CraftBot Flow Installation Manual
Text of the manual
DOOR INSTALLATION MANUAL V1.0
WWW.CRAFTBOT.COM
WWW.CRAFTBOT.COM
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Table of contents
DOOR INSTALLATION MANUAL V1.0
WWW.CRAFTBOT.COM
1. Introduction
For best print quality, some filaments may need to stabilize the build area temperature. This can significantly reduce
the possibility of warping printed objects.
That’s why we also offer the elegant and durable printer cover and door for Craftbot printers.
Learning from previous feedback, the dome now consists of two parts so that we can easily reach the machine if
necessary. The door was fitted with an electric lock so that we could even open it remotely.
This manual walks you through the steps of installing the door.
DOOR INSTALLATION MANUAL V1.0
WWW.CRAFTBOT.COM
2. Accessories
Below you can see contents of the box. First of all, check the list to make sure nothing is missing!
1. Left door (1x)
2. Right door (1x)
3. Door lock (1x)
4. Door cable (1x)
5. Cable holder (10x)
6.
Tools needed:
•
1.5mm allen key
•
2.0mm allen key
Installation time: 10 mins
3. Installation
Please follow the steps listed below to assemble the dome.
•
Connect the cable other end to the door lock assembly.
•
Connect the door cable to the connector located in the upper right corner in the printer.
DOOR INSTALLATION MANUAL V1.0
WWW.CRAFTBOT.COM
•
Secure the wire with the supplied cable holders. (10x) Recommended spacing is 10cm apart.
•
Attach the doors, one-by-one. Use the 1.5mm allen key as a spacer under the door.
•
Press the door againist the case and tighten the upper screw in the upper hinge. (2.00mm allen key)
DOOR INSTALLATION MANUAL V1.0
WWW.CRAFTBOT.COM
•
Check the gaps between the case and the doors. It should be even all around the door.
•
Press the door againist the case and tighten the rest of the screws. (3x)
•
Arrange the door to the middle of the cutout. The gaps have to be equal on the sides.
DOOR INSTALLATION MANUAL V1.0
WWW.CRAFTBOT.COM
•
Press the door lock againist the case and tighten the door lock securing screws, with the 1.5mm allen key. (2x)
•
Enable the door in the Settings / Door menu.
•
Adjust the other parameters if necessary.
•
Open the door with the button on the main screen.
CraftBot is made in the EU.
©Copyright 2008-2020 by CraftUnique Ltd. All Rights Reserved.
CONTACT:
CraftUnique Ltd.
Salgótarjáni str. 12-14.
Budapest 1087, Hungary
Phone: +36 1 700 8060
Web: www.craftbot.com • www.craftbotusa.com
Cooperation between 3D printer and people has never been easier.
Get in touch!
CraftBot is made in the EU.
Copyright 2013-2020 by CraftUnique Ltd. All Rights Reserved.
CONTACT:
CraftUnique Ltd.
Salgótarjáni str. 12-14.
Budapest 1087, Hungary
Phone: +36 1 700 8060
Web: www.craftbot.com • www.craftbotusa.com
Cooperation between 3D printer and people has never been easier.
Get in touch!
