AVProEdge AC-DA210-HDBT Quick Start Manual

ac-da210-hdbt Quick Start Guide AVProEdge’s 2x10 HDBaseT Distribution Amplifier offers full 18Gbps distribution to multiple displays using the unit’s two HDMI outputs and eight HDBaseT outputs. This is ideal for bars, restaurants, digital signage, or anywhere you would like to watch one source on multiple displays. If distribution for more than 10 displays is needed, multiple units can be daisy-chained together via the HDMI output ports. This Quick Start Guide will walk you through the installation and configuration of the AC-DA210-HDBT. We will cover: • Installation • EDID Management • Audio Extraction • IR Extension INSTALLATION 1. Connect the HDMI input sources to the AC-DA210-HDBT. 2. Connect the HDMI output devices to the AC-DA210-HDBT with an HDMI cable. 3. Connect the HDBaseT Receivers to the HDBaseT Outputs using Category Cable (T568B Terminated Cat 6 UTP/STP Recommended). Compatible receivers from AVPro are the AC-EX70- UHD-R & AC-EX70-444-RNE. 4. Power on the sources. 5. Connect the power supply into the AC-DA210-HDBT. 6. Turn on output devices/displays. 7. You may now use the front panel button to switch the distribution amplifier’s input • RS232 Extension • USB Connection • Troubleshooting

default IP (192.168.1.239) to connect to a full control system. AVPro Edge’s WebOS is designed with mobile devices in mind, so feel free to use you phone or tablet for real-time control. EDID Management: Setting and managing EDID is very easy, just follow the steps below. EDID management will ensure you get the signal you want from any source connected. Steps to Setting EDID 1. Switch the AC-DA210-HDBT to the input you would like to manage. 2. Hold the Input Select Button for 5 Seconds, all output lights will flash. 3. Looking at HDBaseT output lights 3-8, quick press the Input Select Button to cycle through EDIDs - (Refer to figure below) 4. Once the output lights match the desired EDID, hold the Input Select Button for 5 seconds to set EDID, HDMI input lights will flash Available EDID options are listed below. Additionally, you can copy an EDID from a display: Audio Extraction: Extracting digital audio via this unit’s Toslink or SPDIF (via Coax) or balanced analog using the 3 pin phoenix output ports is easy. You can use these audio ports to distribute audio signals to an AVR or Multi-zone Amplifier. 1. 1080P_2CH 000000 2. 1080P_6CH 000001 3. 1080P_8CH 000010 4. 1080P_3D_2CH 000011 5. 1080P_3D_6CH 000100 6. 1080P_3D_8CH 000101 7. 4K30HZ_3D_2CH 000110 8. 4K30HZ_3D_6CH 000111 9. 4K30HZ_3D_8CH 001000 10. 4K60HzY420_3D_2CH 001001 11. 4K60HzY420_3D_6CH 001010 12. 4K60HzY420_3D_8CH 001011 13. 4K60HZ_3D_2CH 001100 14. 4K60HZ_3D_6CH 001101 15. 4K60HZ_3D_8Ch 001110 16. 1080P_2CH_HDR 001111 17. 1080P_6CH_HDR 010000 18. 1080P_8CH_HDR 010001 19. 1080P_3D_2CH_HDR 010010 20. 1080P_3D_6CH_HDR 010011 21. 1080P_3D_8CH_HDR 010100 22. 4K30HZ_3D_2CH_HDR 010101 23. 4K30HZ_3D_6CH_HDR 010110 24. 4K30HZ_3D_8CH_HDR 010111 25. 4K60HzY420_3D_2CH_HDR 011000 26. 4K60HzY420_3D_6CH_HDR 011001 27. 4K60HzY420_3D_8CH_HDR 011010 28. 4K60HZ_3D_2CH_HDR 011011 29. 4K60HZ_3D_6CH_HDR 011100 30. 4K60HZ_3D_8CH_HDR 011101 31. User EDID 1 011110 32. User EDID 2 011111 33. User EDID 3 100000 34. Copy from HDMI Out1 100001 35. Copy From HDMI Out2 100010 36. Copy from HDBT Out1 100011 37. Copy from HDBT Out2 100100 38. Copy from HDBT Out3 100101 39. Copy from HDBT Out4 100110 40. Copy from HDBT Out5 100111 41. Copy from HDBT Out6 101000 42. Copy from HDBT Out7 101001 43. Copy from HDBT Out8 101010

1. Locate the “AUDIO OUT” connections on the side of the AC-DA210-HDBT 2. Connect the appropriate cable type to the “AUDIO OUT” port 3. Connect the other end of the cable to the input of an AVR or Multi-zone Amplifier IR Extension: The AC-DA210-HDBT can extend IR signals bi-directionally using HDBaseT allowing for signals to be sent to and from the display. IR IN: Choose IR Receiver Type using the dipswitch located on the back of the DA. IR broadcasts to all HDBaseT Outputs. • I-Pass: IR Direct from a Control System • IR Eye: Receive IR using an IR Receiving Eye IR OUT: Emits IR signals sent back through HDBaseT RS-232 Control: In order to connect your computer to the switch by RS-232 you need to make your own cable with one end a phoenix connector and the other end RS-232. If your computer doesn’t have a RS-232 input, get a USB converter (as shown below), and plug the USB end into any computer. Connect the RS-232 3 Pin Phoenix to the Matrix RS-232 Input. RS-232 can be extended over HDBaseT as well. Commands can be passed through the Matrix RS-232 input or use the HDBaseT 3 Pin Phoenix to broadcast directly to your HDBaseT Outputs. USB Connection: Used for firmware updates or control. For a full list of the commands please see the owner’s manual.

Don’t hesitate to contact us! SUPPORT: +1 605-274-6055 USA TOLL FREE: 877-886-5112 EMAIL: [email protected] Troubleshooting: Having problems? Here are some general troubleshooting tips that may help: 1. Be sure that all of the HDMI cables in a 4k/HDR system are rated for 18Gbps. 2. Ensure displays are as capable as EDID selected. 3. If using short HDMI cables (.5m, 1m) try a longer cable. Some short HDMI cables do not sync well. 4. No Signal from HDBaseT runs? Verify category termination and HDBaseT Light Status. 5. Getting no picture or sound? Power down the entire system. Power it back up starting with the display first and work your way back to the source. 6. If you are still having issues after troubleshooting, feel free to contact our Tech Support department.