Flashforge Adventurer 4 Operation & User’s Manual

User Guide EN/CN-A01 中文P28 本手册仅适用于闪铸科技 冒险家4 3D打印机 This guide is only applicable to FLASHFORGE Adventurer 4 3D printer

1.1 - Component Introduction 1.2 - Packing Specification Chapter 2 Introduction of User Interface 2.1 - Build 2.2 - Prepare 2.2.1 - Preheat 2.2.2 - Filament 2.3 - Settings 2.4 - Maintain 2.4.1 - Upgrade 2.4.2 - Log 2.4.3 - Calibration 2.4.4 - ChangeExtruder 2.4.5 - Maintain Chapter 3 Software Installation Chapter 4 Preparation of Device Chapter 5 Print Chapter 6 Q&A Chapter 7 Support and Service 02 05 06 06 07 08 08 10 10 11 12 13 13 13 14 15 15 16 16 17 21 27 01

safety warnings and notice below. Work Environment Safety Keep your work place tidy. Do not operate Adventurer 4 in the presence of flammable liquids, gases or dust, which will cause fire in the high temperature generated by the equipment. Keep Adventurer 4 out of children and untrained people’s reach. Electrical Safety Always use the Adventurer 4 with a properly grounded outlet. Do not refit Adventurer 4 plug. Ungrounded / improperly grounded / refitted plugs will increase the risk of leakage of electricity. Do not use Adventurer 4 in damp environment or under the burning sun. Damp environment will increase the risk of leakage / exposure to the sun will accelerate the aging of plastic parts. To avoid device damage, please use the power supply provided by Flashforge. Avoid using the device during a thunderstorm. In case of uncertain accident, please unplug the device if you do not use it for long. Personal Safety Do not touch the nozzle and build plate during printing. Do not touch the nozzle and plate after printing to avoid high temperature scald or mechanical damage! Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Do not operate the device while you are tired or under the influence of drugs, alcohol or meditation. Note：Every printer has been tested before leaving factory. It is normal and will not be of trouble if there are filament residue remaining in the extruder or slight scratches on the plate. 02

the left, right and back side space should be at least 20cm, and the distance of the front side space should be at least 35cm. Device storage temperature: RT 0-40℃. It’s recommended to use the filaments offered by Flashforge, or from the brands accepted by Flashforge. Due to the different properties of filaments, you need to modify printing parameters when using those which are not offered by Flashforge. Temperature: RT 15-30℃; moisture: 20%-70%. All polymers degrade with time. Do not unpack filament until necessary. Filament should be stored in clean and dry conditions. Cautions Keep the inside of the device clean and tidy. Do not place metal objects into the chute at the bottom of the platform. Please clean up the remaining in time. It is recommended to operate outside the equipment. Any modifications to the device will invalidate the guarantee. Lower the build plate before loading/unloading filament. The distance between the nozzle and build plate should be kept for at least 50mm. Operate the device in well-ventilated environment. Never use the device for illegal activities. Never use the device to make any food storage vessels. Never put the prints into your mouth. 03

without the official authorization from Flashforge. FLASHFORGE CORPORATION MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: [1] This device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired operation. Flashforge shall not be liable for errors contained herein for incidental consequential damages in connection with furnishing, performance or use of this material. This document contains proprietary information protected by copyright. Copyright © 2021 Flashforge Corp. All Rights Reserved. 04

Positioning Accuracy Layer Resolution Build Volume Nozzle Diameter Build Speed Highest extruder Temperature Filament Support Power Supply Device Size Package Size Software Input/Output File Connectivity Printing Environment Adventurer 4 1 X/Y axis：0.011 mm；Z axis：0.0025 mm 0.1~0.4 mm 220 x 200 x 250 mm 0.4mm (default) 0.6/0.3 mm(optional) 10~150mm/s 265℃/240℃ ABS/PLA/PC/PETG/PLA-CF/ASA/PETG-CF AC100-240V/4.5A,350W 500(L)*470(W)*540(H) mm 585(L)*570(W)*680(H) mm FlashPrint Input: 3MF/STL/OBJ/FPP/BMP/PNG/JPG/JPEG File；Output: GX/G File USB Disk/ WIFI/ Ethernet 15-30℃ Reference 05

5. Filament intake cover 7. Platform base 9. Touch screen 4. Spool holder 1. Power switch 2. Power socket 8. Build plate 6. Front cover 20. Camera 13. Filament guide tube joint 15. Fan for cooling model 11. Ethernet input 12. Extruder 10. USB 16. Fan for cooling extruder 21. Air filter 17. Buckle 18. Air duct 3. Filament cover 19. Nozzle 14. Cable slot 1 2 3 4 5 9 10 7 8 6 11 12 20 13 14 15 16 17 18 19 21 1.1 Component Introduction 06

User Guide Unclogging Pin Tool Power Cable Grease Allen Wrench Filament Guide Tube Joint Leveling Card USB Disk 1.2 Packing Specification 用户使用手册 Adventurer 4 / 冒险家4 User Guide EN/CN-A01 中文P28 本手册仅适用于闪铸科技 冒险家4 3D打印机 This guide is only applicable to FLASHFORGE Adventurer 4 3D printer 07

The interface layout may change whenever there is an upgrade of firmware. The functions below are only for demonstration purposes. 2. File list Tap model file：for file details. Long press model file：multi-selecting mode on. Chapter 2 Introduction of User Interface 2.1 Build Note The finished prints will be marked. Read print file from local memory card Read print file from the USB stick 08

local memory card Amount and type of filaments required Build plate temperature Pause/Resume printing Interface Z：Used when the distance needs to be adjusted between the first printed layer and the extruder. The up and down arrows indicate that the extruder moves upward or downward. Fan：The fan for cooling the model. Wind speed can be adjusted for printing different filaments. Click OK to save and apply the changed parameters. Layer thickness Check more parameter settings and details More Settings You can change filaments The switch of LED light Adjust printing parameters: extruder temperature/ platform temperature/ printing speed 09

Long press to set preheat temperature speedily. Turn ON/OFF the extruder or platform preheat Extruder highest preheat temperature: 265℃（It’s up to the chosen extruder） Platform highest preheat temperature: 110℃ Temperature can be adjusted anytime during heating. 2.2.1 Preheat 2.2 Prepare Prepare Preheat Filament 10

finish loading. Note that fast+slow loading is automatically applied, just place the filament in the extruder gear. Do not push the filament into the tube. You may hear noise when the loading is fast. Change Click on [Change], the extruder will be heated up to the preset temperature. Pull out the filament according to the instruction. Insert new filament in the filament intake until some resistance is felt. New filament coming out of extruder indicates a successful replace- ment. Manual Click on [Manual], extruder will be heated up to preset temperature. Choose filament length, and choose [Load/Unload]. Note that manual mode should be preferred when there is remaining filament in the tube. Note 11

Status, Camera, Brightness, Light, FilamentDetect, Buzzer, PrinterName, About, FactoryReset. Move：to move the extruder left or right, (note that the noise is normal if it moves past the farthest point of the left side), and to move the build plate back and forth, (note that the noise is normal if it moves past the farthest point of the front side); Network：connect device to hot spot/WLAN/Flash Cloud/Polar Cloud； Fan：to turn on/off the fan； Language：select language； Status：including device temperature，X/Y/Z position，etc. 2.3 Settings 12

Light: turn on/off the light on the extruder; FilamentDetect: filament check sensor is on/off; Buzzer: Turn on/off the sounds of device startup and screen click; PrinterName: User can name the device; About: information of this device; FactoryReset: this device is restored to factory setting. 2.4.1 Upgrade When the device is connected to the network, it will be prompted to upgrade when the new firmware is released; 2.4.2 Log When the equipment has abnormal movements, the problem can be fed back to the official after-sales team of Flashforge by copying the log. 2.4 Maintain Camera: Remote monitoring. Turn on the camera during printing, and turn on time-lapse, and time-lapse video can be recorded in the memory disk; it can be found in [Pictures]; choose [Take Pic], the live scene is saved as images; Maintain Upgrade Log Calibration ChangeExtruder Maintain 13

Click on [Normal Mode] to start pre-calibration. The first point is to calibrate the initial distance between the extruder and the platform. Click on the up and down arrows to adjust the Z-axis deviation value. You can also sense if there is slight resistance by pulling A4 paper between them to decide the appropriate distance. In general, no further adjustment is needed. If large size model still cannot be printed after extruder calibra- tion, or failure occurs due to uneven platform, please finish 9-point leveling by calibrat- ing all 9 points. After calibration, the software will automatically calculate a mean value for compensation; when calibrating each point, the user can also adjust the z-axis deviation by clicking the up and down arrows; after compensation, the value can be calculated and applied. 2.4.3 Calibration It is necessary to calibrate the distance between the nozzle and the platform after the first use or replacement of the nozzle; Expert mode：Expert mode is for experienced users to directly calibrate the distance. Click to make extruder move upwards，Click to make extruder move down- wards. 14

temperature the replaced nozzle adopts to; the actual deviation range of the extruder: -10 ~ 30. Click [next] to enter the extruder selection interface. Select the new nozzle to be installed and the maximum temperature during preheating will be set according to the selected nozzle. Please ensure that the installed nozzle is the same as the selected nozzle type, and click [Complete] to return to the maintenance interface. if a different nozzle is replaced, the default maximum temperature of preheating will change to the temperature of the replaced nozzle. 2.4.4 ChangeExtruder In case of errors or unclear operation, please check and operate according to the maintenance suggestions first. 2.4.5 Maintain Note 15

delivery, but due to transportation or other influences, the distance between nozzle and platform may change. It is recommended to conduct [Calibration] after unpacking. This step is optional, please refer to the interface function introduction before operation. Find the FlashPrint installation package in the USB disk and select the version corresponding to your system to install. Or you can download it from https://www.flashforge.com/download-center. Chapter 3 Software Installation Chapter 4 Preparation of Device 16

Chapter 5 Print Connect cable to printer; turn on the switch, the screen lights up. Power Switch 2. Load Filament: open the filament cover on the right side, insert the filament into the filament intake, push filament into the feeding wheel until some resistance is felt. Please make sure filaments are in the feeding wheel. Tap [Prepare]-[Filament]-[Load]. Follow the instruction, filament coming out of the nozzle indicates a success. 17

printing automatically. Method 2: USB Device Files can be read in USB disk. Insert USB disk and select the files to print. 3.Model File Transfer Method 1: Wi-Fi Connection Tap [Settings]-[Network]-[WIFI], operate according to the instruction. Open FlashPrint, click [Print], then click [Machine Type], select [FlashForge Adventurer 4]. You can try to enter the IP address or scan it automatically. The IP address can be viewed in [settings] - [about]. When the user wants to use the browser to view images, the printer and PC must be in an intranet (that is, the printer and PC connect to the same router). IP Address IP Port： 192 . . . : 168 2 122 8899 Auto-scan Connection Connect Note 18

Inquire Polar Cloud PIN code. Turn on the Polar Cloud switch and enter account number and PIN after connecting Adventure 4 to network. FlashCloud Home My Printer My Model My Job Model Library My Printer The current printer is empty, please add a printer Name Registration Code Type Cn + Add Printer （2）Click [My Printer] - [Add Printer]. Fill in the registration number (Registration Code) on page and name the printer. After clicking OK, the information will appear in the FlashCloud interface of the printer. Add Printer Name All fields must be filled in Registration Code OK Cancel Method 3: Cloud FlashCloud （1）Open FlashCloud website (https:cloud.sz3dp.com) to register an account. After the mailbox is activated, you can log in and use it; after logging in. 19

Nozzle and build plate are still hot after finishing printing, please wait for them to cool down before you operate. It is recommended to take the plate to the outside of the equipment for model removal, otherwise the model debris will remain in the equipment. Please keep the inside of the printer clean. Note 20

Q1. How to unclog the nozzle? Q2. How to replace the nozzle? Buckle Method1： Method2： Method3： Tap [Preheat], heat up the nozzle to the set temperature. Once completing heating, press the filament guide tube joint and pull out the filament guide tube. Check to see whether the filament is bent or filament’s cross-section is smooth. If not, cut it smooth, install the guide tube and filament back. Tap [Load]. If method 1 does not work out, use an unclogging pin tool to unclog filament. If method 1&2 do not work out, please replace the nozzle. Press the left and right clips and pull out the nozzle. Push in the filament through the filament intake manually, making it long enough to be cut off; Rotate the filament spool anti-clockwise manually, making filament retreat a little; Press the left and right clips, install the new nozzle. Make sure nozzle slot and bottom of extruder are on the same level. Tap [Prepare] -- [Load], filament coming out of the new nozzle indicates successful replacement. 1. 2. 3. 4. 5. Power off before replacing nozzle! No power on operation! Note 21

Yes, small errors may occur because of the calibration. To keep best printing quality, you need to calibrate it again. Q4. What can I do if no filament comes out of the extruder after I choose the file and the extruder moves normally? Q5. How to solve if the distance between nozzle and platform is too large(far away) or too small(that they collide)? Tap[Maintain]--[Calibration]； The printer starts pre-calibrating. The first point is to calibrate the initial distance between the extruder and the platform (see Z-axis deviation value). Click the up and down arrows to adjust the Z-axis deviation value. With the help of the leveling card, you can feel if there is any slight resistance to decide the appropriate distance. When the extruder is still unable to properly print a large size model after calibration, or when the model fails to be printed due to uneven platforms, please continue using this function. The machine will calibrate the remaining 8 points. After calibration is completed, the software will automatically calculate a compensation mean to compensate. When each point is being calibrated, the user can also adjust the Z-axis deviation by clicking the up and down arrows. After compensation is completed, the value is memorized and the extruder goes back to zero. 1. 2. 3. 1. 2. Check the filament guide tube, make sure the filament has been pushed into the extruder; if not, please tap [Load] till filament comes out; check whether the extruder is clogged, if so, please refer to Q1. Whether the extruder assembly is in place is judged as follows: 1.When installed, the extruder must be pushed to the end; 2.Check whether the installation is in place： ①Touch the black buckle and the lower shell of the white extruder, make sure no hollows are felt； ②Observe to make sure there is no large gap in the joint of the black buckle and the lower shell of the white extruder. Improperly installed with seam Properly installed with no seam 22

Heating up the platform can increase adhesion between platform and model. Adding raft to model when slicing in FlashPrint. Apply solid glue to platform before printing. Use extruder calibration in expert mode or leveling calibration to reduce the distance between the nozzle and the platform. Make sure the platform is flat. Complete 9-point leveling suggested. Apply extruder calibration to reduce the gap. Method1： Method2： Method3： Method4： Method5： Method6： Q6. Can we use other brand filament which is not produced by Flashforge? Q7. Is Adventurer 4 compatible with all kinds of AC power input? Adventurer 4 is equipped with a built-in 24V/13.3A power supplier, suitable for 100V-240V input voltage. Q8. Is Adventurer 4 capable of turning itself off automatically after printing job is finished? No . Q9. What kinds of file formats does Adventurer 4 support? Q10. Does Adventurer 4 support other cloud platforms besides FlashCloud? Yes, Adventurer 4 interface is open up to all other cloud platforms. Input: 3MF/STL/OBJ/FPP/BMP/PNG/JPG/JPEG Files. Output: GX/G files. Q11. Is the ABS printing safe? ABS filament will give off certain poisonous gas when heated up, please put the printer in well-ventilated condition when printing ABS. We suggest using non-toxic PLA filament when printer is near children. Adventurer 4 supports ABS, PLA, PC, PETG, PLA-CF, PETG-CF, etc., which have different ingredients. Adventurer 4 tests out default settings like temperature and filament output to ensure the best printing quality. Other brands of filaments can be used with the parameters adjusted. Because the required temperature between different materials is slightly different, it is recommended to clean the previous filaments before using new filaments, otherwise it is easy to cause extruder blockage. 23

is 300℃, and the fan is also working. Why is this happening? Power off when replacing the nozzle. Q15. The extruder makes out chug noise and no filament comes out of the extruder, what is the problem and how to solve? Load: only load filament into the extruder； Change:first unloading and then loading filament, from fast to slow; Manual: slow loading. Q16. What is the difference between filament loading, filament replacement and manual mode? Calibrate the printer again or finish Homing again before giving it another go. Q17. Adventurer 4 starts printing when the distance between extruder and build plate is still large, causing filament unable to stick to plate. USB driver file is not correct. Adventurer 4 only supports FAT32 file system, please format USB driver into FAT32 file system. Q18. Printing files cannot be found when using USB driver? Note: Note that the temperature setting in the slicer file might not match the highest temperature of the replaced nozzle. Errors: Errors in temperature displaying indicate that the new nozzle is not properly installed, and the extruder temperature cannot be read by the sensor. Please plug out and install the extruder again, make sure that the extruder is pushed to the end, and the buckle and bottom of extruder are on the same level. Refer to Q2. Filament has not loaded into extruder, which is most likely because the extruder is clogged or filament guide tube is not properly installed. Check the guide tube joint first, if it’s normal, refer to Q1 for resolution. it is recommended to use manual mode during testing the nozzle unloading filaments. Not recommended for loading filaments. If it is used, please select the maximum length. Q13. Is it a must to add a raft before printing the model? Not necessarily. More filaments come out of the nozzle when printing the raft, higher success rate there will be. When the plate is heated, the adhesion between the model and the platform increases, which makes the model adhere to the platform well when printing, and also increases the success rate. 24

Pictures can contain up to 10 models, while videos 20 models. The printer adopts fast-slow loading, make sure there is no remaining filament in the guide tube. Q23. Noise in the gear when loading filaments? Open Polar Cloud website, and log in account. https://polar3d.com; Click in Cloud Account on the right top corner, roll down the page to find PIN code; Open Polar Cloud on the printer, enter account number and PIN code; Turn on the switch and connect to Polar Cloud. Set printing parameters in the printer. Note that adjustments might be delayed to take effect, or improper adjustments will affect printing quality, please set it with caution. 1. 2. 3. 4. Q20. How to connect to FlashCloud? Open FlashCloud website: https://cloud.sz3dp.com/login.html; Open FlashCloud interface or about on the printer; Add the printer on FlashCloud website, enter name and registration code of printer; Turn on the FlashCloud switch to connect the printer. 1. 2. 3. 4. Q21. How to use camera? Turn on camera to watch live video on the Cloud； Time-lapse function will take 100 pictures during printing and makes a video. 1. 2. In expert mode, the distance can be adjusted directly for experienced users. Details can be found in the calibration instructions for expert mode. Q24. What is expert mode in calibration? Q25. How to set printing parameters during printing? Pay attention to the distance when it moves along the side to avoid hitting the border. Q22. Operation of movement When the length is not selected, press the button to start the movement, and release the button to stop the movement; When the length is selected, press to start the movement, release will not stop the movement until the corresponding length is reached. 1. 2. Note Note 25

Q26. Wi-Fi connection failure? Please check if there are any special characters in the Wi-Fi hotspot name, if there are any, please modify them and try again; Check your password for special characters, and if so, try again after you have modified it. 1. 2. Q27. Firmware update Please do not disconnect the network during download or update to prevent update failure. Q28. Turn on the printer with white screen and no firmware If you hear the power-on sound, change the screen or the wiring; If you cannot hear the power-on sound, please contact the supplier. When the printer is not used for a long time, apply grease on the guide rail, do it regularly every other month. Put filaments in the drying box to prevent moisture. If it is used frequently, it is recommended to replace HEPA filter cotton once every 2 weeks. Replace as follows: 1. 2. Daily Maintenance Instructions: 2.Open the air filter cover, put in a new cotton filter, and close the filter cover. 1.Open the front door of printer, and find the air filter device indicated in the picture. Note 26

S/N: FFAD****** Flashforge team is on standby and ready to help you with any challenges you may have with your 3D printer. If the issues or questions are not covered in this User Guide, you can seek for solutions on our official website or contact us via telephone. There are solutions and instructions to common issues that can be found in our knowledge base. Have a look first as most basic questions are answered there. http://www.flashforge.com The Flashforge support team can be reached by e-mail or phone between the working hours of 8:00 a.m. to 5:00 p.m. PST Monday through Saturday. In case you contact us during off-duty time, your inquiry will be answered the following business day. Note: Because of changing different filament the extruder maybe blockaded. It’s not owing to quality issue, and outside the scope of 400 hours life. If users encounter this problem, please contact our after-sale department and finish clean work according to their instruction. Facebook Official Group Address: Flashforge Official User Group Email：support@flashforge.com Address: No.518 XianYuan Road, Jinhua City,Zhejiang Province, China 27 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

1.2 - 装箱清单 第二章 设备操控界面简介 2.1 - 打印 2.2 - 准备 2.2.1 - 预热 2.2.2 - 丝料 2.3 - 设置 2.4 - 维护 2.4.1 - 在线升级 2.4.2 - 日志 2.4.3 - 喷头校准 2.4.4 - 喷头更换 2.4.5 - 维护建议 第三章 软件安装 第四章 设备预准备 第五章 首次打印 第六章 Q&A 第七章 帮助与支持 29 31 32 32 33 34 34 36 36 37 38 39 39 39 39 40 41 41 41 42 46 51 28

风险。 请勿将设备暴露在潮湿或烈日的环境中。潮湿的环境会增加漏电的风险 / 暴晒会加速塑件老 化。 请勿滥用电源线，务必使用闪铸科技提供的电源线。 切勿在雷雨天气使用设备。 如长时间不使用设备，请关闭设备并拔下电源线插头。 个人操作安全 在设备运行时，请勿触碰喷头、平台等位置！ 在打印完成时，请勿触碰喷头、平台，以免高温烫伤或机械损伤！ 在操作设备时，请勿穿戴围巾、口罩、手套、珠宝装饰等容易卷入设备的物件！ 请勿在饮酒、服药之后操作设备！ 设备使用提示 保持设备内部整洁，切勿将金属物体掉入打印平台底部的滑槽内。 请及时清理丝料碎屑，建议在设备外进行操作。 自行对该设备进行任何改装将自动失去保修保障。 请在设备进丝操作时，喷头和平台的距离至少保持50mm的距离。距离过近可能会造成喷头 堵塞。 请在通风的环境下操作设备。 请勿利用该设备进行违法犯罪的活动。 请勿利用该设备制作食物储存类产品。 请勿将打印模型放入口腔。 注意：每台3D打印机在出厂前都经过打印测试，若设备喷头存在耗材残留或打印平台有轻微划 痕，都属正常现象，不影响使用。 29

30

0.1~0.4 mm 220 x 200 x 250 mm 0.4mm （默认）0.6/0.3 mm（可选） 10~150mm/s 265℃/240℃ ABS/ PLA/ PC/ PETG/ PLA-CF/ ASA/ PETG-CF AC100-240V/4.5A，350W 500（L）*470（W）*540（H） mm 585（L）*570（W）*680（H）mm FlashPrint 输入：3MF/STL/OBJ/FPP/BMP/PNG/JPG/JPEG文件；输出：GX/G文件 U盘/ 无线网/ 以太网 15-30℃ 设备参数 31

第一章 设备简介 5. 送丝盖板 7. 平台底座 9. 触控屏 4. 料盘架 1. 电源开关 2. 电源插座 8. 平台板 6. 前门 20. 摄像头 13.气管接头 15. 模型冷却风扇 11. 网口 12. 喷头 10. USB 16. 喷头冷却风扇 21. 空气过滤 17. 卡扣 18. 导风嘴 3. 丝盘门 19. 喷嘴 14. 排线槽 1 2 3 4 5 9 10 7 8 6 11 12 20 13 14 15 16 17 18 19 21 1.1 整机介绍 32

www.sz3dp.com CN/EN-A01 冒险家4 用户使用手册 33

1. 在首页点击打印图标，选择读取打印文件的路径。 从打印机本地存储卡中读取 从外接U盘中读取打印文件 固件不定期升级，界面请以实际显示页面为准。以下仅为功能简介。 2. 文件列表 点击任一模型文件：进入文件详情页面； 长按任一模型文件：开启多选模式。 第二章 设备操控界面简介 2.1 打印 注意事项 打印完成的模型会进行标记 34

文件详情 喷头温度 打印时长 打印速度 将文件复制到本地存储卡中 耗材所需总量及名称 层厚度 加热平台温度 暂停打印/恢复打印 打印界面 Z：Z轴补偿，若打印第一层平台与喷头间距不适合，可点击进行调整。向上箭头表示喷 头向上移动，向下箭头表示喷头向下。 风扇：可调节喷头的模型冷却风扇，可调节风速以适应不同材料打印。 点击确定按钮，所改动的参数被保存并应用。 更多设置 可进行换丝 照明灯的开/关 调整打印参数：可修改喷头温度/ 平台温度/打印速度 弹出更多弹窗，可进行参数调节 35

点击 可设定预热温度值； 长按 温度值快速调整。 点击开始，启动预热；点击取消，预热结束。 喷头最高温度：265℃（可设置最高温度实际依据喷头选择而定） 加热平台最高可设置温度：110℃ 加热过程中可随时调节温度。 2.2.1 预热 2.2 准备 准备界面 预热 丝料 36

2.2.2 丝料 丝料包含进丝/换丝/手动 进丝 点击进丝后，喷头将加热到所设置的温度；根据界面提示来完成进丝操作。需注意自动模式时采取 快速+慢速进丝模式，只需将丝料放置在送丝轮处。自动模式切勿将丝料推到导丝管内部。进丝太 快容易引起异响。 换丝 点击换丝后，喷头将加热到所设置的温度；根据界面提示抽出丝料；将新丝料放入进丝口，感受到 阻力即可；当喷头出丝时表明换丝完成。 手动 点击手动后，喷头将加热到所设置的温度；选择对应长度后，选择进/退丝。 若导丝管内有丝料，建议使用手动模式操作；一般建议使用自动模式。 注意事项 37

设置包含移动、网络、风扇、语言、状态、相机、亮度、灯、丝料检测、声音、命名设备、关于、 恢复出厂。 移动：移动喷头左右移动、平台前后移动；注意喷头若移动超出到最左边运动量程会发出异响 为正常现象；平台移动到最前面超出运动量程后，发出异响为正常现象。 网络：可连接设备热点/无线网络/闪铸云/Polar云； 风扇：可控制腔体风扇开/关； 语言：根据地区选择合适的语言； 状态：显示设备温度，坐标等； 相机：可进行远程查看； 开启摄像头，开启延时视频时，在打印过程中将会录制延时视频，存 储在内存中；可在图片中查询。点击拍照，将会拍摄当前画面以照片形式存储。 亮度：调节屏幕亮度； 灯：喷头灯开/关； 丝料检测：开关丝料检测传感器； 声音：开关设备开机启动 声音以及屏幕点击的声音； 命名设备：用户可自定义命名设备； 关于：设备的信息； 恢复出厂：恢复原始出厂的信息。 2.3 设置 38

2.4 维护 维护 在线升级 日志 喷头校准 喷头更换 日常维护 39

普通模式：包含了喷头校准以及9点调平补偿功能 用户点击校准后，机器开始预校准，第一个点为校准喷头与平台间的初始距离，点击上下箭头可调 节Z轴偏差值；在喷嘴与平台之间插入调平卡，来回抽动查看是否有略微的摩擦阻力，如有，即为 合适距离。一般情况下可以不继续调整。当喷头校准后仍无法较好的打印大面积模型，或者打印模 型由于平台不平而导致失败时，请做完整的9点调平操作，校准全部的9个点，校准完成后，软件将 会自动计算一个补偿均值进行补偿；校准每个点时，用户也可自己通过点击上下箭头来调节Z轴偏 差值；补偿完成后，数值被计算应用。 安装新喷嘴后，请根据所换喷嘴的温度值做补偿值设置；喷头实际偏差范围：-10~30。点击下一 步进入选择喷头界面。选择所安装的新喷嘴，预热中会根据选择的喷嘴类型而设定最高温度。请确 保安装的喷嘴与选择的喷嘴类型一致，点击完成回到维护界面。 更换不同的喷嘴，预热的默认最高温度会变为所更换的喷嘴温度。 注意事项 2.4.4 喷头更换 40

第三章 软件安装 第四章 设备预准备 41

1.连接电源。 第五章 首次打印 通过电源线连接电源与打印机； 开启开关，屏幕点亮。 电源开关 2.安装丝料：打开右侧耗材门，将丝料插入进丝口，推入送丝轮内，感受到一定阻力即可。 请务必确认丝料已经推入送丝轮。点击屏幕准备-丝料-进丝。按屏幕指示操作，待喷嘴吐出丝 料说明进丝完成。 42

将stl或obj 文件导入到切片软件中；进行切片，软件切片完成后，打印机进行加温等工作，准 备完成后自动开始打印。 方式二：U盘打印 设备也可通过U盘打印，将切片好的文件保存至U 盘，将U盘插入到设备，选择对应文件点击 打印。 3.传输文件 方式一：传输WiFi 点击设备的设置-网络-WiFi，按屏幕提示连接即可；打开FlashPrint，点击菜单中的打印按 钮，选择冒险家4连接机器；可通过输入IP地址或自动扫描的方式，IP地址可在设备设置-关于 中查看。 打印机连接的网络和电脑连接的 网络必须在同一网段中，否则无 法连接成功。 注意事项 IP地址 IP端口： 192 . . . : 168 2 122 8899 自动扫描 连接机器 连接机器 43

冒险家4 连接网络后打开Polar 云开关，输入账号与PIN码即可。 FlashCloud 首页 我的打印机 我的模型 我的任务 模型库 我的打印机 当前打印机为空，请添加打印机 打印机名称 注册号 类型 En + 添加打印机 （2）点击【我的打印机】- 【添加打印机】。 在添加打印机页面填写注册号（云注册码），为打印机起个名字，点击确定后，这些信息会出 现在打印机的闪铸云界面。 添加打印机 打印机名称 所有字段都必须填写 注册号 确定 取消 方式三：云打印 闪铸云打印 （1）打开闪铸云网站，注册账号，经过邮箱激活后，即可登录使用。 闪铸云：https：cloud.sz3dp.com 44

4.打印后模型移除 直接取出平台柔性钢板，折弯平台即可取下模型。 注意事项 打印完成时，喷嘴和打印平台仍处于高温状态，建议冷却后操作。 模型移除建议将平台板拿到设备外部再进行移除，否则模型碎屑容易留在设备腔体内，建议保 持腔体清洁。 45

第六章 Q&A Q1. 喷嘴堵头怎么办？ Q2. 如何更换喷嘴？ 夹扣 喷头装配是否到位的判断如下： 1.安装必须用力将喷头按压到底； 2.检查是否安装到位： ①用手触摸黑色卡扣与白色喷头下壳无凹陷； ②肉眼观察黑色卡扣与白色喷头下壳接触处无较大间隙。 有缝隙，未安装到位 无缝隙，安装到位 方案1： 方案2： 方案3： 点击预热按钮，将喷嘴温度加热至所用耗材的打印温度，待加温完成，按压气管接口， 拔出导丝管，查看丝料是否弯折，丝料头部是否平整。若不是，剪平整后，将导丝管与 丝料装入喷头，再点击进丝查看。 方案1无改善，则使用通针通丝。 若使用通针通丝仍无法解决堵头问题，请更换喷嘴。 按压住左右扣，同时拔出喷嘴; 在进丝口手动推丝，使其伸出足够长度方便剪断丝料； 手动逆时针转动料盘，使丝料后退一些; 按住左右扣，将新喷嘴插入喷头中，确保喷嘴卡槽位与喷头下部齐平; 点击屏幕中的准备--进丝，直到丝料吐出，喷嘴更换完成。 1. 2. 3. 4. 5. 更换喷嘴前请先关机断电，请勿带电操作。 注意事项 46

支持，冒险家4的开放性接口支持其他云平台。 输入：3MF/STL/OBJ/FPP/BMP/PNG/JPG/JPEG 文件 输出：GX/G文件 Q11. 打印ABS 材料安全吗？ ABS在加热过程中会释放有毒气体，打印时或者打印后可开启HEPA的空气过滤器，但还是建议置放于 开阔空气流通的环境下打印。儿童活动场所建议打印PLA无毒材料。 点击维护--进行喷头校准； 机器开始预校准，第一个点为校准喷头与平台间的初始距离（见Z轴偏差值），点击上下箭 头可调节Z轴偏差值；借助调平卡来回抽动感觉是否有略微的阻力，如有，即为合适距离。 当喷头校准后仍无法较好的打印大面积模型，或者打印模型由于平台不平而导致失败时，请 继续使用该功能，机器会校准其余8点，校准完成后，软件将会自动计算一个补偿均值进行 补偿；校准每个点时，用户也可自己通过点击上下箭头来调节Z轴偏差值；补偿完成后，记 忆数值，喷头回零。 冒险家4支持ABS、PLA、PC、PETG、PLA-CF、PETG-CF等材料，各品牌材料配方略有不同， 冒险家4根据闪铸科技ABS、PLA、PC、PETG、PLA-CF、PETG-CF等材料特性，调试确定最佳 温度、出丝量等默认参数值，确保模型打印质量。其他品牌丝料可以使用但需要经过参数调 整，由于不同材料温度差异略有区别，更换耗材时建议将前一次耗材清理完再使用新耗材，否 则容易引起喷头堵塞。 1. 2. 3. 1. 2. 观察导丝管，确认丝料是否已进入喷头，若无，请再点击进丝按钮，直至丝料从喷头中吐 出； 查看喷头是否堵头，若是，解决方案请查看Q1。 47

Q12. 打印模型发生翘边或粘不牢现象怎么办？ Q13. 打印模型是必须要增加底板吗？ Q14. 更换完喷嘴后的注意事项及更换后状态显示喷头温度300℃，并且喷头上的风扇转是怎么 回事？ 更换喷嘴时请关闭电源。 不一定，打印底板时出丝量较多，打印成功率较高，在底板加热的条件下，模型与平台板的粘 附性增加，使得模型打印时能很好的粘附在平台上，同样也能增加打印成功率。 Q15. 进丝机构发出突突的响声，并且喷头一直不出丝怎么办？ 进丝功能：只包含将丝料送入喷头； 换丝功能：包含进丝与退丝两个功能，先退丝后进丝。先快速送丝，后慢速送丝； 手动功能：采用慢速进丝。 Q16. 进丝、换丝和手动有什么区别？ 请重新校准或者重新回零再打印。 Q17. 选择文件开始打印时，喷头下降到仍与平台有一定悬空距离处就开始打印，导致丝料无 法黏在底板上怎么办？ U盘格式不正确，冒险家4只支持FAT32格式的文件系统，请将U盘格式化成FAT32格式。 Q18. 插入U盘，找不到打印文件，并且全为文件夹怎么办？ 增加平台温度可有效缓解此问题，增加平台与模型的粘附力。 模型切片时选择底板，可有效缓解此问题。 涂抹胶水。 喷嘴与平台的间隙过大，可相应减小间隙，使用喷头校准专家模式或调平校准功能进 行调整。 确认平台是否放平。可使用调平校准功能，建议执行完全流程的9点调平。 使用喷头校准功能减小间隙。 注意事项： 注意切片文件中的温度设置，可能会和切换后的喷嘴最高温度不匹配。 异常情况： 温度显示异常说明喷头传感器没有被读取到，说明喷嘴安装不到位，请重新插拔安装喷头，并 将喷头推到底，确保卡扣处与喷头下方齐平。具体可查看Q2。 进丝机构发出突突的响声，说明丝料无法进入到喷头中，极大可能喷头堵头或导丝管位置安装 不到位。请首先按下导丝管接头检查导丝管连接是否正常。若正常请再参照问题Q1。 手动功能建议在测试喷嘴是否能出丝时使用，不建议当进丝功能使用。如果 当进丝功能使用，请选择最高长度。 方案1： 方案2： 方案3： 方案4： 方案5： 方案6： 注意事项 注意事项 48

Q19. 如何连接Polar云？ 图片能保持10个模型， 视频能保存20个。 机器采用快慢进丝，所以请确保进丝时导丝管中没有剩余丝料。 Q23. 进丝时齿轮异响？ 打开Polar云网址，登陆账号密码。https://polar3d.com； 打开右上角云账户个人信息，往下翻到底查看PIN码； 打开打印机Polar云界面，输入账号和PIN码； 打开Polar云开关，连接Polar云。 进入打印详情界面调整参数，注意调整后可能会延时生效或者调整不合理会影响打印质量，请 慎重设置。 1. 2. 3. 4. Q20. 如何连接Flash云？ 打开闪铸云网址：https://cloud.sz3dp.com/login.html； 打开打印机闪铸云界面或者关于界面； 在闪铸云网址上添加打印机，输入名称和打印机的注册码； 打开打印机的闪铸云开关按钮连接闪铸云。 1. 2. 3. 4. Q21. 如何使用相机功能？ 启用摄像功能，可在云上看到视频； 启用视频延时功能会在打印中截取100张图片保存下来，打印完成后压缩成视频。 1. 2. 专家模式直接调整间隙数值，适合有经验的用户操作,详情可查看校准说明中的专家模式讲解。 Q24. 校准时何为专家模式? Q25. 打印过程中如何调整打印参数？ 靠边运动时注意距离，防止撞击边框。 Q22. 移动中的隐藏小知识 没有选中长度时按下按钮开始运动，松开按钮停止运动； 选中长度时按下开始运动，松开不会停止，一直走到对应长度才会停止。 1. 2. 一定要确定密码输入正确。 Q26. WiFi连接不上怎么办？ 请检查WiFi热点名称是否有特殊字符，如果有请修改之后再次尝试； 请检查密码是否有特殊字符，如果有请修改之后再次尝试。 1. 2. 注意事项 注意事项 注意事项 49

Q27. 更新固件注意事项 请不要在下载或更新的过程中断电断网，防止更新失败。 Q28. 为什么开机屏幕白屏，不显示固件？ 如果听得到开机声音，请更换屏幕或者排线； 如果听不到开机声音，请联系供应商。 当打印机处于长期闲置状态时，请在导轨上涂抹润滑油，或每隔一个月定期涂抹；请将耗材放 在干燥盒中，以免受潮。 若时常打印，建议2周更换一次HEPA 过滤棉； 更换方式： 1. 2. 日常维护说明 2.打开空气过滤盖，将新的滤棉放入，盖上 过滤盖。 1.打开打印机前门，找到空气过滤装置。 如图所示位置。 50

您可以在周一到周六的上午8:00到下午5:00的时间段通过电话和 QQ 来联系闪铸的售后团 队，为您解决问题。如果您刚好在下班时间联系我们，我们将在下个工作日的第一时间给您反 馈，为您解决问题，若造成不便，我们万分抱歉。 提示：由于更换不同的丝料，会有少量杂质残留在喷头中造成喷头堵塞，疏通后即可，不 属于质量问题，不在400小时寿命范围内，若用户使用时存在该问题，请联系售后，并在售后 的指导下完成疏通工作。 售后服务热线：400-8866023 售后客服 QQ： 2850862986 / 2850863000 / 2853382161 3D爱好者QQ群：206773820 公司地址：浙江省金华市婺城区仙源路518号 提示：联系售后时，请提供产品序列号，也就是打印机背部的条形码。 51

Address: No.518 XianYuan Road, Jinhua City,Zhejiang Province, China Service Hotline: +86 579 82273989 support@flashforge.com Follow us