Ametek TR-2000 Operation Manual

35 TR-2100 Connection To make a connection, click on the Connect button. The program will attempt a connection by looking for a CLI command prompt. If this is successful, it will attempt to read the EEPROM chip on the first board of the system. Once the values have been read from the board, the actual input values will start to be displayed. There are two main parts to the calibration process - offset and gain. Offset Adjustment The offset should ALWAYS be adjusted first because it will affect the subsequent accuracy of the gain offset. To set the offset, it is important th ...

49 Digital-only Input Board Jumper Locations Set the Digital-only Input Board configuration jumpers per Table 15. Refer to Error! Reference source not found. for the location of each configuration jumper. Table 15 Board No. Extra Digital Channels DIG BRD SEL 0 DIG BRD SEL 1 1 1-32* On On 2 33-64* Off On 3 64-96* On Off 4 97-128* Off Off * Channel number as reported in Display Station will depend on the number of analogue boards fitted. Figure 13 Digital-only Input Board Jumpers ...

76 Power (fundamental) Apparent f f S V fI = * Real f f f P V I Cos = * * Φ Reactive f f f Q V I Sin = * * Φ For delta VTs real power is computed using the two wattmeter method. Displacement power factor PF Cos = Φ Impedance (fundamental) I V Z f f f = Imbalance mI V V = − + 1 1 100 * % (Ratio of NPS to PPS) Phasor Measurement The TR-2100 acquisition system is organized so that a sample is taken at the second marker. The computed absolute phase angle from a Discrete Fourier Transform (DFT), using a 1 cycle window starting with this sample, will yield the angle of the v ...

54 PC conflict, or a failed port. Please call Technical Support for additional information or help. 14. Now you will perform the following command to format the Hard drive. At the CLI> prompt, type in system formatdisk and press the Enter key. Formatting will take 30 minutes or longer to complete. See the example below. Once the process is complete, a message will appear telling you that the format was successful. Example: CLI>system formatdisk 15. At the CLI> prompt type in the word QUIT and press the enter key. The recorder will respond that it has disconnected. Exi ...

51 Format Procedure 1. Verify that all events at the TR have been retrieved. If not, retrieve them before proceeding. This includes Harmonic Logs, Trend Logs, and the standard TR events. 2. Attach one end of the TR-2100 direct connect cable (AMETEK P/N 1077- 271) to the computer’s unused RS-232 port and the other end to the TR- 2100’s Local RS-232 port (found on the front panel). 3. Turn on the computer and start Win95. 4. Open Comms Manager from the System menu, and note the port and port baud rate settings. 5. Exit the DS program now (close the program). Do not just ...

16 Duplicates the function of the front panel LED. Printer If a printer is connected to the TR-2100, it will report three separate events: • All entries to the event log • The system status will be printed with a test record when the Test button is pressed. • A full data record with channel configuration, profile and graphical display of analogue and digital waveforms is printed when the recorder is triggered. To enable the printer, see Chapter 4. To select the printer type, see the Display Station manual. Printout Format The TR-2100 logo is printed at the top, and th ...

46 Hardware Settings Acquisition Board Configuration Switches Set-up the acquisition board configuration switches as shown below. Reference the System Drawings for number of channels and options to be enabled. Bank 1 Table 7 Table 8 * Default setting Switch Function Off On 1 Digital-only cards Yes No 2 System frequency 50 Hz 60 Hz 3 No. of analogue cards – 1 4 No. of analogue cards – 2 See 8 5 Cross triggering Disable Enable 6 GPS receiver Yes No 7 Time code port Master Slave 8 (undefined) Switch 3 Switch 4 Analogue Input Boards Off Off 1 Off On 2 On Off 3 On On 4 Bank ...