Inter-fab EDGE ANSI/NSPI-5 Assembly/installation Instructions
Read Online
Read the Inter-fab EDGE ANSI/NSPI-5 Assembly/installation Instructions online using the built-in PDF viewer.
Text of the manual
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
E D G E D I V I N G B O A R D
E D G E C O M P O S I T E S P R I N G S
E D G E F I B E R G L A S S S T A N D
Assembly & Installation Instructions
3 0 5 0 S . A L V E R N O N W A Y • T U C S O N , A Z 8 5 7 1 3
5 2 0 . 7 9 0 . 7 0 4 0 • 8 0 0 . 7 3 7 . 5 3 8 6 • F A X 5 2 0 . 7 9 0 . 7 1 2 7
i n t e r - f a b . c o m
For Technical Support or Assistance,
Contact Customer Service at:
INTER-FAB, INC.
3050 S. ALVERNON WAY
TUCSON, AZ 85713
(800) 737-5386
or visit: www.inter-fab.com
To obtain complete copies of the ANSI/NSPI-5 2003
Standard for Residential Inground Pools or to obtain
copies of the “Plan Your Dive, Steer Up” or “The
Sensible Way to Enjoy Your Inground Swimming Pool”
contact:
The Association of Pool & Spa Professionals
(APSP)
2111 Eisenhower Ave.
Alexandria, VA 22314
(703) 838-0083
or visit: www.theapsp.org
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
1
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
TABLE OF CONTENTS:
Safety First .........................................................................2-3
Important Notices to the Installer..............................................4
Minimum Diving Water Envelope Information...............................5
Edge Fiberglass Base Placement...............................................6
Edge Diving Board Dimensions..................................................7
Edge Jig Information................................................................7
Installation Instructions .........................................................7-8
Edge Fiberglass Base Exploded View & Parts List........................9
Article 5 Extracted from ANSI/NSPI-5 2003 .......................10-15
Inter-Fab Limited Warranty.....................................................16
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
2
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
This Inter-Fab diving board and stand shall be installed only by a professional swimming pool contractor
or with the direct supervision of a licensed professional, engineer or architect. Diving boards may
be installed only on residential inground swimming pools properly designed for their use.
Diving boards that are improperly installed can be very dangerous to the user resulting in possible
serious head and/or spinal column injury, including the paralysis or death of the user.
It is very important that this diving board and stand be installed only on Type 1 or greater pools
built in strict accordance with the American National Standard for Residential Inground Swimming
Pools (ANSI/NSPI-5 2003) and in accordance with the included INTER-FAB RESIDENTIAL POOL
SPECIFICATIONS TABLE 2.
In addition to the above standard and referenced table, these installation instructions provided by
Inter-Fab, Inc. must be diligently followed.
It is also important that any and all warnings provided with the diving board be strictly adhered to
and posted in a conspicuous location. If not provided or they are misplaced, please purchase
warning signs from your pool contractor or professional pool supply store and post them in a location
that the users of the diving board can clearly see.
SAFETY FIRST!
DIVING TIPS: Even the safest equipment must be used properly. Inter-Fab promotes safe diving by
offering these tips on the proper use of your diving board: always dive into water that meets depth
requirements, with arms extended; be aware of the bottom and the walls of the pool; avoid collisions
with pool toys and floats; and instruct your pool users to always “steer up”. When you begin your
dive you must get ready to steer up. As you enter the water, your arms must be extended over
your head, hands flat aiming up. Hold your head and arch your back.
FOR RESIDENTIAL INGROUND SWIMMING POOL USE ONLY
NO COMMERCIAL, PUBLIC OR SEMI-PUBLIC USE IS ALLOWED
ONLY ONE PERSON ON THE DIVING BOARD AT ONE TIME
MAXIMUM WEIGHT = 300 LBS
Plan Your Dive
Back Arched
Arms Extended
Head and Hands Up
Hold Diving Form
Steer up for a safe dive.
PLAN YOUR DIVE, STEER UP
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
3
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
“A pool is the safest place to swim and a diving board installed in compliance with manufacturers
instructions and the 2003 ANSI/NSPI Standard for In-ground Residential Pools is the safest place
to dive from. To ensure that you and your family and guests are able to safely enjoy your diving
board for many years, it is critical that you follow the following instructions.”
SAFETY FIRST!
DO
1.
Know the shape and depth of the pool before
you dive.
2.
Make sure that all family members and guests
are familiar with these instructions before they
use your pool and diving board.
3.
Make sure that the diving board has been
installed in compliance with the Assembly and
Installation Instructions and with the 2003
ANSI/NSPI Standard for In-ground Residential
Pools. This includes the shape and depth of
the pool as well as the height of the diving
board.
4.
Enter feet first the first time.
5.
Plan your path to be sure you avoid any other
swimmers, or objects in or under the water,
such as floats, tires, toys etc.
6.
Keep your head up, arms up and fully extended
and steer up with your hands.
7.
Practice carefully before you dive headfirst.
8.
Become familiar with the diving board and its
spring before diving headfirst
9.
Dive straight ahead, not to the side of the
board or pool.
10. Dive from the diving board only.
11. Make sure that children and non-swimmers
are supervised at all times.
12. Always remember that when you dive you must
steer up.
13. Inspect your diving board, base and stand on
a regular basis (at least twice a year) and keep
them in proper repair.
14. Contact your dealer, installer or Inter Fab
(800-737-5386) with any questions or concerns
about the safe use of your diving board.
DON’T
1.
Don’t drink and dive.
2.
Don’t install this or any diving board on an
above ground pool or dive into an above
ground pool from any surface.
3.
Don’t dive into a pool from anyplace not specif-
ically designated for diving. Never dive into the
shallow portion of any pool.
4.
Don’t dive across the width of the pool or to
the sides of the pool.
5.
Don’t Run and dive.
6.
Don’t engage in horseplay in or around the diving
board or pool.
7.
Don’t use your diving board as a trampoline.
8.
Don’t do a back dive. Backyard pools are not
built for that type of activity.
9.
Don’t try fancy dives. Keep the dives simple.
10. Don’t dive into or through objects or toys such
as inner tubes.
11. Don’t swim or dive alone.
12. Don’t use a diving board or stand or base that
is rusted or worn out or in poor repair.
THE EDGE DIVING SYSTEM IS A JUMP BOARD
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
4
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
The specifications found on page 5 of this manual represent the minimum water envelope
required by Inter-Fab and by the ANSI/NSPI-5 2003 Standard for residential Inground Swimming
Pools. Each of these dimensions must be met or exceeded. Installation of a diving board of any
type on a pool that does not meet or exceed each of the minimum specifications as provided on
page 5 including but not limited to the slope requirement, is in direct violation of this manufacturer’s
instructions and the 2003 Standard, and can result in serious injury or death.
Installation of this Edge Fiberglass Stand and Edge Diving Board is limited to Residential Inground
Pools ONLY.
There is only one Edge Fiberglass Stand and only one Edge Composite Spring Set. You can install
either a 6’ or 8’ Edge diving board on this assembly in accordance with Table 1- Minimum Water
Envelope ANSI/NSPI-5 2003 and Table 2- Inter-fab Residential Pool Minimum Specifications on
page 5. Installing any diving board greater than 8’ on any Edge Stand is strictly prohibited.
Inter-Fab Edge Diving Boards are designed for use only with the Edge Diving Stand and Edge
Composite Spring Set. Edge components are only compatible with other Edge components.
Comply with local government regulations for Residential Inground Swimming Pools if they exceed
the ANSI/NSPI-5 2003 Standard for Residential Inground Swimming Pools.
DO NOT USE ANY EDGE DIVING COMPONENTS WITH NON-EDGE COMPONENTS!
Read carefully pages 10–15 of this installation manual which contain portions of the ANSI/NSPI-5
2003 Standard for Residential Inground Swimming Pools, ensure that you understand the minimum
required diving water envelope in Figure 3 and Table 1 provided in the ANSI/NSPI-5 2003 Standard.
NOTE: The installation of this Edge Diving Stand/Edge Diving Board is not complete until you, the
installer have measured the pool as well as the diving board’s overhang, height above water and
the fulcrum distance to ensure they meet the Inter-Fab’s Residential Pool Minimum Specifications
and the ANSI/NSPI-5 2003 Standard for Residential Inground Swimming Pools. In addition; the
installation of this commercial diving board is not complete until you the installer have delivered to
your customer and reviewed with your customer the “Owners Manual” as well as the “Plan Your
Dive Steer-Up” brochure.
IMPORTANT NOTICES
TO THE INSTALLER
THE EDGE DIVING SYSTEM IS A JUMP BOARD
ONLY ONE PERSON AT A TIME ON THE DIVING BOARD,
WITH A MAXIMUM WEIGHT LIMIT OF 300 LBS.
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
5
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
MINIMUM DIVING WATER ENVELOPE:
NOTE: DRAWINGS ARE NOT TO SCALE.
NOTES:
DIVING EQUIPMENT
TIP OF BOARD
ABOVE POINT A
D I V I N G
E Q U I P M E N T
P R O H I B I T E D
D I V I N G
E Q U I P M E N T
P R O H I B I T E D
A
B
C
D
A
B
C
D
WA+/-3”
AB
BC
CD*
DE
WE
0
I
6’-0”
7’-6”
5’-0”
2’-9”
10’-0” 12’-0” 10’-0”
8’-0”
1’-6”
7’-0”
7’-6” VARIES 6’-0”
28’-9”
II
6’-0”
7’-6”
5’-0”
2’-9”
12’-0” 15’-0” 12’-0”
8’-0”
1’-6”
7’-0”
7’-6” VARIES 6’-0”
28’-9”
III
6’-10”
8’-0”
5’-0”
2’-9”
12’-0” 15’-0” 12’-0”
8’-0”
2’-0”
7’-6”
9’-0” VARIES 6’-0”
31’-3”
IV
7’-8”
8’-6”
5’-0”
2’-9”
15’-0” 18’-0” 15’-0”
9’-0”
2’-6”
8’-0”
10’-6” VARIES 6’-0”
33’-9”
V
8’-6”
9’-0”
5’-0”
2’-9”
15’-0” 18’-0” 15’-0”
9’-0”
3’-0”
9’-0”
12’-0” VARIES 6’-0”
36’-9”
POOL
TYPE
MINIMUM DEPTHS
AT POINT
MINIMUM WIDTHS
AT POINT
MINIMUM LENGTHS
BETWEEN POINTS
TABLE 1 - MINIMUM WATER ENVELOPE (ANSI/NSPI-5 2003)
DBL**
HOW**
F
G
H
J
K
L
M
N
0
I
6’ DB/6’ JB
20”
2’-9”
5’-0”
4’-0”
7’-2.5”
7’-6”
6’-0”
3’-9”
2’-1.5”
12’
II
8’ DB/6’ JB
20”
2’-9”
3’-10”
4’-2”
7’-2.5”
7’-6”
6’-8”
3’-9”
2’-1.5”
12’
III
10’ DB/8’ JB
26”
2’-9”
4’-4.75”
4’-4.5”
7’-5.5”
8’-0”
6’-7”
3’-11.5”
1’-7.5”
13’
IV
10’ DB/8’ JB
30”
2’-9”
5’-10.5”
3’-10”
7’-8”
8’-6”
8’-3”
5’-7”
2’-7”
13’
V
12’ DB/8’ JB
40”
2’-9”
6’-2”
3’-11.5”
7’-9.5”
9’-0”
8’-2.5”
5’-9”
2’-7”
14’
POOL
TYPE
MAX. DIVING
BOARD
LENGTH
MAX. HEIGHT
OVER WATER
AT POINT A
CROSS SECTIONAL
DIMENSIONS AT
POINT A
CROSS SECTIONAL DIMENSIONS AT POINT B
TABLE 2 - INTER-FAB RESIDENTIAL POOL MINIMUM SPECIFICATIONS
MIN. HEAD
ROOM
ABOVE
DIVING
SURFACES
*Min. length between points CD may vary based upon water depth at point D and the slope between points C & D
ABBREVIATIONS: **DBL=Diving Board Length; DB=Diving Board; JB=Jump Board; **HOW=Height Over Water
F
G
H
J
K
N
M
L
DIVING EQUIPMENT
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
6
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
TABLE 3 – PLACEMENT CHART
ADDITIONALLY REFER TO: ANSI/NSPI-5 2003 American National Standard for Residential Inground Swimming
Pools and to page 5 for Inter-Fab Residential Inground Pool Minimum Specifications.
NOTE: WHEN COPING IS USED, DO NOT SET FRONT JIG BOLTS CLOSER THAN 3” FROM THE
BACK EDGE OF THE COPING.
* IMPORTANT: The distance for setting the front jig bolt (S) from the water’s edge is valid only if the minimum water depth is maintained
at the tip of the board noted as point “A” in ANSI/NSPI-5 2003 American National Standard for Residential Inground Swimming Pools.
If minimum water depth is not maintained the distance (S) must be adjusted accordingly.
** “WA” dimension is valid only in conjunction with the minimum depth at point “A” for type pool in accordance with ANSI/NSPI-5
2003 American National Standard for Residential Inground Swimming Pools.
NOTE: READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE
ATTEMPTING THE INSTALLATION.
IMPORTANT:
THESE DIMENSIONS
ARE ACCURATE ONLY
FOR VERTICAL POOL
WALLS, TYPICALLY
GUNITE CONSTRUC-
TION, WITH LESS
THAN A 3’ RADIUS TO
THE POOL FLOOR.
DUE TO THE VARYING
SIZES
OF
OTHER
POOLS, TYPICALLY
VINYL LINER CON-
STRUCTION, PLEASE
CONTACT CUSTOMER
SERVICE FOR PROPER
JIG PLACEMENT.
1-800-737-5386
EDGE
DIVING
SYSTEM
PART #
NOMINAL
BOARD
LENGTH
ANSI/
NSPI-5
POOL
TYPE
DISTANCE FROM
WATER’S EDGE TO
FORWARD JIG BOLT
(S)
DISTANCE FROM
END OF BOARD TO
FORWARD JIG BOLT
MAX HEIGHT
OF BOARD
ABOVE
WATER
(HOW)
EDGE-BASE
6’
I
31.5”
49.5”
18”
20”
EDGE-BASE
6’
II
31.5”
49.5”
18”
20”
EDGE-BASE
6’
III
25.5”
49.5”
24”
26”
EDGE-BASE
6’
IV
19.5”
49.5”
30”
30”
EDGE-BASE
6’
V
13.5”
49.5”
36”
40”
EDGE-BASE
8’
I
EDGE-BASE
8’
II
EDGE-BASE
8’
III
44.25”
68.25”
24”
26”
EDGE-BASE
8’
IV
38.25”
68.25”
30”
30”
EDGE-BASE
8’
V
32.25”
68.25”
36”
40”
MIN.
OVERHANG
PLUS OR
MINUS 3”
(WA)
Cannot put 8' jump board on type I pool
Cannot put 8' jump board on type II pool
FIG. A – EDGE FIBERGLASS BASE PLACEMENT SPECIFICATIONS:
INTER-FAB CANNOT GUARANTEE CUSTOMER’S CONCRETE OR THICKNESS
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
7
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
FIG. B – 6’ EDGE DIVING BOARD
TABLE 4 – BOARD DIMENSIONS AND FULCRUM SETTINGS
Model #
Nominal Length
A
B
C
D
F
DIA.
EDGE 6
6’
70.25”
17.25”
6.31”
4.00”
42.50”
.625”
EDGE 8
8’
94.00”
17.25”
6.31”
9.00”
42.50”
.625”
TABLE 5 – JIG DIMENSIONS
Jig Type
A
B
C
BOLT
Edge Fiberglass
12”
12”
6”
1/2” X 6”
FIG. C – EDGE JIG
INSTALLATION INSTRUCTIONS: Edge Fiberglass Stand and Edge Diving Board
Be sure the concrete deck surrounding the anchor jig complies with the minimum dimensions as
shown in Figure A on pages 6.
Read and understand the ANSI/NSPI-5 2003 American National Standard for Residential Inground
swimming Pools and Table 1 and Table 2 on page 5 before you install Edge Fiberglass Stand and/or
Edge Diving Board.
The Edge four-bolt jig should be set in accordance with Table 3 on page 6. The diving board must be
placed on the deep end of the pool on centerline.
The tip of the diving board must be positioned directly over Pt. A as shown on page 5 and according
to the ANSI/NSPI-5 2003 Standard and Inter-Fab’s Residential Pool Minimum Specifications
Make sure the jig anchor bolts project out of the concrete deck 1-1/2” for the Edge Stand with
ample concrete depth below the jig in accordance with Figure A on page 6. Do not install the Edge
Diving System if the deck does not meet the minimum requirements.
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
8
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
When finishing the deck surface, maintain a level deck where the jig bolts project out so the dive
stand makes uniform contact with the deck surface. Allow the cement to fully cure before bolting
the dive stand to the jig bolts.
Before bolting the dive stand to the jig bolts, chisel away any excess concrete that may have built
up around the jig bolts then remove the protective yellow rubber bolt caps.
The top surface of the diving board from the deck end to
the tip end shall be level or have an upward slope of 5/8"
per foot maximum. Elevation difference shall not exceed
6" from the deck end to the tip of the board. There shall
be no downward slope towards the water. The slope shall
be measured using a level as shown in the graphic to the
left.
ONLY ONE PERSON ON THE JUMP BOARD AT A TIME, WITH A MAXIMUM WEIGHT
OF 300 LBS.
INSTALLATION INSTRUCTIONS: Continued
FIG. D
Edge Springs
FIG. E
Edge Fiberglass Base
POOL WATER
POOL WATER
STEP ONE:
Lay the Edge board upside down on the box it was shipped in. Attach the Edge Springs to the board
with hardware kit EDGE-M. The long leg of the spring faces towards the pool as shown in Figure D.
Use exploded view on page 9 for reference. Hand tighten only at this point.
STEP TWO:
Lay the base upside down on the springs and align the 3 holes in each spring center to the base.
Orient Edge Base to pool as shown in Figure E. Use hardware kit EDGE-SP and bolt springs to base.
Use exploded view on page 9 for reference. Tighten the 6 bolts from base to springs at this time
to 20-25 FT-LBS.
STEP THREE:
Turn the assembly over and tighten the board to spring hardware that was only hand tightened in step one.
STEP FOUR:
Place the Edge stand over the four jig bolts and secure with hardware kit TS-BK. Tighten the Stand
Anchor Hex Nuts to 40-45 FT- LBS. Do not over tighten.
The Diving Board must be installed according the below board leveling instructions:
HARDWARE NOTE: Use a small dab of anti seize lubricant (included) on all bolt threads.
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
9
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
EDGE DIVING SYSTEM (EDGE6WW, EDGE-BASE, EDGE-SPRING-GR):
DRAWING REPRESENTS THE
FOLLOWING PART NUMBERS:
EDGE-BASE (shown)
EDGE-SPRING-GR (shown)
NOTE: EDGE6WW diving board shown in exploded view for illustration purposes. Must be purchased separately.
ITEM #
COMPONENT
DESCRIPTION
TS-BK
EDGE-SP
EDGE-M
N/A
KITS – QTY. COUNTS
1
EDGE-BASE
Edge Diving Base
1
2
EDGE-SPRING
Edge Spring
2
3
EDGE-BOARD
Edge Diving Board
1
4
TS-EDGE-J
Edge Jig
1
5
Spring Pad (factory installed)
Edge Spring Pad
2
6
H-WHT WAS/CAP
IFI White Washer Cap
2
7
H-SS 1/2X13X4C
1/2" X 13 X 4" Carriage Bolt S.S.
2
8
H-SS 1/2 F WASH
1/2" Flat Washer S.S.
4
4
9
H-SS 1/2 LOC WA
1/2" Lock Washer S.S.
4
2
10
H-SS 1/2 H NUT
1/2" Hex Nut S.S.
4
2
11
H-1-1/2 WHT CAP
.750 x 1-1/2" White UV Nut Cap
4
2
12
H-1/2 NYLON WAS
1/2" Flat Nylon Washer
4
13
H-SS 3/8-16X2-1/2
3/8" x 2 1/2" Hex Head Bolt S.S.
6
14
H-SS 3/8 FLT WA
3/8" Flat Washer S.S.
12
2
15
H-SS 3/8 LOC WA
3/8" Lock Washer S.S.
6
2
16
H-SS 3/8X3-1/2C
3/8" x 3 1/2" Carriage Bolt S.S.
2
17
H-SS 3/8 F NUT
3/8" Finish Hex Nut S.S.
6
2
18
H-.531 X 1.00 CAP
.531 x 1.00 White Protective Cap
2
19
H-1/2 BLK WASH
1/2" x 2" dia. Black Rubber Washer
2
20
H-ANTI-SEIZE
Packet of Anti Seize Lubricant (not shown)
1
1
HARDWARE NOTE:
Use a small dab of
anti seize lubricant
(included) on all bolt
threads.
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
10
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
SUPPORT INFORMATION:
ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
Extracted from ANSI/NSPI- 2003, American National Standard for Residential Inground Swimming Pools
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
11
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
SUPPORT INFORMATION:
ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
Extracted from ANSI/NSPI- 2003, American National Standard for Residential Inground Swimming Pools
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
12
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
SUPPORT INFORMATION:
ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
Extracted from ANSI/NSPI- 2003, American National Standard for Residential Inground Swimming Pools
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
13
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
SUPPORT INFORMATION:
ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
Extracted from ANSI/NSPI- 2003, American National Standard for Residential Inground Swimming Pools
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
14
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
SUPPORT INFORMATION:
ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
Extracted from ANSI/NSPI- 2003, American National Standard for Residential Inground Swimming Pools
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
15
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
SUPPORT INFORMATION:
ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
Extracted from ANSI/NSPI- 2003, American National Standard for Residential Inground Swimming Pools
To obtain complete copies of the ANSI/NSPI-5 2003 Standard
for Residential Inground Pools contact:
The Association of Pool & Spa Professionals (APSP)
2111 Eisenhower Ave.
Alexandria, VA 22314
(703) 838-0083
or visit: www.theapsp.org
I N S T A L L A T I O N M A N U A L
E D G E ™ D I V I N G S Y S T E M
16
EDGE-IM Rev. 6/08 (BBK-EDGE INSTAL)
CUSTOMER SERVICE/TECHNICAL SUPPORT – Mon – Fri: 7am – 4pm MST
520.790.7040 • 800.737.5386 • Fax 520.790.7127 • inter-fab.com
3050 S. Alvernon Way • Tucson, AZ 85713 • [email protected]
LIMITED WARRANTY
Inter-Fab, Inc. will repair or replace, at its option, any product manufactured by Inter-Fab, Inc. that fails during
the applicable warranty period because of a manufacturing or material defect; provided that the defect is not
the result of improper installation, improper use or care, negligence or natural accidents (acts of God). The
applicable warranty period for products manufactured by Inter-Fab, Inc. is three (3) years from the date of
retail purchase, except as specified below:
Echoes of Nature™ products are individually handcrafted and painted by skilled artisans and as a result,
dimensional differences and color variations are normal and are not a basis for warranty coverage. The warranty
period for pumps sold with the Echoes of Nature™ products is three (3) years from the date of retail purchase.
Water Sports™ sports equipment warranty periods are as follows: Volleyball Poles, Basketball Posts,
Basketball Rim, and Basketball Backboard one (1) year from date of retail purchase; and Volleyball, Volleyball
Net, Basketball, Basketball Net, and Pumps are warranted for ninety (90) days from date of retail purchase.
T7™ Edgewater™ and Lighted Edgewater™ features warranty period is one (1) year from date of retail purchase.
Zoomerang™ slide products warranty period is one (1) year from the date of retail purchase.
Build Your Own Slide™ (BYOS™) warranty period is one (1) year from the date of retail purchase.
City 2™ Slide and City Base™ products warranty period are one (1) year from the date of retail purchase.
Unless expressly stated otherwise all products manufactured by Inter-Fab are for residential installation and
use only. Inter-Fab, Inc. expressly disclaims any and all warranties and liability arising from the installation or
use of its residential products used in a commercial application. Products expressly manufactured for commercial
installation and use will be subject to this limited warranty.
This limited warranty is in lieu of all other warranties, whether express or implied. Inter-Fab, Inc. disclaims
any warranty of merchantability or fitness for a particular use, and noninfringment in relation to any of its products
and Inter-Fab, Inc. is not liable for consequential, incidental or specific damages. This warranty is limited to
the repair or replacement of the manufacturing or material defect, or refund of the original purchase price,
whichever is less, at the sole option of Inter-Fab, Inc., and expressly does not cover any labor or reinstallation
expenses related to the replacement of any and all Inter-Fab products. This limited warranty shall be the sole
and exclusive remedy of irrespective of whether the claims are made in contract, tort, warranty, law, equity
or by statue.
This warranty is to the original purchaser of the product only. Inter-Fab’s limited warranty is neither transferable
nor portable from consumer to consumer. The effective coverage date begins at the date of retail purchase.
Product owner or representative must notify Inter-Fab, Inc. (or its wholesale agent) in writing, giving a full
description of the nature of the product defect or failure along with proof of purchase, serial number(s) of the
product and photos within thirty (30) days of the expiration of the applicable warranty period. Inter-Fab, Inc.
reserves the right to physically inspect damaged or defective products or components to determine the cause
of the damage or defect, prior to authorizing repair or replacement of its products.
