errors. Please refer to the actual measurement.

Example 1: Example 2: How to Recharge RIVER Pro <2 hrs <6.5 hrs 660W Max X-Stream charging Car Charger (120W Input) How do I recharge my RIVER Pro? Can RIVER Pro power my devices while it's charging? RIVER Pro has an AC charging port and an XT60 charging port located on the side of RIVER Pro. The RIV- ER Pro can be charged via AC power, 12V car charger or solar panels. Yes, RIVER Pro can output power while being charged. 0-80% charged in 1 hour 0-100% charged in 1.6 hour 0-100% charged less than 6.5 hours (AC charging cable included) (Car charge cable included)

How do I use RIVER Pro safely? Can it be upgraded? FAQs How do I clean for RIVER Pro? The RIVER Pro is a versatile tool on many adventures, so that simple cleaning will likely be required from time to time. Use dry, non-abrasive cloths to wipe. If you need to clean more thoroughly, we recommend that you use detergent that used for cleaning mobile phones and computer screens. Do Not expose RIVER Pro to lots of liquid. Please store RIVER Pro in a dry and cool place. DO NOT place it near water. If you need to store RIVER Pro for a long time, Please discharge RIVER Pro to 30%, then charge to 85% every 3 month, in order to extend battery life. Then turn off the main switch and store at room temperature. Please use RIVER Pro in its operating temperature range. Using RIVER Pro out of the optimal operating tem- perature range may cause RIVER Pro to exceed its safe and effective working limits. DO NOT immerse RIVER Pro in water. Doing so will void the warranty. RIVER Pro is not waterproofed. If RIVER Pro power electrical devices with heating-elements (600W) over half hours, it is normal to appear high-temperature protection. Please wait about 1 hour before charging, powering devices, or using the power station again. EcoFlow RIVER Pro User Manual and Warranty Card DC5521-DC5525 Cable AC Charging Cable (Input) Car Charge Cable (Input) Solar Charge Cable (MC4 to XT60 Input) What’s in the Box The firmware can be upgraded using the EcoFlow App. Turn on the RIVER Pro before firmware upgrade. It is recommended that the RIVER Pro is connected to an AC power source or has about 50% battery level when upgrading. Please do not use RIVER Pro to recharge your appliances and devices during firmware upgrade. For more details, please refer to “How to upgrade firmware” FAQ in APP.