North Invent Wave PERFORMANCE Operation & User’s Manual

this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. Wave PERFORMANCE Monitors (PPCs) NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com November 2021 Please note that the content of this document is subject to continuous revision. USER'S MANUAL

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 2 Table of Contents 1. Terms and Abbreviations .............................................................................................................. 3 2. Panel PC Description .................................................................................................................... 4 3. Product Identification .................................................................................................................... 5 4. Packaging and Delivery ................................................................................................................ 5 5. Mechanical Dimensions ................................................................................................................ 5 6. Compass Safe-distance:................................................................................................................. 5 7. Electrical Installation..................................................................................................................... 6 7.1. Pin-Assignments............................................................................................................................ 6 8. Operating System (OS) ............................................................................................................... 10 9. Color calibration and use in ECDIS applications........................................................................ 10 10. Simple Network Management Protocol (SNMP)........................................................................ 11 11. System Utility and API ............................................................................................................... 13 12. Technical Specifications ............................................................................................................. 13 13. Troubleshooting .......................................................................................................................... 14 14. Cleaning ...................................................................................................................................... 14 15. Maintenance and Service ............................................................................................................ 14 16. Update ......................................................................................................................................... 14

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 3 Foreword Thank you for purchasing a North Invent Wave PERFORMANCE Monitor (Panel PC). Our series of rugged Monitors and Panel PCs are developed and built with the greatest care and state of the art electronic and software features. North Invent focuses its full expertise in offering dedicated display solutions, matching with your highest requirements and use. Before starting to operate the Panel PC, we would like to suggest that you carefully read through the present document, as our aim with this User’s Manuel is to give you the best experience in using your device. May you have any suggestions for improvements, or any feedbacks about this manual, the Panel PC and/or its features, feel free to contact us. We will be pleased to oblige. This User’s Manual is for use only with our Wave PERFORMANCE Monitors (Panel PCs). To assess which series of Monitor or Panel PC you are in possession of, please check the Serial Number plate at the back of the device. May you have a different series of Monitor or Panel PC, please contact us, so to have the proper manual sent to your attention. 1. Terms and Abbreviations DIU Display Unit DP DisplayPort ELU Electronics Unit HMI Human- Machine Interface LCD Liquid Crystal Display LED Light-Emitting Diode OS Operating System PPC Panel PC RGB Red-Green-Blue SNMP Simple Network Management Protocol

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 4 2. Panel PC Description The Wave PERFORMANCE Monitors are a series of rugged TFT LCD Display Panel PCs available in 18.5", 19", 21.5", 24", 27" and 32" display sizes and with Intel Core i3/i5/i7 and Celeron CPUs. All our Panel PCs are built following a modular approach and can be console mounted or equipped with a stand (hinge). Each Panel PC is constituted by the following set of components: Display Unit (DIU) - Front end of the Panel PC consisting of the glass (optionally: touch) and display panel in the aluminum frame. Electronics Unit (ELU) - Back end of the Panel PC consisting mainly of power supply, motherboard, SSD, and memory. DIU and ELU are modular and easily separable to ensure efficient configuration, maintenance, and repair. Optional accessories are a hinge (tiltable stand), panel mounting kits and HMI units (operator panels). Each Panel PC presents the following materials and features: The Front, Display Frame and Cover are made of Marine Grade Aluminum allowing to reduce weight while eliminating corrosion problems. The electronics include a specifically designed Power Supply, a high-quality Display Controller, a Backlight LED driver, and a custom-made Interface Board. The Panel PCs use identical Power Supply which can be supplied with 90-264 VAC, 18-36 VDC or as a multipower combination depending on configuration. Pixel pitch on all displays varies from 0.213 to 0.311 mm both in X and Y direction depending on the display size (see data sheet). Pixel pitch equals 1.07 m viewing distance with a viewing angle of 1 minute of arc as required in IEC 62288 section 7.5.1 for the 27" Panel PC, 0.96 m for the 24" Panel PC, 0.86 m for the 21" Panel PC, 1.02 m for the 19” Panel PC and 0.74 m for the 18.5" Panel PC. Nominal viewing distance in a normal environment is 1.0 m. Each Panel PC complies with the following international Standards and Requirements: All our Panel PCs have been tested by international accredited testing labs and found to comply with the requirements of the International Association of Classification Societies (IACS) as well as the selected requirements of IEC 60945, IEC 60533, IEC 60529, and selected MIL standards. The 19", 21ʺ, 24" and 27" Panel PCs have also been tested according to IEC 62288, IEC 62388, and IEC 61174 and are thereby ECDIS approved. All our Panel PCs are approved in compliance with the international standard IEC 60945:2002 (Clause 4.4 Equipment category b, protected from the weather (formerly class B)), Maritime navigation and radio communication equipment and systems - General requirements - Methods of testing and required test results.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 5 3. Product Identification On the backside there are three markings identifying the Panel PC. Display Unit (DIU) P/N and serial number Electronics Unit (ELU) P/N and serial number Complete Panel PC P/N and service tag number Upon request we can assign an additional customer specific P/N. Please see separate document for details about product numbering. 4. Packaging and Delivery Please check the delivered goods immediately on receipt with respect to damages caused by transportation and inform the delivering freight carrier immediately, on site, about any visible transport damages. Additionally, inform us immediately in writing, at the latest within 5 workdays, about any visible transport damages. At reception, the delivery includes the following items: Wave PERFORMANCE Monitor (Panel PC) AC power cable DC power plug (optional) DP cable (optional) 5. Mechanical Dimensions For panel cut out drawings and mechanical dimensions of Panel PCs see data sheets. 6. Compass Safe-distance: Every panel PC is tested in order to determine the minimum safe distances at which it should be installed from both the steering and the standard magnetic compasses, so not to significantly affect the accuracy of these compasses. A safe distance takes into account both the constant effect on a magnetic compass by the presence of magnetic material, but also any variable effect due e.g., electrical circuits or the opening/closing of drawers or panels. Thus, provided that a Panel PC is not placed in a position nearer to the center of the magnetic compass than the recommended safe distance, the Panel PC may be installed or removed without any need for adjustment of that compass. The safe compass distances are mentioned on every Panel PC and/or in the corresponding datasheet.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 6 7. Electrical Installation All electrical connections are to be found on the lower backside of the Panel PC. The connectors are clearly labelled on the Terminal Plate at the bottom of the Panel PC’s backside. Figure: Terminal Plate for a Panel PC with AC+DC power input and four serial ports. Optionally, two serial ports can be replaced with two additional Ethernet ports. 7.1. Pin-Assignments AC Power Pin Description Pin Description Pin Description N Neutral PE Protective Earth L Line The Panel PC is connected to AC voltage by means of the standard AC power cable included in the delivery. The AC current to the Panel PC is limited by a 3.15 A internal fuse. DC Power Pin Description Pin Description Pin Description 1 Supply voltage, positive 18-36V 2 NC 3 Supply voltage negative The Panel PC is connected to DC voltage by means of the DC power plug included in the delivery and wires suitable for up to 8 A continuous load. The Panel PC will not be damaged by reversed polarity; may it occur. The DC current to the Panel PC is limited by a 10 A internal fuse.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 7 Displayport Pin Description Pin Description Pin Description 1 ML_3LN (Lane 3-) 8 GND 15 AUXP (Auxiliary Channel+) 2 GND 9 ML_LN1P (Lane 1+) 16 GND 3 ML_L3P (Lane 3+) 10 ML_LN0N (Lane 0-) 17 AUXN (Auxiliary Channel-) 4 ML_L2N (Lane 2-) 11 GND 18 Hot Plug Detect 5 GND 12 ML_LN0P (Lane 0+) 19 POR (Return for Power) 6 ML_L2P (Lane 2+) 13 Config1 (connected to GND) 20 PO (Power 3.3V / 500mA) 7 ML_L1N (Lane 1-) 14 Config2 (connected to GND) RS232 – DB9 Plug Pin Description Pin Description Pin Description 1 Not connected 4 Not connected 7 Not connected 2 TxD (Transmit Data) 5 GND 8 Not connected 3 RxD (Receive Data) 6 Not connected 9 Not connected The Panel PC is equipped with two standard 9-pin D-SUB male connectors for RS232 serial ports. RS232 / 422 / 485 - DB9 Plug (optional) Pin Description Pin Description Pin Description 1 TxD- (Transmit Data) 4 RxD+ (Receive Data) 7 Not connected 2 TxD+ (Transmit Data) 5 GND 8 Not connected 3 RxD- (Receive Data) 6 Not connected 9 Not connected The Panel PC can be equipped with two additional standard 9-pin D-SUB male connectors for either RS232 or RS422/485 serial ports. The RS422/485 ports are configurable in the BIOS.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 8 LAN (RJ45) Pin Description Pin Description 1 DA+ 5 DC- 2 DA- 6 DB- 3 DB+ 7 DD+ 4 DC+ 8 DD- USB A Pin Description Pin Description 1 GND 3 Data + 2 Data - 4 Vcc HMI – DSUB 15 Pin Description Pin Description Pin Description 1 Backlight UP key 6 GPI (general purpose input) 11 Speaker line 2 Backlight DOWN key 7 GPO (general purpose output) 12 5 VDC 3 Reset key 8 PLED+ (Power LED anode) 13 PSU A Indicator 4 LED brightness control (PWM) 9 PLED- (Power LED cathode) 14 PSU B Indicator 5 Power key 10 Speaker return 15 GND Refer to the wiring diagram on next page for recommended used of the HMI port. An optional HMI panel can be supplied upon request.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 9

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 10 8. Operating System (OS) The Panel PC can be delivered with or without an installed OS. Currently only Windows and Linux OS is supported. Screen brightness can be adjusted using the Windows Display Settings. The following chapters assume that Windows 10 OS has been installed. 9. Color calibration and use in ECDIS applications The Panel PC may be color calibrated from factory. In this case, a set of calibration files will be provided to allow the operating system to apply the calibration when it is installed. The calibration files may be obtained from a USB pen-drive enclosed with the Panel PC or by mail. Please follow the procedure below to apply the calibration profile to the Microsoft Windows 10 operating system. 1. Press the Windows key + R together to get to the Run dialog box. Type “colorcpl” and press Enter to launch Color Management. 2. Select Display 1 from the drop-down list and tick “Use my settings for this device”. 3. Click the Add button, a dialog will open. 4. Click the Browse button to open the file select dialog. 5. Browse to the location of the calibration data. 6. Select the color profile (.icc) and click the add button. 7. The color profile containing the factory calibration will be added to the list of color profiles. 8. Select the profile that was just added and click the Set as Default Profile button. 9. The factory calibration profile has now been added and activated on the unit.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 11 Use in ECDIS applications: If the Panel PC is to be used in an ECDIS application, the appropriate ECDIS color table must be integrated into the ECDIS software. The ECDIS color table is provided as a .csv file that lists the RGB values required to produce each color token. The color table is provided along with the calibration data. 10. Simple Network Management Protocol (SNMP) It is possible to control the Panel PC backlight (brightness) and buzzer via Ethernet using SNMP. An SNMP agent must be installed using the following procedure: Microsoft .Net Core 3.1 is required to run the NorthSNMP agent. Make sure it is installed or install from this link: https://dotnet.microsoft.com/download/dotnet-core/thank-you/runtime-desktop-3.1.6-windows-x64-installer Download and install the SNMP agent according to the procedure below: 1. Create folder "c:\program files\NorthInvent\NorthSNMP" and copy files from NorthSNMP.zip to the folder. 2. Run the install.bat found in NorthSNMP.zip to install the service. Then open Windows firewall on UDP port 161 either by running the below commands in PowerShell or by using the Windows Defender graphical interface. New-NetFirewallRule -DisplayName "UPD161 SNMP IN" -Direction Inbound -Protocol UDP -LocalPort 161 -Action Allow -Profile Any New-NetFirewallRule -DisplayName "UPD161 SNMP OUT" -Direction Outbound -Protocol UDP -LocalPort 161 -Action Allow -Profile Any

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 12 1. Press Windows key and type wf.msc to open the firewall control panel 2. Select ”Inbound rules” and click “add rule” 3. Select ”Outbound rules” and click “add rule”.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 13 With the SNMP agent installed you can control the device by SNMP commands either through your dedicated application or by using one of the publicly available applications like NetSNMP (http://www.net-snmp.org/). The following examples presumes that NetSNMP is installed in the local machine: Control Command Get backlight value snmpget ‐v2c ‐cpublic localhost 1.3.6.1.4.1.30329.1.1.3.2.0 Set backlight 55% snmpset ‐v2c ‐cpublic localhost 1.3.6.1.4.1.30329.1.1.3.2.0 i 55 Turn on buzzer snmpset -v2c -cpublic localhost 1.3.6.1.4.1.30329.1.1.5.24.0 i 1 Turn off buzzer snmpset ‐v2c ‐cpublic localhost 1.3.6.1.4.1.30329.1.1.5.24.0 i 0 The backlight setting interval is 0-100% where 100% is max brightness. 11. System Utility and API The Panel PC uses an ITX motherboard manufactured by Congatec and a System Utility tool and an API are available from the Congatec Product page: https://www.congatec.com/en/products/mini-itx/conga-ic370/ 12. Technical Specifications Please refer to the relevant datasheet with the technical specifications for your type of Panel PC.

Specifications subject to changes without prior notice. The contents of this page are property of North Invent Norway AS. All rights herein are reserved to North lnvent Norway AS. This document cannot be reproduced without the written permission of the company. NORTH INVENT Sørhauggata 128, NO-5527 Haugesund, Norway Phone: + 47 48 84 02 00 [email protected] www.northinvent.com 14 13. Troubleshooting If you encounter any trouble with your Panel PC, please check if your problem is listed below and follow the given instructions. If the problem persists, please contact North Invent for service instructions. Problem Instructions No power on Check if the AC or DC voltage supplied to the Panel PC is within the specification (90-264 VAC or 18-36 VDC). Check if the AC or DC power LED is lit and if not press the power on control (HMI connected). No picture displayed Check if the brightness is set to 100% using the backlight UP key (HMI connected). Picture is too dark Increase the brightness using the backlight UP key (HMI connected). Increase the brightness using the Windows Display Settings (HMI not connected). OS is not loading Check if an OS was included in your purchase/delivery. 14. Cleaning Dust and dirt which typically accumulates on the front of the Panel PC, can easily be removed using a soft cloth moistened with hot water. A solvent can also be used but never use any kind of abrasive compound. Oil and grease can be removed using pure alcohol. The front glass can be cleaned with any solvent suitable for glass. 15. Maintenance and Service The Panel PCs are developed to be almost maintenance free. If the Panel PC malfunctions, please check if the problem can be solved with troubleshooting. If the problem persists, please contact North Invent for service instructions. Allow app. 1 hour stabilization time before measuring luminance and colors. 16. Update The technical documentation is subject to change. For an updated version please visit our website www.northinvent.com.