JCM DBV 200 Quick Reference Manual

DBVTM 200 Units Note: Some of the information in this guide may change over time, depending on the soft- ware and possible modifications with advance- ments in technology. For further detailed information pertaining to procedures and troubleshooting methods, please contact our Technical Support Division of Cus- tomer Service. Technical Support (702) 651-3444 (800) 683-7248 Parts Sales Service Department (702) 651-3445 (702) 651-3446 E-Mail: [email protected] www.jcm-american.com

Quick Reference Troubleshooting Guide Description Probable Cause Possible Solutions Bill Rejection Dip switches not set properly Roller and/or belts are excessively dirty Credit limit not set properly on game Cashbox is full, or not installed properly Sensors out of calibration, unit not calibrated after software change Set Dip switches Clean head and rollers with mild soap and water solution Set credit limit for proper acceptance Check and verify cashbox’s condition • Calibrate unit using proper procedures • Check for proper software/ID protocol No Activity No power to the unit/ No LEDs visible Will not start acceptance procedure/ cycle Cycles, but will not accept bills Validator in an error status Bad CPU board Unit out of calibration Check power source, pins, wires and connector Check for proper software usage/ID protocol Check for proper Dip switch settings and game settings Run stand-alone test to verify Replace CPU board, or change out unit Calibrate unit using proper procedures

# of Blinks Description Possible Cause 1 2 3 4 5 6 8 10 12 15 Cashbox Full Jam in Cashbox Jam in Transport Unit Jam in Acceptor Head Motor Speed Error Motor Stop Error Solenoid Error Cashbox Removed Cheat Condition Detected D/A Adjustment Error • Cashbox may be FULL • Motor not functioning • Sensor not working • Encoder gear cracked or split • Pusher mechanism may be jammed • Stacker Encoder sensor not functioning • Cover open • Stacker lever problem • Bill remains in the carrying path • An object blocking sensors • Sensor problem • No signal from the Validator’s encoder sensor • Motor not functioning • Encoder gear cracked or split • Encoder sensor not functioning • Solenoid not functioning • The Stacker lever not at home position • No cashbox (SS units only) • Cashbox not seated properly • Sensors indicate possible sensor manipulation • Possible calibration sensor error DBVTM 200 Units

Use with Stand-Alone Test w/Rejections, or Host Simulator # of Blinks Description Possible Cause 1 2 3 4 5 7 8 9 10 12 13 14 15 Crooked insertion Magnetic pattern error Acceptor detected a bill while in stand-by Dark/Light ratio of bill is below fixed Value Transport feed error Photo pattern error Photo level error Return by inhibit settings Returned by host Detected another bill while a bill was still in stack mode Bill length error Color pattern error Return by other reasons (Magnetic error) • Bill was inserted crooked • Entrance sensor malfunction • Error detecting magnetic pattern on a bill/note • Detected the presence of a bill/ note while in stand-by • Reflective sensors may not be working properly • Bill/note not detected by the Transport feed sensor within a specified period • Bill/note may have a pattern not programmed in memory • Sensor may not be working properly • Dirty belts and/or rollers • Double/overlapping bill detected • The bill/note may be dirty • Bill/note does not fall into range of acceptable bills/notes, or denomination direction • Game program/settings will not accept inserted bill/note • Entrance sensor malfunction • Object blocking entrance sensor • Length of bill/note not within programmed specification • Irregular color/shade/markings • A combination error with magnetic sensors DBVTM 200 Units

DBVtm 200: Unit and Transport Unit • Replace belts if frayed, slick, and/or worn. • It is important to keep the bill path, rollers, and belts clean. The sensor lenses are transparent, and made of a polymer material. Handle them with care. To clean the lenses, use a lint-free cloth and a mild non-abra- sive detergent, such as liquid dish soap mixed with water. Do not use alcohol for cleaning Important Note: After wiping, inspect the lenses to ensure that none of the lenses have been moved out of position, or are not flush with the bill path. Note: JCM does not recommend cleaning cards, cleaning pads, or cleaning solutions of any kind CASHBOX PREVENTIVE MAINTENANCE (P/M) Do periodic PM on the cashboxes to ensure proper operation. Use compressed air via can or air compressor to blow out the paper fibers, and any other debris that builds up over time. Check the belts and all moving parts for wear and proper posi- tioning. If this unit does not operate properly, it can cause bill jams. After completing the PM, we recommend calibration. “DBVTM 200 Units”

for Basic Operations U.S. “$” Dollar DS1 DS2 On Off 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 Denomination/Interface use Diagnostic Use $1 $5 $10 $20 $50 $100 * * * I/F * Not Applicable NOTE: When Dip switches are in the “ON” position, it disables the acceptance of that bill denomination. DBV-200 ID-004/Bar (I/F) “On”: Accept Coupons & Currency “Off”: Default Accept Currency Only DBV-200 ID-011/015 (I/F) “On”: for I/F ID-015 “Off”: Default for I/F ID-011 DBV-200 ID-022/023 (I/F) “On”: for I/F ID-022 “Off”: Default for I/F ID-023 DBV-200 ID-044P/045P (I/F) “On”: for I/F ID-045P “Off”: Default for I/F ID-044P DBV-200 ID-044/045W (I/F) “On”: for I/F ID-045W “Off”: Default for I/F ID-044 1 2 3 4 5 6 7 8 9 10

1. Power Off 2. Set DIP Switch DS2: 4,5, and 6 “On.” DS1 DS2 On Off 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 Denomination/Interface use Diagnostic Use 3. Power-on Unit (plug in the 6-pin connector) 4. Head motor will cycle and stop - Ready to Calibrate 5. Insert the DBV-200 calibration paper, black side first (Part No. 057619). After inserting the calibration paper, the unit will carry the paper for- ward/reverse several times. When the process is complete, the unit will return the paper. Look at the indicator for proper signals: 14-pin Test LED, or the bezel light, if used. Fast Blinks indicate acceptable calibration, and Blinks from 1-11 at intervals of 1/2 second indicate an error as described below. # of Blinks Error Found During Calibration 1 Entrance Level Error 3 Entrance Sensor Error 5 Gain Error White Level Adjustments 6 Digital/Analog Error White Level Adjustments 7 Barcode Sensor Error 9 Magnetic Setting Error 10 Write-in Error 11 Black Level Error

Stand-Alone Test Mode Set the Dip switches then apply power to the unit to accomplish this function Note: Perform this test outside the game using the game power (6- pin) connector, or power supply hook-up • Before applying power, turn Dip switch “6” to “On”. • Apply power, then turn Dip switch “6” to Off. The unit should cycle. • The unit is ready for stand-alone testing • Insert a Bill/Note. It will either be accepted and go completely through the bill head, or be rejected. • If the unit rejects the Bill/Note, refer to the “Bill Return Codes” table. • If the unit will not take the Bill/Note in, check the “Abnormal Initialization Codes” table. • When the unit cycles on power up, this indicates power and forward motor operation. • When you insert a plain piece of paper and it is rejected, this indicates reverse motor operation. • When you insert various denominations of currency and they are accepted, this indicates the Bill/Note was accurately matched against the characteristics of the software version.

Downloading - Using the JCM DT-004 Download Tool DO NOT USE the 2-pin connector for power input. This is output power and can damage the DT-004. 1. Make sure power is applied to the DT-004 via a 3-pin connector from the PS15-007 power supply with the adaptive harness, Part No. 400-100067, or the power supply harness connection in the game. 2. With the power off, be sure the 4MEG Program EPROM is installed properly. 3. Dip switches: On DBV-200 units, set Dip Switches: DS1 - #1 to the “On” position, and all others to the “Off” position. DS2 - All to the “On” position. DT-004 - All to the “Off” position. 4. Harnessing • For standard DBV-200 SS/SH/SU units, use the following JCM parts: • PS15-007 Power Supply, Part No. 550-100040, with adaptive harness Part No. 400-100067. • Harnesses Part No. 400-100065 and 400-100066 for data and power to the DBV-200 unit. • For the B424 model DBV-200, use harness Part No. 400- 100042 in conjunction with harness Part No. 400-100069 to complete the connection. 5. Turn the power switch on the DT-004 to the “ON” position. The Power LED should light. 6. Verify the LEDs on the DBV-200 CPU board are illuminated, and are blinking back and forth. This indicates download mode. 7. To begin the download process, press the “START” button. The “RDY” LED should begin to blink. (Cont’d)

(Cont’d.) 11.Turn power on the DT-004 to the “OFF” position, remove the harness connectors from the unit, and return the Dip switches to their normal operating positions. 12.To repeat the process with other units, follow these instructions from #3 through #10. NOTE: After downloading/upgrading the units, re-calibrate the units. 9. When the downloading is complete, the “OK” LED will light and a buzzer will sound for about a second. 10.Press the “RESET” button once, then press the “VERIFY” button once. After approximately 10 seconds, a buzzer will sound for about a second, and the “OK” LED will illuminate. 8. While downloading, the download status LEDs on the DT-004 will illuminate, indicating status of the download.

This is an example of the various usages for JCM interfaces WBA - I/F ID Interface OEM (Gaming Manufacturer) DBV - I/F ID-004/Bar JCM Standard: CDS and VLC ID-011/015 Sigma and Videotronic ID-022/023 IGT: S-Slots, P.E., P.E. Plus ID-024 IGT: Game King, I-Game, and Vision Series ID-044P/-45P Bally ID-044/045W WMS DBVTM 200: DT-004 ID Interface OEM (Gaming Manufacturer) ID-003 JCM Standard:Aristocrat, Atronics, Bally, CDS, Sigma, VLC, and WMS ID-022/-23 IGT: S-Slots, P.E., P.E. Plus ID-024 IGT: Game King, I-Game, and Vision Series ID-044C/0C3 Aristocrat

Regional Offices Western Region: Main 925 Pilot Road Las Vegas, NV 89119 (800) 683-7248 Office (702) 651-0000 Fax (702) 651-0214 Mid-Western Region 3000 Dundee Road, Ste. #402 Northbrook, IL 60062 Office (847) 418-3354 Fax (847) 418-3357 Eastern Region 3 Canale Drive, Ste. #4 Egg Harbor, NJ 08234 Office (609) 677-8909 Fax (609) 677-8820 Southern Region 4063 Ginger Dr., Ste. B Biloxi, MS 39532 Office (228) 354-8600 Fax (228) 354-8608 DBV-200 Quick Reference Manual Part No. 960-000028  2001, JCM American Corp.