HUANUO HNCM1 Instruction Manual

Manual Model: HNCM1 6 Thank you for choosing this HUANUO product! At HUANUO we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.huanuoav.com/reviews if you are satisfied. Should you have any issues, please don't hesitate to contact us. Technical Support: 1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN) Other Info: [email protected] (US/CA) Website: www.huanuoav.com

05 X1 X4 06 • Please read through these instructions completely before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact customer service at [email protected] • Check package contents against Supplied Parts and Hardware List to assure that all components were received undamaged. Do not use damaged or defective parts. If you require replacement parts, contact customer service at [email protected] • Not all parts and hardware included will be used. • Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product. IMPORTANT SAFTY INFORMATION X1 01 08 X1 X1 07 Check the VESA Pattern of Monitor Before the Installation Tools Required [Not Included] If your TV VESA is greater than 100x100 mm/4 x 4 in. or less than VESA 75 x 75mm/3 x 3 in., this mount is NOT compatible. If this mount is NOT compatible, please contact customer service at [email protected] to find a compatible mount. Minimum VESA Pattern: 3 in./75mm(W) x 3 in./75mm(H) MAX: 100 mm/4 in. MAX: 100 mm/4in. 100 mm ≈ 4 in. 75 mm ≈ 3 in. Support Pillar X1 02 Base X1 03 Monitor Connector X2 04 Monitor Plate Cable Clip Cable Clip Knob Grommet Plate 01 Drill(Optional) Screw Driver

01 02 08 01 02 A C Step 1-1 Secure the support pillar [01] to the base [02] using bolts [A] and Allen key [C] Step 1-2 Secure the support pillar [01] with base [02] to desktop using grommet plate [08] and knob [07] 07 D Note: If there isn’t a hole on your desk, you can use a 0.47 in.-1.18 in.(12 mm-30mm) drill to drill a hole. The drill is NOT included. φ 3/8（10mm） Bolt M4x12mm M-A X8 Bolt M4x16mm M-B X8 Bolt M5x12mm M-C X8 Bolt M5x16mm M-D X8 D5 Washer M-E X8 Spacer M-F X8 02 X1 C 4mm Allen Key X1 D 6mm Allen Key X3 A Bolt M5x18mm X2 B Bolt M3x8mm Nut

15/64 in.(6mm) Step 2-1 Slide the cable clip [05] and monitor connector [03] in sequence to the support pillar [01]. Step 2-2 Attach the cable clips [06] to the monitor connector [03], then secure the monitor connector [03] to support pillar [01] using Allen key [D] Step 2 06 Connect Cable Clip [05] and Monitor Connector [03] to the Support Pillar [01] D 05 03 01 03 01 03

Select Monitor Bolts Step 3 04 M-A/M-C M-E (If Needed) (If Needed) (If Needed) M-B/M-D M-E M-F FLAT BACK MONITOR (UNIVERSAL MONITOR PLATE) CURVED BACK MONITOR (UNIVERSAL MONITOR PLATE) Attach the Monitor Plates [04] to the Monitors Step 4 Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the monitor. -Too long will damage the monitor. 04

15/64 in.(6mm) B Step 5 Fix Tilt Angle of the Monitors Step 6 Secure Monitors to the Stand and Secure Using Nuts and Bolts [B] D B 05

5/32 in.(4mm) Store Allen Keys into the Cable Clip C 06

adjustment helps monitors to be perfectly aligned. Note: Please make sure two arms are aligned and balanced. D 07