modway EEI-3189 Manual
Read Online
Read the modway EEI-3189 Manual online using the built-in PDF viewer.
Text of the manual
EEI –3189 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 5
Thank you for purchasing the MODWAY OFFICE CHAIR.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembled time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
A. Bolt M6x20mm x 8
B. Bolt M6x35mm x 4
C. Flat Washer 18mm x 8
D. Flat Washer 14mm x 4
E. Allen Wrench x1
F. Cover x4
Component:
1
Base x1 2 Cylinder Column x1 3 Control Mechanism x1 4 Seat x1 5 Back Frame x1
6 Left Arm x1 7 Right Arm x1 8 Castor x5 9 Round casing x1
8
2
1
9
3
7
5
4
6
EEI –3189 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 5
STEP 1:
Please put Base (1) on a carpeted or padded surface.
Insert 1 piece of Castor (8) into the Base (1) as shown by hand. Repeat the same steps for the remaining 4
pieces of Castors (8).
STEP 2:
Carefully turn over the assembled Base (1) from step 1.
Insert the Cylinder Column (2) and Round casing (9) to Base (1) as shown.
8
1
8
8
8
8
2
1
9
EEI –3189 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 5
STEP 3:
Attach Left Arm (6) and Right Arm (7) to the both side of Back (6) by using 4 pieces of Bolts (A) with 4 pieces of
Flat Washers (C) as shown.
Tighten Bolts (A) by using Allen Wrench (E) as shown.
Hardware & Tools required
STEP 4:
Attach Cap Cover (F) to the holes on Left Arm (6) and Right Arm (7) by hand as shown.
Hardware & Tools required
A
x 4
x 4
x 1
E
D
A
D
E
5
6
7
F
x 4
F
F
5
6
7
EEI –3189 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 5
STEP 5:
Attach assembled unit to the Seat (4) by using 4 pieces of Bolts (B) and 4 pieces of Flat Washers (C) as shown.
Tighten Bolts (B) by using Allen Wrench (E) as shown.
Hardware & Tools required
STEP 6:
Attach Control Mechanism (3) to the assembled Seat (4) by using 4 pieces of Bolts (A) and 4 pieces of Flat
Washers (C) as shown. Tighten Bolts (A) by using Allen Wrench (E) as shown.
Hardware & Tools required
B
x 4
x 4
x 1
E
C
B
C
E
5
6
7
4
5
6
7
A
C
E
4
3
A
x 4
x 4
x 1
E
C
EEI –3189 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5 of 5
STEP 7:
Insert assembled Control Mechanism (3) into the Cylinder Column (2) as shown.
STEP 8:
Assembly is complete. Your office chair is ready to be used now!
1
3
7
5
8
4
6
2
9
