OLT GardenSaver GS84D-Plywood Assembly Manual

(left door from outside/right from the inside) using 6 - 1 1/4” screws. Position on inside edge of left door frame so Flange overlaps right door frame by about 3/4”. Leave small gap between Stop and Flange. 67. Attach 2nd upper interior door trim as per Step 66. Position and attach all Side Interior Door Trim (4) (1/2” x 1/2” x 35 7/8”) 2 per/side. Position against door jamb and underneath upper door trim. Attach with 4 - 1 1/2” finishing nails. Complete lower interior door t ...

Floor Runners (5) Small Floor Joist Frame Exploded Floor Section A. Floor Section Exploded view of all parts necessary to complete Floor Section. Identify all parts prior to starting. Note: Floor Footprint is 96” wide x 45 1/2” deep. Foundation Material not included. 1. Lay out Large Floor Joist Frame and 2 Floor Joists (1 1/2” x 3 1/2” x 72”) as illustrated above. Position Joists equally in Floor Joist Frame. Use Small Floor Joist Frame as a template to determine joist position. Position Joist so flush with framing. 2. When c ...

Rear Wall framing. To help strengthen the Rear Walls, there is a short and a long wall cleat which meet off-center from the seam between walls. Attach Cleats with 8 - 1 1/4” screws. 99 1/4” 99 1/4” Advice: Prior to fastening walls and installing rafters, take time to confirm your walls are level, square and plumb. Measure diagonal at top and bottom of walls corner-to-corner. This should be approximately 99 1/4”. More importantly, if measurements are not within 1/4”, your ...

as unfinished products. If exposed to the elements, the Western Red Cedar lumber will weather to a silvery-gray color. If you prefer to keep the cedar lumber looking closer to the original color, we suggest that you treat the wood with a good wood stain. You may also wish to paint your new shed rather than stain it. In both cases we recommend that you consult with a paint and stain dealer in your area for their recommendations. We value your feedback and would like to hear back from you on how well we are doing in the following areas: 1. Customer Service 2. ...

Exploded view of all parts necessary to complete the Skirting, Trim, Facia and Miscellaneous Pieces. Identify all parts prior to starting. Rear Facia (2) Side Angle Cut Facia (2) Side Front Corner Trim (2) Front Corner Trim (2) Bottom Door Stop/Threshold Front & Rear / Side Skirting (6) Full Door (2) Black Tee Hinge (6) Door Hardware Vertical Door Trim (2) Front & Rear Facia Detail Plates (2) Front Facia (2) 43. Attach Bottom Skirting (3/4” x 4 1/2” x 45 1/4” - bevel) around the base of the shed. Skirting will hide floor framing. Start with side skirting pieces ...

Rear Soffit Boards (2) 48” 21” 43 1/2” 96” A. B. C. Rear Soffit Mid Rafter Mid Rafter Rear Front Soffit Screw center rafters together with 6 - 2 1/2” screws. Note: We recommend you drill a 1/8” pilot hole for each screw, to avoid splitting wood. The hole depth should be equal to 3/4 the length of screw. Confirm angles on rafter ends are aligned. 31. Locate 7 Rafters, 2 Rear Soffits and 2 Front Soffits. Center Rafter has 3/4” cleats attached on both sides making the width 3”. Lay out on level ground and assemble as shown in Illustrations A through C belo ...

Rear Soffit Boards (2) 48” 21” 43 1/2” 96” A. B. C. Rear Soffit Mid Rafter Mid Rafter Rear Front Soffit Screw center rafters together with 6 - 2 1/2” screws. Note: We recommend you drill a 1/8” pilot hole for each screw, to avoid splitting wood. The hole depth should be equal to 3/4 the length of screw. Confirm angles on rafter ends are aligned. 31. Locate 7 Rafters, 2 Rear Soffits and 2 Front Soffits. Center Rafter has 3/4” cleats attached on both sides making the width 3”. Lay out on level ground and assemble as shown in Illustrations A through C belo ...