Beckhoff CB7268 Original Manual

CB7268 3 Version: 1.1 Table of contents 1 Documentation issue status..................................................................................................................... 5 2 Notes on the documentation .................................................................................................................... 6 3 Safety instructions .................................................................................................................................... 7 4 Overview..................................................................................................................................................... 9 4.1 Properties .......................................................................................................................................... 9 4.2 List of features ................................................................................................................................. 10 4.3 Specifications and documents......................................................................................................... 11 5 External connections .............................................................................................................................. 12 5.1 External connector overview ........................................................................................................... 12 5.2 List of interfaces .............................................................................................................................. 12 5.3 Front panel: Power supply (X101) ................................................................................................... 13 5.4 Front panel: LAN 1 - 3 (X102, X103, X104)..................................................................................... 14 5.5 Front panel: DisplayPort (X105) ...................................................................................................... 15 5.6 Front panel: USB 3.1 GEN2 (X106-X109)....................................................................................... 16 6 Internal connections................................................................................................................................ 17 6.1 Internal connector overview............................................................................................................. 17 6.2 List of plugs ..................................................................................................................................... 17 6.3 Internal: BeaCon140........................................................................................................................ 18 6.4 Internal: Battery ............................................................................................................................... 21 6.5 Internal: FAN ................................................................................................................................... 21 6.6 Internal: M.2..................................................................................................................................... 22 7 LEDs.......................................................................................................................................................... 24 7.1 Power control................................................................................................................................... 24 7.2 SATA ............................................................................................................................................... 24 7.3 TwinCAT.......................................................................................................................................... 25 7.4 UPS-OCT......................................................................................................................................... 26 8 BIOS.......................................................................................................................................................... 27 8.1 Using the setup................................................................................................................................ 27 8.2 Main................................................................................................................................................. 28 8.3 Advanced......................................................................................................................................... 30 8.3.1 RC ACPI settings.............................................................................................................  31 8.3.2 CPU Configuration...........................................................................................................  32 8.3.3 Trusted Computing Disable .............................................................................................  33 8.3.4 Trusted Computing Enable..............................................................................................  34 8.3.5 ACPI Settings Enabled ....................................................................................................  35 8.3.6 ACPI Settings Disabled ...................................................................................................  35 8.3.7 Hardware Monitor ............................................................................................................  36 8.3.8 AMI Graphic Output Protocol Policy ................................................................................  36 8.3.9 PCI Subsystem Settings..................................................................................................  37 8.3.10 USB Configuration...........................................................................................................  39 8.3.11 NVMe Configuration ........................................................................................................  40 8.3.12 Power Controller Options.................................................................................................  41

CB7268 4 Version: 1.1 8.3.13 BAseCon* Configuration..................................................................................................  42 8.3.14 SATA And RST Configuration .........................................................................................  43 8.3.15 TLS Auth configuration ....................................................................................................  46 8.3.16 Network Stack Configuration ...........................................................................................  47 8.3.17 Network stack configuration enabled...............................................................................  48 8.3.18 Intel Rapid Storage Technology ......................................................................................  49 8.3.19 Intel Ethernet connection(2) I219-LM ..............................................................................  49 8.3.20 Driver Health....................................................................................................................  51 8.4 Chipset ............................................................................................................................................ 51 8.4.1 System Agent SA Configuration ......................................................................................  52 8.4.2 Graphics Configuration....................................................................................................  53 8.4.3 PCH-IO Configuration......................................................................................................  54 8.5 Security............................................................................................................................................ 60 8.5.1 Secure Boot.....................................................................................................................  61 8.6 Boot ................................................................................................................................................. 71 8.6.1 Advanced Fixed Boot Order Parameters.........................................................................  72 8.7 Save&Exit ........................................................................................................................................ 73 8.8 BIOS update .................................................................................................................................... 74 9 Mechanical drawings .............................................................................................................................. 75 9.1 PCB: Dimensions ............................................................................................................................ 75 9.2 PCB: Holes ...................................................................................................................................... 76 10 Technical data.......................................................................................................................................... 77 10.1 Electrical data .................................................................................................................................. 77 10.2 Environmental conditions ................................................................................................................ 77 10.3 Thermal specifications..................................................................................................................... 78 11 Support and Service................................................................................................................................ 79 12 Appendix I: Post Codes .......................................................................................................................... 80 13 Appendix II: Resources........................................................................................................................... 81 13.1 Interrupt CB7268 ............................................................................................................................. 81 13.2 PCI devices CB7268 ....................................................................................................................... 82 13.3 SMB devices CB7268...................................................................................................................... 83

CB7268 5 Version: 1.1 1 Documentation issue status  Version  Modifications  0.1  Preliminary version, mechanical part only  0.2  Preliminary version, BIOS entries added.  0.3  Preliminary version  1.0  Initial release, incl. change from BAseCon140 to BeaCon140  1.1  BIOS 0.14, updated and new cover page

CB7268 6 Version: 1.1 2 Notes on the documentation This description is only intended for the use of trained specialists in control and automation engineering who are familiar with the applicable national standards. It is essential that the documentation and the following notes and explanations are followed when installing and commissioning the components. It is the duty of the technical personnel to use the documentation published at the respective time of each installation and commissioning. The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards. Disclaimer The documentation has been prepared with care. The products described are, however, constantly under development. We reserve the right to revise and change the documentation at any time and without prior announcement. No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation. Trademarks Beckhoff®, TwinCAT®, EtherCAT®, EtherCAT G®, EtherCAT G10®, EtherCAT P®, Safety over EtherCAT®, TwinSAFE®, XFC®, XTS® and XPlanar® are registered and licensed trademarks of Beckhoff Automation GmbH. Other designations used in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owners. Patents The EtherCAT technology is patent protected, in particular by the following applications and patents: EP1590927, EP1789857, EP1456722, EP2137893, DE102015105702 with corresponding applications or registrations in various other countries. EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany Copyright © Beckhoff Automation GmbH & Co. KG, Germany. The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization are prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design.

Product-specific safety instructions can be found on following pages or in the areas mounting, wiring, commissioning etc. Exclusion of liability All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG. Personnel qualification This description is only intended for trained specialists in control, automation and drive technology who are familiar with the applicable national standards. Description of symbols In this documentation the following symbols are used with an accompanying safety instruction or note. The safety instructions must be read carefully and followed without fail! DANGER Serious risk of injury! Failure to follow the safety instructions associated with this symbol directly endangers the life and health of persons! WARNING Risk of injury! Failure to follow the safety instructions associated with this symbol endangers the life and health of per- sons! CAUTION Personal injuries! Failure to follow the safety instructions associated with this symbol can lead to injuries to persons! NOTE Damage to the environment or devices Failure to follow the instructions associated with this symbol can lead to damage to the environment or equipment. Tip or pointer This symbol indicates information that contributes to better understanding. UL note This symbol indicates important information regarding UL certification. Intended use The CB7268 Computer Board was designed and developed exclusively for configuration in automation processes. To that end the board is equipped with external interfaces in order to acquire or output digital or analog signals or forward them to higher-level components.

The specified limits for electrical and technical data must be adhered to.

art energy-saving DDR4 technology enables memory extension up to 16 GB. Standard interfaces include one DisplayPort connector in the front panel, 3 Gigabit LAN connectors and 4 USB3.1 GEN2 interfaces. The BeaCon140 connector allows flexible expansion of the CB7268's I/O functions. It provides 7 PCIe lanes, of which 4 can be multiplexed with SATA signals and 3 with USB 3.1 GEN2-signals. The configuration of the I/O functions is taken care of by the PIC on the expansion card. The PIC contains the configuration data, which are communicated to the board upon connection and thus enable an uncomplicated and self- configuring extension of the I/O options. An LED indicates the status of the power controller. The tiny CB7268 offers the full functionality of a motherboard. Power is supplied via a 4-pin connector on the front panel. Fig. 1: CB7268 block diagram

Availability of the processors The list of features lists all the processors that can be ordered. Their actual availability depends on the manufacturer.  List of features  CB7268  120 x 75 Board  CPU  Intel® Celeron® 4305U (DC, 2M, 2.0 GHz), TDP 15 W  Intel® Core™ i3-8145U (DC, 2M, 2.1 GHz), TDP 15 W  Intel® Core™ i5-8365U (QC, 6M, 1.6 GHz), TDP 15 W  Intel® Core™ i7-8665U (QC, 8M, 1.7 GHz), TDP 15 W  Socket  FCBGA1528  Memory  OnBoard DDR4-2400/LPDD3-2133  (depending on CPU up to 2400 MHz, up to 8 GB)  I/O on front panel  1 x power  1x DisplayPort(connection of an HDMI adapter for an  HDMI signal is possible.)  3 x LAN 10/100/1000  4 x USB 3.1 GEN2  Internal I/O  1x M.2 (B) socket, signals depend on chipset  (see Internal: M.2 [} 22]  1 x BeaCon140, signals (see Internal: BeaCon140 [} 18])  Graphic resolution  Max. resolution (HDMI 1.4) 4096x2304@24Hz  Max. resolution (DP1.2) 4096x2304@60Hz  Max. resolution (eDP - integrated flat screen)  4096x2304@60Hz  RTC  With external CMOS battery (via 2-pin connector  or expansion card)  BIOS  AMI® Aptio V  Power supply  24 VDC power supply unit (+20 % / - 15 %)  Overvoltage and undervoltage protection  Reverse polarity protection, UPS-OCT possible  Format  120 x 75 mm, electrically isolated

The following documents, specifications or webpages were used for the preparation of this manual or as further technical documentation respectively. • PCI Express® Base Specification • Version 2.0 • www.pcisig.com • ACPI specification • Version 3.0 • www.acpi.info • ATA/ATAPI specification • Version 7 Rev. 1 • www.t13.org • USB specifications • www.usb.org • SM-Bus specification • Version 2.0 • www.smbus.org • Intel® chip descriptions • Intel® WhiskeyLake product family data sheet, processors (Celeron4305UE, i3-8145UE, i5-8345UE, i7-8665UE) • www.intel.com • Intel® chip description • i210 datasheet • i219 data sheet • www.intel.com • American Megatrends® • Aptio™ Text Setup Environment (TSE) User Manual • www.ami.com • American Megatrends® • Aptio™ 5.x Status Codes • www.ami.com

The figure shows the external interfaces of the CB7268. The following list shows the interfaces with reference to the respective manual page, where further information about the respective interface can be found. Fig. 2: CB7268, external interfaces Front panel The illustration corresponds to the installation situation in the PC housing. 5.2 List of interfaces *number  Function (designation)  Page  P1300  Vin (X101)  See: Front panel: Power supply (X101) [} 13]  P900  LAN 1 (X102)  See: Front panel: LAN 1 - 3 (X102, X103, X104) [} 14]  P905  LAN 2 (X103)  See: Front panel: LAN 1 - 3 (X102, X103, X104) [} 14]  P902  LAN 2 (X104)  See: Front panel: LAN 1 - 3 (X102, X103, X104) [} 14]  P906  DisplayPort (X105)  See: Front panel: DisplayPort (X105) [} 15]  P901  USB3.1 (X106)  See: Front panel: USB 3.1 GEN2 (X106-X109) [} 16]  P903  USB3.1 (X107)  See: Front panel: USB 3.1 GEN2 (X106-X109) [} 16]  P904  USB3.1 (X108)  See: Front panel: USB 3.1 GEN2 (X106-X109) [} 16]  P907  USB3.1 (X109)  See:Front panel: USB 3.1 GEN2 (X106-X109) [} 16]  *Listing from right to left The numbers in brackets correspond to the external interfaces on the housing at the front of the In- dustrial PC.

Fig. 3: CB7268 Power X101 The connection for the power supply is implemented as a 2x2 pin housing connector (P20THR-1818504). The main power supply (24 V) for the module is on pin 3. This can also be implemented as UPS-OCT (One Cable Technology), i.e. the signal for the UPS is also transmitted to the board via this cable. Please note that there are system states in which the activation of a connected PC_Start switch is ignored by the system, e.g. during booting of a Windows operating system. In this case, repeat the operation of the switch after a few seconds. The same applies to connected PC_Start push buttons.  Pin assignment of the power plug:  Description  Signal Pin  Signal  Description  PC_On: Input for  starting and shutting down  the PC.  Low (0 V or open  contact): PC starts.  High (>3 V): PC shuts  down.  PC_On 1 3  Vin  24 V supply voltage  UPS-OCT is supported.  Power status: Output of the  Power Status. The voltage corresponds to the positive  supply voltage and  can be loaded  up to  500 mA.  Low (0 V): PC is off.  High (Vin): PC is on.  PC_ACTIVE 2 4  GND  Ground

The board has three Gigabit-LAN connections. (10BaseT, 100BaseT and 1000BaseT compatible network components can be connected to these. The required speed is selected automatically. Auto-Cross and Auto- Negotiate are available as well as PXE and RPL functionality. The controller is Intel®'s i219 for LAN1 and i210 for LAN 2 and LAN3. Fig. 4: CB7268 LAN X102-104  Pin assignment of LAN connector:  Pin  Name  Description  1  LAN-0  LAN line 0 +  2  LAN-0#  LAN line 0 -  3  LAN-1  LAN line 1 +  4  LAN-2  LAN line 2 +  5  LAN-2#  LAN line 2 -  6  LAN-1#  LAN line 1 -  7  LAN-3  LAN line 3 +  8  LAN-3#  LAN line 3 - The LEDs of the LAN interfaces indicate the activity and speed of the data transmission (Mbit/s). The left- hand LED lights up when there is a connection and activity, and the right-hand LED during data transmission:  Left LED  Permanent with connection,  Flashing during data transmis- sion  Right LED  Permanent during data trans- mission  Mbit/s  Green  Green  1000  Green  Orange  100  Green  None  10 Real-time applications The Ethernet port connected via PCIe is usually suitable for cycle times <= 1 ms and for distributed clock applications with EtherCAT. The Ethernet port integrated in the chipset is usually suitable for real-time Ethernet applications with cycle times > 1 ms (without distributed clocks).

For devices with a DisplayPort connection a corresponding standard connector (Foxconn 3VD11203- DPA1-4H) with one DisplayPort connection is available. The interface additionally provides HDMI/DVI signals that can be used with aid of an adapter. Please consult your distributor with regard to a suitable adapter. Fig. 5: CB7268 DP Out X105  Pin assignment of DisplayPort plug:  Description  Signal Pin  Signal  Description  Display Port Lane 0 +  L0 1 2  GND  Ground  Display Port Lane 0 -  L#0 3 4  L1  Display Port Lane 1 +  Ground  GND 5 6  L#1  Line 1 -  Display Port Lane 2 +  L2 7 8  GND  Ground  Display Port Lane 2 -  L#2 9 10  L3  Display Port Lane 3 +  Ground  GND 11 12  L#3  Display Port Lane 3 -  DP / HDMI  HDMI# 13 14  GND  Ground  Auxiliary plus  AUX 15 16  GND  Ground  Auxiliary minus  AUX# 17 18  HPD  Hot Plug Detect  Ground  GND 19 20  3.3 V  Supply voltage 3.3 V Switching to HDMI DisplayPort signals are led out via the interface by default. With the use of a level shifter cable the board switches the DisplayPort specification 1.1 automatically to HDMI signals.

The USB channels 1, 2, 3 and 4 are made available via a standard USB connector. These USB channels support the 3.1-GEN2 USB specification. In contrast to the specification, the USB 3.1 channels only supply current up to 500 mA. Devices with their own current supply must be used for higher power demands. The USB interfaces are electronically protected. All necessary settings for USB can be made in the BIOS. This applies to the USB interfaces. Note that the "USB mouse and keyboard" function in the BIOS setup is only required if the operating system does not offer USB support. This function should not be selected for settings in the setup and for booting Windows with a USB mouse and keyboard connected, because this would lead to considerable performance limitations. Fig. 6: CB7268 USB3.1 X106-109  Pin assignment USB3.1 Gen2 connector:  Pin  Signal  Description  1  VCC  5 V supply voltage  2  D-  Data - (USB 2.0)  3  D+  Data + (USB 2.0)  4  GND  Ground  5  RX-  Receive line - (USB 3.1)  6  RX+  Receive line + (USB 3.1)  7  GND  Ground  8  TX-  Transmit line - (USB 3.1)  9  TX+  Transmit line + (USB 3.1)

The figure shows the internal interfaces of the CB7268. The following list shows the internal connectors with reference to the respective manual page, where further information about the respective connector can be found. Fig. 7: CB7268 internal connector overview 6.2 List of plugs  Number  Function (designation)  Page  P1000  BeaCon140  See: Internal: BeaCon140 [} 18]  P401  Fan connector  Housing plug (four-pin)  See: Internal: FAN [} 21]  P400  RealTimeClock RTC-  Housing plug (two-pin)  See: Internal: Battery [} 21]  P1001  M.2 base (B)  See: Internal: M.2 [} 22]  *Listing from right to left

functions. It provides up to 7 PCIe lanes, of which a maximum of 4 can be multiplexed with SATA3.0 (6G) and a maximum of 4 with PCIe lines, as well as a maximum of 3 PCIe lines with a maximum of 3 USB3.1- GEN2 lines (see table). DisplayPort, SSIC, SMBus and 1-Wire signals can be fed out via the BeaCon140 connector. The extension board takes care of the configuration of the IO functions. A PIC on the expansion card contains the configuration data, which are communicated to the board upon connection and thus enable an uncomplicated and self-configuring extension of the I/O options. Observe the current limits! In order to avoid damaging the device, it is essential to observe the following current limits: A maximum load of 2.8 A per pin must not be exceeded. On account of the different current con- sumptions of the usable processors the actual current consumption may be lower. The respective maximum values can be obtained from your distributor on inquiry. Irrespective of the CPU in use, a maximum total load of 100 W must not be exceeded. NOTE Signal mirroring with BeaCon Stack Up connector With the Stack Up version of the BeaCon connector (connector at the top of the board), a stack is used for signal transfer to the mating connector. The signals are mirrored on this mating connector (Stack Down). There is no reflection on the stack. Fig. 8: CB7268-G2-BeaCon

 Description  Signal Pin  Signal  Description  P_VLoad 24 V  S UPS output  VOLOAD/  P_VOLOAD1 1 2  P_VIN1/VIN1  V_IN  S UPS input  P_VLoad 24 V  S UPS output  VOLOAD/  P_VOLOAD2 3 4  P_VIN2/VIN2  P_VIN  S UPS input  (not led out)  5V/NC 5 6  P_GND/GND  Ground  (not led out)  5V/NC 7 8  P_GND/GND  Ground INSULATION  Standby 5 Volt  S5V 13 14  S3.3 V  Standby 3.3 V  Ground  GND 15 16  GND  Ground  PCIe Lane 1 Transmit +  PE1/SATA4-TX 17 18  RX-SATA4/PE1  PCIe Lane 1 Receive +  PCIe Lane 1 Transmit -  PE1/SATA4-TX# 19 20  RX-SATA4/PE1#  PCIe Lane 1 Receive -  Ground  GND 21 22  GND  Ground  PCIe Clock Lane 1 +  PECLK1 23 24  PECLK2  PCIe Clock Lane 2 +  PCIe Clock Lane 1 -  PECLK1# 25 26  PECLK2#  PCIe Clock Lane 2 -  Ground  GND 27 28  GND  Ground  PCI Lane 2 Transmit +  PE2/SATA3-TX 29 30  RX-SATA3/PE2  PCIe Lane 2 Receive  PCI Lane 2 Transmit -  PE2/SATA3-TX# 31 32  RX-SATA3/PE2#  PCIe Lane 2 Receive -  Ground  GND 33 34  GND  Ground  PCIe Lane 3 Transmit +  PE3/SATA2-TX 35 36  RX-SATA2/PE3  PCIe Lane 3 Receive +  PCIe Lane 3 Transmit -  PE3/SATA2-TX# 37 38  RX-SATA2/PE3#  PCIe Lane 3 Receive -  Ground  GND 39 40  GND  Ground  PCIe Lane 3 Clock +  PECLK3 41 42  PECLK4  PCIe Clock 4 +  PCIe Lane 3 Clock 3 -  PECLK3# 43 44  PECLK4#  PCIe Clock 4 -  Ground  GND 45 46  GND  Ground  PCIe Lane 4 Transmit +  PE4/SATA1-TX 47 48  RX-SATA1/PE4  PCIe Lane 4 Receive +  PCIe Lane 4 Transmit -  PE4/SATA1-TX# 49 50  RX-SATA1/PE4#  PCIe Lane 4 Receive -  Ground  GND 51 52  GND  Ground  PCIe Clock  Enable Lane 1  active low  PCKE1/DEVSLP4# 53 54  DEVSLP3/PCKE2#  PCIe Lane 2 Clock  Enable active low  PCIe Clock  Enable Lane 3 -  PCKE3/DEVSLP2# 55 56  DEVSLP1/PCKE4#  PCIe Lane 4 Clock  Enable -  PCIe Reset active  low  PERST# 57 58  PEWAKE#  PCIe Wake active low  SMBus Clock  SMBCLK 59 60  SMBDAT  SMBus Data KEY  SMBus Alert active  low  SMB-Alert# 61 62  1Wire  1-Wire  PCIe Clock Enable  Lane 5  PCKE5/OC4# 63 64  OC3/PCKE6#  PCIe Lane 6 Clock  Enable 6 - KEY  PCIe Clock Enable  Lane 7  PCKE7/OC2# 65 66  OC1/PCKE8#  USB Overcurrent  active low  Ground  GND 67 68  GND  Ground  PCIe Lane 5 Transmit +  PE5/USB3-4/  USBC1-TX 69 70  RX-USBC1/  USB3-4/PE5  PCIe Lane 5 Receive +  PCIe Lane 5 Transmit -  PE5/USB3-4/  USBC1-TX# 71 72  RX-USBC1/  USB3-4/PE5#  PCIe Lane 5 Receive -

 Description  Signal Pin  Signal  Description  USB 2.0 Channel 7 +  USB2-4#/(GND) 73 74  USB2-3/(GND)  USB 2.0 channel 8  Data +  PCIe Clock Lane 5 +  PECLK5/  USBC-SBU1/  (GND) 75 76  PECLK6/(GND)  PCIe Lane 6 Clock +  PCIe Clock 5 -  PECLK5/  USBC-SBU2#/  (GND) 77 78  PECLK6#/(GND)  PCIe Clock Lane 6 -  USB 2.0 Channel 7 -  USB2-4#/(GND) 79 80  USB2-3 D#/(GND)  USB 2.0 channel 8  (not  led out)  PE6/USB3-3/  USBC2-TX 81 82  RX-USBC2/  USB3-3/PE6  (not  led out)  (not  led out)  PE6/USB3-3-TX/  USBC2-TX# 83 84  RX-USBC2/  USB3-3/PE6#  (not  led out)  Ground  GND 85 86  GND  Ground  PCIe Lane 7 Transmit +  PE7/USB3-2-TX 87 88  RX-USB3-2/PE7  PCIe Lane 7 Receive +  PCIe Lane 7 Transmit -  PE7/USB3-2-TX# 89 90  RX-USB3-2/PE7#  PCIe Lane 7 Receive -  USB 2.0 Channel 9 +  USB2-2 (GND) 91 92  USB2-1/(GND)  USB 2.0 Channel 10 +  PCIe Lane 8 Transmit +  PECLK7/(GND) 93 94  PECLK8/(GND)  PCIe Lane 8 Clock +  PCIe Lane 8 Transmit -  PECLK7#/(GND) 95 96  PECLK8#/(GND)  PCIe Clock Lane 8 -  USB 2.0 Channel 9 -  USB2-2#/(GND) 97 98  USB2-1#/(GND)  USB 2.0 Channel 10 -  PCIe Lane 8 Transmit +  PE8/USB3-1-TX 99 100  RX-USB3-1/PE8  PCIe Lane 8 Receive +  PCIe Lane 8 Transmit -  PE8/USB3-1-TX# 101 102  RX-USB3-1/PE8#  PCIe Lane 8 Receive -  Ground  GND 103 104  GND  Ground KEY  SATA GP1  SATAGP1 105 106  SATAGP2  SATA GP 2  (not  led out)  SATAGP3/  USBC-CC1 107 108  USB-CC2/  SATAGP4/  (not led out)  TwinCAT LED Red  TCLEDR 109 110  TCLEDG  TwinCAT LED Green  TwinCAT LED Blue  TCLEDB 111 112  RES  LAN-Sync  SATA LED active low  SATA-LED 113 114  USBPWREN  USB Power Enable  RTC Battery  BATT 115 116  PWRFAIL  SUSV  Power  Management  Event active low  PME# 117 118  PWRGOOD  Power good  Power button active low  PWRBTN# 119 120  MRST#  Reset button active low  PSON  PSON 121 122  ATXPWRGD  ATX Power good  Ground  GND 123 124  GND  Ground  DisplayPort -/  HDMID  DP#/DVI 125 126  DDCC/  DPAUX  DDC Clock /  DisplayPort Aux +  DisplayPort Hot  Plug Detect  DPHPD 127 128  DDCD/  DPAUX#  DDC Data /  DisplayPort Aux -  Ground  GND 129 130  GND  Ground  DisplayPort Lane 0 +  DPL0/TMDSD2 131 132  TMDSD1/DPL1  DisplayPort Lane 1+  DisplayPort Lane 0 -  DPL0/TMDSD2# 133 134  TMDSD1DPL1#  DisplayPort Lane 1 -  Ground  GND 135 136  GND  Ground  DisplayPort Lane 2+  DPL2/TMDS0 137 138  TMDSD3/DPL3  DisplayPort Lane 3 +  DisplayPort Lane 2 -  DPL2/FMDS0# 139 140  TMDSD3/DPL3#  DisplayPort Lane 3 -

the computer board. Fig. 9: CB7268-G2-Bat  Pin assignment: Battery connector  Pin  Signal  Description  1  3.3 V_RTC  3.3 V for RTC of the CPU  2  GND  Ground 6.5 Internal: FAN The computer board has a four-pin fan connector. This allows fans with 12 V supply voltage to be connected directly to the computer board. A signal for monitoring the fan speed is also available. Fig. 10: CB7268-G2-Fan  Pin assignment of fan connector:  Pin  Signal  Description  1  GND  Ground  2  12 V  Supply voltage 12 V regulated  3  TACHO  Speed monitoring  4  PWM  Speed control

can be inserted. Adapter cards with standard plug connectors are available as accessories. Please contact your distributor for this. Fig. 11: CB7268-M.2

 Description  Signal Pin  Signal  Description  Configuration pin  CONFIG_3 1 2  3.3 V1  Standby S3.3 Volt  Ground  GND 3 4  3.3 V2  Standby S3.3 Volt  Ground  GND 5 6  FCPWROFF#  Full Card Power OFF  active low  USB data +  USB D+ 7 8  WDISABLE#  (not led out)  USB data -  USB D- 9 10  GPIO9/DAS/  DDS/LED1  (not led out)  Ground  GND 11 12  Connector Key  Connector Key 13 14 15 16 17 18 19 20  GPIO5  (not led out)  Configuration pin  Config 0 21 22  GPIO6  (not led out)  (not led out)  GPIO11 23 24  GPIO7  (not led out)  (not led out)  DPR 25 26  GPIO10  (not led out)  Ground  GND 27 28  GPIO8  (not led out)  PCIe Lane 2 Receive -  PER1-USB3RX-  SSICRX# 29 30  UIM RST  (not led out)  PCIe Lane 2 Receive +  PER1-USB3RX-  SSICRX 31 32  UIM CLK  (not led out)  Ground  GND 33 34  UIM DATA  (not led out)  PCIe Lane 2 Transmit -  PET1-USB3TX-  SSICTX# 35 36  UIM PWR  (not led out)  PCIe Lane 2 Transmit +  PET1-USB3TX-  SSICTX 37 38  DEVSLP  DeviceSleep  Ground  GND 39 40  GPIO0  (not led out)  PCIe Lane 1 Receive +  PER0-SATAB 41 42  GPIO1  (not led out)  PCIe Lane 1 Receive -  PER0-SATAB# 43 44  GPIO2  (not led out)  Ground  GND 45 46  GPIO3  (not led out)  PCIe Lane 1 Transmit -  PET0-SATAA# 47 48  GPIO4  (not led out)  PCIe Lane 1 Transmit +  PET-SATAA 49 50  PRST#  PCIe Reset active low  Ground  GND 51 52  CLKREQ#  PCIe Clock Enable  active low  PCIe Lane 1  Reference Clock -  REFCLK# 53 54  PEWAKE#  Link Reactivation  active low  PCIe Lane 1  Reference Clock +  REFCLK 55 56  N/C  (not led out)  Ground  GND 57 58  N/C  (not led out)  (not led out)  ANTCTL0 59 60  COEX3  (not led out)  (not led out)  ANTCTL1 61 62  COEX2  (not led out)  (not led out)  ANTCTL2 63 64  COEX1  (not led out)  (not led out)  ANTCTL3 65 66  SIM DETECT  (not led out)  Power good  RESET# 67 68  SUSCLK  System clock  Configuration pin  CFG1 69 70  3.3 V  Standby S3.3 Volt  Ground  GND 71 72  3.3 V  Standby S3.3 Volt  Ground  GND 73 74  3.3 V  Standby S3.3 Volt  Configuration pin  CFG2 75

of colors and flashing intervals. Fig. 12: CB7268 Power LED  Color  Interval  Meaning  None  Steadily lit  System in error state  White  Steadily lit  Power fail  Cyan  Steadily lit  Reserved  Magenta  Steadily lit  S UPS active (if existent)  Blue  Steadily lit  Reserved  Yellow  Steadily lit  S5 state  Green  Steadily lit  S0 state  Red  Steadily lit  Reset/Start  Green/yellow  Flashing  Bootloader running without error  Red/yellow  Flashing  Bootloader is starting (start sequence is being run through)  Yellow  Flashing (6 s)  S4 state  Yellow  Flashing (3 s)  S3 state  Magenta  Flashing (0.5 s)  S UPS capacitance test (if S UPS exists)  Red/magenta  Flashing  Checksum error during I2C transmission in the boot loader A steadily lit red LED can indicate a hardware error. Adaptation of the status codes It is possible to adapt the status codes (e.g. as TwinCAT LED). To do this, the system colors can be changed with the aid of an SMB command. This change remains in force until the next restart or re- set. A change of the default colors is indicated by the additional flashing of the white LED. 7.2 SATA The RGB LED indicates the hard disk activity. Fig. 13: CB7268 SATA LED  Color  Interval  Meaning  Red  Flashing  Activity (access)

Fig. 14: CB7268 TC LED  Color  Interval  Meaning  Green  Steadily lit  TwinCAT Run Mode  Blue  Steadily lit  TwinCAT Config Mode  Red  Steadily lit  TwinCAT Stop

Fig. 15: CB7268 OCT LED  Color  Interval  Meaning  None  Steadily lit  No UPS-OCT connected  Blue  Flashing  Boot loader active  Yellow  Flashing  Moderate signal quality  Green  Flashing  Good signal quality  Red  Flashing  Poor signal quality If the LED is not lit, no UPS-OCT is connected. Adaptation of the status codes It is possible to adapt the status codes (e.g. as UPS-OCT-LED). To do this, the system colors can be changed with the aid of an SMB command. This change remains in force until the next restart or reset.

Within the individual setup pages the last saved settings can be restored can at any time with F2 (”Previous Values”). Use F3 (”Optimized Defaults”) to load the factory defaults. Use F2/F3 to load the complete set of settings and F4 to save them (”Save & Exit"). A “►” sign in front of the menu item indicates that a submenu is available. Use the arrow keys to navigate between menu items. Use the Enter key to select menu items and call submenus or selection dialogs. For each setup option a help text is displayed at the top right, which in many cases contains useful information about the option and permitted values, etc. Note on Setup Documentation The BIOS is regularly updated so that the available setup options can change at any time without notice. This may result in differences between the options actually available and those described below. It should also be noted that the settings shown in the setup menus below are not necessarily the recommended or default settings. Which settings must be selected depends on the application scenario in which the board is operated.

 None  Microcode revision  None  GT info  None  IGFX VBIOS version  None  IGFX GOP version  None  Memory RC version  None  Total Memory  None  Memory frequency  None  PCH information  Name  None  Stepping  None  ME FW version  None  System Date  Here you can change the system date.  System Time  Here you can change the system time.

Configurable TDP options mean that the computer manufacturer can change the base frequency and TDP of the CPU within the specific values published on the product specification page at https://Ark.Intel.com.

 Disabled / Enabled / Enabled (Emulate PwrBtn)  Show postcode on screen  Disabled / Enabled  RC ACPI settings  Submenu see: RC ACPI settings [} 31]  CPU Configuration  Submenu see: CPU Configuration [} 32]  Trusted Computing  Submenu see: Trusted Computing Disable [} 33]  Submenu see: Trusted Computing Enable [} 34]  ACPI Settings  Submenu see: ACPI Settings [} 35]  Hardware Monitor  Submenu see: Hardware Monitor [} 36]  AMI Graphic Output Protocol Policy  Submenu see: Graphic Output Protocol Policy [} 37]  PCI Subsystem Settings  Submenu see: PCI Subsystem Settings [} 37]  USB Configuration  Submenu see: USB Configuration [} 39]  NVMe Configuration  Submenu see: NVMe Configuration [} 40]  Power Controller Options  Submenu see: Power Controller Options [} 41]  BAseCon Configuration*  SATA And RST Configuration  Submenu see: SATA And RST Configuration [} 43]  Tls Auth configuration  Submenu see: TLS Auth configuration [} 46]  Network Stack Configuration  Submenu see: Network Stack Configuration [} 47]  Submenu see: Network stack configuration enabled [} 48]  Intel ® Rapid Storage Technology  Submenu see: Intel® Rapid Storage Technology [} 49]  Intel ® Ethernet connection(2) I219-  LM - 00:01:05:4E:97:84

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  RC ACPI Settings                                               │PTID Support will be loaded if  │ │                                                                 │enabled.                        │ │  PTID Support                         [Enabled]                 │                                │ │  PECI Access Method                   [Direct I/O]              │                                │ │                                                                 │                                │ │  MSI enabled                          [Enabled]                 │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  RC ACPI settings  PTID support  Enabled / Disabled  PECI access method  Direct I/O / ACPI  MSI enabled  Enabled / Disabled

 None  L1 instruction cache  None  L2 Cache  None  L3 Cache  None  L4 cache  None  VMX  None  SMX/TXT  None  Software Guard Extensions (SGX)  Disabled / Enabled / Software Controlled  Hardware prefetcher  Enabled / Disabled  Adjacent Cache Line Prefetch  Enabled / Disabled  Intel (VMX) Virtualization Technology  Enabled / Disabled  PECI  Enabled / Disabled  Active Processor Cores  All / 1 / 2 / 3  AES  Enabled / Disabled  Intel Trusted Execution Technology  None  Alias check request  None  DPR memory size (MB)  None  Reset AUX content  None

                 Aptio Setup Utility ─ Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Configuration                                                   │Enables or Disables BIOS        │ │ Security Device Support               [Disable]                 │support for security device.    │ │ NO Security Device Found                                        │O.S. will not show Security     │ │                                                                 │Device. TCG EFI protocol and    │ │                                                                 │INT1A interface will not be     │ │                                                                 │available.                      │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Configuration  Security device support  Disable / Enable  No security device found

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Configuration                                                  │Enables or Disables BIOS        │ │  Security Device Support              [Eanble]                  │support for security device.    │ │  Disable Block Sid                    [Disabled]                │O.S. will not show Security     │ │                                                                 │Device. TCG EFI protocol and    │ │  NO Security Device Found                                       │INT1A interface will not be     │ │                                                                 │available.                      │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └──────────────────────────────────────────────────────────────────────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Configuration  Security device support  Enable / Disable  Disable block Sid  Disabled / Enabled  No security device found NOTE Activating the Enable settings Use "Quit without saving" followed by "Yes" to perform a reset and activate the settings. Please note that not all CPUs support this function.

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  ACPI Settings                                                  │Enables or Disables BIOS ACPI   │ │                                                                 │Auto Configuration.             │ │  Enable ACPI Auto Configuration       [Enabled]                 │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  ACPI Settings  Enable ACPI Auto Configuration  Enabled / Disabled 8.3.6 ACPI Settings Disabled                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  ACPI Settings                                                  │Enables or Disables BIOS ACPI   │ │                                                                 │Auto Configuration.             │ │  Enable ACPI Auto Configuration       [Disabled]                │                                │ │                                                                 │                                │ │  Enable Hibernation                   [Disabled]                │                                │ │  Lock Legacy Resources                [Disabled]                │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←><: Select Screen             │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  ACPI Settings  Enable ACPI Auto Configuration  Disabled / Enabled  Enable hibernation  Enabled / Disabled  Lock legacy resources  Disabled / Enabled

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Intel(R) Graphics Controller                                   │Output Interface                │ │  Intel(R) GOP Driver [9.0.1105]                                 │                                │ │  Output Select                        [HDMI1]                   │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Intel® Graphics Controller  Intel® GOP Driver [9.0.1105]  Output select  DVI1

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  PCI Bus Driver Version               A5.01.17                  │Value to be programmed into     │ │                                                                 │PCI Latency Timer Register.     │ │  PCI Devices Common Settings:                                   │                                │ │  PCI Latency Timer                    [32 PCI Bus Clocks]       │                                │ │  PCI─X Latency Timer                  [64 PCI Bus Clocks]       │                                │ │  VGA Palette Snoop                    [Disabled]                │                                │ │  PERR# Generation                     [Disabled]                │                                │ │  SERR# Generation                     [Disabled]                │                                │ │  BME DMA Mitigation                   [Disabled]                │                                │ │                                                                 │                                │ │> PCI Hot─Plug Settings                                          │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry Options  PCI bus driver version  None  PCI device common settings:  PCI latency timer  32 / 64 / 96 / 128 / 160 /192 / 224 / 248 / PCI bus clock  PCI-X latency timer  32 / 64 / 96 / 128 / 160 /192 / 224 / 248 / PCI bus clock  VGA palette snoop  Disabled / Enabled  PERR# generation  Disabled / Enabled  SERR# generation  Disabled / Enabled  Above 4G Decoding  Disabled / Enabled  PCI Hot-Plug Settings  Submenu see: PCI Hot-Plug Settings [} 38]

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │                                                                 │If ENABLED allows BIOS build    │ │  PCI Hot─Plug Settings                                          │in Hot─Pug support. Use this    │ │                                                                 │feature if OS does not support  │ │  BIOS Hot─Plug Support                [Enabled]                 │PCI Express and SHPC hot─plug   │ │                                                                 │natively.                       │ │  PCI Buses Padding                    [1]                       │                                │ │  I/O Resources Padding                [4 K]                     │                                │ │  MMIO 32 bit Resources Padding        [16 M]                    │                                │ │  PFMMIO 32 bit Resources Padding      [16 M]                    │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  PCI Hot-Plug Settings  BIOS hot-plug support  Enabled / Disabled  PCI buses padding  Disabled / 1 / 2 / 3 / 4 / 5  I/O resources padding  Disabled / 4 K / 8 K / 16 K / 32 K  MMIO 32 bit resources padding  Disabled / 1 M / 2 M / 4 M / 8 M / 16 M / 32 M / 64 M / 128 M  PFMMIO 32 bit resources padding  Disabled / 1 M / 2 M / 4 M / 8 M / 16 M / 32 M / 64 M / 128 M

 None  USB Controllers:  1 XHCI  None  USB Devices:  1 keyboard  None  Legacy USB support  Enabled / Disabled / Auto  XHCI Hand-off  Enabled / Disabled  USB Mass Storage Driver Support  Enabled / Disabled  USB hardware delays and time-outs:  USB transfer time-out  1 / 5 / 10 / 20 sec  Device reset time-out  10 / 20 / 30 / 40 sec  Device power-up delay  Auto / Manual

 No NVME device found  None

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Bootloader Version                   1.01─37                   │Select Power line for external  │ │  Firmware Version                     1.02─28                   │USB devices, if powered─down    │ │  Mainboard Serial No                  ................          │                                │ │  Mainboard Prod. Date (Week.Year)     03.20                     │                                │ │  Mainboard BootCount                  11440                     │                                │ │  Mainboard Operation Time             56860min (948h)           │                                │ │  Voltage (Min/Max)                     5.00V / 5.10V            │                                │ │  Temperature (Min/Max)                ─40'C /108'C              │                                │ │                                                                 │                                │ │  ext. USB─Port Voltage                [Off in S3─5]             │                                │ │                                                                 │                                │ │  WatchDogTimer Mode                   [Normal Mode]             │                                │ │  WDT OSBoot timeout                   [Disabled]                ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │  OCT─Transmitter Revision             1.39                      │↑↓: Select Item                 │ │  No OCT─Receiver (or OCT─UPS) found                             │Enter: Select                   │ │  No OCT─UPS detected                                            │+/─: Change Opt.                │ │  USB disabled or USB─cable not connected                        │F1: General Help                │ │  UPS─ACPI─Device                      [Disabled]                │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Bootloader version  None  Firmware version  None  Mainboard serial no  None  Mainboard Prod. Date (Week.Year)  None  Mainboard BootCount  None  Mainboard operation time  None  Voltage /Min/Max)  None  Temperature (Min/Max)  None  ext. USB port voltage  Off in S3-5 / by SCVV  WatchDogTimer mode  Normal mode / Compatibility mode  WDT OSBoot Timeout  Disabled / 45 / 60 / ... / 255 seconds  OCT transmitter revision  None  No OCT receiver (or OCT_UPS) found  None  No OCT UPS detected  None  USB disabled or USB cable not  connected  None  UPS ACPI device  Disabled / Prefer OCT / Prefer USB / Use OCT / Use USB

                     revision  None  None  Block 6 disabled  None *Old name for BeaCon140.

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  SATA And RST Configuration                                     │Enable/Disable SATA Device.     │ │                                                                 │                                │ │  SATA Controller(s)                   [Enabled]                 │                                │ │  SATA Mode Selection                  [Intel RST Premium]       │                                │ │                                       With Intel Optane         │                                │ │                                       System Acceleration]      │                                │ │  SATA Interrupt Selection             [Msix]                    │                                │ │  SATA Test Mode                       [Disabled]                │                                │ │  RAID Device ID                       [Client]                  │                                │ │> Software Feature Mask Configuration                            │                                │ │  Aggressive LPM Support               [Disabled]                │                                │ │                                                                 │                                │ │  Serial ATA Port 0                    Empty                     │                                │ │    Software Preserve                  Unknown                   │                                │ │    Port 0                             [Enabled]                 │                                │ │    Hot Plug                           [Disabled]                │                                │ │    Configured as eSATA                Hot Plug supported        ├────────────────────────────────┤ │    External                           [Disabled]                │→←: Select Screen               │ │    Spin Up Device                     [Disabled]                │↑↓: Select Item                 │ │    SATA Device Type                   [Hard Disk Drive]         │Enter: Select                   │ │    SATA Port 0 DevSlp                 [Disabled]                │+/─: Change Opt.                │ │    DITO Configuration                 [Disabled]                │F1: General Help                │ │  Serial ATA Port 1                    Empty                     │F2: Previous Values             │ │    Software Preserve                  Unknown                   │F3: Optimized Defaults          │ │    Port 1                             [Enabled]                 │F4: Save & Reset                │ │    Hot Plug                           [Disabled]                │ESC: Exit                       │ │    Configured as eSATA                Hot Plug supported        │                                │ │    External                           [Disabled]                │                                │ │    Spin Up Device                     [Disabled]                │                                │ │    SATA Device Type                   [Hard Disk Drive]         │                                │ │    SATA Port 1 DevSlp                 [Disabled]                │                                │ │    DITO Configuration                 [Disabled]                │                                │ │  Serial ATA Port 2                    Empty                     │                                │ │    Software Preserve                  Unknown                   │                                │ │    Port 2                             [Enabled]                 │                                │ │    Hot Plug                           [Disabled]                │                                │ │    Configured as eSATA                Hot Plug supported        │                                │ │    External                           [Disabled]                │                                │ │    Spin Up Device                     [Disabled]                │                                │ │    SATA Device Type                   [Hard Disk Drive]         │                                │ │    SATA Port 2 DevSlp                 [Disabled]                │                                │ │    DITO Configuration                 [Disabled]                │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.

 SATA controller(s)  Enabled / Disabled  SATA mode selection  AHCI / Intel RST Premium With Intel Optane  System acceleration  SATA Test Mode  Disabled / Enabled  Software Feature Mask Configuration  Submenu see: Software Feature Mask Configuration [} 45]  Aggressive LPM support  Disabled / Enabled  Serial ATA port 0  None  Software Preserve  None  Port 0  Disabled / Enabled  Hot Plug  Disabled / Enabled  Configured as eSATA  None  External  Disabled / Enabled  spin-up device  Disabled / Enabled  SATA device type  HDD / SSD  SATA port 0 DevSlp  Disabled / Enabled  DITO configuration  Disabled / Enabled NOTE Serial ATA ports 0 - 2 The identical BIOS entries for ports 0 – 2 are listed as examples for port 0.

            Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Software Feature Mask Configuration                            │If enabled, indicates that the  │ │                                                                 │HDD password unlock in the OS   │ │  HDD Unlock                           [Enabled]                 │is enabled.                     │ │  LED Locate                           [Enabled]                 │                                │ │  RAID0                                [Enabled]                 │                                │ │  RAID1                                [Enabled]                 │                                │ │  RAID10                               [Enabled]                 │                                │ │  RAID5                                [Enabled]                 │                                │ │  Intel Rapid Recovery Technology      [Enabled]                 │                                │ │  OROM UI and BANNER                   [Enabled]                 │                                │ │  IRRT Only on eSATA                   [Enabled]                 │                                │ │  Smart Response Technology            [Enabled]                 │                                │ │  OROM UI Normal Delay                 [2secs]                   │                                │ │  RST Force Form                       [Disabled]                │                                │ │  System Acceleration with Intel(R)    [Enabled]                 │                                │ │  Optane (TM) Memory                                             │                                │ │  CPU Attached Storage                 [Enabled]                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Software Feature Mask Configuration  HDD Unlock  Enabled / Disabled  LED Locate  Enabled / Disabled  RAID0  Enabled / Disabled  RAID1  Enabled / Disabled  RAID10  Enabled / Disabled  RAID5  Enabled / Disabled  Intel Rapid Recovery Technology  Enabled / Disabled  OROM UI and BANNER  Enabled / Disabled  IRRT only on eSATA  Enabled / Disabled  Smart Response Technology  Enabled / Disabled  OROM UI normal delay  2 / 4 / 6 / 8 secs  RST Force Form  Disabled / Enabled  System acceleration with Intel®  Optane™ memory  Enabled / Disabled  CPU attached storage  Enabled / Disabled

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │                                                                 │Press  to configure      │ │> Server CA Configuration                                        │Server CA.                      │ │                                                                 │                                │ │> Client Cert Configuration                                      │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Server CA configuration  Submenu see: Server CA configuration [} 46]  Client cert configuration  None 8.3.15.1 Server CA configuration                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │                                                                 │Press  to enroll cert.   │ │> Enroll Cert                                                    │                                │ │> Delete Cert                                                    │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Enroll cert  Submenu see: Enroll cert  Delete cert  None

 None  Cert GUID  None  Commit changes and exit  None  Discard changes and exit  None 8.3.16 Network Stack Configuration                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Network Stack                        [Disabled]                │Enable/Disable UEFI Network     │ │                                                                 │Stack                           │ │                                                                 │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Network Stack  Disabled / Enabled NOTE Network stack enabled If network stack is enabled, additional menu items for displaying and setting the LAN controllers are shown here. To do this, carry out a reset.

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Network Stack                        [Enabled]                 │Enable/Disable UEFI Network     │ │  Ipv4 PXE Support                     [Enabled]                 │Stack                           │ │  Ipv4 HTTP Support                    [Disabled]                │                                │ │  Ipv6 PXE Support                     [Disabled]                │                                │ │  Ipv6 HTTP Support                    [Disabled]                │                                │ │  IPSEC Certificate                    [Enabled]                 │                                │ │  PXE boot wait time                   0                         │                                │ │  Media detect count                   1                         │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Network Stack  Disabled / Enabled  Ipv4 PXE Support  Disabled / Enabled  Ipv4 HTTP support  Disabled / Enabled  Ipv6 PXE Support  Disabled / Enabled  Ipv6 HTTP support  Disabled / Enabled  IPSEC certificate  Enabled / Disabled  PXE boot wait time  None  Media detect count  None NOTE PXE boot available PXE boot is available if you set network stack and Ipv4 PXE support to "Enable".

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Intel (R) RST 17.8.0.4414 RAID Driver                          │                                │ │                                                                 │                                │ │  No disks connected to system                                   │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Intel® RST 17.8.0.4414 RAID driver  No disks connected to system  None 8.3.19 Intel Ethernet connection(2) I219-LM                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.           Advanced ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  PORT CONFIGURATION MENU                                        │                                │ │> NIC Configuration                                              │Click to configure the network  │ │                                                                 │device port.                    │ │  Blink LEDs                           0                         │                                │ │  PORT CONFIGURATION INFORMATION                                 │                                │ │  UEFI Driver                          Intel(R) Gigabit 0.0.24   ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │  Adapter PBA                          FFFFFF─0FF                │↑↓: Select Item                 │ │  Chip Type                            Intel PCH SPT             │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │  PCI Device ID                        15B7                      │F1: General Help                │ │  PCI Address                          00:1F:06                  │F2: Previous Values             │ │  Link Status                          [Disconnected]            │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │  MAC Address                          00:01:05:4E:97:84         │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  Bios entry  Options  PORT CONFIGURATION MENU  NIC Configuration  See submenu: NIC Configuration [} 50]  Flashing LEDs  None  PORT CONFIGURATION INFORMATION  UEFI driver  None  PBA adapter  None  Chip type  None  PCI device ID  None  PCI address  None  Link status  None  MAC Address  None

 100 Mbps Half / 100 Mbps Full  Wake On LAN  Enabled / Disabled

 None 8.4 Chipset                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.     Main  Advanced  Chipset  Security  Boot  Save & Exit ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │> System Agent (SA) Configuration                                │System Agent (SA) Parameters    │ │> PCHIO Configuration                                            │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  System Agent (SA) Configuration  Submenu see: System Agent SA Configuration [} 52]  PCH-IO Configuration  Submenu see: PCH-IO Configuration [} 54]

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                     Chipset ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  System Agent (SA) Configuration                                │Graphics Configuration          │ │                                                                 │                                │ │  SA PCIe Code Version                 7.0.110.64                │                                │ │  VT─d                                 Supported                 │                                │ │                                                                 │                                │ │> Graphics Configuration                                         │                                │ │                                                                 │                                │ │  Stop Grant Configuration             [Auto]                    │                                │ │  VT─d                                 [Enabled]                 │                                │ │  CHAP Device (B0:D7:F0)               [Disabled]                ├────────────────────────────────┤ │  Thermal Device (B0:D4:F0)            [Enabled]                 │→←: Select Screen               │ │  GNA Device (B0:D8:F0)                [Enabled]                 │↑↓: Select Item                 │ │  CRID Support                         [Disabled]                │Enter: Select                   │ │  Above 4GB MMIO BIOS assignment       [Disabled]                │+/─: Change Opt.                │ │  X2APIC Opt Out                       [Disabled]                │F1: General Help                │ │  IPU Device (B0:D5:F0)                [Disabled]                │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  System Agent (SA) Configuration  SA PCIe code version  None  VT-d  None  Graphics Configuration  Submenu see: Graphics Configuration [} 53]  Stop grant configuration  Auto / Manual  VT-d  Enabled / Disabled  CHAP device (B0:07:F0)  Disabled / Enabled  Thermal device (B0:D4:F0)  Enabled / Disabled  GNA device (B0:D8:F0)  Enabled / Disabled  CRID support  Disabled / Enabled  Above 4GB MMIO BIOS assignment  Disabled / Enabled  X2APIC Opt Out  Disabled / Enabled  IPU device (B0:D5:F0)  Disabled / Enabled

BIOS CB7268 53 Version: 1.1 8.4.2 Graphics Configuration                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                     Chipset ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Graphics Configuration                                         │Graphics turbo IMON current     │ │                                                                 │values supported (14─31)        │ │  Graphics Turbo IMON Current          31                        │                                │ │  Skip Scaning of External Gfx Card    [Disabled]                │                                │ │                                                                 │                                │ │  Primary Display                      [Auto]                    │                                │ │  Select PCIE Card                     [Auto]                    │                                │ │> External Gfx Card Primary Display Configuration                │                                │ │  Internal Graphics                    [Auto]                    │                                │ │  GTT Size                             [8MB]                     │                                │ │  Aperture Size                        [256MB]                   │                                │ │  PSMI SUPPORT                         [Disabled]                │                                │ │  DVMT Pre─Allocated                   [32M]                     ├────────────────────────────────┤ │  DVMT Total Gfx Mem                   [256M]                    │→←: Select Screen               │ │  Intel Graphics Pei Display Peim      [Disabled]                │↑↓: Select Item                 │ │  VDD Enable                           [Enabled]                 │Enter: Select                   │ │  PM Support                           [Disabled]                │+/─: Change Opt.                │ │  PAVP Enable                          [Enabled]                 │F1: General Help                │ │  Cdynmax Clamping Enable              [Enabled]                 │F2: Previous Values             │ │  Cd Clock Frequency                   [675 Mhz]                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Graphics Configuration  Graphics turbo IMON current  None  Skip Scanning of External Gfx Card  Disabled / Enabled  Primary Display  Auto / IGFX / PCI / SG  Select PCIE Card  Auto / Elk Creek 4 / PEG Eval  External Gfx Card Primary Display  Configuration  None  Internal Graphics  Auto / Disabled / Enabled  GTT Size  2 / 4 / 8 MB  Aperture Size  128 / 256 / 512 / 1024 / 2048 MB  PSMI SUPPORT  Disabled / Enabled  DVMT Pre-Allocated  0M / 32M…60M  DVMT Total Gfx Mem  128M / 256M / MAX  Intel Graphics Pei Display Peim  Disabled / Enabled  VDD Enable  Enabled / Disabled  PM support  Disabled / Enabled  PAVP Enable  Enabled / Disabled  Cdynmax Clamping Enable  Enabled / Disabled  Cd Clock Frequency  337.5 / 450 / 540 / 675 Mhz

 Submenu see: PCI express configuration (Q370) [} 55]  USB Configuration  Submenu see: USB Configuration [} 59]  HD Audio Configuration  Submenu see: HD Audio Configuration [} 59]  PCH LAN controller  Enabled / Disabled  Wake on LAN Enable  Enabled / Disabled  Second LAN controller  Enabled / Disabled  Third LAN controller  Enabled / Disabled  M.2 slot 0  None  CLKRUN# logic  Enabled / Disabled  State after G3  S0 state / S5 state  Compatible revision ID  None  Legacy IO low latency  Enabled / Disabled  Enable TCO timer  Enabled / Disabled

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                     Chipset ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  PCI Express Configuration                                      │PCI Express Clock Gating        │ │                                                                 │Enable/Disable for each root    │ │  PCI Express Clock Gating             [Disabled]                │port.                           │ │  PCIE Port assigned to LAN            5                         │                                │ │  Peer Memory Write Enable             [Disabled]                │                                │ │  Compliance Test Mode                 [Disabled]                │                                │ │  PCIe─USB Glitch W/A                  [Disabled]                │                                │ │                                                                 │                                │ │  PCIe RP 1 (disabled on BAseCon)                                │                                │ │  PCIe RP 2 (disabled on BAseCon)                                │                                │ │  PCI Express Root Port 3              Lane configured as        │                                │ │                                       USB/SATA                  │                                │ │  PCI Express Root Port 4              Lane configured as        │                                │ │                                       USB/SATA                  │                                │ │  PCI Express Root Port 5              Lane configured as        │                                │ │                                       USB/SATA                  │                                │ │  PCI Express Root Port 6              Lane configured as        │                                │ │                                       USB/SATA                  ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │  PCIE Port 7 is assigned to LAN1                                │+/─: Change Opt.                │ │  PCIE Port 8 is assigned to LAN2                                │F1: General Help                │ │> PCIe Root Port 9 (to M.2─Slot0)                                │F2: Previous Values             │ │  PCIe Root Port 10 (to M.2─Slot0)                               │F3: Optimized Defaults          │ │  PCIe Root Port 11 (to BAseCon)                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │  PCIe Port 12 is assigned to LAN3                               │                                │ │  PCIe RP 13                           (disabled on BAseCon)     │                                │ │  PCIe RP 14                           (disabled on BAseCon)     │                                │ │  PCIe RP 15                           (disabled on BAseCon)     │                                │ │  PCIe RP 16                           (disabled on BAseCon)     │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.

 PCI express clock gating  Disabled / Enabled  PCIE port assigned to LAN  None  Peer memory write enable  Disabled / Enabled  Compliance test mode  Disabled / Enabled  PCIe USB glitch W/A  Disabled / Enabled  PCIe RP 1 (disabled on BAseCon)  Disabled / Enabled  PCIe RP 2 (disabled on BAseCon)  Disabled / Enabled  PCI express root port 3  None  PCI express root port 4  None  PCI express root port 5  None  PCI express root port 6  None  PCIe root port 7 is assigned to LAN1  None  PCIe root port 8 is assigned to LAN2  None  PCIe root port 9 (to M.2 slot0)  Enabled / Disabled  PCIe root port 10 (to M.2 slot0)  Enabled / Disabled  PCIe root port 11 (to BAseCon)  Enabled / Disabled  PCIe port 12 is assigned to LAN3  None  PCIe RP 13 (disabled on BAseCon)  Disabled / Enabled  PCIe RP14 (disabled on BAseCon)  Disabled / Enabled  PCIe RP 15 (disabled on BAseCon)  Disabled / Enabled  PCIe RP 16 (disabled on BAseCon)  Disabled / Enabled *Old name for BeaCon140.

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                     Chipset ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┘ │  PCI Express Root Port 9              [Enabled]                 │Control the PCI Express Root    │ │  Disable Gen2 Pll Shutdown and L1     [Disabled]                │Port.                           │ │  Controller Power gating                                        │                                │ │  Connection Type                      [Slot]                    │                                │ │  Gen3 Eq Phase3 Method                [Hardware]                │                                │ │  UPTP                                 5                         │                                │ │  DPTP                                 7                         │                                │ │  ACS                                  [Enabled]                 │                                │ │  PTM                                  [Enabled]                 │                                │ │  DPC                                  [Enabled]                 │                                │ │  EDPC                                 [Enabled]                 │                                │ │    URR                                [Disabled]                │                                │ │    FER                                [Disabled]                ├────────────────────────────────┤ │    NFER                               [Disabled]                │→←: Select Screen               │ │    CER                                [Disabled]                │↑↓: Select Item                 │ │    CTO                                [Disabled]                │Enter: Select                   │ │    SEFE                               [Disabled]                │+/─: Change Opt.                │ │    SENFE                              [Disabled]                │F1: General Help                │ │    SEC                                [Disabled]                │F2: Previous Values             │ │    PME SCI                            [Enabled]                 │F3: Optimized Defaults          │ │    Hot Plug                           [Disabled]                │F4: Save & Reset                │ │    Advanced Error Reporting           [Enabled]                 │ESC: Exit                       │ │  PCIe Speed                           [Auto]                    │                                │ │    Transmitter Half Swing             [Disabled]                │                                │ │  Detect Timeout                       0                         │                                │ │  Extra Bus Reserved                   0                         │                                │ │  Reserved Memory                      10                        │                                │ │  Reserved I/O                         0                         │                                │ │                                                                 │                                │ │  PCH PCIe LTR Congguration                                      │                                │ │  LTR                                  [Enabled]                 │                                │ │    Snoop Latency Override             [Auto]                    │                                │ │    Non Snoop Latency Override         [Auto]                    │                                │ │    Force LTR Override                 [Disabled]                │                                │ │                                                                 │                                │ │  LTR Lock                             [Disabled]                │                                │ │                                                                 │                                │ │ >Extra Options                                                  │                                │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  PCI express root port 9  Disabled / Enabled NOTE PCI Express Configuration The BIOS entries are shown here for port 9 as an example. For activation set the PCI Express root ports to “Enabled”.

 Disabled / Enabled  Prefetchable Memory  None  Reserved Memory Alignment  None  Prefetchable Memory Alignment  None

 Disabled / Enabled  USB port disable override  Disable link / Select per-pin 8.4.3.3 HD Audio Configuration                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                     Chipset ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  HD Audio Subsystem Configuration Settings                      │Control Detection of the        │ │                                                                 │HD─Audio device.                │ │  HD Audio                             [Enabled]                 │Disabled = HDA will be          │ │                                                                 │unconditionally disabled        │ │                                                                 │Enabled = HDA will be           │ │                                                                 │unconditionally enabled.        │ │                                                                 │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  HD audio subsystem configuration settings  HD audio  Enabled / Disabled

 User mode available  Enabled / Disabled  Secure Boot menu  Submenu see: Secure Boot [} 61]

 Not Active  Secure Boot Mode  Custom / Standard  Restore factory keys  Submenu see: Restore factory keys [} 62]  Reset To Setup Mode  Submenu see: Reset To Setup Mode [} 63]  Key Management  Submenu see: Key Management [} 64]

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  System Mode                          User                      │Force System to User Mode.      │ │                                                                 │Install factory default Secure  │ │  Secure Boot                          [Disabled]                │Boot key databases              │ │                                       Not Active                │                                │ │                                                                 │                                │ │  Secure Boot Mode                     [Custom]                  │                                │ │> Restore Factory Keys                                           │                                │ │> Reset To Setup Mode                                            │                                │ │                                                                 │                                │ │> Key Management            ┌─────── Install factory defaults ──────┐                             │ │                            │                                       │                             │ │                            │ Press 'Yes' to proceed 'No' to cancel │                             │ │                            │                                       │  ───────────────────────────│ │                            │───────────────────────────────────────│  elect Screen               │ │                            │       Yes                  No         │  elect Item                 │ │                            └───────────────────────────────────────┘  : Select                   │ │                                                                       Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  System Mode  None  Secure Boot  Disabled / Enabled  Not Active  Secure Boot Mode  Custom / Standard  Restore factory keys  Install factory defaults (see box)

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  System Mode                          User                      │Delete all Secure Boot key      │ │                                                                 │databases from NVRAM            │ │  Secure Boot                          [Disabled]                │                                │ │                                       Not Active                │                                │ │                                                                 │                                │ │  Secure Boot Mode                     [Custom]                  │                                │ │> Restore Factory Keys                                           │                                │ │> Reset To Setup Mode                                            │                                │ │                            ┌───────── Reset To Setup Mode ─────────┐                             │ │> Key Management            │                                       │                             │ │                            │ Deleting all variables will reset the │                             │ │                            │         System to Setup Mode          │                             │ │                            │        Do you want to proceed?        │  ───────────────────────────│ │                            │                                       │  elect Screen               │ │                            │───────────────────────────────────────│  elect Item                 │ │                            │       Yes                  No         │  : Select                   │ │                            └───────────────────────────────────────┘  Change Opt.                │ │                                                                       eneral Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  System Mode  none  Secure Boot  Disabled / Enabled  Not Active  Secure Boot Mode  Custom / Standard  Reset To Setup Mode  Reset To Setup Mode (see box)

 Disabled / Enabled  Restore factory keys  Submenu see: Restore factory keys [} 65]  Reset To Setup Mode  Submenu see: Reset To Setup Mode [} 65]  Export Secure Boot variables  Submenu see: Export Secure Boot Variables [} 66]  Enroll Efi Image  Submenu see: Enroll Efi Image [} 66]  Device guard ready  Remove 'UEFI CA' from DB  Submenu see: Remove UEFI CA from DB [} 67]  Restore DB defaults  Submenu see: Restore DB faults [} 67]  Secure Boot variables  Press enter key  PlatformKey(PK)  Press enter key  Key Exchange Keys  Press enter key  Authorized Signatures  Press enter key  Forbidden Signatures  Press enter key  Authorized TimeStamps  Press enter key  OsRecovery Signatures  Press enter key

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Force System to User Mode.      │ │                                                                 │Install factory default Secure  │ │  Factory Key Provision                [Disabled]                │Boot key databases              │ │> Restore Factory Keys                                           │                                │ │> Reset To Setup Mode                                            │                                │ │> Export Secure Boot variables                                   │                                │ │> Enroll Efi Image                                               │                                │ │                                                                 │                                │ │  Device Guard Ready                                             │                                │ │> Remove 'UEFI CA' from DB  ┌─────── Install factory defaults ──────┐                             │ │> Restore DB defaults       │                                       │                             │ │                            │ Press 'Yes' to proceed 'No' to cancel │                             │ │  Secure Boot variable │ Siz│                                       │  ───────────────────────────│ │> Platform Key(PK)     │  86│───────────────────────────────────────│  elect Screen               │ │> Key Exchange Keys    │ 156│       Yes                  No         │  elect Item                 │ │> Authorized Signatures│ 314└───────────────────────────────────────┘  : Select                   │ │> Forbidden  Signatures│ 3724│                                         Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Restore factory keys  see box 8.5.1.3.2 Reset To Setup Mode                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Delete all Secure Boot key      │ │                                                                 │databases from NVRAM            │ │  Factory Key Provision                [Disabled]                │                                │ │> Restore Factory Keys                                           │                                │ │> Reset To Setup Mode                                            │                                │ │> Export Secure Boot variables                                   │                                │ │> Enroll Efi Image                                               │                                │ │                                                                 │                                │ │  Device Guard Ready        ┌───────── Reset To Setup Mode ─────────┐                             │ │> Remove 'UEFI CA' from DB  │                                       │                             │ │> Restore DB defaults       │ Deleting all variables will reset the │                             │ │                            │         System to Setup Mode          │                             │ │  Secure Boot variable │ Siz│        Do you want to proceed?        │  ───────────────────────────│ │> Platform Key(PK)     │  86│                                       │  elect Screen               │ │> Key Exchange Keys    │ 156│───────────────────────────────────────│  elect Item                 │ │> Authorized Signatures│ 314│       Yes                  No         │  : Select                   │ │> Forbidden  Signatures│ 372└───────────────────────────────────────┘  Change Opt.                │ │> Authorized TimeStamps│    0│                                         eneral Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Restore To Setup Mode  see box

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Copy NVRAM content of Secure    │ │                                                                 │Boot variables to files in a    │ │  Factory Key Provision                [Disabled]                │root folder on a file system    │ │> Restore Factory Keys                                           │device                          │ │> Reset To Setup Mode                                            │                                │ │> Export Secure Boot variables                                   │                                │ │> Enroll Efi Image                                               │                                │ │                                                                 │                                │ │  Device Guard Ready                                             │                                │ │> Remove 'UEFI CA' from DB      ┌───────── File System ──────────┐                                │ │> Restore DB defaults           │                                │                                │ │                                │ No Valid File System Available │                                │ │  Secure Boot variable │ Size│ K│                                │  ──────────────────────────────│ │> Platform Key(PK)     │  862│  │────────────────────────────────│  : Select Screen               │ │> Key Exchange Keys    │ 1560│  │               Ok               │  : Select Item                 │ │> Authorized Signatures│ 3143│  └────────────────────────────────┘  ter: Select                   │ │> Forbidden  Signatures│ 3724│   7                                  ─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Export Secure Boot Variables  File system, see box 8.5.1.3.4 Enroll Efi Image                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Copy NVRAM content of Secure    │ │                                                                 │Boot variables to files in a    │ │  Factory Key Provision                [Disabled]                │root folder on a file system    │ │> Restore Factory Keys                                           │device                          │ │> Reset To Setup Mode                                            │                                │ │> Export Secure Boot variables                                   │                                │ │> Enroll Efi Image                                               │                                │ │                                                                 │                                │ │  Device Guard Ready                                             │                                │ │> Remove 'UEFI CA' from DB      ┌───────── File System ──────────┐                                │ │> Restore DB defaults           │                                │                                │ │                                │ No Valid File System Available │                                │ │  Secure Boot variable │ Size│ K│                                │  ──────────────────────────────│ │> Platform Key(PK)     │  862│  │────────────────────────────────│  : Select Screen               │ │> Key Exchange Keys    │ 1560│  │               Ok               │  : Select Item                 │ │> Authorized Signatures│ 3143│  └────────────────────────────────┘  ter: Select                   │ │> Forbidden  Signatures│ 3724│   7                                  ─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Enroll Efi Image  see box

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Device Guard ready system must  │ │                                                                 │not list 'Microsoft UEFI CA'    │ │  Factory Key Provision                [Disabled]                │Certificate in Authorized       │ │> Restore Factory Keys                                           │Signature database (db)         │ │> Reset To Setup Mode                                            │                                │ │> Export Secure Boot variables                                   │                                │ │> Enroll Efi Image                                               │                                │ │                                                                 │                                │ │  Device Guard Ready                                             │                                │ │> Remove 'UEFI CA' from DB  ┌─────── Remove 'UEFI CA' from DB ──────┐                             │ │> Restore DB defaults       │                                       │                             │ │                            │ Press 'Yes' to proceed 'No' to cancel │                             │ │  Secure Boot variable │ Siz│                                       │  ───────────────────────────│ │> Platform Key(PK)     │  86│───────────────────────────────────────│  elect Screen               │ │> Key Exchange Keys    │ 156│       Yes                  No         │  elect Item                 │ │> Authorized Signatures│ 314└───────────────────────────────────────┘  : Select                   │ │> Forbidden  Signatures│ 3724│                                         Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Remove ‘UEFI CA’ from DB  see box 8.5.1.3.6 Restore DB faults                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Restore DB variable to factory  │ │                                                                 │defaults                        │ │  Factory Key Provision                [Disabled]                │                                │ │> Restore Factory Keys                                           │                                │ │> Reset To Setup Mode                                            │                                │ │> Export Secure Boot variables                                   │                                │ │> Enroll Efi Image                                               │                                │ │                                                                 │                                │ │  Device Guard Ready                                             │                                │ │> Remove 'UEFI CA' from DB  ┌───────── Restore DB defaults ─────────┐                             │ │> Restore DB defaults       │                                       │                             │ │                            │ Press 'Yes' to proceed 'No' to cancel │                             │ │  Secure Boot variable │ Siz│                                       │  ───────────────────────────│ │> Platform Key(PK)     │  86│───────────────────────────────────────│  elect Screen               │ │> Key Exchange Keys    │ 156│       Yes                  No         │  elect Item                 │ │> Authorized Signatures│ 314└───────────────────────────────────────┘  : Select                   │ │> Forbidden  Signatures│ 3724│                                         Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Restore DB faults  see box

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Enroll Factory Defaults or      │ │                                                                 │load certificates from a file:  │ │  Factory Key Provision                [Disabled]                │ 1.Public Key Certificate:      │ │> Restore Factory Keys                                           │  a)EFI_SIGNATURE_LIST          │ │> Reset To Setup Mode                                            │  b)EFI_CERT_X509 (DER)         │ │> Export Secure Boot variables                                   │  c)EFI_CERT_RSA2048 (bin)      │ │> Enroll Efi Image                                               │  d)EFI_CERT_SHAXXX             │ │                                 ┌──────────────────────────────┐│ 2.Authenticated UEFI Variable  │ │  Device Guard Ready             │    Platform Key(PK)          ││ 3.EFI PE/COFF Image(SHA256)    │ │> Remove 'UEFI CA' from DB       │──────────────────────────────││Key Source:                     │ │> Restore DB defaults            │ Details                      ││ Factory,External,Mixed         │ │                                 │ Export                       ││                                │ │  Secure Boot variable │ Size│ Ke│ Update                       ││────────────────────────────────│ │> Platform Key(PK)     │  862│   │ Delete                       ││→←: Select Screen               │ │> Key Exchange Keys    │ 1560│   └──────────────────────────────┘│↑↓: Select Item                 │ │> Authorized Signatures│ 3143│    2│ Factory                     │Enter: Select                   │ │> Forbidden  Signatures│ 3724│   77│ Factory                     │+/─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Platform Key (PK)  see box 8.5.1.3.8 Key Exchange Keys                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Enroll Factory Defaults or      │ │                                                                 │load certificates from a file:  │ │  Factory Key Provision                [Disabled]                │ 1.Public Key Certificate:      │ │> Restore Factory Keys                                           │  a)EFI_SIGNATURE_LIST          │ │> Reset To Setup Mode                                            │  b)EFI_CERT_X509 (DER)         │ │> Export Secure Boot variables                                   │  c)EFI_CERT_RSA2048 (bin)      │ │> Enroll Efi Image                                               │  d)EFI_CERT_SHAXXX             │ │                                 ┌──────────────────────────────┐│ 2.Authenticated UEFI Variable  │ │  Device Guard Ready             │    Key Exchange Keys         ││ 3.EFI PE/COFF Image(SHA256)    │ │> Remove 'UEFI CA' from DB       │──────────────────────────────││Key Source:                     │ │> Restore DB defaults            │ Details                      ││ Factory,External,Mixed         │ │                                 │ Export                       ││                                │ │  Secure Boot variable │ Size│ Ke│ Update                       ││────────────────────────────────│ │> Platform Key(PK)     │  862│   │ Append                       ││→←: Select Screen               │ │> Key Exchange Keys    │ 1560│   │ Delete                       ││↑↓: Select Item                 │ │> Authorized Signatures│ 3143│   └──────────────────────────────┘│Enter: Select                   │ │> Forbidden  Signatures│ 3724│   77│ Factory                     │+/─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Key  Exchange Keys  see box

BIOS CB7268 69 Version: 1.1 8.5.1.3.9 Authorized Signatures                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Enroll Factory Defaults or      │ │                                                                 │load certificates from a file:  │ │  Factory Key Provision                [Disabled]                │ 1.Public Key Certificate:      │ │> Restore Factory Keys                                           │  a)EFI_SIGNATURE_LIST          │ │> Reset To Setup Mode                                            │  b)EFI_CERT_X509 (DER)         │ │> Export Secure Boot variables                                   │  c)EFI_CERT_RSA2048 (bin)      │ │> Enroll Efi Image                                               │  d)EFI_CERT_SHAXXX             │ │                                 ┌──────────────────────────────┐│ 2.Authenticated UEFI Variable  │ │  Device Guard Ready             │    Authorized Signatures     ││ 3.EFI PE/COFF Image(SHA256)    │ │> Remove 'UEFI CA' from DB       │──────────────────────────────││Key Source:                     │ │> Restore DB defaults            │ Details                      ││ Factory,External,Mixed         │ │                                 │ Export                       ││                                │ │  Secure Boot variable │ Size│ Ke│ Update                       ││────────────────────────────────│ │> Platform Key(PK)     │  862│   │ Append                       ││→←: Select Screen               │ │> Key Exchange Keys    │ 1560│   │ Delete                       ││↑↓: Select Item                 │ │> Authorized Signatures│ 3143│   └──────────────────────────────┘│Enter: Select                   │ │> Forbidden  Signatures│ 3724│   77│ Factory                     │+/─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Authorized Signatures  see box 8.5.1.3.10 Forbidden Signatures                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Enroll Factory Defaults or      │ │                                                                 │load certificates from a file:  │ │  Factory Key Provision                [Disabled]                │ 1.Public Key Certificate:      │ │> Restore Factory Keys                                           │  a)EFI_SIGNATURE_LIST          │ │> Reset To Setup Mode                                            │  b)EFI_CERT_X509 (DER)         │ │> Export Secure Boot variables                                   │  c)EFI_CERT_RSA2048 (bin)      │ │> Enroll Efi Image                                               │  d)EFI_CERT_SHAXXX             │ │                                 ┌──────────────────────────────┐│ 2.Authenticated UEFI Variable  │ │  Device Guard Ready             │    Forbidden  Signatures     ││ 3.EFI PE/COFF Image(SHA256)    │ │> Remove 'UEFI CA' from DB       │──────────────────────────────││Key Source:                     │ │> Restore DB defaults            │ Details                      ││ Factory,External,Mixed         │ │                                 │ Export                       ││                                │ │  Secure Boot variable │ Size│ Ke│ Update                       ││────────────────────────────────│ │> Platform Key(PK)     │  862│   │ Append                       ││→←: Select Screen               │ │> Key Exchange Keys    │ 1560│   │ Delete                       ││↑↓: Select Item                 │ │> Authorized Signatures│ 3143│   └──────────────────────────────┘│Enter: Select                   │ │> Forbidden  Signatures│ 3724│   77│ Factory                     │+/─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  Bios entry  Options  Vendor Keys  None  Forbidden Signatures  see box

BIOS CB7268 70 Version: 1.1 8.5.1.3.11 Authorized TimeStamps                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Enroll Factory Defaults or      │ │                                                                 │load certificates from a file:  │ │  Factory Key Provision                [Disabled]                │ 1.Public Key Certificate:      │ │> Restore Factory Keys                                           │  a)EFI_SIGNATURE_LIST          │ │> Reset To Setup Mode                                            │  b)EFI_CERT_X509 (DER)         │ │> Export Secure Boot variables                                   │  c)EFI_CERT_RSA2048 (bin)      │ │> Enroll Efi Image                                               │  d)EFI_CERT_SHAXXX             │ │                                                                 │ 2.Authenticated UEFI Variable  │ │  Device Guard Ready             ┌──────────────────────────────┐│ 3.EFI PE/COFF Image(SHA256)    │ │> Remove 'UEFI CA' from DB       │    Authorized TimeStamps     ││Key Source:                     │ │> Restore DB defaults            │──────────────────────────────││ Factory,External,Mixed         │ │                                 │ Update                       ││                                │ │  Secure Boot variable │ Size│ Ke│ Append                       ││────────────────────────────────│ │> Platform Key(PK)     │  862│   └──────────────────────────────┘│→←: Select Screen               │ │> Key Exchange Keys    │ 1560│    1│ Factory                     │↑↓: Select Item                 │ │> Authorized Signatures│ 3143│    2│ Factory                     │Enter: Select                   │ │> Forbidden  Signatures│ 3724│   77│ Factory                     │+/─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  Authorized TimeStamps  see box 8.5.1.3.12 OsRecovery Signatures                  Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                              Security ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Vendor Keys                          Modified                  │Enroll Factory Defaults or      │ │                                                                 │load certificates from a file:  │ │  Factory Key Provision                [Disabled]                │ 1.Public Key Certificate:      │ │> Restore Factory Keys                                           │  a)EFI_SIGNATURE_LIST          │ │> Reset To Setup Mode                                            │  b)EFI_CERT_X509 (DER)         │ │> Export Secure Boot variables                                   │  c)EFI_CERT_RSA2048 (bin)      │ │> Enroll Efi Image                                               │  d)EFI_CERT_SHAXXX             │ │                                                                 │ 2.Authenticated UEFI Variable  │ │  Device Guard Ready             ┌──────────────────────────────┐│ 3.EFI PE/COFF Image(SHA256)    │ │> Remove 'UEFI CA' from DB       │    OsRecovery Signatures     ││Key Source:                     │ │> Restore DB defaults            │──────────────────────────────││ Factory,External,Mixed         │ │                                 │ Update                       ││                                │ │  Secure Boot variable │ Size│ Ke│ Append                       ││────────────────────────────────│ │> Platform Key(PK)     │  862│   └──────────────────────────────┘│→←: Select Screen               │ │> Key Exchange Keys    │ 1560│    1│ Factory                     │↑↓: Select Item                 │ │> Authorized Signatures│ 3143│    2│ Factory                     │Enter: Select                   │ │> Forbidden  Signatures│ 3724│   77│ Factory                     │+/─: Change Opt.                │ │> Authorized TimeStamps│    0│    0│ No Keys                     │F1: General Help                │ │> OsRecovery Signatures│    0│    0│ No Keys                     │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Vendor Keys  None  OsRecovery Signatures  see box

 None  Bootup NumLok state  On / Off  F7 Boot Menu  Enabled / Disabled  Quiet Boot  Enabled / Disabled  Fast boot  Disable Link / Enabled  Boot mode select  None  Fixed Boot Order Priorities  Boot Option #1- #11  Here you can set the order of the boot media to be used.  Advanced Fixed Boot Order  Parameters  Submenu see: Advanced Fixed Boot Order Parameters [} 72]

                 Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.                                        Boot ┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │  Min. CFast capacity (GB)             0                         │Lower capacity limit for boot   │ │  Max. CFast capacity (GB)             119                       │group CFast in GB               │ │  Min. SSD capacity (GB)               119                       │                                │ │  Max. SSD capacity (GB)               481                       │                                │ │  Min. HDD capacity (GB)               481                       │                                │ │  Max. HDD capacity (GB)               8000000                   │                                │ │  Max. USB Stick capacity (GB)         64                        │                                │ │                                                                 │                                │ │  UEFI BDS Boot Filter                 [Enabled]                 │                                │ │  Re─enable UEFI Disks                 [Enabled]                 │                                │ │                                                                 ├────────────────────────────────┤ │                                                                 │→←: Select Screen               │ │                                                                 │↑↓: Select Item                 │ │                                                                 │Enter: Select                   │ │                                                                 │+/─: Change Opt.                │ │                                                                 │F1: General Help                │ │                                                                 │F2: Previous Values             │ │                                                                 │F3: Optimized Defaults          │ │                                                                 │F4: Save & Reset                │ │                                                                 │ESC: Exit                       │ │                                                                 │                                │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘                   Version 2.20.1275. Copyright (C) 2020 American Megatrends, Inc.  BIOS entry  Options  Min. CFast capacity (GB)  None  Max. CFast capacity (GB)  None  Min. SSD capacity (GB)  None  Max. SSD capacity (GB)  None  Min. HDD capacity (GB)  None  Max. HDD capacity (GB)  None  Max. USB Stick capacity (GB)  None  UEFI BDS Boot filter  Enabled / Disabled  Re-enable UEFI disks  Enabled / Disabled

 Discard Changes and Reset  Press enter key  Restore defaults  Press enter key  Boot Override  Launch EFI Shell from filesystem device  None

be updated. When doing this it is important to start the program from a DOS environment without a virtual memory manager such as "EMM386.EXE". If such a memory manager is loaded, the program will abort with an error message or cause a crash. DecdFlsh is a program for the automatic updating of the BIOS on all boards with AMI-BIOS. All files contained in the zip file must be unpacked into a directory, from where DecdFlsh Bios-Dateiname calling takes place. The name of the BIOS file and its length are checked. The BIOS will now be programmed. DecdFlsh also exists as a UEFI tool for calling from the UEFI shell. A running Flash procedure must never be interrupted, as otherwise the BIOS on the board will be destroyed. The Flash procedure takes about 75 seconds. The necessary firmware update takes place automatically. Avoid damage due to incorrect update execution! If the BIOS update is performed incorrectly, the board may become unusable. Therefore a BIOS up- date should only be done if the corrections / additions that the new BIOS version brings with it are really needed. Before a planned BIOS update, it is essential to ensure that the BIOS file to be reloaded is really re- leased for exactly this board and for exactly this board version. If an inappropriate file is used, the board will inevitably not boot afterwards.

9.1 PCB: Dimensions Fig. 16: CB7268 circuit board dimensions

 Power  transformer  45 W continuous load  70 W peak load  Current consumption  RTC  ≤ 10 µA 10.2 Environmental conditions  Temperature range  Operating  0 °C to +60 °C (extended temperature range  on request)  Storage  -25 °C to +85 °C  Dispatch  -25 °C to +85 °C, for packed boards  Temperature changes  Operating  0.5 °C per minute, 7.5 °C in 30 minutes  Storage  1.0 °C per minute  Dispatch  1.0 °C per minute, for packed boards  Relative humidity  Operating  5% to 85% (non-condensing)  Storage  5% to 95% (non-condensing)  Dispatch  5% to 100% (non-condensing), for packed  boards  Impact  Operating  150 m/s², 6 ms  Storage  400 m/s², 6 ms  Dispatch  400 m/s², 6 ms, for packed boards  Vibrations  Operating  10 to 58 Hz, amplitude 0.075 mm  58 to 500 Hz, 10 m/s²  Storage  5 to 9 Hz, amplitude 3.5 mm  9 to 500 Hz, 10 m/s²  Dispatch  5 to 9 Hz, 3.5 mm amplitude  9 to 500 Hz, 10 m/s², for packed boards Note on impact and vibration resistance The specifications for impact and vibration resistance refer only to the motherboard itself without heat sink, memory module, cabling, etc.

request). In addition, care must be taken that the temperature of the processor die does not exceed 110 °C. To ensure this a suitable cooling concept must be implemented that is oriented to the maximum power consumption of the processor/chipset. It must also be ensured that any existing controllers are included in the cooling concept. The power consumption of these function blocks may be of the same order of magnitude as the power consumption of the processor. The board is prepared with suitable holes for the use of modern cooling solutions. We have a series of compatible cooling components in our range. Your distributor will be pleased to assist you in selecting suitable solutions. NOTE Prevent the maximum die temperature being exceeded! It is the end customer's responsibility to ensure that the die temperature of the processor does not exceed 110 °C! Continuous overheating can destroy the board! If the temperature exceeds 110 °C, the ambient temperature needs to be reduced. Ensure sufficient air cir- culation if necessary.

CB7268 79 Version: 1.1 11 Support and Service Beckhoff and their partners around the world offer comprehensive support and service, making available fast and competent assistance with all questions related to Beckhoff products and system solutions. Beckhoff Support Support offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with other, wide-ranging services: • Support • design, programming and commissioning of complex automation systems • and extensive training program for Beckhoff system components Hotline: +49(0)5246/963-157 Fax: +49(0)5246/963-9157 E-mail: [email protected] Beckhoff Service The Beckhoff Service Center supports you in all matters of after-sales service: • on-site service • repair service • spare parts service • hotline service Hotline: +49(0)5246/963-460 Fax: +49(0)5246/963-479 E-mail: [email protected] Further Support and Service addresses can be found on our website at http://www.beckhoff.de. Beckhoff headquarters Beckhoff Automation GmbH & Co. KG Hülshorstweg 20 33415 Verl Germany Phone: +49(0)5246/963-0 Fax: +49(0)5246/963-198 E-mail: [email protected] The addresses of Beckhoff’s branch offices and representatives round the world can be found on the internet pages: http://www.beckhoff.de You will also find further documentation for Beckhoff components there.

CB7268 80 Version: 1.1 12 Appendix I: Post Codes During the boot phase, the BIOS generates a series of status messages (so-called "POST Codes"), which can be output with the help of a suitable reading device (POST Code card). The meanings of the POST Codes are explained in the document "Aptio™ 5.x Status Codes" from American Megatrends®, which is available from the website http://www.ami.com. In addition, the following OEM POST Codes are output:  Code  Description  87h  BIOS-API started  88h  PCA9535 started  89h  PWRCTRL firmware started

CB7268 81 Version: 1.1 13 Appendix II: Resources 13.1 Interrupt CB7268 The system BIOS determines the interrupt requests (IRQs) for all devices that request interrupts. In the operating system, interrupts can be dynamically forwarded to IRQs and can support a reassignment of IRQs if there is a conflict with the current use of the interrupt. For further information please refer to the chipset manual.

CB7268 82 Version: 1.1 13.2 PCI devices CB7268 The PCI devices listed here all exist on the board, including those that are detected and configured by the BIOS. Due to the BIOS setup settings it may be the case that various PCI devices or functions of devices are not activated. If devices are deactivated, the bus numbers of other devices may change as a result.  Bus  Dev.  Fct.  Controller / Slot  00  00  00  Host bridge ID 3E35  00  02  00  VGA controller ID 3EA0  00  04  00  Data acquisition/signal processing controller ID 1903  00  08  00  System device ID 1911  00  12  00  Data acquisition/signal processing controller ID 9DF9  00  14  00  XHCI USB controller ID 9DED  00  14  02  RAM controller ID 9DEF  00  16  00  Communication device ID 9DE0  00  17  00  RAID controller ID 282A  00  1C  00  PCI-to-PCI bridge (PCIE) ID 9DB8  00  1C  07  PCI-to-PCI bridge (PCIE) ID 9DBF  00  1D  00  PCI-to-PCI bridge (PCIE) ID 9DB0  00  1D  03  PCI-to-PCI bridge (PCIE) ID 9DB3  00  1F  00  ISA bridge ID 9D84  00  1F  03  HD audio device ID 9DC8  00  1F  04  SMBus controller ID 9DA3  00  1F  05  Controller ID 9DA4  00  1F  06  Ethernet controller ID 15BD  02  00  00  Ethernet controller (PCIE) ID 1533  03  00  00  Mass storage controller (PCIE) ID 5008  04  00  00  Ethernet controller (PCIE) ID 1533

CB7268 83 Version: 1.1 13.3 SMB devices CB7268 The following table lists the reserved SM-Bus device addresses in 8-bit notation. NOTE These address ranges may not be used by external devices even if the component assigned in the table doesn't exist on the motherboard.  Address  Function  B0, B2, B8, BA  PWCTR3  70, 72  PostCode  34 (old B4)  CA2000-0021/23 (power supply unit)  40  PCA9535BS (16-bit I2C and SMBus, low power I/O port with interrupt) ..  SUSV

Hülshorstweg 20 33415 Verl Germany Phone: +49 5246 9630 [email protected] www.beckhoff.com