HeroSpeed LongPlus Quick Start Manual

Please read the Quick Start Guide carefully before using the product and keep it. Related tools and documents of product, please download from www.herospeed.net

2. CAMERA DIAGRAM 1. LED Light 2. Microphone 3. 4MP Camera 4. LED Indicator 5. PIR Motion Sensor 6. Back Shell Open Button 7. Threaded Bracket Interface 8. Strong Magnetic Chuck 9. Speaker 10. Power button & Micro USB Port Battery Camera Adhesive Tape USB Cable Screw Set User Guide Mount Bracket 1 2 3 4 5 6 - 1 - 7 8 9

12. TF-card Slot - 2 - 3. BATTERY CHARGING The batteries inside the Battery camera not fully charged in accordance with transportation safety regulations. Please charge the batteries with a USB Cable (5V adapter not included)，and fully charged for 8-10 hours before installation 11 12 LED Indicator Description Solid Blue None Solid Yellow Solid Green Working Sleep/Power Of Charging Charging Finished

5. WI-FI SET UP Download and install the 'LongPlus' app from Google PlayTM or the App StoreTM. The App is also available by scanning the QR codes on the right, using your QR code scanner in your smart phone. NOTE: Google PlayTM is a trademark of Google Inc. App StoreTM is a service mark of Apple Inc. Before you start the Wi-Fi confguration, please note below: 1). The Battery camera works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi. 2). Avoid using special characters or symbols like (@~!#$%^&*..., in your Wi- Fi name or password. 3). Perform the confguration near your Wi-Fi router. - 3 -

Launch the “LongPlus” APP and register an account with your mobile phone number of email ID. Start the Wi-Fi confguration, following the in-App instructions or refering to the following guiding steps. Guiding STEPS: 2.Turn on the camera 4.Select Wi-Fi 3.Voice prompt 5.Input password 8.Connection succeeds 9.Check signal strength 10.Location name 7.Connecting 11.Adding device complete 1.Tap ”+” to add device 1.Add device 6.Scan QR code

After setup, tap on the live view window in the app for a test. Then take your Battery camera outside to the installation spot and run a test there. Make sure the installation spot is covered by strong 2.4 GHz Wi-Fi signal. If the battery camera doesn't work well outside, you may need to move the router closer to the installation spot or invest in a Wi-Fi extender. 7.LIVE VIEW INTERFACE 4 3 7 6 5 9 10 8 - 5 - 11 12 13 Return Home page Sharing Settings Video Call Speak Alarm Playback Fullscreen Screenshot Light control 11 12 Gallary 13 SD/HD

8. PLAYBACK If the Micro-SD card is properly installed, you can playback the video clips taken after motion detetion. A 7-days-rolling free cloud storage service is ready for your camera. You can also upgrade your cloud service pack in the settings. Tap to upgrade your cloud recording service pack and enable Smart Ai Motion Detetion area customization. 2 3 4 - 6 - 5 Screenshot Video Quit Live View 1 2 Speak 3 Call 4 5 Playback button

QR Code. 9. SHARE YOUR DEVICE 10. ALARM SETTING When a motion is detected by your camera, you will receive alarm notifcation from the App. You can also enable fashlight alarm and siren alarm to be triggered after motion events. The fashlight alarm and siren alarm can also be triggered manually in the camera settings. - 7 - Setting

anchors, or directly to the wall until the bracket is fxed to the wall. You can also use the provided double-sided tape instead of screws to fx the wall mount on fat surface Attach the camera to the bracket and adjust the angle to cover the surveillance area. Do make sure the camera is within the Wi-Fi range. - 8 - LongPlus App will remind you to charge your camera when the battery is low. Please charge the camera with the provided Micro USB cable and a DC 5V 1.5A phone charger. During charging, the camera's LED indicator is in solid yellow, and when the camera is fully charged, the indicator will turn into solid green. It takes about 8-10 hours to fully charge your camera. NOTE:

12.TECHNICAL PARAMETERS When you connect your camera through the LongPlus App, it will prompt you if the latest frmware is available. You can also manually check the frmware upgrade in the settings of the App. Please make sure your camera is fully charged or connected to a power source to upgrade the frmware. Do not cut of the power when upgrading the frmware. Network 2.4 GHz ~ 2.4835 GHz IEEE 802.11 b/g/n Within 3 ~ 4 Sec Software VicoHome iOS, Android Within 2 ~ 4 sec Push notifcation within 2 ~ 4 sec General Video & Audio Storage System 4 Ingenic T31ZX 2560 1440 3

FAQ Q1: How to invite family and friends to use my camera together? A1: Please refer to the guiding steps on page 7 of this user guide. Q2:Why doesn't the Wi-Fi name appear when I connect to Wi-Fi? A2: On Apple devices with iOS13 and above, you need to turn on the "location permission" for the app in the system settings and change it to "allow when using." Q3: Will the camera show red lights when night vision is activated? General

A3:The built-in infrared lamp beads make the camera only show some dim red lights when night vision is activated, but the image quality is still clear under no light environment. Q4:What are the requirements for Wi-Fi? A4:Please use a 2.4GHz wireless network. The device does not support the 5GHz wireless network. Meanwhile, please set the Wi-Fi authentication method to wpa2-psk or other lower level of security method. A password is required. Q5: How far should the camera be placed from the router? A5: After testing, the Wi-Fi connection distance can normally reach up to 150 meters in the open area. However, the actual situation depends on the strength of Wi-Fi and its surrounding environment Q6: What is the maximum length of recording time? A6: You can choose the recording time in the app. The camera can record for a fxed time or “auto” mode, which depending on whether there is a person. The maximum length of a video is 3 minutes. Q7: How to quickly view videos by category? 7A: Click the icon in the upper left corner of the "Library" page to start the search flters. Select the search settings and then click save to view the video playback. Q8: What should I do when the device is in malfunction? A8: Long press the power button to restart the camera.If there is no response, you can open the back shell of the camera, and then open the rubber plug on the side then press the reset button with a pointed object to force the power of, then long press the power button to restart the camera.