CORNING LSE 6703 Instruction Manual

6704 Corning LSE Platform Rocker, 230V 6705 Corning LSE Platform Rocker, double platform, 115V 6706 Corning LSE Platform Rocker, double platform, 230V

1. General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Installation of the Platform Rocker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.2 Selecting the Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.3 Attaching the Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.4 Installing Double Stacking Platform. . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5. Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6. Maintenance and Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7. Product Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 8. Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

1.0 General Specifications Speed Settings 5 to 120 tilts/minute Timer 0 to 2 hours or continuous Motion Rocking Tilt Angle Fixed 7° Maximum Load 11 lbs./5 kg Ambient operation Range +4°C to 70°C Dimensions 12.8 x 14.2 x 5.7 in. (32.5 x 36 x 14.5 cm) Weight 11.7 lbs./ 5.3 kg Electrical 115V, 50/60Hz 230V, 50/60Hz Warranty 5 years Platform Size 11.8 x 11.8 in. (30 x 30 cm) 2.0 Safety Precautions Do not use the rocker near water sources. Be sure that water does not get on the device, especially during the cleaning procedures. ZZ Do not expose the rocker to aggressive vapors (e.g., organic solvents). ZZ Do not insert any objects into the rocker (such as screwdriver or metal rods). ZZ Never operate the rocker without the platform securely attached. ZZ Hazardous samples should be shaken only in appropriate containment vessels. 1. Switch on POWER 2. Set SPEED potentiometer on desired value 3. Set TIME potentiometer on desired value or on HOLD – continuous function (yellow light next to HOLD will illuminate) 4. Press START/STOP button to start rocking 5. Press START/STOP button to stop rocking (HOLD position). Device automatically stops after the set time passes. Note: Pressing the START/STOP button during operation will reset the timer. Do not rock flammable or explosive samples!

3.1 Unpacking Before starting the installation, carefully examine the rocker for possible damage or missing parts. ZZ Open the box and carefully remove the padding. Check that the rocker has not been visibly damaged during transportation. Keep the packing material until you ensure that the rocker works properly. ZZ Carefully lift the device out of the box. ZZ Be sure that the following information is included on the serial label located on the back of the unit: • Serial Number • Product Number • Electrical Rating ZZ Ensure that the power cord has a pin configuration that fits into a wall socket according to the local standard. Should any kind of damage have occurred during transportation, contact the carrier immediately. The carrier is responsible for shipping damage. 3.2 Selecting the Location ZZ Put the rocker on a horizontal, leveled, and stable surface ZZ Leave enough space around the rocker for normal air circulation (10 cm minimum) ZZ Leave enough space around the rocker for easy access and maintenance ZZ Avoid locations subject to shocks and vibrations ZZ Avoid locations subject to frequent power fluctuations or power losses, as this may affect rocker performance Select a location that is dry and not subject to drafts or moving air from heating or air conditioning vents or air blown by other equipment. Place the unit on a flat, preferably non-flammable, surface. Allow sufficient room around the unit for access and cooling (six inches minimum on all sides is suggested). Plug the unit into a properly grounded outlet. Using the lifter, insert the block(s) into the well. The unit is now ready for use.

3.3 Attaching the Power Cord Connect the main power cord to the rocker and then connect the plug end of the cord to a grounded wall socket. Avoid lines to which powerful electric motors, refrigerators, and similar devices are connected. Be careful when you plug the cord to a grounded wall socket! Do not touch plug with wet hands! Do not pull the plug by the cord! 3.4 Installing Double Stacking Platform 1. Set posts (A) through the four holes at the corners of the bottom platform. 2. Add washer (B) and nut (C) to each post. 3. Fit upper platform (D) on the top of the four posts through the corner holes. 4. Screw on the four metal knurl nuts (E) to secure the upper platform. NOTE: Misuse or unauthorized modifications will waive the warranty rights. If the equipment is used in a manner not specified by the manufacturer, the safety features of the rocker may be impaired.

SPEED potentiometer – Sets the rocker speed TIME potentiometer – Sets the time of the rocker HOLD yellow light – Illuminates when rocker is set for continuous running START/STOP button – START or STOP rocking RUN green light – Illuminates when the rocker is running 1 2 3 4 5 6

5.0 Troubleshooting Guide Be sure to disconnect the rocker from the main power source immediately in case of any signs of malfunction and contact Corning Customer service at 800.492.1110 or 978.442.2200. Problem Solution POWER switch does not light up Check the power connection. Check fuses Contact Corning Customer Service. Rocker does not START Check the power connection. Check fuses. Contact Corning Customer Service. 6.0 Maintenance and Cleaning ZZ No routine maintenance or lubrication is required. ZZ It is recommended that the rocker be kept clean to ensure a long, trouble-free operation. The outside housing of the platform rocker may be cleaned with a soft, damp cloth when needed. Do not use any aggressive or abrasive cleaners (acetone, nitro, polish, etc.), as they may permanently damage the rocker finish. Before cleaning the rocker, always unplug the power cord from the wall socket! Make sure the rocker is switched off before installing an additional platform!

According to Directive 2012/19/EU of the European Parliament and Council of 4th July 2012 on waste and electronic equipment (WEEE) as amended, the Corning® LSE Platform Rockers is marked with the crossed- out wheeled bin and must not be disposed of with domestic waste. Consequently, the buyer shall follow the instructions for reuse and recycling of waste electronic and electrical equipment (WEEE) provided with the products and available at www.corning.com/weee.

8.0 Limited Warranty Corning Incorporated (Corning) warrants that this product will be free from defects in material and workmanship for a period of five (5) years from date of purchase. CORNING DISCLAIMS ALL OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof that proves defective in material or workmanship within the warranty period, provided the purchaser notifies Corning of any such defect. Corning is not liable for any incidental or consequential damages, commercial loss, or any other damages from the use of this product. This warranty is valid only if the product is used for its intended purpose and within the guidelines specified in the supplied instruction manual. This warranty does not cover damage caused by accident, neglect, misuse, improper service, natural forces, or other causes not arising from defects in original material or workmanship. This warranty does not cover motor brushes, fuses, light bulbs, batteries, or damage to paint or finish. Claims for transit damage should be filed with the transportation carrier. In the event this product fails within the specified period of time because of a defect in material or workmanship, contact Corning Customer Service at: USA/Canada 1.800.492.1110, outside the U.S. +1.978.442.2200, visit www.corning.com/lifesciences, or contact your local support office. Corning Customer Service will help arrange local service where available or coordinate a return authorization number and shipping instructions. Products received without proper authorization will be returned. All items returned for service should be sent postage prepaid in the original packaging or other suitable carton, padded to avoid damage. Corning will not be responsible for damage incurred by improper packaging. Corning may elect for onsite service for larger equipment. Some states do not allow limitation on the length of implied warranties or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights. You may have other rights which vary from state to state. No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend the period of this warranty. For your reference, make a note of the model number, serial number, date of purchase, and supplier here. Model No._ ___________________________ Serial No.____________________________________________ Date Purchased ________________________ Supplier_____________________________________________

www.corning.com/lifesciences/warranty. © 2018 Corning Incorporated. All rights reserved. 5/18 CLS-AN-491 REV1/11319-30514 For more specific information on claims, visit the Certificates page at www.corning.com/lifesciences. Warranty/Disclaimer: Unless otherwise specified, all products are for research use only. Not intended for use in diagnostic or therapeutic procedures. Not for use in humans. Corning Life Sciences makes no claims regarding the performance of these products for clinical or diagnostic applications. For a listing of trademarks, visit www.corning.com/clstrademarks. All other trademarks are the property of their respective owners. Corning Incorporated Life Sciences 836 North St. Building 300, Suite 3401 Tewksbury, MA 01876 t 800.492.1110 t 978.442.2200 f 978.442.2476 www.corning.com/lifesciences A S IA / P A C IF IC Australia/New Zealand t 61 427286832 China t 86 21 3338 4338 f 86 21 3338 4300 India t 91 124 4604000 f 91 124 4604099 Japan t 81 3-3586 1996 f 81 3-3586 1291 Korea t 82 2-796-9500 f 82 2-796-9300 Singapore t 65 6572-9740 f 65 6861-2913 Taiwan t 886 2-2716-0338 f 886 2-2516-7500 EUR OP E [email protected] France t 0800 916 882 f 0800 918 636 Germany t 0800 101 1153 f 0800 101 2427 The Netherlands t 020 655 79 28 f 020 659 76 73 United Kingdom t 0800 376 8660 f 0800 279 1117 All Other European Countries t +31 (0) 206 59 60 51 f +31 (0) 206 59 76 73 LA T IN A M ER IC A [email protected] Brasil t 55 (11) 3089-7400 Mexico t (52-81) 8158-8400 For additional product or technical information, visit www.corning.com/lifesciences or call 800.492.1110. Outside the United States, call +1.978.442.2200 or contact your local Corning sales office.