Omnimount UCL Installation Manual

Index Mounting the Wall Plate Mounting to Wooden Stud Mounting to Masonry Mounting the Cantilever Assembly Configuring the UM-1 Adaptor Plate Mounting the Display Adjusting the Display Roll Control Vertical Tilt Swivel 180° Pan Stowing the Screen Mounting the Wall Plate Mounting to Wooden Stud 1. Determine the location where you want the display mounted on the wall. 2. Use stud finder to locate and mark the center of the two studs. 3. Remove Plasma CL from box. Remove UM-1 Adaptor plate from the Mounting Head, and set the four 3/8”-16 button head cap screws aside for later. Note that the cantilever arm is mounted at the end of the wall plate for shipping. 4. Remove cantilever arm from Wall plate. 5. Align center mounting holes of wall plate with center marks on studs. Using the wall plate as a template, mark the mounting holes and center J box hole. Install J box as required. Note: Electrical outlets should only be installed by a qualified electrician. 1

(76 mm) deep. Mounting to Masonry 1. Using the wall plate as a template, mark the mounting holes in the desired mounting location. 2. Drill mounting holes with 3/8” (10mm) masonry bit. Mounting holes should be a minimum of 2 9/16” (65mm) deep. 3. Insert masonry mounting anchors (not supplied) into holes, and tap flush with hammer. Proceed to Mounting Cantilever Assembly Mounting Cantilever Assembly 1. Important: for the display to be centered over the wall plate when the cantilever arm is folded, the arm will need to be offset by approximately 4” (10.1 cm) from the desired center position of the screen. To do this, first note where the desired center of screen position intersects the wall plate, and then mark the wall plate. 2. Attach cantilever arm to the wall plate at the indicated offset location. 3. Mount cantilever assembly to wall using supplied 3/8” lag bolts. 4. Fold cantilever arm to verify center location of mounting head. Note: the mounting head will be centered with the arm folded in one direction only. Center of screen 2 mounting hole offset Cantilever arm assembly 2

Measure display The UM-1 ships with a standard set of mounting rails pre-installed. These rails will fit a display where the vertical distance between mounting lands on the display are 17 1/8” or less. If your display is larger than this, you will need to install the large set of mounting rails, which are included with the UM-1. Please see Install Mounting Rails at the end of this section for details. Set UM-1 width The UM-1 is capable of handling a wide range of landed insert widths. Measure the horizontal distance between mounting lands on your display, and set the width of the Mounting Rails as shown, Standard Range: 38 ½” (98 cm) to 15 ¾” (40 cm) Standard Configuration For standard range configurations, loosen the screws on the sliders using the supplied Allen wrench, adjust rails to desired width, and then re- tighten screws. Narrow Range: 15 ½” (39 cm) to 3 ½” (9 cm) Narrow Configuration For narrow range configurations, flip slider/rail assembly over (as shown below) before inserting them into the channels. Secure sliders and back plate Secure sliders with (8) button head screws. For medium and narrow displays, where the nuts on the slider are beneath the back plate, thread button head screws through the back plate and into the slider as shown. Note: The ou er co ne s of the back pla e must always be secured with a screw. t r r t For wide displays, where the nuts on the slider are positioned outside of the back plate, use lock nut with button head screws (supplied) to secure the back plate, as shown at right. 3

Hardware Selection a. Consult the supplied Hardware Cross Reference List. b. Select the mounting hardware for your display. Attach UM-1 to Display a. Position the UM-1 over back of display. b. Thread mounting screws through square washers and spacers (if required), as shown. c. Thread mounting screws through slots on side rails into landed inserts, and secure loosely. d. With mounting screws installed, center UM-1 on the back of the display, and then tighten all screws securely. CAUTION: Do not use power tools or over-tighten the mounting screws. Install Mounting Rails 1. Remove slider retaining screws as shown. 2. Remove sliders from channels. 3. Select required side rail size: Medium rail – up to 17 1/8” height of landed inserts Large rail – up to 25” height of landed inserts 4

5. Re-install slider assemblies into channels as shown, and return to Set UM-1 Width section. Mounting the Display 1. Locate the set of four 3/8”-16 button head cap screws removed at the beginning of the installation. 2. Thread two of the screws approximately a ¼” (.6 cm) into the upper set of PEM nuts on the adaptor plate, as shown. 3. With the help of an assistant, carefully lift the display and hang it onto the Plasma CL by dropping the exposed portion of the screws down into the key slots on the nose piece of the Plasma CL. 4. With the display hanging on the mount, thread the second set of screws into place, and then tighten all four screws securely. 5

Operation - Grasp the sides of the display, and roll it into the desired position. Adjusting Roll Tension – Roll tension is controlled by the two tension bolts located on the outer edges of the nose piece. Use an open-ended 9/16” wrench to make adjustments to the tension bolts by inserting wrench between the nose piece and the adaptor plate. Vertical Tilt Function – raising and lowering the screen edge to improve viewing angle/picture quality. Operation – Loosen tilt tension screws with supplied 3/16” Allen wrench as shown. Adjust display for desired tilt angle. Re-tighten tension screws. Swivel Purpose – Optimize viewing angle for off center viewing positions. Operation – Grasp edges of display and swivel into desired position. Adjust swivel tension – Adjust tension with supplied 3/16” Allen wrench. 6

Operation – Extend cantilever arm completely. Fully swivel display in desired direction. Note: Maximum screen size for full 180° Pan is approximately 50”. Stowing the Screen Purpose – Allows display to be folded flat to the wall. Operation – Grasp center pivot point of cantilever arm and edge of display. Fold arm in half at pivot point and push display back flat against wall. Centering the Screen The screen will be centered with the cantilever arm folded in one direction only, as shown. 7