LG 50PX1D Service Manual

LOCA. NO PART NO DESCRIPTION C629 C630 C631 C6605 C6608 C6609 C6611 C6615 C6617 C6703 C6706 C800 C8001 C8002 C8003 C8004 C8005 C8006 C8007 C8008 C8009 C801 C8010 C8012 C8013 C8014 C8015 C8016 C8017 C8018 C8019 C802 C8020 C8021 C8022 C8023 C8024 C8025 C8026 C8027 C8028 C8029 C803 C8030 C8031 C8032 C8033 C8034 C8035 C8036 C8037 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE226SF6DC 0CE226SF6DC 0CE107SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE476SF6DC 0CE106SK6DC 0CK104CF56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CE106VF6DC 0CK104CF56A ...

LOCA. NO PART NO DESCRIPTION C1718 C1719 C172 C1722 C1725 C1726 C1727 C1728 C1729 C1730 C1731 C1739 C1740 C1741 C1742 C175 C186 C190 C202 C202 C203 C204 C205 C205 C207 C207 C208 C209 C210 C211 C212 C212 C213 C213 C214 C214 C215 C215 C216 C216 C217 C217 C218 C219 C220 C221 C222 C223 C223 C224 C224 0CE476SF6DC 0CE476SF6DC 0CE106SK6DC 0CE477SF6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE476SF6DC 0CE476SF6DC 0CK104CF56A 0CE477SF6DC 0CK104CF56A 0CE476SF6DC 0CK104CF56A 0CE476SF6DC 0CE108DJ618 0CF4741L438 0CF4741L438 0CE4763F618 0CE106VF6DC 0CE10 ...

LOCA. NO PART NO DESCRIPTION C629 C630 C631 C6605 C6608 C6609 C6611 C6615 C6617 C6703 C6706 C800 C8001 C8002 C8003 C8004 C8005 C8006 C8007 C8008 C8009 C801 C8010 C8012 C8013 C8014 C8015 C8016 C8017 C8018 C8019 C802 C8020 C8021 C8022 C8023 C8024 C8025 C8026 C8027 C8028 C8029 C803 C8030 C8031 C8032 C8033 C8034 C8035 C8036 C8037 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE226SF6DC 0CE226SF6DC 0CE107SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE476SF6DC 0CE106SK6DC 0CK104CF56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CK102CK56A 0CE106VF6DC 0CK104CF56A ...

ADJUSTMENT INSTRUCTIONS 9-3. Adjustment of White Balance O Operate the Zero-calibration of the CA-100, then attach sensor to PDP module surface when you adjust. O Manual adjustment is also possible by the following sequence. (1) Enter ‘Ez - Adjust’ by pressing ADJ KEY on the Service Remote Control. (2) Select "7. WHITE PATTERN" using CH +/- Key and HEAT RUN at least 30 minutes by pressing the ENTER Key. (3) Receive the Window pattern signal from Digital Pattern Generator. (AV Input: connect the ‘HDMI’) (4) After attaching sensor to center of screen, select ‘5. White- Balance� ...

These instructions are applied to all of the PDP TV, AF-05FC. 2. Notes (1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test equipment. (2) Adjustments must be done in the correct order. (3) The adjustments must be performed in the conditions of 25±5°C of temperature and 65±10% of relative humidity if there is no specific designation. (4) The input voltage of the receiver be must kept 110V, 60Hz during adjustment. (5) The receiver must be operational for about 15 minu ...

DESCRIPTION OF CONTROLS...........................................4 SPECIFICATIONS.................................................................8 ADJUSTMENT INSTRUCTIONS ..........................................9 BLOCK DIAGRAM...............................................................14 EXPLODED VIEW...............................................................16 EXPLODED VIEW PARTS LIST .........................................17 REPLACEMENT PARTS LIST............................................18 SCHEMATIC DIAGRAM.......................................................... PRINT ...

EXPLODED VIEW 601 600 102 103 101 215 214 400 300 305 301 304 303 302 124 120 121 122 123 430 205 212 201 203 200 202 210 208 209 207 206 211 580 540 590 560 501 105 502 104 520 530 541 550 ...