Ampac FIREVIEW Quick Start Manual

TESTER World’s first all in one unified tester for heat and smoke detector. MAN 3141

1 Components 2 Ampac Product Item Numbers Item Number Description 4112-1012 Ampac FireView Portable Fire Detector Tester 4112-1007 Smoke Oil (100ML) 4112-1008 FireView 6M Extension Pole 4112-1009 FireView 10M Extension Pole 4112-1010 FireView Smoke Detector Removal Tool 4112-1011 FireView Heat Detector Removal Tool 4112-1013 FireView Replacement Head Unit

3 Specifications Items Specifications Testable Detector Heat: Rate of Rise Heat Detector, Fixed Temperature Heat Detector Smoke: Ionization Smoke Detector, Photoelectric Smoke Detector Option: Analog Type Detector, Unexploded Type (Heat) Head Size 150mm (Detector Insertion) Inspection Pole Length Minimum Approx. 127cm / Maximum approx. 250cm If longer pole is needed 6m and 10m poles are available upon request. Weight 2.3kg Material Aluminum Input AC100 ~ 240V 50~60Hz 2A Output DC12V 2A Operating Temperature Range Approx. 0°C to 40°C Keeping Temperature Range Approx. -10°C to 40°C Operating Humidity Range Approx. 0% to 85%, No Frost Smoke Generator Ability Approx. 50 testable based on 1.00ml smoke detector Battery 14.8V Li-ION Charging Time Full charge consumes approx. 5 hours Charger Input: AC 100-240V, 50-60Hz, 0.5A / Output: DC 12V2A Running Time Up to 5 hours Duration may vary due to operating conditions; battery has limited recharge cycles and may eventually need to be replaced. Tester Ability (One Time of Charge) Approximately 200 Heat Detectors and 300 Smoke Detectors

4 Controller – Indication & Controls 5 Test Pole Components 6 Battery Charging 1. If the controller does not operate when the LOW LED is lit or the controller’s button is pressed, the battery is discharged. Charge the battery by inserting it into the charging jack with the dedicated charger (DC 12V2A). 2. The CHARGE LED lights up while charging. 3. The charging time is approximately 5 hours. When the charging is complete, the red FULL LED will turn on and the charging will stop. The instrument will not have any problems even if the charging jack is plugged in for a long time. 4. If a different charger (voltage higher than 12V) is used, it may cause a breakdown or fire. Therefore, you must use the dedicated charger (DC 12V2A) supplied with the device.

7 Smoke Oil Fill 1. Remove the wing nut from the smoke oil fill point. 2. Inject 10ml to 20ml of smoke oil, do not over fill as this will produce excessive smoke and lead to extended test times and fan usage. 3. Replace the wing nut ensuring that it is tight. 8 User Instructions 8.1 Paring Instructions 1. To activate pairing mode, press the ‘C’ button on the controller twice to activate the pairing mode blinking Smoke, Heat and Fan LED’s with a beep sound. 2. To cancel the pairing mode, press the ‘C’ button. 3. To complete the pairing mode, press the ‘C’ button on the remote control or the ‘C’ icon on the FireView Smartphone Application. 4. If pairing is successful, LED lights will blink 3 times and make a beep sound. 8.2 Controller Instructions 1. Power up the controller using the ‘Power On’ switch. 2. Locate detector tester rubber gaiter over the detector located on the ceiling, adjust the length of the pole where required. 3. Press either the Heat or Smoke switch according to the detector type under test. 4. Heat and smoke are created in 5 and 3 seconds after the heating element is fully warmed up, respectively. 5. The unit has a built-in fan which can be used to expel smoke from the smoke detector following the activation test. To start the fan, press the ‘D’ button. 6. When heat generation times needs to be extended for fixed temperature detector testing, press the ‘C’ button to extend for approximately 2 minutes. 7. A Smartphone application is also available for Android devices. Please contact your local Ampac Customer Service Office for more information.

WWW.AMPAC.NET UNCONTROLLED DOCUMENT NOTE: Due to AMPAC’s commitment to continuous improvement specifications and information contained within this document may change without notice.