ABB ZLS924 Mounting Instruction

Notice de montage Bloc d’alimentation ZLS924 Mounting instruction Incoming Terminal Block ZLS924 2CCR181840B0001 May 2019 Warnung  Nichtbefolgung dieser Hinweise kann zu tödlichen Ver- let zungen oder zu Sachschäden führen. Das Gerät darf nur von einer elektrotechnisch unterwiesenen Person in- stalliert werden. Vor Beginn der Installation ist die Netz- spannungszufuhr abzuschalten. Sicherheit Es dürfen ausschliesslich die oberflächenveredelten Sammelschienen von ABB verwendet werden. Am Stecksockel-System dürfen keine Reparaturen vorge- nommen werden. Entsorgung Defekte Geräte sind als Sondermüll an entsprechend eingerichteten Sammelstellen zu entsorgen. Nationa- le oder regionale Vorschriften über die Entsorgung von Son der müll sind zu befolgen. Avertissement F Le non-respect des présentes instructions peut entraîner la mort, des blessures corporelles ou des dégâts matériels. L’appareil doit uniquement être ins- tallé par une personne qualifiée. Coupez l’alimentation électrique principale avant de commencer l’installation. Sécurité Utiliser exclusivement les barres collectrices à surface améliorée de ABB. Ne procéder à aucune sorte de répa- ration sur le système de socle d’enfichage. Elimination Les appareils défectueux sont à éliminer en tant que déchets spéciaux sur les lieux de collecte prévus à cet effet. Respecter les prescriptions nationales ou régio- nales. Warning G Failure to follow these instructions could result in death, personal injury or property damage. The device should be installed by a qualified person only. Turn off power at the main power supply before beginning installation. Safety Only the surface-coated bus bars from ABB may be used. Do not attempt to repair a damaged plug-in socket system. Replace damaged components with new components. Disposal Faulty products should be treated as hazardous waste and disposed of in an appropriate manner. National or regional regulations regarding the disposal of hazardous waste should be adhered to. Warning! Installation by person with electrotechnical expertise only. Warnung! Installation nur durch elektrotechnische Fachkraft. Avvertenza! Fare installare solo da un elettricista qualificato. Avertissement! Installation uniquement par des personnes qualifiées en électrotechnique. ¡Advertencia! La instalación deberá ser realizada únicamente por electricistas especializados. WARNING HAZARD OF EQUIPMENT DAMAGE • Use only material manufactured by ABB. • Not following these instructions might result in severe injuries or death or equipment damage. • This product is NOT suitable for use in installation equipment any other than the SMISSLINE SYSTEM. • ABB doesn’t assume responsibility for any consequences arising out of the use of this equipment WARNING HAZARD OF ELECTRIC SHOCK, INJURY, BURN OR EXPLOSION • Make sure ALL electrical power supplies are “OFF” before installing or removing any devices or busbars. • The Incoming Terminal block and compo- nent MUST ONLY be installed and serviced by QUALIFIED personnel. • Always use properly rated voltage sensing device to confirm the power is off. • All devices, doors and covers must be replaced before switching on the power to this equipment IEC data  Technische Daten F Caractéristiques techniques G Technical data • Einspeiseblock: • Bloc d’alimentation standard: • Incoming Terminal Block, Standard: Max. Bemessungsspannung: Tension nominale max.: Maximum Rated Voltage: 690 VAC Max. Bemessungstrom: Intensité nominale max.: Maximum Rated Current: 160 A Hauptklemme: Borne principale: Main Terminal: 6 mm2 up 50 mm2 2 x 25 mm2 flexible wire with ferrules Flat cable 9 x 2 x 0,8 up to 9 x 9 x 0,8 mm, Cu only Hilfsklemme: Borne auxiliaire: Auxiliary terminal: 1,5 mm2 up 10 mm2 Stranded with ferrules Cu only UL data For all types: Feeder Blocks cat. nos. ZLS924 are suitable for use in feeder circuits up to 250 V Rated Voltage: 600 V AC Rated Current (side feed, left or right): 150 A Short Circuit Protection: 150 A Fuse or 250 A Circuit-Breaker (DIVQ/7) Torque: 4.0 Nm (L,N); 1.5 Nm (LA, LB); 1.2 Nm Cover screw Stripping length: 18 mm (L,N); 11 mm (LA, LB) Wire size: 10 AWG - 1/0 AWG, Cu only Wire rated min. 600 V and 75 °C (AVLV2/8)

Fig. 3–9 IP20B Berührungsschutz muss beim Ausbrechen berücksichtigt werden Fig. 10 Einspeisebeispiele SMISSLINE 125 A System Fig. 11–14 Montage sur les socles, Bloc d’alimentation F Fig. 1 Démontage, Bloc d’alimentation Fig. 2 Colonnes montantes continues, Bloc d’alimentation Fig. 3–9 La protection de contact IP20B doit être prise en compte lors de l'éclatement Fig. 10 Exemples d’alimentation SMISSLINE 125 A système Fig. 11–14 Assembly to plug-in socket system, G Incoming Terminal Block Fig. 1 Disconnection, Incoming Terminal Block Fig. 2 Ring feed, Incoming Terminal Block Fig. 3–9 IP20B touch proof protection must be considered when breaking out Fig. 10 Supply variants SMISSLINE 125 A system Fig. 11–14 ABB Switzerland Ltd Low Voltage Products Fulachstrasse 150 CH-8200 Schaffhausen Phone: +41 58 586 41 11 Fax: +41 58 586 42 22 www.abb.com ABB Inc. 8155 T&B Blvd. Memphis, TN 38125 Technical Support: E-Mail: [email protected] Phone: 1-888-385-1221 Option 1 > 30° max. 125 A max. 125 A max. 250 A (UL+IEC), same cable length max. 125 A max. 125 A max. 150 A (UL) max. 160 A (IEC) max. 125 A (UL+IEC) 1 4 7 10 2 5 3 6 6a 8 9 max. 125 A max. 125 A max. 250 A (UL+IEC) max. 125 A max. 125 A 13 12 11 14