M-system KSL2 Instruction Manual

Thank you for choosing M-System. Before use, please check contents of the package you received as outlined below. If you have any problems or questions with the product, please contact M-System’s Sales Office or representatives. ■ PACKAGE INCLUDES: DC alarm (body + base socket + input resistor) ................(1) Input resistor is provided only with current input type. ■ MODEL NO. Confirm Model No. marking on the product to be exactly what you ordered. ■ INSTRUCTION MANUAL This manual describes necessary points of caution when you use this product, including installation, connection and basic maintenance procedures. POINTS OF CAUTION ■ CONFORMITY WITH EU DIRECTIVES • This equipment is suitable for Pollution Degree 2, Meas- urement Category II (output, transient voltage 2500V) and Installation Category II (transient voltage 2500V). Reinforced insulation (signal input or output to power in- put: 300V) and basic insulation (signal input to output: 300V) are maintained. Prior to installation, check that the insulation class of this unit satisfies the system re- quirements. • Altitude up to 2000 meters. • The equipment must be mounted inside a panel. • The equipment must be installed such that appropriate clearance and creepage distances are maintained to con- form to CE requirements. Failure to observe these re- quirements may invalidate the CE conformance. • The actual installation environments such as panel con- figurations, connected devices, connected wires, may af- fect the protection level of this unit when it is integrated in a panel system. The user may have to review the CE requirements in regard to the whole system and employ additional protective measures to ensure the CE conform- ity. • Install lightning surge protectors for those wires connect- ed to remote locations. ■ POWER INPUT RATING & OPERATIONAL RANGE • Locate the power input rating marked on the product and confirm its operational range as indicated below: AC power: Rating ±10%, 50/60 ±2 Hz, approx. 2VA DC power: Rating ±10%, approx. 2W ■ GENERAL PRECAUTIONS • Before you remove the unit from its base socket or mount it, turn off the power supply and input signal for safety. ■ ENVIRONMENT • Indoor use. • When heavy dust or metal particles are present in the air, install the unit inside proper housing with sufficient ventilation. • Do not install the unit where it is subjected to continuous vibration. Do not subject the unit to physical impact. • Environmental temperature must be within -5 to +55°C (23 to 131°F) with relative humidity within 30 to 90% RH in order to ensure adequate life span and operation. ■ WIRING • Do not install cables close to noise sources (relay drive cable, high frequency line, etc.). • Do not bind these cables together with those in which noises are present. Do not install them in the same duct. ■ AND .... • The unit is designed to function as soon as power is sup- plied, however, a warm up for 10 minutes is required for satisfying complete performance described in the data sheet. COMPONENT IDENTIFICATION Body Base Socket x10 HI SET. (%) X1 x10 LO SET. (%) X1 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 K•UNIT Specifications Input Resistor ■ FRONT PANEL CONFIGURATION Lo LED Lo Setpoint Rotary Switch (×1%) Lo Setpoint Rotary Switch (×10%) Hi Setpoint Rotary Switch (×1%) Hi Setpoint Rotary Switch (×10%) Hi LED HI SET [%] x1 x10 LO SET [%] x1 x10 • Explanations Hi and Lo setpoint rotary switches are used to set the alarm setpoints. The Hi and Lo LED, turn on when the coil for each relay is energized. • Examples For setting the relay to trip above 80% of the full-scale input signal, set the Hi rotary switch (×10) to “8”, while the switch (×1) to “0”. DC ALARM (CE, rotary switch adjustment) MODEL KSL2 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected] EM-3614 Rev.2 P. 1 / 3 INSTRUCTION MANUAL

the unit for separate the body from the base socket. Clamp (top & bottom) DIN Rail 35mm wide Spring Loaded DIN Rail Adaptor Shape and size of the base socket are slightly different with various socket types. ■ DIN RAIL MOUNTING Set the base socket so that its DIN rail adaptor is at the bot- tom. Hang the upper hook at the rear side of base socket on the DIN rail and push in the lower. When removing the socket, push down the DIN rail adaptor utilizing a minus screwdriver and pull. ■ WALL MOUNTING Refer to “EXTERNAL DI- MENSIONS.” TERMINAL CONNECTIONS Connect the unit as in the diagram below or refer to the connection diagram on the front of the unit. When an input resistor is provided with the module, attach it together with input wiring to the input screw terminals. ■ EXTERNAL DIMENSIONS unit: mm (inch) 80 (3.15) 50 (1.97) 72 (2.83) [3.3 (.13)] 80 (3.15) 20 (.79) 60 (2.36) 72 (2.83) 7.8 (.31) CLAMP (top & bottom) DIN RAIL 35mm wide 2–4.5 (.18) dia. MTG HOLE 25 (.98) deep 14–M3.5 SCREW • When mounting, no extra space is needed between units. 12 5 6 14 11 1 10 15 4 3 2 7 9 8 103 (4.06) 132 (5.20) ■ CONNECTION DIAGRAM + – INPUT 4 12 R V(–) 7 14 POWER *Input shunt resistor attached for current input. * U(+) 11 1 10 15 9 2 N.C. HI OUTPUT N.O. COM N.C. LO OUTPUT N.O. COM ■ TERMINAL ASSIGNMENTS unit: mm (inch) Input shunt resistor attached for current input. 5 6 14 11 1 10 15 3 2 7 9 8 INPUT RESISTOR (model: REM) 12 4 12 (.47) KSL2 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected] EM-3614 Rev.2 P. 2 / 3

nected according to the connection diagram. 2) Power input voltage: Check voltage across the terminal 7 – 14 with a multimeter. 3) Input: Check that the input signal is within 0 – 100% of the full-scale. 4) Alarm operations: Check the alarm operations referring to the figure below. 5) Output load: Check that the output load is 380V AC/120VA or 125V DC/30W at the maximum (≤ 0.5A). For maximum relay life with inductive load, external pro- tection is recommended. Alarm Trip Operation Terminal No. in parentheses Trip Operation in Power Failure : Terminals 1 – 2, 9 – 10 turn ON. 0 50 100 Input (%) Lo Setpoint Hi Setpoint Hi Output (9–15)ON Lo Output (1–2)ON (1–11)ON (9–10)ON MAINTENANCE Regular calibration procedure is explained below: ■ CALIBRATION Warm up the unit for at least 10 minutes. • Hi Setpoint Increase the input signal from a value lower than the set- point and check that the trip point remains within the accuracy described in the data sheet. • Lo Setpoint Decrease the input signal from a value higher than the setpoint and check that the trip point remains within the accuracy described in the data sheet. When the setpoints are shifted, please contact M-System’s Sales Office or representatives. LIGHTNING SURGE PROTECTION M-System offers a series of lightning surge protector for protection against induced lightning surges. Please contact M-System to choose appropriate models. KSL2 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected] EM-3614 Rev.2 P. 3 / 3