Creative Broadband Blaster 8015U Operation & User’s Manual

Information in this document is subject to change without notice and does not represent a commitment on the part of Creative Technology Ltd. The software described in this document is furnished under a license agreement and may be used or copied only in accordance with the terms of the license agreement. It is against the law to copy the software on any other medium except as specifically allowed in the license agreement. The licensee may make one copy of the software for backup purposes. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the written permission of Creative Technology Ltd. Copyright © 2004 Creative Technology Ltd. All rights reserved. Version 1.1 September 2004 Broadband Blaster is a trademark of Creative Technology Ltd. IBM is a registered trademark of International Business Machines Corporation. Intel and Pentium are registered trademarks of Intel Corporation Microsoft, MS-DOS, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. Netscape Communicator is a trademark of Netscape Communications Corporation and may be registered outside the U.S. All other products are trademarks or registered trademarks of their respective owners.

Package Contents....................................................................................................................................... 1-v System requirements................................................................................................................................ 1-vi Using Ethernet connection........................................................................................................... 1-vi Using USB connection.................................................................................................................... 1-vi Using this document................................................................................................................................ 1-vii 1 About your DSL Router 2 Setting up your DSL Router using Ethernet connection Setting up your DSL Router................................................................................................................... 2-2 Using the Ethernet port................................................................................................................. 2-2 Configuring your Network Interface Card ...................................................................................... 2-4 In Windows XP/Windows 2000................................................................................................. 2-4 In Windows Me/Windows 98 SE............................................................................................... 2-7 3 Setting up your DSL Router using USB connection Installing the USB Driver......................................................................................................................... 3-1 In Windows XP................................................................................................................................ 3-1 In Windows 2000............................................................................................................................ 3-5 In Windows Me................................................................................................................................ 3-7 In Windows 98 SE........................................................................................................................... 3-9

Using the USB port....................................................................................................................... 3-12 4 Configuring your DSL Router Understanding DSL Router configurations........................................................................................ 4-1 Connecting to your DSL Router’s Home Page ............................................................................... 4-1 Configuring your DSL Router................................................................................................................ 4-3 PPPoA/PPPoE Configuration........................................................................................................ 4-3 RFC 1483 Routed IP Configuration.......................................................................................... 4-5 RFC 1483 Bridged IP Configuration.......................................................................................... 4-7 Disabling the Proxy Server..................................................................................................................... 4-8 Using Internet Explorer................................................................................................................. 4-9 Disconnecting from the Internet........................................................................................................ 4-10 In PPPoA and PPPoE Mode........................................................................................................ 4-10 In RFC 1483 Routed and Bridged Mode................................................................................ 4-10 Checking your DSL Router’s Status.................................................................................................. 4-10 Restoring Factory Default Settings..................................................................................................... 4-11 5 Configuring Advanced Features LAN Settings............................................................................................................................................... 5-1 DHCP Server Settings.............................................................................................................................. 5-1 LAN Client................................................................................................................................................... 5-2 Diagnostic Tests......................................................................................................................................... 5-3 Loopback Test.................................................................................................................................. 5-3 Ping Test............................................................................................................................................. 5-3 DMZ Settings.............................................................................................................................................. 5-4 Port Forwarding......................................................................................................................................... 5-5 Universal Plug and Plug............................................................................................................................ 5-5 Filtering.......................................................................................................................................................... 5-6

MAC Address Filtering .................................................................................................................. 5-7 Change Password...................................................................................................................................... 5-8 Restore Factory Default Settings.......................................................................................................... 5-8 Firmware Upgrade.................................................................................................................................... 5-9 Appendixes A Technical Specifications B Troubleshooting Connection to your DSL Router’s home page................................................................................ B-1 Connection to the Internet.................................................................................................................... B-2 LED Status.................................................................................................................................................... B-3 Normal Setup Status....................................................................................................................... B-3 Difficulties In Windows XP.................................................................................................................... B-5 C Frequently Asked Questions D Glossary

Developed with the most advanced Digital Subscriber Line (DSL) today, the DSL Router provides you with high-speed broadband Internet connection using an existing phone line. Enjoy speedy file transfers, watch Internet movies, video- conference, and view videos without any long waits. You can also surf the Internet and make a phone call at the same time! Your DSL Router can be connected to your computer using a USB or Ethernet port. Compliant with both ITU G.Lite and G.DMT, your DSL Router is capable of Asymmetric Digital Subscriber Line (ADSL) full-rate operation up to 12 Mbps downstream and 1 Mbps upstream, depending on your subscription with your Internet Service Provider (ISP). Your DSL Router is also capable of transmitting data at a higher rate using the latest ADSL technology – ADSL2 and ADSL2+. ADSL2 can achieve downstream data rate of up to 12Mbps, and ADSL2+ can achieve downstream data rate of up to 20Mbps (requires ISP with complementary infrastructure to support these standards). DSL Router information Before you begin, write down your DSL Router’s model and serial numbers found at the bottom of your DSL Router. Package Contents ❑Creative Broadband Blaster DSL Router 8015U ❑USB cable ❑Straight Ethernet cable ❑RJ-11 phone cable ❑Power adapter ❑Installation CD ❑Quick Start Leaflet

meets the following minimum system requirements: Using Ethernet connection ❑Installed Network Interface Card (NIC) ❑CD-ROM drive for software installation ❑Microsoft® Internet Explorer version 6.0 Using USB connection ❑Intel® Pentium® II 300 MHz or equivalent processor ❑Microsoft Windows® XP, 2000, Me (Millennium Edition) or 98 SE (Second Edition) ❑20 MB of free hard disk space ❑32 MB RAM ❑USB port ❑CD-ROM drive for software installation ❑Microsoft Internet Explorer version 6.0 You will need a hub if you wish to connect more than 2 computers to your DSL Router. Depending on your computer’s configurations, you can choose to install your router using the Ethernet or USB port.

❍Tip. This tells you about shortcuts or hints relating to a feature. ❍Note. This highlights additional or important information about a feature. ❍Caution! This highlights proper usage of your device. Use this information to avoid situations involving risk. ❍Warning! This warns you of possible hazards to yourself or your device, which may result in injury or damage.

About your DSL Router This manual will guide you through the process of setting up your DSL Router. Place your DSL Router in front of you as you go through this section to help you to identify the various components of your modem. LED Indication POWER LED lights up when your DSL Router is connected to a power source. READY LED flashes when your DSL Router is initializing the DSL connection. LED lights up when DSL connection is ready. LINK LED lights up when the Ethernet or USB port is connected to your computer. ACTIVITY LED flashes when there is data transfer to or from the Internet. Figure 1-1: Front view of your DSL Router Ready LED Activity LED Link LED Power LED

Port/Connector Indication PHONE PORT Connects to the telephone via a microfilter. DSL LINE PORT Connects to the telephone wall outlet using the provided RJ-11 phone cable. ETHERNET PORT Connects to the Ethernet port on your computer using the Straight Ethernet cable. If you are connecting your DSL Router using the Ethernet port, do not connect the USB port on the same computer. USB PORT Connects to the USB port on your computer using the USB cable. If you are connecting your DSL Router using the USB port, do not connect the Ethernet port on the same computer. RESET BUTTON Resets your DSL Router’s settings to the factory default settings. POWER CONNECTOR Connects to the power outlet using the provided power adapter. Figure 1-2: Back view of your DSL Router DSL LINE port Ethernet port Reset button Power connector USB port Phone port

Setting up your DSL Router using Ethernet connection Depending on your computer’s configurations, you can choose to install your DSL Router using the Ethernet or USB port on the same computer. Do not install your DSL Router using both connections on the same computer. If you are connecting your DSL Router using the USB port, skip this chapter and go to "Setting up your DSL Router using USB connection" on page 3-1.

Setting up your DSL Router Using the Ethernet port Before setting up your DSL Router, be sure that the Network Interface Card in your computer is installed and functioning properly. Use Figure 2-1 as a reference when following these instructions to set up your DSL Router. 1. Connect the straight Ethernet cable to the Ethernet ports on your computer and DSL Router. 2. Locate a telephone wall outlet and unplug any telephone cable that is connected to it. DO NOT use the USB port on your DSL Router if you are using the Ethernet port on the same computer. If you want more than 2 computers to have access to your DSL Router through a hub, you may need to use a crossed Ethernet cable to connect your DSL Router to the hub. Consult your hub’s manual for details. Figure 2-1: Setting up your DSL Router using the Ethernet port Telephone wall outlet RJ-11 cables Power adapter Ethernet port Ethernet port Straight Ethernet cable DSL LINE port Power connector Phone Port Reset button USB port Microfilter

3. Connect one end of the RJ-11 phone cable provided into the telephone wall outlet. 4. Connect the other end into the DSL LINE port of your DSL Router. 5. Connect the small round plug of the power adapter provided to the DSL Router’s power connector and plug your power adapter into a power outlet. 6. Turn on the power supply. 7. If you have telephones and fax machines sharing the same phone line, connect them to the telephone wall outlet or your DSL Router phone port with microfilters as shown below. The microfilters will help to ensure voice and data quality. Figure 2-2: Connecting a telephone to the telephone wall outlet Telephone Wall outlet RJ-11 phone cable Microfilter Telephone

Configuring your Network Interface Card Before using your DSL Router, you need to configure your Network Interface Card. In Windows XP/ Windows 2000 1. After setting up your DSL Router, turn on your computer. 2. In Windows XP, click Start -> Settings -> Control Panel and double-click the Network Connections icon. In Windows 2000, click Start -> Control Panel and double click the Network and Dial Up Connections icon. 3. When the window similar to Figure 2-3 appears, right-click the Local Area Connection icon, and then click Properties. If you are connecting your DSL Router using the USB port, skip this chapter and go to "Setting up your DSL Router using USB connection" on page 3-1. Figure 2-3

4. When the dialog box similar to Figure 2-4 appears, be sure that the name of your network card is displayed in the first box. 5. In the list below the box, click the Internet Protocol (TCP/IP) check box to select it. 6. Click the Properties button. Figure 2-4

7. When the dialog box similar to Figure 2-5 appears, click Obtain an IP address automatically option, and then click the OK button. 8. When the Local Area Connection Properties dialog box appears, click the OK button. Before using your DSL Router, you will need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1. Figure 2-5

In Windows Me/ Windows 98 SE 1. After setting up your DSL Router, turn on your computer. 2. Click Start -> Settings -> Control Panel. 3. When the dialog box similar to Figure 2-6 appears, double-click the Network icon. Figure 2-6

4. When the dialog box similar to Figure 2-7 appears, click the Configuration tab. 5. Click the adapter that has the name of your Ethernet card, for example, TCP/IP->Intel 8255x-based PCI Ethernet Adapter (10/100). 6. Click the Properties button. Figure 2-7

7. When the dialog box similar to Figure 2-8 appears, click the IP Address tab. 8. Click the Obtain an IP address automatically option, and then click the OK button. 9. In the Network window, click the OK button. 10. Restart your computer to let the changes take effect. Before using your DSL Router, you will need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1. Figure 2-8

Setting up your DSL Router using USB connection Depending on your computer’s configurations, you can choose to install your DSL Router using the Ethernet or USB port on the same computer. Do not install your DSL Router using both connections on the same computer. Installing the USB Driver Before using your DSL Router, you need to install the USB driver. Do not connect the USB cable to the USB ports on your computer and DSL Router before installing the USB drivers. In Windows XP 1. Insert the Installation CD into your CD-ROM drive. The disc supports Windows Autoplay mode and starts running automatically. If the Autoplay window appears, select the applications that you want to install, and then click the OK button. 2. Follow the onscreen instructions. 3. When prompted, restart your computer. If you are connecting your DSL Router using the Ethernet port, skip this chapter and go to "Setting up your DSL Router using Ethernet connection" on page 2-1. If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 6 to install the USB drivers.

4. When the Installshield Wizard dialog box (Figure 3-1) appears, click the Next button. 5. When the dialog box similar to Figure 3-2 appears, click the Install button. Figure 3-1 Figure 3-2

6. If the dialog box similar to Figure 3-3 appears, click the Continue Anyway button. For more information, refer to "Difficulties In Windows XP" on page B-5. 7. Click the Finish button. 8. Connect the USB cable to the USB ports on your computer and DSL Router. See "Setting up your DSL Router" on page 3- 12. 9. Click the Install the software automatically (Recommended) option and click the Next button (Figure 3- 4). Figure 3-3 Figure 3-4

10. If the dialog box similar to Figure 3-5 appears, click the Continue Anyway button. For more information, refer to "Difficulties In Windows XP" on page B-5. 11. Click the Finish button (Figure 3- 6). Before using your DSL Router, you will need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1. Figure 3-5 Figure 3-6

In Windows 2000 1. Insert the Installation CD into your CD-ROM drive. The disc supports Windows Autoplay mode and starts running automatically. If the Autoplay window appears, select the applications that you want to install, and then click the OK button. 2. Follow the onscreen instructions. 3. When prompted, restart your computer. 4. When the Installshield Wizard dialog box (Figure 3-7) appears, click the Next button. If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 6 to install the USB drivers. Figure 3-7

5. When the dialog box similar to Figure 3-8 appears, click the Install button. 6. If the Digital Signature Not Found dialog box (Figure 3-9) appears, click the Yes button. 7. Click the Finish button. 8. Connect the USB cable to the USB ports on your computer and DSL Router. See "Setting up your DSL Router" on page 3-12. Figure 3-8 Figure 3-9

9. If the Digital Signature Not Found dialog box (Figure 3-10) appears, click the Yes button. Before using your DSL Router, you will need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1. In Windows Me 1. Insert the Installation CD into your CD-ROM drive. The disc supports Windows Autoplay mode and starts running automatically. If the Autoplay window appears, select the applications that you want to install, and then click the OK button. 2. When prompted, restart your computer. Figure 3-10 If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 5 to install the USB drivers.

3. When the Installshield Wizard dialog box (Figure 3-11) appears, click the Next button. 4. When the dialog box similar to Figure 3-12 appears, click the Install button. 5. Click the Finish button to restart the system if prompted. 6. Connect the USB cable to the USB ports on your computer and DSL Router. See "Setting up your DSL Router" on page 3-12. Before using your DSL Router, you will need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1. Figure 3-11 Figure 3-12

In Windows 98 SE 1. Insert the Installation CD into your CD-ROM drive. The disc supports Windows Autoplay mode and starts running automatically. If the Autoplay window appears, select the applications that you want to install, and then click the OK button. 2. Follow the onscreen instructions. 3. When prompted, restart your computer. 4. When the Installshield Wizard dialog box (Figure 3-13) appears, click the Next button. Windows 98 users may be prompted to insert the Windows 98 installation CD into the CD-ROM drive during installation. If you want to install the applications later, from the Autoplay window, click the Exit button and proceed to step 6 to install the USB drivers. Figure 3-13

5. When the dialog box similar to Figure 3-14 appears, click the Next button. 6. When the dialog box similar to Figure 3-15 appears, click the Install button. Figure 3-14 Figure 3-15

7. When the dialog box similar to Figure 3- 16 appears, click the Finish button to restart the system. 8. Connect the USB cable to the USB ports on your computer and DSL Router. See "Setting up your DSL Router" on page 3- 12. Before using your DSL Router, you will need to configure your DSL Router. See "Configuring your DSL Router" on page 4-1. Figure 3-16

Setting up your DSL Router Using the USB port Use Figure 3-17 as a reference when following these instructions to set up your DSL Router. 1. Do not connect the USB cable to the USB ports on your computer and DSL Router until after you have installed the USB drivers. 2. Locate a telephone wall outlet and unplug any telephone cable that is connected to it. DO NOT use the Ethernet port on your DSL Router if you are using the USB port on the same computer. Figure 3-17: Setting up your DSL Router using the USB port USB port USB cable Telephone Wall outlet Power adapter Ethernet port DSL LINE port Power connector Reset button USB port RJ-11 cables Phone port Microfilter

3. Connect one end of the RJ-11 phone cable provided into the telephone wall outlet. 4. Connect the other end into the DSL LINE port of your DSL Router. 5. Connect the small round plug of the power adapter provided to the DSL Router’s power connector and plug your power adapter into a power outlet. 6. Turn on the power supply. 7. If you have telephones and fax machines sharing the same phone line, connect them to the telephone wall outlet or your DSL Router phone port with microfilters as shown below. The microfilters will help to ensure voice and data quality. Figure 3-18: Connecting a telephone to the telephone wall outlet Telephone Wall outlet RJ-11 phone cable Microfilter Telephone

Configuring your DSL Router Understanding DSL Router configurations Your DSL Router can be configured in several ways. Consult your Internet Service Provider for the configuration that best suits you. You need to configure your DSL Router just once, unless your Internet Service Provider changes the configuration settings. Your DSL Router supports the following configurations: ❑PPPoA LLC/PPPoA VC-Mux/PPPoE LLC — this requires a User ID and Password for authentication. See "PPPoA/PPPoE Configuration" on page 4-3. ❑RFC 1483 Routed IP — the Internet Protocol (IP) address used can be static or dynamic depending on your ISP provider.. See "RFC 1483 Routed IP Configuration" on page 4-5. ❑RFC 1483 Bridged IP — the Internet Protocol (IP) address used can be static or dynamic depending on your ISP provider. See "RFC 1483 Bridged IP Configuration" on page 4-7. Connecting to your DSL Router’s Home Page Before proceeding, make sure that you have configured your Network Interface Card (see "Configuring your Network Interface Card" on page 2-4) or installed the USB device drivers successfully (see "Installing the USB Driver" on page 3-1). You need to connect to your DSL Router’s home page to configure your DSL Router. Disable any proxy server in use before accessing the DSL Router home page. See "Disabling the Proxy Server" on page 4-8.

1. If your DSL Router is connected using the Ethernet or USB port, the Link LED will light up. 2. Start Internet Explorer. 3. In the Address box, type http:// 192.168.1.1. 4. Press the Enter key on your keyboard. 5. In the dialog box similar to Figure 4- 1 appears, type admin in the User name box and admin in the Password box. 6. Click the Submit button. Figure 4-1

Configuring your DSL Router PPPoA/PPPoE Configuration 1. After connecting to your DSL Router’s home page, move your mouse over Configuration on the left pane and select WAN Settings. 2. When the window similar to Figure 4-2 appears, select PPPoA or PPPoE in the encapsulation mode. 3. Type in the VPI and VCI values provided by your Internet Service Provider in their respective boxes. 4. Click the Next button. Figure 4-2 If your DSL connection is charged on the basis of time online, turn off your DSL Router when it is not in use, to avoid unnecessary charges.

5. When the window similar to Figure 4-3 appears, type in the user name and password provided by your DSL service provider. 6. Click the Next button. 7. When the window similar to Figure 4-4 appears, check that all settings are correct. Click the Finish button. Figure 4-3 Figure 4-4

8. When the window similar to Figure 4-5 appears, click the OK button. 9. Wait for your DSL Router to connect to the Internet. You can now start surfing the Internet at high speed! RFC 1483 Routed IP Configuration 1. After connecting to your DSL Router’s home page, click Configuration on the left pane and select WAN Settings. 2. When the web page similar to Figure 4-6 appears, select RFC 1483 Routed in Encapsulation Mode. 3. Type in the VPI and VCI values provided by your Internet Service Provider in their respective boxes. 4. Click the Next button. The web page similar to Figure 4-7 appears. Figure 4-5 Figure 4-6

5. Click the WAN DHCP Client option if your ISP provider provides you with a Dynamic WAN IP address. Click the Next button and proceed to step 7. Do not click the WAN DHCP Client option if your ISP provider provides you with a Static WAN IP address. Click the Next button. 6. When the WAN Settings web page (Figure 4-8) appears, type in the WAN IP address, subnet mask, gateway and DNS IP address values provided by your ISP in their respective boxes. Click the Next button. 7. Click the Finish button. 8. Click the OK button. 9. Wait for your DSL Router to connect to the Internet. You can now start surfing the Internet at high speed! Figure 4-7 If you are using a Static WAN IP address, you must configure the WAN IP address, subnet mask, gateway and DNS IP address. Figure 4-8 If your DSL connection is charged on the basis of time online, turn off your DSL Router when it is not in use, to avoid unnecessary charges. DO NOT turn off the computer or DSL Router when the DSL Router configuration is being saved.

RFC 1483 Bridged IP Configuration 1. After connecting to your DSL Router’s home page, click Configuration on the left pane and select WAN Settings. 2. When the window similar to Figure 4-9 appears, select Bridge in Encapsulation Mode. 3. Type in the VPI and VCI values provided by your Internet Service Provider in their respective boxes. 4. Click the Next button. 5. In the web page that appears (Figure 4-10), click the Next button. Figure 4-9 DO NOT turn off the computer or DSL Router when your DSL router is restarting. Figure 4-10 If your DSL connection is charged on the basis of time online, turn off your DSL Router when it is not in use, to avoid unnecessary charges.

6. In the web page that appears (Figure 4-11), click the Finish button. 7. Click the OK button. 8. Wait for your DSL Router to connect to the Internet. You can now start surfing the Internet at high speed! Disabling the Proxy Server You need to disable any proxy server in use before accessing the DSL Router home page. Figure 4-11

Using Internet Explorer 1. Start Internet Explorer. 2. From the Tools menu, click Internet Options. 3. When the dialog box similar to Figure 4-12 appears, click the Connections tab. 4. Click the Never dial a connection option to select it and click the LAN Settings button. 5. When the Local Area Network (LAN) Settings dialog box similar to Figure 4-13 appears, make sure that the Automatically detect settings, Use automatic configuration script and Use a proxy server check boxes are not selected, and then click the OK button. 6. In the next dialog box that appears, click the OK button. Figure 4-12 Figure 4-13

Disconnecting from the Internet When you reconnect your DSL Router to the Internet, always make sure that you turn on your DSL Router before you turn on your computer. Wait at least 30 - 60 seconds for your DSL Router to connect to the Internet. In PPPoA and PPPoE Mode If you are using PPPoA or PPPoE configurations for your DSL router, you can disconnect from the Internet by turning off the main power supply to your DSL Router. Alternatively, you can disconnect from the Internet through your DSL Router’s home page: 1. Click Status on the left pane and select Connection. 2. Click the Disconnect button on the right pane. 3. To reconnect to the Internet, click the Connect button. In RFC 1483 Routed and Bridged Mode If you have chosen RFC 1483 Routed or Bridged mode for your DSL Router, you can disconnect from the Internet by turning off the main power supply to your DSL Router. Checking your DSL Router’s Status The DSL Router web page allows you to view your DSL Router’s status, such as your DSL Line status, PPP Connection status and WAN status. On the left pane, place your cursor over the Status link to select the statistic you want to view. The DSL Router web page also enables you to perform the following tasks: Diagnostic Test (Loopback test and Ping test), Firmware Upgrade, Reboot Modem and Log Out. On the left pane, click the link of the task you want to perform.

Restoring Factory Default Settings To reset your DSL Router to the factory default settings 1. Make sure your DSL Router is turned on. 2. Push the end of a thin object (for example, a straightened paperclip) into the Reset hole, and hold for approximately 10 seconds until all the LEDs light up. You can also reset your DSL Router using your web browser. For more information, see "Restore Factory Default Settings" on page 5-8

Configuring Advanced Features This chapter tells you how to configure your DSL Router’s advanced settings. LAN Settings This allows you to change your DSL Router’s IP address. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> LAN Settings -> LAN IP. 3. When the web page similar to Figure 5- 1 appears, type your LAN IP Address and Subnet Mask in the respective boxes. 4. Click the Save button. DHCP Server Settings Dynamic Host Configuration Protocol (DHCP) is a method of assigning a temporary IP address to a host, such as a computer, connected on a specific network. With dynamic addressing, a particular host may have a different IP address each time it connects to the network. Figure 5-1

1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> LAN Settings -> DHCP Server Settings. 3. When the web page similar to Figure 5- 2 appears, select your DHCP configuration. 4. Click the Next button. 5. Type the DHCP server start and end IP Address, and lease time for the pool of IP Addresses defined. 6. Click the Submit button. 7. Click the OK button. 8. Wait for your DSL Router to restart. LAN Client The feature allows you to add LAN clients. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> Advanced Settings -> LAN Client. 3. When the web page similar to Figure 5- 3 appears, type in the LAN Client Name and IP address. 4. Select the check box under Selected. 5. Click the Add button. 6. Click the OK button. 7. Wait for your DSL Router to restart. Figure 5-2 Figure 5-3

Diagnostic Tests Loopback Test This feature allows you to test the physical connection between your DSL Router and ISP. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Diagnostic Test -> Loopback Test. 3. When the web page similar to Figure 5- 4 appears, click the Begin button. Ping Test This feature allows you to check if an IP Address exists. Figure 5-4

1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Diagnostic Test -> Ping Test. 3. When a web page similar to Figure 5-5 appears, type your IP Address. 4. Click the Begin button. DMZ Settings Demilitarized Zone (DMZ) is a computer host or small network inserted as a "neutral zone" between a company's private network and the outside public network. It allows access from the Internet to the host computer. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> Advanced Settings -> DMZ. 3. When a web page similar to Figure 5-6 appears, click the Enable DMZ box. 4. In the DMZ IP Address Setting box, type the IP Address of the local server’s computer. 5. Click the Submit button. 6. Click the OK button. 7. Wait for your DSL Router to restart. Figure 5-5 Enabling DMZ will allow access from the Internet to your LAN and may compromise on your security. Figure 5-6

Port Forwarding Port forwarding, also known as port mapping, allows you to direct TCP/UDP ports to computers on your LAN. This allows access from the Internet to your LAN. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> Advanced Settings -> Port Forwarding. 3. When a web page similar to Figure 5-7 appears, select the check box. Type the port number that you want to forward in the Start Port Number and End Port Number (optional) boxes. 4. Select the type of port that you want to forward, for example, the TCP, UDP option. 5. In the IP Address box, type the IP Address of the local computer you want to forward the port to, and then click the Add button. 6. Click the OK button. 7. To forward more ports, repeat steps 2 to 5. 8. Wait for your DSL Router to restart. Universal Plug and Plug Universal Plug and Play (UPnP) allows your DSL Router to be automatically detected when it is connected to a network. Enabling port forwarding will allow access from the Internet to your LAN and may compromise on your security. Figure 5-7

1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> Advanced Settings -> UPnP. 3. When a web page similar to Figure 5-8 appears, select the Enable UPnP check box. 4. Click the Submit button. 5. Click the OK button. Filtering IP Address Filtering IP Address Filter allows you to filter out specified IP addresses. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> Advanced Settings -> Filtering -> IP Address Filter. 3. When a web page similar to Figure 5-9 appears, type the LAN Client Name and IP Address that you want to filter. 4. Select the Filtered check box. 5. Click the Submit button. 6. Click the OK button. 7. Wait for your DSL Router to restart. Figure 5-8 Figure 5-9

MAC Address Filtering Media Access Control (MAC) filtering is used to block data transfer on your LAN. The MAC address of a Network Interface device is a 12 digit hexadecimal number that is unique. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> Advanced Settings -> Filtering -> MAC Address Filter. 3. When a web page similar to Figure 5-10 appears, select the Selected check box. 4. In the Source MAC and/or Destination MAC box, type the MAC Address of the Network Interface card. 5. Select Protocol and Mode settings. 6. Click the Add button. 7. Click the OK button. 8. Wait for your DSL Router to restart. Figure 5-10

Change Password 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Configuration -> Advanced Settings -> Change Password. 3. When a web page similar to Figure 5-11 appears, type in your new password, and then click the Submit button. 4. Click the OK button. 5. Wait for your DSL Router to restart. Restore Factory Default Settings This feature allows you to restore your DSL router’s settings to the factory default settings. 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click Restore Factory. 3. When a web page similar to Figure 5-12 appears, click the OK button. Figure 5-11 You can also reset your DSL Router using the Reset hole. For more information, see "Restoring Factory Default Settings" on page 4-11. Figure 5-12

Firmware Upgrade To upgrade your DSL Router firmware, do the following: 1. Connect to your DSL Router’s home page. See "Connecting to your DSL Router’s Home Page" on page 4-1. 2. Click the Firmware Upgrade link on the left pane. 3. When a web page similar to Figure 5-13 appears, click the Browse button. 4. Select the firmware upgrade file. 5. Click the OK button. Figure 5-13

Technical Specifications This section provides certain technical specifications for your Creative Broadband Blaster DSL Router 8015U. Data Encapsulation Protocol ❑RFC 2684/1483 Bridge/Routed, PPPoA LLC/VC MUX, PPPoE LLC ADSL Line Interface ❑ANSI T1.413 issue 2 ❑ITU-T G.992.1 (G.DMT) ❑ITU-T G.992.2 (G.LITE) ❑ITU-T G.992.3 (ADSL 2) ❑ITU-T G.992.5 (ADSL 2+) Electrical ❑Power adapter with output 16 V AC, 750 mA Interface ❑Ethernet 10/100 Base-T (LAN). MDI-X ❑RJ-11 (WAN) ❑USB 2.0 Full Speed Dimensions ❑Length: 145 mm / Width: 125 mm / Height: 30 mm Compliance ❑IEC 60950 ❑CE EN55022 ❑CE EN55024 ❑CB ❑FCC Part 15B ❑FCC Part 68 ❑UL

self-help tool "Knowledge Base" for online troubleshooting and solutions. Go to www.creative.com and select your region. Connection to your DSL Router’s home page The Web browser does not connect to the DSL Router home page. You are not using the correct IP address. Try the following: ❑Be sure that you have typed the default IP address as 192.168.1.1. ❑Check your network device’s IP address: In Windows XP/2000: 1. Click Start -> Programs/All Programs -> Accessories -> Command Prompt. 2. In the window that appears, type ipconfig/release, and then press the Enter key. 3. Type ipconfig/renew, and then press the Enter key. 4. Be sure that the IP Address is 192.168.1.x. x may be any number between 2 and 254. In Windows Me/98 SE: 1. Click Start -> Run. 2. In the window that appears, type winipcfg, and then click the OK button. 3. Under Ethernet Adapter Information, click your network adapter. 4. Click the Release button, and then click the Renew button. 5. Be sure that the IP Address is 192.168.1.x. x may be any number between 2 and 254.

You did not set up your DSL Router correctly. Try the following: ❑Be sure that if your DSL Router is connected to your computer through a hub, you are using a crossed Ethernet cable. Also, be sure that you have configured your DSL Router correctly. For more information, see "Configuring your DSL Router" on page 4-1. ❑If your computer is connected to your DSL Router using a USB cable, be sure that you have installed the USB driver. ❑Be sure that the power adapter is plugged in securely and the power is turned on. ❑Be sure that the phone line from the telephone wall outlet is connected securely to the LINE connector of your DSL Router. ❑Be sure that you have subscribed with a Internet Service Provider. ❑Be sure that the Ready LED is turned on. ❑If you are required to specify your WAN IP address, be sure that you have typed the values for IP address, Subnet Mask, Gateway and DNS Server provided by your Internet Service Provider correctly.

Normal Setup Status When your DSL Router is turned on, all the LED lights up. After several seconds, all the LEDs will go into their correct states. See "About your DSL Router" on page 1- 1 for more information. The Power LED on my DSL Router does not turn on. Your DSL Router is not properly powered by an external power source. Try the following: ❑Check both ends of the DC adapter cable connection to see if the connectors are firmly plugged into both the telephone wall outlet and your DSL Router. ❑Be sure that you have turned on the power outlet connected to your DSL Router. ❑Be sure that you are using the power adapter provided. The Link LED on my DSL Router does not turn on after I connect my DSL Router and computer with the Straight Ethernet cable. Your DSL Router is not properly connected to your computer. Try the following: ❑Check both ends of the Straight Ethernet cable and be sure that they are plugged in securely. ❑Be sure that you have used a Straight Ethernet cable. However, if you are connecting to more than 2 computers through a hub, you may need to use a crossed Ethernet cable to connect your DSL Router to your hub. ❑Be sure that you have configured your Network Interface Card correctly. The Link LED on my DSL Router is turned on and is unable to access the Internet. Your DSL Router may not be properly configured. See topic "My DSL Router does not connect to the Internet." on page B-2.

There is no DSL service subscription. There is too much noise on your telephone line. Your Internet Service Provider may be experiencing problems. Check on the following: ❑Be sure that the telephone cable is connected correctly to your DSL Router. ❑Try connecting again after a few minutes as external interference can cause disruptions to your DSL line. ❑Attach microfilters to all phone jacks connected to analog devices sharing the same line as your DSL connection. Examples of analog devices include telephones, analog modems and fax machines. ❑Be sure that you have a subscription with a Internet Service Provider. ❑Check with your Internet Service Provider.

operating system when a driver is being installed. At the time of this product's release, Microsoft strongly encouraged companies to submit their hardware solutions for certification. If a hardware device driver is not submitted, or does not qualify, for Microsoft certification, a warning message similar to the one below appears. You may see this message when installing this driver or update. If you do, you may choose to click the Continue Anyway button. Creative has tested this driver on Windows XP, and it does not impair or destablize your computer.

Frequently Asked Questions Can my DSL Router work with Operating Systems other than Windows? Yes, if you are connecting your DSL Router using the Ethernet port. Ethernet port connection is operating system independant. Currently, Technical Support only provides support for Windows-based operating systems. If you are, however, connecting your DSL Router using the USB port, your DSL Router will only work with Windows XP, Windows 2000, Windows Me and Windows 98 SE. How can I check whether I have either Static or DHCP IP addressing? Consult your DSL Service Provider. Which Ethernet card is compatible with my DSL Router? Your DSL Router is compatible with virtually any Network Interface Card. Which protocol does my DSL Router support? Currently, TCP/IP is the only protocol standard for the Internet and has become the global standard for communications.

terminologies. ADSL Asymmetric Digital Subscriber Line — A Digital Subscriber Line (DSL) technology that allows digital data to be sent over existing telephone lines. Though many different DSL technologies have been developed, ADSL is the most popular among individuals and small businesses because it offers higher downstream (or download) than upstream (or upload) data rates. Bridge A hardware device that links two or more LANs and manages the transfer of data between these LANs. The two networks being connected can be alike or dissimilar. Broadband A transmission media that can handle the transmission of multiple messages, at different frequencies, at one time. Broadband signals use analog carriers. DHCP Dynamic Host Configuration Protocol — A method of assigning a temporary IP address to a host, such as a computer, connected to a specific network. With dynamic addressing, a particular host has a different IP address each time it connects to the network. DNS Domain Name System — This allows you to specify a symbolic name, a meaningful and easy-to-remember “handle,” instead of an IP address. The DNS is the way that Internet domain names are located and translated into Internet Protocol addresses. Downstream Data transferred from the telecommunication network to the customer’s premises.

into high-speed digital lines for fast Internet access. This technology uses a digital coding technique to get large capacity out of existing phone lines without interfering with regular services — one can use the phone and surf the Internet at the same time. In this way, DSL provides simultaneous Internet and voice/fax capabilities over a single telephone line without any interference. Ethernet A local-area network (LAN) protocol that supports data transfer rates of 10 Mbps. It is one of the most widely implemented LAN standards that operates using the twisted pair or coaxial cable. A version of Ethernet, called 100 Base-T (or fast Ethernet), supports data transfer rates of 100 Mbps. G.dmt An industry standard known as G.992.1, which refers to ADSL technology that uses DMT modulation and that does not require a splitter box to be installed at the user’s premises. This technology supports downstream data rates of up to 8 megabits per second and upstream data rates of up to 960 kilobits per second. G.Lite A “splitterless” ADSL technology that uses CAP or DMT modulation, and supports downstream data rates of up to 1.5 megabits per second and upstream data rates of up to 384 kilobits per second. Hub A device used for connecting nodes in a star topology, that is, all the nodes are connected to a central hub. A passive hub simply organizes the wiring, while an active hub also regenerates and retransmits signals. Internet The world’s largest computer network, which links computers and networks that communicate via the standard TCP/IP protocol.

particular machine on a network. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be 0 to 255, for example, 11.160.10.240 is an IP address. Any machine connected to the Internet is assigned an IP address. ISP Internet Service Provider — An organization that provides Internet access to computer users. LAN Local Area Network — A computer network that spans a relatively small area. Most LANs are confined to an office, single building, or group of buildings. Mbps Megabits per second — A measure of data transfer speed. NIC Network Interface Card — A card that is installed in a computer so that it can be connected to a network. The NIC manages the flow of network information to and from the computer. Packet A unit of information, which is data of a fixed length, sent as a whole from one device to another on a network. It contains a header with a destination address and control information, and a payload that has the user data. PING ’Packet Internet Groper — An Internet program used to determine whether a specific IP address is accessible. It works by sending a packet to the specified address and waiting for a reply. PING is used primarily to troubleshoot network connections. PPP Point-to-Point Protocol — A communication protocol that allows a computer to be connected to the Internet. Protocol A set of agreed-upon rules for transmitting data between two devices. A computer must support the right protocols in order to communicate with other computers.

“interoperability”. RJ-11 A connector/socket for two pairs (four wires) of twisted pair cables that is used primarily to connect telephone equipment. Router A hardware device connecting two separately functional networks that use the same or different protocols. Routers look at the destination addresses on data packets, and then decide which route to send them on. Subnet Mask A 32-bit string of a TCP/IP address — one part of which is the network address and another part of which is the host address. A Subnet Mask is usually represented in dotted-decimal notation, for example, 255.255.255.0. TCP/IP Transmission Control Protocol/Internet Protocol. A suite of communication protocols that is used by computers or networking devices on the Internet so that they can communicate with each other. TCP/IP uses several protocols, the two main being TCP and IP. VPI Virtual Path Identifier — A numerical value assigned by your Internet Service Provider to your DSL device to ensure proper connection with the DSL equipment at the telephone company’s office. VCI Virtual Channel Identifier — A numerical value assigned by your Internet Service Provider to your DSL device. VCI goes hand in hand with VPI to ensure connection with your Internet Service Provider’s equipment. WAN Wide Area Network — A computer network that spans a relatively large geographical area. Typically, a WAN consists of two or more LANs.