D-Link DI-704P Quick Installation Manual

any current Web browser, i.e., Internet Explorer or Netscape Navigator. DI-704P Ethernet Broadband Router and Print Server 5V DC Power Adapter ©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice. DI-704P. 08122003 Before You Begin 1. If you purchased this router to share your high-speed Internet connection with other computers, you must have either an Ethernet-based Cable or DSL modem with an established Internet account from an Internet Service Provider (ISP). 2. It’s best to use the same computer that is connected to your modem for configuring the DI-704P Broadband Router. The DI-704P acts as a DHCP server and will assign all the necessary IP address information on your network. See Appendix at the end of this Quick Installation Guide or the Manual on the CD-ROM for setting each network adapter to automatically obtain an IP address. Check Your Package Contents DI-704P Ethernet Broadband Router CD-ROM (containing Manual, Warranty and Print Server Software for Windows) Ethernet (Straight Through) Cable Using a power supply with a different voltage rating will damage and void the warranty of this product. If any of the above items are missing, please contact your reseller.

Router To Your Network B. WAN Port This is for the connection of an Ethernet cable to the Cable or DSL modem C. LAN Ports These are the connections for Ethernet cables to Ethernet enabled computers. D. Printer Port You can connect a Printer to the Parallel Port here. A. Receptor for Power Adapter. Reset Button Pressing this button restores the Router to its original factory default settings. A. First, connect the power adapter to the receptor at the back panel of the DI-704P and then plug the other end of the power adapter to a wall outlet or power strip. The Power LED will turn ON to indicate proper operation. B. 1. Power off your Cable or DSL modem; some devices may not have a on/off switch and will require you to unplug the power adapter. Now, the DI-704P should be powered on and the Cable / DSL modem should be turned off. 2. Cable / DSL modem (Power Off) – DI-704P (Power On) Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL modem. After the Ethernet cable is securely connected, power on the Cable / DSL modem by turning on the unit or plugging in the power adapter. 3. Cable / DSL modem (Power On) – DI-704P (Power On) Insert the other end of the Ethernet cable to the WAN PORT on the back panel of the DI-704P. The WAN LED light will illuminate to indicate proper connection. If the WAN LED is not illuminated, please go back to step B1 and repeat the instructions. C. Insert an Ethernet cable to LAN port 1 on the back panel of the DI-704P and an available Ethernet port on the network adapter in the computer you will use to configure the DI-704P. The LED light for LAN Port 1 will illuminate to indicate proper connection. (Note: The LAN Ports on the DI-704P are Auto-MDI/MDIX. Meaning you can use a straight-through or crossover-Ethernet cable to the LAN Ports.) D. The parallel port on the DI-704P is used to connect printers only. Connect one end of the printer cable to your printer and the other end to the DI-704P.

Connecting Additional Computers To The DI-704P Using additional Ethernet (CAT5 UTP) cables, connect your Ethernet-equipped computers to the remaining Ethernet LAN ports on the back panel of the DI-704P WAN LED – a solid light indicates connection on the WAN port. This LED blinks during data transmission. LOCAL NETWORK LEDs – a solid light on the port indicates a connection to an Ethernet enabled computer on ports 1-4. This LED blinks during data transmission. POWER LED – a solid light indicates a proper connection to the power supply. M1 LED – will flash consistently to indicate that the DI-704P is working properly. M2 LED – a solid light indicates that Internet connection has been established.

Guide, your connected network should look similar to this: Using The Setup Wizard The logon pop-up screen will appear. Open your Web browser and type “http://192.168.0.1” into the URL address box. Then press the Enter or Return key. Type “admin” for the username and leave the password field blank. Click OK

Once you have logged in, the Home screen will appear. You will see the following screens Set up your new password. You have the option to establish a password. Click Run Wizard Click Next Click Next

Select your Internet Connection. You will be prompted to select the type of Internet connection for your router. If you are unsure of which setting to select, please contact your Internet Service Provider. If you selected Dynamic IP Address, this screen will appear: (Used mainly for Cable Internet service.) Click the “Clone MAC Address” button to automatically copy the MAC address of the network adapter in your computer. You can also manually type in the MAC address. Click Next This setup should be done on the computer that is registered on the ISP’s network. Choose your time zone from the drop down list. Click Next Click Next

If your ISP requires a Static IP Address, and this option is selected, then this screen will appear: If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet), and this option is selected, then this screen will appear: (Used mainly for DSL Internet service.) Enter the IP address information originally provided to you by your ISP. You will need to complete all the required fields. Please be sure to remove any existing PPPoE client software installed on your computers. Enter in the username and password provided to you by your ISP. Click Next Click Next

Click Restart Test Internet Connection. You will be returned to the Home tab. For additional settings or information, refer to the Advanced, Tools, or Status tabs on the web- management interface; or to the Manual located on the CD. Then relaunch your Web browser (i.e., Internet Explorer or Netscape Navigator), to link to your favorite Web site to test your Internet connection. Click to Exit

CD-ROM drive. The following window will be shown automatically. If it is not, please run “autorun.exe” on the CD- ROM. Installing the Print Server Software Wait until the following Welcome dialog appears. Select the destination folder. Click Next Click Install Windows Printer Software Click Next Select your Windows operating system

Installing the Print Server Software (continued) Configuring on Windows 98se/Me Platforms After you finish the software installation procedure, your computer will be capable of network printing provided by the DI-704P. On a Windows 95/98 platform, open the Printers window in the My Computer menu. Now, you can configure the print server of the DI-704P: Find out the corresponding icon of your printer, for example, the HP LaserJet 6L. Right click on that icon, and then select Properties. The following screen appears: When the following window is displayed. Click Finish Click OK Then, the setup program will begin to install the programs into the destination folder.

attached at the Print To item. Be sure that the Printer Driver item is configured to the correct driver of your printer. Type in the IP address of the DI-704P. Configuring on Windows 2000/XP Platforms The configuration procedure for a Windows 2000/XP platform is similar to that of Windows 95/98 except the screen of printer Properties: Click Port Click Configure Port Type in the IP address of the DI-704P. Configuring on Windows 98se/Me Platforms (continued) Click on the Details tab Click Port Settings Click OK Click OK (Note: Screen shots are taken in Windows 2000, similar screens will appear in Windows XP.)

the network adapter in your computer is configured properly. Here’s how to configure the network adapter to obtain an IP address automatically for the DI-704P Broadband Router. APPENDIX (continued) Click Internet Protocol (TCP/IP) Click Properties Select Obtain an IP address automatically Restart your computer Click OK For Microsoft Windows XP: Go to Start > right click on My Network Places > select Properties > Right click on the Network Connection associated with the Ethernet adapter and select Properties (i.e., D-Link DFE-530TX+).

The IP address information, the Subnet Mask, the Router’s IP address and the Ethernet adapter address will appear Select Built-in Ethernet in the show pull down menu Click on Network Click on Apply Now Select Using DHCP in the Configure pull down menu Go to the Apple Menu Click on System Preferences and Select Network

D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone. Tech Support for customers within the United States: D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week. D-Link Technical Support over the Internet: http://support.dlink.com email:[email protected] Tech Support for customers within Canada: D-Link Technical Support over the Telephone: (800) 361-5265 Monday to Friday 8:30am to 9:00pm EST D-Link Technical Support over the Internet: http://support.dlink.ca email:[email protected]