Craftsman 358.795500 Instruction Manual

17 Inch Cutting Path / 0.080 Inch Line GASOLINE WEEDWACKER ® Model No. 358.795500 y Safety p_ _" : Assembly _,4_" Operation J'V • Maintenance / • Parts List _ • Espa_ol /"_ For Occasional Use Only WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun. 1-800-235-5878 _.o._ listed are Central Time) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 530163584 12/19/02

15 Parts and Ordering Back Cover FULL ONE YEAR WARRANTY ON CRAFTSMAN ® GASOLINE POWERED WEEDWACKER ® LINE TRIMMER. For one year from the date of purchase, when this Craftsman Gasoline Powered Weedwacker Line Trimmer is maintained, lubricated, and tuned up according to the operating and maintenance instructions in this manual, Sears will repair, free of charge, any defect in materials or workmanship. This warranty excludes nylon line, spark plug, and air filter, which are expendable parts and become worn during normal use. If this Weedwacker Line Trimmer is used for commercial purposes, this warranty ap- plies for only 90 days from the date of purchase. If this Weedwacker Line Trimmer is used for rental purposes, this warranty applies for only 30 days from the date of pur- chase. This warranty applies only while this product is in use in the United States. WARRANTYSERVICE IS AVAILABLE BY RETURNINGTHE WEEDWACKER LINETRIMMER TO THE NEARESTSEARS STORE OR SERVICECENTER INTHE UNITEDSTATES. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179 Only the following Gasoline Powered Combination Gardening Appliance power- head models and their respective attachments have been Classified by Under- writers Laboratories, Inc., in accordance with the applicable safety requirements. Powerhead including trimmer attachment .................... 358.795500 Optional brushcutter attachment ............................ 358.792430 Optional blower attachment ................................ 358.792421 The following attachment is Lis!ed by Underwriter's Laboratories, Inc., in accor- dance with UL Standard 1602, Gasoline-Engine-Powered, Rigid-Cutting Mem- ber Edgers and Edge-Trimmers." Optional edger attachment ................................. 358.792400 2

dening appliances, basic safety pre- cautions must always be followed to reduce the risk of fire and serious injury. Read and follow all instructions. This power unit can be dangerous! Op- erator is responsible for following instructions and warnings on unit and in manual. Read entire instruction manual before using unit! Be thoroughly familiar with the controls and the proper use of the unit. Restrict the use of this unit to persons who have read, understand. and will follow the instructions and warnings on the unit and in the manual. Never allow children to operate this unit. INSTRUCTION SAFETY INFORMATION MANUAL ON THE UNIT DANGER: Never use blades with line trimmer attachment. Never use flailing devices with any attach- ment. This unit (when used with sup- plied line trimmer attachment) is de- signed for line trimmer use only. Use of any other accessories with line trim- mer attachment will increase the risk of injury.O@@ 4re.WARNING: Trimmer line throws objects violently. You and others can be blinded/injured. Wear eye and leg protection. Keep body parts clear of ro- tating line. Eye Protection HazardZone '.\-- Keep children, bystanders, and animals 50 feet (15 meters) away. Stop unit im- mediately if approached. If situations occur which are not cov- ered in this manual, use care and good judgment. If you need assis- tance, contact your Sears Service Center or call 1-800-235-5878. OPERATOR SAFETY • Dress properly. Always wear safety glasses or similar eye protection when operating, or performing main- tenance, on your unit (safety glasses are available). Eye protec- tion should be marked Z87. • Always wear face or dust mask if op- eration is dusty. • Always wear heavy, long pants, long sleeves, boots, and gloves. Wear- ing safety leg guards is recom- mended. • Always wear foot protection. Do not go barefoot or wear sandals. Stay clear of spinning line. • Secure hair above shoulder length. Secure or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts. • Being fully covered also helps pro- tect you from debris and pieces of toxic plants thrown by spinning line. • Stay Alert. Do not operate this unit when you are tired, ill, upset or un- der the influence of alcohol, drugs, or medication. Watch what you are doing; use common sense. • Wear hearing protection. • Never start or run inside a closed room or building. Breathing exhaust fumes can kill. • Keep handles free ofoil and fuel. • Always keep engine on the right • hand side of your body. Hold the unit firmly with both hands. • Keep trimmer head (or other option- al attachment) below waist level and away from all parts of your body. Do not raise engine above your waist. • Keep all parts of your body away from muffler and spinning line (or other optional attachment). Keep engine below waist level. A hot muf- fler can cause serious burns. • Keep firm footing and balance. Do not overreach or use from unstable surfaces such as ladders, trees, steep slopes, rooftops, etc. • Use only in daylight or good artificial light. • Use only for jobs explained in this manual (or manuals for optional at- tachments). 3

SAFETY • Disconnect the spark plug before performing maintenance except car- buretor adjustments. • Look for and replace damaged or loose parts before each use. Look for and repair fuel leaks before use. Keep in good working condition. • Replace trimmer head parts that are chipped, cracked, broken, or dam- aged in any other way before using the unit. • Maintain unit according to recom- mended procedures. Keep cutting line at proper length. • Use only 0.080 inch (2 mm) diame- ter Craftsman® brand line. Never use wire, rope, string, etc. • Install required shield properly be- fore using the unit. Use only speci- fied trimmer head; make sure it is properly installed and securely fas- tened. • Make sure unit is assembled cor- rectly as shown in this manual. • Make carburetor adjustments with lower end supported to prevent line from contacting any object. • Keep others away when making car- buretor adjustments. • Use only recommended Craftsman accessories and replacement parts. • Have all maintenance and service not explained in this manual per- formed by a Sears Service Center. FUEL SAFETY • Mix and pour fuel outdoors. • Keep away from sparks or flames. • Use a container approved for fuel. • Do not smoke or allow smoking near fuel or the unit. • Avoid spilling fuel or oil. Wipe up all fuel spills. • Move at least 10 feet (3 meters) away from fueling site before start- ing engine. • Stop engine and allow to cool before removing fuel cap. • Always store gasoline in a container approved for flammable liquids. TRANSPORTING AND STORAGE • Allow engine to cool before storing or transporting in vehicle. • Empty the fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting the en- gine and letting it run until it stops. • Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. • Store unit so line limiter blade can- not accidentally cause injury. The unit can be hung by the tube. • Store unit out of reach of children. SAFETY NOTICE: Exposure to vibra- tions through prolonged use of gaso- line powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or ab- normal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti- vibration system does not guarantee the avoidance of these problems. Us- ers who operate power tools on a con- tinual and regular basis must monitor closely their physical condition and the condition of this tool. SPECIAL NOTICE: This unit is equipped with a temperature limiting muffler and spark arresting screen which meets the requirements of Cali- fornia Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion en- igines be equipped with a spark arrest- ng screen, if you operate in a locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by a Sears Service Center. LINE TRIMMER SAFETY _ WARNING: Inspect the area to be trimmed before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard ob- jects can damage the trimmer head and be thrown causing serious injury. • Use only for trimming, scalping, mow- ing and sweeping. Do not use for edging, pruning or hedge trimming. • Cut only from your right to your left. Cutting on left side of the shield will throw debris away from the operator. 4

_ WARNING: For each optional attachment used, read entire opera- tors manual before use and follow all warnings and instructions in manual and on attachment. i_ WARNING: Ensure handlebar is installed when using edger or brush- cutter attachments. Attach handlebar above arrow on safety label on the up- per tube (engine end of unit). If your edger or brushcutter attachment does not include a handlebar, a handlebar accessory kit (#530071451) is avail- able from your Sears Service Center. _Han61ebar EDGER SAFETY _WARNING: Inspect the area to be edged before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by the blade or can wrap around the shaft. * Blade rotates momentarily after the trigger is released. The blade can seriously cut you or others. * Allow blade to stop before removing it from the cut. Blade rotates * Throw away blades that are bent, warped, cracked, broken or dam- aged in any other way. Replace parts that are cracked, chipped, or damaged before using the unit. * Do not attempt to remove cut materi- al nor hold material to be cut when the engine is running or when cut- ting blade is moving. * Always keep the wheel and depth adjusting skid in contact with the ground. • Always push the unit slowly over the ground. Stay alert for uneven side- walks, holes in the terrain, large roots, etc. • Always use the handlebar when us- ing edger attachment. BLOWER/VACUUM SAFETY _WARNING: Inspect area before starting unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. • Do not set unit on any surface ex- cept a clean, hard area while engine is running. Debris such as gravel, sand, dust, grass, etc., could be picked up by the air intake and thrown out through discharge open- ing, damaging unit, property, or causing serious injury to bystanders or operator. • Never place objects inside the blow- er tubes, vacuum tubes or blower outlet. Always direct the blowing de- bris away from people, animals, glass, and solid objects such as trees, automobiles, walls, etc. The force of air can cause rocks, dirt, or sticks to be thrown or to ricochet which can hurt people or animals, break glass, or cause other damage. • Never run unit without the proper equipment attached. When using your unit as a blower, always install blower tubes. • Check air intake opening, blower tubes or vacuum tubes frequently, always with engine stopped and spark plug disconnected. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow. • Never place any object in air intake opening as this could restrict proper air flow and cause damage to the unit. • Never use for spreading chemicals, fertilizers, or other substances which may contain toxic materials. • To avoid spreading fire, do not use near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc. 5

Blade thrust can cause amputation of arms or legs. _ WARNING: Do not use trimmer head as a fastening device for the blade. se • Use only specified blade and make sure it is properly installed and se- curely fastened. • Cut from your right to your left. • Always use the handlebar and a properly adjusted shoulder strap with blade (see ASSEMBLY instruc- tions in brushcutter attachment in- struction manual). CULTIVATOR SAFETY i_ WARNING: Rotating tines can cause serious injury. Keep away from rotating tines. Stop the engine and disconnect the spark plug before un- clogging tines or making repairs. _ WARNING: The blade contin- ues to spin after the throttle is re- leased or engine is turned off. The coasting blade can throw objects or seriously cut you if accidentally touched. Stop the blade by contacting the left hand side of the coasting blade with material already cut. Stop coasting blade by contact with cut material, ® 4re.WARNING: Inspect the area to be cut before each use. Remove ob- jects (rocks, broken glass, nails, wire. etc.) which can be thrown or become entangled in the blade or trimmer line. • Throw away and replace blades that are bent. warped, cracked, broken or damaged in any other way. • Install required shield properly be- fore using the unit. Use the metal shield for all metal blade use. _ WARNING: Only use brushcut- ter attachments that provide a metal shield with proboscis nose. _ WARNING: Inspect the area to be cultivated before starting the unit. Remove all debris and hard and sharp objects such as rocks, vines, branch- es, rope, string, etc. • Avoid heavy contact with solid ob- jects that might stop the tines. If heavy contact occurs, stop the en- gine and inspect the unit for dam- age. • Never operate the cultivator without the tine cover in place and properly secured. • Keep the tines and guard clear of debris. • After striking a foreign object, stop the engine, disconnect the spark plug and inspect the cultivator for damage. Repair before restarting. • Disconnect attachment from the drive engine before cleaning the tines with a hose and water to re- move any build-up. Oil the tines to prevent rust. • Always wear gloves when servicing or cleaning the tines. The tines be- come very sharp from use. • Do not run unit at high speed unless cultivating. 6

HANDS AWAY FROM BLADE - Blade moves momentarily after the trigger is released. Do not attempt to clear away cut material when the blade is in motion. Make sure the switch is in the OFF posi- tion, the spark plug wire is discon- nected, and the blade has stopped moving before removing jammed mate- rial from the cutting blade. Do not grab or hold the unit by the cutting blade. Blades move momentarily after the trigger s d. Allow blades to stop before removing them from the cut. _ WARNING: Inspect the area be- fore starting the unit. Remove all de- bris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. * Do not use a cutting blade that is bent, warped, cracked, broken or damaged in any other way. Have worn or damaged parts replaced by your Sears Service Center. * Always keep unit in front of your body. Keep all parts ofyour body away from the cutting blade. * Keep the cutting blade and air vents clear of debris. POLE PRUNER SAFETY _ WARNING: The reciprocating blade/rotating chain can cause severe injury. Inspect the unit before use. De not operate unit with a bent, cracked or dull blade or dull chain. Keep away from the blade/chain. _ WARNING: The reciprocating blade/rotating chain is sharp. Do not touch. To prevent serious injury, al- ways stop engine and ensure blade/ chain has stopped moving, disconnect spark plug, and wear gloves when changing or handling the blade or chain. _ WARNING: A coasting blade/ro- tating chain can cause injury while it continues to move after the engine is stopped. Maintain proper control of the unit until the blade/chain has completely stopped moving. Keep hands, face and feet at a distance from all moving parts. Do not attempt to touch or stop the blade or chain when it is moving. _ WARNING: Falling objects can cause severe head injury. Wear head protection when operating this unit with a pole pruner attachment. O _ WARNING: To prevent serious injury, do not use more than one boom extension with a pole pruner attach- ment. _ WARNING: Keep the pruner away from power lines or electrical wires. • Only use for pruning limbs or branches up to 4 inches in diameter. • Do not operate the unit faster than the speed needed to prune. Do not run the unit at high speed when not pruning. • Always stop the unit when work is delayed or when walking from one cutting location to another. • If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Have any damage repaired by a Sears Service Center before at- tempting further operations. Discard blades that are bent, warped, cracked or broken. • Stop the unit immediately if you feel excessive vibration. Vibration is a sign of trouble. Inspect thoroughly for loose nuts, bolts or damage be- fore continuing. Contact Sears Ser- vice for repair or replacement of af- fected parts as necessary. 7

feet away from the rotor when starting or running the engine. Never attempt to clear the rotor with the engine/motor running. Stop engine and disconnect spark plug before unclogging snow or debris from discharge chute or when adjusting vanes. _ WARNING: Never lean over dis- charge chute. Rocks or debris could be thrown into the eyes and face and cause serious injury or blindness. _ WARNING: Inspect the area where the unit is to be used. Remove objects that could be thrown or dam- age the unit. Some objects may be hidden by fallen snow - be alert for the possibility. • Direct material discharge away from glass enclosures, automobiles, etc. • Do not run engine at high speed while not removing snow. • Be attentive when using the snow- thrower, and stay alert for holes in the terrain and other hidden haz- ards. • Make sure the rotor will spin freely before attaching the snowthrower to the powerhead. • If the rotor will not rotate freely due to frozen ice, thaw the unit before thoroughly before attempting to op- erate under powen • Keep the rotor clear of debris. • Do not throw snow near other people. The snow thrower could propel small objects at high speed causing injury. • After striking a foreign object, stop the engine, disconnect spark plug and inspect the snowthrower for damage and repair if necessary be- fore restarting unit. • Never operate the snowthrower near glass enclosures, automobiles and trucks. • Never attempt to use the snow- thrower on a roof. • Never operate the snowthrower near window wells, dropoffs, etc. • Never discharge snow onto public roads or near moving traffic. • Clear snow from slopes by going up and down; never across. Use cau- tion when changing directions. Nev- er clear snow from steep slopes. • Let snowthrower run for a few min- utes after clearing snow so moving parts do not freeze. • Look behind and use care when backing up. Exercise caution to avoid slipping or falling, especially when operating in reverse. • Know how to stop quickly. 8

against the fol- lowing list. Model 358.795500 • Powerhead • Trimmer Attachment • Shield • Wing Nut (screwed onto shield) • Container of Oil Examine parts for damage. Do not use damaged parts. NOTE: If you need assistance or find parts missing or damaged, call 1-800-235-5878. It is normal for the fuel filter to rattle in the empty fuel tank. Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer. ASSEMBLY _ WARNING: If received as- sembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. INSTALLING TRIMMER ATTACH- MENT CAUTION: When installing trimmer attachment, place the unit on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Coupler LOOSEN TIGHTEN Knob 2. Remove the tube cap from the trimmer attachment (if present). 3. Position locking/release button of attachment into guide recess of coupler. 4. Push the attachment into the cou- pler until the locking/release button snaps into the primary hole. 5. Before using the unit, tighten the knob securely by turning clock- wise. Coupler Primary Hole \ / Guide Recess Upper oc ' g/ Lower Tube Release Attachment Button _ WARNING: Make sure the lock- ing/release button is locked in the pri- mary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole. For optional attachments, see the AS- SEMBLY section of the applicable at- tachment instruction manual. ATTACHING SHIELD i_ WARNING: The shield must be properly installed. The shield provides partial protection from the risk of thrown objects to the operator and others and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on under- side of shield) is sharp and can cut you. For proper orientation of shield, see KNOWYOURTRIMMER illustration in OP- ERATIONsection. 1. Remove wing nut from shield. 2. insert bracket into slot as shown. 3. Pivot shield until bolt passes through hole in bracket. 4. Securely tighten wing nut onto bolt. Shield _NjS lot k _ ,_\_ Bracket _ng Line Limiter Blade Nut ADJUSTING THE HANDLE _WARNING: When adjusting the handle, be sure it remains between the trigger and the arrow on the safety label. 1. Loosen wing nut on handle. 2. Rotate the handle on the tube to an upright position; retighten wing nut. 9

READ THIS INSTRUCTIONMANUALAND SAFETY RULES BEFOREOPERATINGYOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Assist Handle Coupler Tube Trimmer "-& ON/OFF Switch Head Starter Shield Handle / Spark Plug / Line Limiter Blade Throttle Muffler Trigger Lever Primer Bulb ON/OFF SWITCH The ON/OFF switch is located on the trigger handle and is used to stop the engine. Move the switch to the OFF position to stop the engine. PRIMER BULB The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form. START LEVER The START LEVER helps to supply fuel to the engine to aid in starting. Acti- vate the starting system by moving the start lever to the START position. DO NOT squeeze the throttle trigger until the engine has started and runs. After the engine starts, allow the engine to warm-up 10-15 seconds, then fully squeeze the throttle trigger to deacti- vate the starting system. COUPLER The COUPLER enables optional at- tachments to be installed on the unit. BEFORE STARTING ENGINE WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not under- stand the safety rules, do not attempt to fuel your unit. Call 1-800-235-5878. FUELING ENGINE _WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil. We recommend Craftsman brand synthetic oil. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline. included with this trimmer is a 3.2 ounce container of oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit. 10

and formation of acids during storage. Acidic gas can damage the fuel sys- tem of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may oc- cur. See the STORAGE section for additional information. HOW TO STOP YOUR UNIT • To stop the engine, move the ON/OFF switch to the OFF position. _lb_ ON/OFF Thro_le Trigger _ HOW TO START YOUR UNIT i_ WARNING: The trimmer head will turn while starting the engine. Avoid any contact with the muffler. A hot muffler can cause serious burns. STARTING A COLD ENGINE NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs. 1. Set unit on a flat surface. 2. Move ON/OFF switch to the ON position. 3. Slowly press the primer bulb 6 times. 4. Move the start lever to the START position. Primer Bulb 5. Pull starter rope handle sharply until engine starts and runs. 6. Allow unit to run for 10-15 seconds, then fully squeeze the throttle trigger to disengage the starting system. STARTING A WARM ENGINE 1, Move ON/OFF switch to the ON position, 2, Move the start lever to the RUN position, 3, Squeeze and hold the throttle trig- ger, Keep throttle trigger fully squeezed until engine runs smoothly, 4, Pull starter rope sharply while squeezing throttle trigger until en- gine runs. NOTE: Normally, the warm starting procedure can be used within 5-10 minutes after the unit is turned OFF. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit. STARTING A FLOODED ENGINE Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter handle repeat- edly while squeezing throttle trigger until engine starts and runs. This could require pulling the starter handle many times, depending on how badly the unit is flooded. 11

TROUBLESHOOTING TABLE or call 1-800-235-5878. OPERATING THE COUPLER This model is equipped with a coupler which enables optional attachments to be installed. The optional attach- ments are: Edger ................. 358.792400 Cultivator .............. 358.792410 Blower ................ 358.792421 Brushcutter ............ 358.792430 411.WARNING: Always stop unit and disconnect spark plug before re- moving or installing attachments, REMOVING TRIMMER ATTACH* MENT (OR OTHER OPTIONAL AT- TACHMENTS) CAUTION: When removing or instal- ling attachments, place the unit on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. UpperTube Coupler Coupler Primary Hole Upper Locking/ Attachment Tube Release Button _ WARNING: Make sure the lock- ing/release button is locked in the pri- mary hole and the knob is securely tightened before operating the unit. OPERATING POSITION ALWAYS WEAR: _.,x Eye Protection Heavy Shoes _1_[t_ Lower Attachment TIGHTEN Knob 2. Press and hold the locking/release button. Locking/Release Button / LowerAttachment UpperTube 3. While securely holding the engine and upper tube, pull the attach- ment straight out of the coupler. INSTALLING OPTIONAL ATTACH* MENTS 1, Remove the tube cap from the at- tachment (if present), 2. Position locking/release button of attachment into guide recess of coupler. 3. Push the attachment into the cou- pler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clock- wise. Cut only from your right to your left. _ WARNING: Always wear eye protection, Never lean over the trim- mer head. Rocks or debris can rico- chet or be thrown into eyes and face and cause blindness or other serious injury. When operating unit, stand as shown and check for the following: • Wear eye protection and heavy clothing. • Hold trigger handle with right hand and assist handle with left hand. • Keep unit below waist level. • Cut only from your right to your left to ensure debris is thrown away from you. Without bending over, keep line near and parallel to the ground and not crowded into materi- al being cut. Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to "weld" onto the spool. Always release the throttle trigger and allow the engine to return to idle speed when not cutting. 12

• Release the throttle trigger. • Move the ON/OFF switch to the OFF position. TRIMMER LINE ADVANCE The cutting head advances line au- tomatically. Do not tap head on the ground to advance line. This may break parts and cause cutting head to malfunction. Upon unit start up, the line will advance automatically to the correct cutting path length. Always keep the shield in place when the tool is being operated. WARNING: Use only 0.080" (2 mm) diameter round line. Other sizes and shapes of line will not ad- vance properly and will result in im- proper cutting head function or can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury. CUTTING METHODS I_WARNING: Use minimum speed and do not crowd the line when cutting around hard ob ects (rock, gravel, fence posts, etc.), wh ch can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard. • The tip of the line does the cutting. You will achieve the best perform- ance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below. Tip of the Line I Line Crowded Into Does The Cutting Work Area Right .... Wrong "_'_---- • The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. • For trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially: • During light duty cutting. • Near objects around which the line can wrap such as small posts, trees or fence wire. • For mowing or sweeping, use full throttle for a good clean job. TRIMMING - Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area. Trimming 3 in. (8 cm) Above Ground SCALPING - The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear. Scalping MOWING - Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool. Mowing 13

the rotating line can be used to blow away loose debris from an area, Keep the line parallel to and above the area surface and swing the tool from side to side. Sweeping _ MAINTENANCE SCHEDULE WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments. CARE & MAINTENANCE TASK Check for loose fasteners and parts Check for damaged or worn parts Inspect and clean unit and labels Clean air filter Inspect muffler and spark arresting screen Replace spark plug _ENERAL RECOMMENDATIONS The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various ad- justments will need to be made peri- odically to properly maintain your unit. WHEN TO PERFORM Before each use Before each use After each use Every 5 hours of operation Every 50 hours of operation Yearly • Wipe off unit with a clean dry cloth. CLEAN AIR FILTER A dirty air filter decreases engine per- formance and increases fuel con- sumption and harmful emissions. Al- ways clean after every 5 hours of operation. 1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when CHECK FOR LOOSE FASTENERS AND PARTS , Spark Plug Boot * Air Filter * Housing Screws * Assist Handle Screw * Debris Shield CHECKFORDAMAGED OR the cover is removed, 2. Remove parts by pressing latch to release air filter cover. NOTE: To avoid creating a fire hazard or producing harmful evaporative emissions, do not clean filter in gaso- line or other flammable solvent. 3. Wash the filter in soap and water. WORN PARTS 4. Contact Sears Service Center for re- 5. placement of damaged or worn parts. • ON/OFF Switch - Ensure ON/OFF 6. switch functions properly by moving the switch to the OFF position. Make sure engine stops; then restart en- gine and continue. • Fuel Tank - Discontinue use of unit if fuel tank shows signs of damage or leaks. • Debris Shield - Discontinue use of unit if debris shield is damaged. INSPECT AND CLEAN UNIT AND LABELS , After each use, inspect complete unit for loose or damaged parts, Clean the unit and labels using a damp cloth with a mild detergent. Allow filter to dry, Add a few drops of oil to the filter; squeeze the filter to distribute oil. Replace parts. _ilter Cover Latch REPLACE SPARK PLUG Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch. Ignition timing is fixed and nonadjustable. 14

2. Remove spark plug from cylinder and discard. 3. Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch socket wrench. 4. Reinstall the spark plug boot. LINE REPLACEMENT Pre-wound spools offer the most con- venient method for replacing line and ensuring optimum performance. * Replacement spools are color- coded to ensure use of the correct spool with your unit. Be sure to use the same color spool as the existing spool. NOTE: Always clear dirt and debris from cutting head components when performing any type of maintenance. * Hold spool andunscrew cap by turn- ing in the direction shown on top of the cap. * Remove line guide ring and spool. Line guide ring Cap \ Use a pre-wound spool or refill spool with line. If using a pre-wound spool, remove tape strip from line and spool. REFILLING THE SPOOL WITH LINE i_ WARNING: Use only 0.080 inch (2 mm) diameter round line. Other sizes and shapes of line will not advance properly and will result in im- proper cutting head function or can cause serious in ury. Do not use other mater a s such as w re, str ng, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury. 1. Cut a length of 25 feet of 0.080 inch (2 ram) diameter round Craftsman brand line. _> Feeedtiiionn e in on Spool 2. insert one end of line into center cavity of empty spool. Ensure line will feed into spool in the direction shown on the spool (counterclock- wise). 3. Continue feeding line into spool, leaving 4 - 6 inches (10 - 15 cm) unwound from center of spool. INSTALLING SPOOL WITH LINE 1. Install replacement spool. 2. Thread line through line guide ring. Line through guide ring 1 Sio Replacement Spool 3. Rest guide ring on spool and place line through slot. Allow line to ex- tend 4 - 6 inches (10 - 15 cm) from center of spool. 4. Ensure line remains in slot while screwing cap on to the shaft. Only tighten cap hand tightI CARBURETOR ADJUSTMENT i_ WARNING: Keep others away when making idle speed adjustments. The trimmer head or any optional at- tachment will be spinning during most of this procedure. Wear your protec- tive equipment and observe all safety precautions. After making adjust- ments, the trimmer head or any op- tional attachment must not move/spin at idle speed. 15

released. • The trimmer head or optional attach- ment moves/spins at idle. Make ad ustments with the unit sup- ported so the cutt ng attachment s off the ground and will not make contact with any object. Hold the unit by hand while running and making adjust- ments. Keep all parts of your body away from the cutting attachment and muffler. Idle Speed Adjustment Allow engine to idle. Adjust speed until engine runs without trimmer head or optional attachment moving or spin- ning (idle too fast) or stalling (idle speed too slow). • Turn idle speed screw clockwise to increase engine speed if engine stalls or dies. • Turn idle speed screw counterclock- wise to decrease engine speed if trimmer head or optional attachment moves or spins at idle. i_ WARNING: Recheck the idle speed after each adjustment. The trimmer head or optional attachment must not move or spin at idle speed to avoid serious injury to the operator or others. Speed Screw Air Filter Cover If you require further assistance or are unsure about performing this proce- dure, contact your Sears Service Cen- ter or call our customer assistance help line at 1-800-235-5878. _ WARNING: Perform the follow- ing steps after each use: • Allow engine to cool before storing or transporting. • Store unit and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. • Store unit with all guards in place. Position unit so that any sharp ob- ject cannot accidentally cause injury. • Store unit and fuel well out of the reach of children. SEASONAL STORAGE Prepare unit for storage at end of sea- son or if it will not be used for 30 days or more. If your unit is to be stored for a period of time: • Clean the entire unit before lengthy storage. • Store in a clean dry area. • Lightly oil external metal surfaces. FUEL SYSTEM Under FUELING ENGINE in the OPERA- TION section of this manual, see mes- sage labeled IMPORTANT regarding the use of gasohol in your engine. Fuel stabilizer is an acceptable alter- native in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run engine at least 5 min- utes after adding stabilizer. Craftsman 40:1, 2-cycle engine oil (air cooled) is already blended with fuel stabilizer. ]f you do not use this Sears oil, you can add a fuel stabilizer to your fuel tank. ENGINE • Remove spark plug and pour 1 tea- spoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. • Replace spark plug with new one of recommended type and heat range. • Clean air filter. • Check entire unit for loose screws, nuts, and bolts. Replace any dam- aged, broken, or worn parts. • At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio. OTHER • Do not store gasoline from one sea- son to another. • Replace your gasoline can if it starts to rust. 16

spark plug before perform- ing all of the recommended remedies below except remedies that require TROUBLE Engine will not start. Engine will not idle properly. Engine will not accelerate, lacks power, or dies under a load. Engine smokes excessively, Engine runs hot. operation of the unit. CAUSE REMEDY 1. Move ON/OFF switch to ON. 1. ON/OFF switch in OFF position. 2. Fuel tank empty. 3. Spark plug not firing. 4. Fuel not reaching carburetor, 5. Carburetor requires adjustment. 1. Carburetor requires adjustment. 2. Crankshaft seals worn. 3. Compression low. 1. Air filter dirty. 2. Spark plug fouled. 3. Carburetor requires adjustment. 4. Carbon build-up on muffler outlet screen, 5. Compression low, 1. Fuel mixture incorrect, 2. Air filter dirty. 3. Carburetor requires adjustment. 1. Fuel mixture incorrect. 2. Spark plug incorrect. 3. Carburetor requires adjustment. 4. Carbon build-up on muffler outlet screen. 2. Fill tank with correct fuel mixture. 3. Install new spark plug. 4. Check for dirty fuel filter; replace, Check for kinked or split fuel line; repair or replace. 5. Contact Sears Service (see back cover) 1. See "Carburetor Adjustment" in Service and Adjustments Section, 2. Contact Sears Service (see back cover 3. Contact Sears Service (see back cover 1. Clean or replace air filter. 2. Clean or replace plug and regap. 3. Contact Sears Service (see back cover) 4. Contact Sears Service (see back cover) 5_ 1. 2_ 3. Contact Sears Service (see back cover) Empty fuel tank and refill with correct fuel mixture. Clean or replace air filter. Contact Sears Service (see back cover) 2. 3. 4. See "Fueling Engine" in Operation section. Replace with correct spark plug. Contact Sears Service (see back cover) Contact Sears Service (see back cover) YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U. S. Environ- mental Protection Agency and Sears, Roebuck and Co., U.S.A., are pleased to explain the emissions control system warranty on your year 2002-2004 small off-road engine. Sears must warrant the emission control system on your small off-road engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your small off-road en- gine. Your emission control system in- cludes parts such as the carburetor and the ignition system. Where a warrant- able condition exists, Sears will repair your small off-road engine at no cost to you, Expenses covered under warranty include diagnosis, parts and labor, MANUFACTURER S WARRANTY COVERAGE: If any emissions related part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or re- placed by Sears. OWNER'S WAR- RANTY RESPONSIBILITIES: As the small off-road engine owner, you are 17

the date the small off-road engine is purchased. LENGTH OF COVERAGE: This warranty shall be for a period of two years from the initial date of pur- chase. WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Re- pair or replacement of any warranted part will be performed at no charge to the owner at an approved Sears servic- ing center. If you have any questions regarding your warranty rights and re- sponsibilities, you should contact your nearest authorized service center or call Sears at 1-800-469-4663. WARRAN- TY PERIOD: Any warranted part which is not scheduled for replacement as re- quired maintenance, or which is sched- uled only for regular inspection to the effect of "repair or replace as neces- sary" shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required mainte- nance shall be warranted for the period of time up to the first scheduled replace- ment point for that part. DIAGNOSIS: The owner shall not be charged for diagnostic labor which leads to the de- termination that a warranted part is de- fective if the diagnostic work is per- formed at an approved Sears servicing center. CONSEQUENTIAL DAMAGES: Sears may be liable for damages to other engine components caused by the failure of a warranted part still under warranty. WHAT IS NOT COVERED: All failures caused by abuse, neglect, or improper maintenance are net covered. ADD-ON OR MODIFIED PARTS: The use of add-on or modified parts can be grounds for disallowing a warranty claim. Sears is net liable to cover fail- ures of warranted parts caused by the use of add-on or modified parts. HOW TO FILE A CLAIM: If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call Sears at 1-800-469-4663. WHERE TO GET WARRANTY SER- VICE: Warranty services or repairs shall be provided at all Sears service centers. Call 1-800-469-4663. MAINTE- NANCE, REPLACEMENT AND RE* PAIR OF EMISSION RELATED PARTS: Any Sears approved replace- ment part used in the performance of any warranty maintenance or repair on emission related parts will be provided without charge to the owner if the part is under warranty. EMISSION CONTROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug (covered up to maintenance schedule). Ignition Module. MAINTENANCE STATE- MENT: The owner is responsible for the performance of all required mainte- nance as defined in the instruction manual. This engine is certified to be emissions compliant for the following use: [] Moderate (50 hours) [] Intermediate (125 hours) [] Extended (300 hours) 18