DynaLock 3101B Installation Instructions Manual

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com The 3101B Delay Egress System is a 1500 pound holding force electromagnetic lock electronically controlled to provide a 15 or 30 second delay in unlocking. The 3101B requires both mechanical and electrical installation procedures as described herein. When completed, a simple adjustment procedure to set door movement will finalize the installation. INSTALLATION DESCRIPTION ELECTRICAL INSTALLATION After mechanical installation is complete the 3101B needs to be wired and adjusted. A continuous power source, 12 or 24 VDC or VAC is required. Once low voltage power is supplied the unit is fully operational. Delay egress systems also normally require fire panel tie-in. All other wiring is for selected options. NOTE: Please see Egress Sensor Adjustment (page 8) before applying power. Familiarize yourself with the door and frame conditions. The lock must mount rigidly to the underside of the door frame header and against the vertical strike jamb. The door mounted armature is supplied with hardware that allows it to pivot slightly and pull away from the door as part of the delayed egress function. NOTE: This lock does not change hands to match the hand of the door. Do not remove the coil assembly from the lock housing. NOTE: For locks ordered with the DSM option, please verify that two magnets are installed inside the armature housing. MECHANICAL INSTALLATION The electromagnetic lock and armature are ruggedly constructed and designed to provide years of trouble-free service. Care must be taken during installation and use that the lock face and armature face are kept free of dirt, rust, paint, or any other obstruction which may interfere with the lock and armature making good contact. HANDLING

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com MODEL #3101B BILL OF MATERIALS (1) 3101B LOCK ASSEMBLY (1) ARMATURE (1) ARMATURE HOUSING (1) ARMATURE MOUNTING PLATE ASSEMBLY (1) HARDWARE KIT (1) DOOR SIGN - “15 SECONDS” * (1) TEMPLATE (1) INSTALLATION MANUAL (1) Electric Drill (1) #2 Phillips Screwdriver (1) Soft Faced Mallet (1) Hammer (1) Center Punch (1) Pencil & Tape Drill Bits: 1/8”, 5/16”, 3/8”, 9/16” REQUIRED TOOLS (5) Fas-Trak Mounting Screws #10 x 1” phillips pan head tek screw (5) Fas-Trak Mounting Screws 10-24 x 1/2” phillips pan head machine screw (1) Armature Mounting Screw 5/16-18 x 1” hex flat head machine screw, turned (1) Armature Spacer 3/8”D x 0.360”L (1) Armature Spring Compression spring (4) Armature Mounting Plate Screws #10 x 1” phillips flat head sheet metal screw (4) Armature Housing Mounting Screws 8-32 x 3/8” phillips machine screw (1) Anti-Tamper Cover Screwdriver #6 spanner key (1) Fas-Trak Set Screw Wrench 1/8” ball head hex wrench (1) Armature Bolt Wrench 3/16” hex wrench (1) Thread Locking Compound Liquid (2) Bypass/Reset Key (1) Mini Screwdriver NOTE: For further parts clarification refer to the Exploded Parts View on page 14 or consult factory. HARDWARE KIT CONTENTS (PN 301325) QTY. ITEM DESCRIPTION General Information........................................... 1 Bill Of Materials................................................. 2 Using The Template........................................... 3 Mounting The Armature Assembly...................... 4 Mounting The Lock............................................. 5 Basic Set-Up...................................................... 6 Basic Wiring...................................................... 7 Egress Sensor Adjustment................................. 8 Indicator Descriptions......................................... 9 Optional Set-Up................................................. 10 Option Wiring..................................................... 11-12 Factory Wiring................................................... 13 Exploded Parts View.......................................... 14-15 TABLE OF CONTENTS * “30 SECONDS” SIGN AVAILABLE

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com Inspect the door frame and determine if an angle bracket, spacer or filler plate will be required for installation. The lock will require a 2-9/16” wide header stop for a suitable mounting surface. *These items are available from DynaLock. MOUNTING CONSIDERATIONS NORMAL MOUNTING *FILLER PLATE REQUIRED *ANGLE BRACKET REQUIRED USING THE TEMPLATE Fold the template on the dotted line to form a 90 degree angle. Scoring the template with a straight edge and a screwdriver will make it fold easier. With the door in the closed and latched position place the template against the header and door with one edge against the vertical strike jamb and tape in place. Transfer all hole locations to both the door and header with a center punch, then remove the template from the door. Referring to the template drill two 1/8” dia. lock mounting holes and one 9/16” dia. wiring hole in the top of the frame, at the transferred locations. 1. 2. 3. 4. Drill the remaining transferred holes in the face of the door to accept the Armature Mounting Plate Assembly: a. Four 1/8” dia. mounting screw holes, 1” deep. b. One 3/8” dia. armature screw clearance hole, 3/8” deep. c. One 5/16” dia. adjustment wheel screw clearance hole, 1/4” deep. 5. 2-9/16” 2-9/16” *SPACER PLATE REQUIRED 9/16" DIA. WIRING HOLE 1/8" DIA. DRILL PLACE AGAINST HEADER FOLD ON DOTTED LINE 1/4" DIA. ARMATURE GUIDE PIN HOLES 9/16" DEEP (2 REQ'D.) 1/8" DIA. DRILL (4 PLACES) PLACE AGAINST JAMB OPPOSITE HINGES FOR L.H.R. DOOR INSTALLATION PLACE AGAINST JAMB OPPOSITE HINGES FOR R.H.R. DOOR INSTALLATION #3101-B SERIES ELECTROMAGNETIC LOCK 11/32" DIA. ARMATURE SCREW CLEARANCE HOLE 1" DEEP CARDBOARD TEMPLATE HINGE SIDE OF DOOR

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com Using the four #10 x 1” flat head sheet metal screws attach the armature mounting plate to the door. Firmly tighten the screws with a #2 phillips screw driver. MOUNTING THE ARMATURE ASSEMBLY Attach the Armature to the Mounting Plate Assembly using the hardware supplied. Apply the supplied thread locking compound to the threads of the Armature Mounting Screw and firmly tighten with a 3/16” hex wrench. The head of the armature mounting screw must not project beyond the face of the armature. Failure to properly secure the Armature to the door could result in serious injury or possible security breach. Check the installation by pushing in on a corner of the Armature - it should move. Although the mounting screw is tight the Armature should have approximately 1/4” of free play, under slight spring tension. (4) 1/8” DIA. MOUNTING SCREW HOLE - 1” DEEP (1) 3/8” DIA. ARMATURE SCREW CLEARANCE HOLE, 3/8” DEEP (4) #10 X 1” MOUNTING SCREW (1) 5/16” DIA. ADJUSTMENT WHEEL SCREW CLEARANCE HOLE - 1/4” DEEP 0.360”L ARMATURE SPACER 5/16-18x1” TURNED ARMATURE MOUNTING SCREW ARMATURE HOUSING ARMATURE 8-32x3/8” ARMATURE HOUSING SCREW SPRING ARMATURE MOUNTING PLATE ASSEMBLY

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com MOUNTING THE LOCK Before installation begins remove the rear Electronics Cover, End Cover and Sensor Cover Assembly (see page 14 for parts locations). Carefully unplug the sensor harness from the circuit board connector labeled J5 then detach the Sensor Cover Assembly from the lock. In the upper inside corners of the lock housing are located two #1/4-28 set screws. Using the 1/8” ball head hex wrench loosen (do not remove) the two set screws until the Fas-Trak Baseplate is free (Fig. “C”). Remove the Fas- Trak. Place the Fas-Trak against the header with the slot counter bores visible and the tabs facing the door (Fig. “A”). Attach the Fas-Trak to the header at both slotted hole locations, with two #10 x 1” tek screws or 10-24x1/2” machine screws. Tighten the screws just snug enough to allow for final adjustment. Temporarily mount the lock to the Fas-Trak by offsetting the lock 1-1/8” from the jamb (Fig. “C”) and tipping the front of the lock down engaging the rear flange of the Fas-Trak (Fig. “B”). Rotate the lock up allowing one tab to pass through the corresponding notch in the top of the lock housing. Slide the lock into position. Close and latch the door. Check that the armature and lock faces make full contact. If any adjustment is required gently tap the housing with a soft mallet until full contact is achieved. Open the door, remove the lock from the Fas-Trak and tighten both slot screws. Drive three more screws into the header using the Fas-Trak as a physical template. Screw heads must not project above the Fas-Trak. Any roughed-in wiring may be brought in at this time through the slotted wiring holes. Re-install the lock on the Fas-Trak. Firmly tighten both housing set screws with the 1/8” ball head hex wrench. Re-install the End Cover and Sensor Cover Assembly. Carefully plug the Sensor harness back into the J5 connector on the circuit board (see page 13 for connector information). If the lock wiring and set-up are not being done at this time replace the Electronics Cover and see that these instructions are left for the electrical installer. 1. 2. 3. 4. FAS-TRAK TABS SET SCREW LOCK VERTICAL JAMB FIG. “C” 1-1/8” OFFSET TABS FACING DOOR VISIBLE SLOT COUNTER BORES LOCK ENGAGE REAR FLANGE FAS-TRAK FIG. “B” FIG. “A” SET SCREW

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com BASIC SET-UP - Voltage Selection Check that the voltage selection jumper (J4) is properly set to match your input power. Note that all locks are factory set for 24 volts. - Fire Alarm Control Check that the fire alarm control jumper (J9) is properly set to match your fire panel input contacts. If fire panel tie-in is not required leave jumper at factory setting (N.O.). Remove the Electronics Cover to expose the circuit board assembly. (Factory Setting) (Factory Setting) 1. 2. 3. - System Selector Switches The selector switches (DS1) that control major system functions are factory set to the OFF position for basic lock operation. Switch 1 will be used during sensor adjustment (page 8). Switches 2, 3 and 4 are only used for options described on page 10. 4. V C FA (Factory Setting) V FA C SET FOR 24 VOLTS REMOVEABLE JUMPERS SET FOR 12 VOLTS NO C NC SET FOR NORMALLY OPEN INPUT NO C NC SET FOR NORMALLY CLOSED INPUT 1 2 3 4 ON DS1 STANDARD SOFTWARE VERSION 2K1.1

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com BASIC WIRING Terminals 1& 2 - Power Input. May be 12 or 24 Volts, AC or DC, uninterrupted. Current requirement is 0.75 Amps for 12 Volts and 0.5 Amps for 24 Volts (check voltage selection jumpers “V” - page 6). DO NOT INTERRUPT INPUT POWER (TERMINALS 1 & 2) FOR AUTHORIZED ACCESS/EGRESS. EXTERNAL ACCESS/EGRESS CONTROLS (EX. KEYPAD, CARD READER, ETC.) SHOULD USE DEDICATED BYPASS TERMINALS 7 & 8 or 9 & 10 (SEE PAGE 11). Terminals 3 & 4 - Fire Panel Input. May be normally-open (N.O.) or normally-closed (N.C.) dry contacts from fire panel (check fire alarm control jumper “FA” - page 6). When the fire panel trips, the 3101B will release, the audible will sound a constant tone and the bi-color LED (LED1) will change to green. When the fire panel is reset, the 3101B will reset and lock. NOTE: DO NOT APPLY POWER TO TERMINALS 3 & 4 OR DAMAGE WILL OCCUR. Basic hook-up is shown below. For other system features hook-up see “Option Wiring” (page 11). PROPER OPERATION OF THE 3101B REQUIRES ADJUSTMENT OF THE EGRESS SENSOR PROCEED TO EGRESS SENSOR ADJUSTMENT POWER FAC CONTINUOUS 1 2 3 4 POWER INPUT 12/24 VAC/VDC FIRE PANEL INPUT N.O. OR N.C. CONTACTS

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com EGRESS SENSOR ADJUSTMENT WHEEL STOP INSTALLED (LOCKS ADJUSTMENT) SEE PAGE 10 FOR LOCATION OF ELECTRONIC PARTS MENTIONED IN THIS SECTION The sensor and armature assembly are designed for use on a door with existing mechanical latching hardware. If used on a door without a latch, false alarms are possible. In these cases, we suggest using an external trigger such as our 6451 Exit Sensor Bar - connect using terminals 11&12 and disable this internal sensor (see pages 10&11). With the door closed and latched apply input power to terminals 1 & 2. Slide selector switch (DS1) #1 to the ON position to activate the Set-Up mode. Rotate the on-board keyswitch counter-clockwise. The 3101B should now be unlocked (LED1-OFF). Open the door. Temporarily remove the Adjustment Wheel Stop from the Armature Mounting Plate and close the door. Set aside for re-installation later. With the door closed observe the bi-color LED (LED1) on the circuit board. It should be lit red. If it is not lit, rotate the adjustment wheel counter-clockwise as necessary to ensure that it will contact and fully depress the ball plunger on the lock. Rattle the door to ensure the LED remains lit. With the door closed and LED1 lit red, unlatch and slowly open the door. The LED will shut off as soon as the door opens far enough for the ball plunger to fully project. With adjustment completed, re-install the adjustment wheel stop to lock-in the adjustment. Close the door, slide selector switch (DS1) #1 back to the OFF position and return the on-board keyswitch to the center position to re- lock the 3101-B. Unlatch and push on the door until delay egress triggers (1-3 seconds). The audible will sound and LED1 will flash red. After 15 seconds the lock will release. Turn the on-board keyswitch clockwise to reset the lock. If delayed egress triggers too soon, or fails to trigger, re-adjust the sensor adjustment wheel for desired sensitivity. WHEEL STOP MOUNTING SCREW WHEEL STOP EGRESS SENSOR ADJUSTMENT WHEEL ARMATURE MOUNTING PLATE 1. 2. 3. 4. 5. 6. DOOR CLOSED AND LATCHED DOOR UNLATCHED & MOVED

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com INDICATOR & AUDIBLE DESCRIPTIONS LED2 - WATCHDOG LED INDICATOR (Located upper right corner of circuit board.) Troubleshooting indicator - monitors proper operation of the microprocessor. LED1 - BI-COLOR LED INDICATOR (Located at center of circuit board.) Indicates lock status and monitors door movement during egress sensor adjustment. BUILT-IN KEYSWITCH OPERATION CENTER CLOCKWISE (SPRING LOADED) COUNTER-CLOCKWISE NORMAL / LOCKED RESET AFTER DELAY EGRESS ALARM BYPASS / UNLOCKED WITHOUT ALARM POSITION DESCRIPTION CONDITION AUDIBLE SIGNAL LOCK LED 1 LED 2 DELAY EGRESS ALARM One second pulse rate during delay cycle. ON BLINK RED RED DELAY EGRESS ALARM Steady tone after delay until reset. OFF GREEN RED FIRE ALARM RELEASE Steady tone until fire alarm contacts are reset. OFF GREEN RED OPTIONAL REMOTE AUTHORIZED BYPASS (TERMINALS 7&8 / 9&10) None, unless bypass audible is enabled (dip switch 2). If door is held open past relock time, goes into delay egress alarm & requires reset. OFF GREEN RED FACTORY SERVICE REQUIRED Steady tone. N/A N/A BLINK RED OR OFF POOR MAGNETIC BOND Rapid pulse rate until problem is corrected (only functional with Dynastat Force Sensor option). N/A FAST BLINK RED RED

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com OPTIONAL SET-UP - Audible Selector The on-board audible is normally enabled for local signaling of lock and alarm status. To completely disable the audible remove jumper (J11). (Factory Setting) 2. - System Selector Switches Set the System Selector Switches (DS1) to address your specific system requirements. The normal factory setting is all switches off. 1. - Sensor Control The egress sensor may be disabled if you wish to trigger the lock via external remote contacts on input terminals 11 & 12. Position jumper (J10) to disable the egress sensor as shown. 3. (Factory Setting) C S A C A S 1 SYSTEM SET-UP NORMAL SET-UP MODE 2 BYPASS AUDIBLE DISABLED ENABLED 3 NUISANCE DELAY 1 SEC. 3 SEC. 4 EGRESS DELAY 15 SEC. 30 SEC. SWITCH FUNCTION OFF ON MODE SETTINGS DS1 AUDIBLE ENABLED AUDIBLE DISABLED REMOVE OFF C ON SENSOR ENABLED OFF C ON SENSOR DISABLED 1 2 3 4 ON * *Only applies to terminals 9&10 (see next page)

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com OPTION WIRING REMOTE BYPASS INPUT Momentarily closing a normally-open dry contact across terminals 7 & 8 will immediately release the lock without alarm. The door will remain unlocked until the contact is opened. Connect authorized access/egress control(s) here (typical). REMOTE RESET INPUT Momentarily closing a normally-open dry contact across terminals 5 & 6 will reset and re-lock the 3101B following delayed egress and re-closure of door. REMOTE TRIP INPUT Momentarily closing a normally-open dry contact across terminals 11 & 12 will initiate delayed egress. This input may be used as a redundant or substitute means of triggering delayed egress if built-in sensor initiation is not desired (see page 10, note 3). INPUT DESCRIPTIONS ! WARNING: DO NOT APPLY POWER TO INPUTS MARKED “ ! ” OR DAMAGE WILL OCCUR A C B D REMOTE BYPASS INPUT TIME DELAY Momentarily closing a normally-open dry contact across terminals 9 & 10 will immediately release the lock without alarm. The door will remain unlocked for a period of time controlled by on-board adjustable timer S2. To increase the delay rotate timer S2 clockwise. Range is 1 to 75 seconds (~5 sec. per click). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 NC NO C NC NO C NC NO C NC NO C REMOTE RESET INPUT REMOTE BYPASS INPUT REMOTE TRIP INPUT DELAY EGRESS OUTPUT DYNST OPTION OUTPUT DSM OPTION OUTPUT ATS OPTION OUTPUT STANDARD INPUT/OUTPUT TERMINALS (TYPICAL - ALL MODELS) OPTIONAL OUTPUT TERMINALS (AS ORDERED) A B D E F G H 3101B CIRCUIT BOARD C SEE PAGE 7 FOR WIRING INFORMATION S2 REMOTE BYPASS INPUT TIME DELAY

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com OPTION WIRING MONITORING OUTPUT DESCRIPTIONS DELAY EGRESS OUTPUT Delay egress alarm monitoring. SPDT dry relay contacts rated 1Amp @ 24 Volts Contacts change state upon initiation of delayed egress, after the nuisance delay has elapsed. They remain in that state until door is closed and reset. DYNST OPTION OUTPUT Dynastat bond sensor monitoring. SPDT dry relay contacts rated 1Amp @ 24 Volts Contacts change state to signal lock status as either secure or unsecure. Armature misalignment can also create an unsecure condition. DSM OPTION OUTPUT Door position sensor monitoring. SPDT dry relay contacts rated 0.5Amp @ 24 Volts Contacts change state to signal physical door position as either closed or open. DSM is an independent circuit that does not require lock power to operate. ATS OPTION OUTPUT Anti-Tamper Switch monitoring. SPDT dry relay contacts rated 0.5Amp @ 24 Volts Contacts change state to signal removal of the lock electronics cover. TYPICAL WIRING NOTE: INDICATORS ARE NOT INCLUDED NOTE: INDICATORS ARE NOT INCLUDED NOTE: INDICATORS ARE NOT INCLUDED NOTE: INDICATORS ARE NOT INCLUDED 13 14 15 ALARM SECURE NC C NO TO INDICATOR POWER SUPPLY 16 17 18 UNSECURE SECURE NC C NO TO INDICATOR POWER SUPPLY 19 20 21 OPEN CLOSED NC C NO TO INDICATOR POWER SUPPLY 22 23 24 TAMPER NORMAL NC C NO TO INDICATOR POWER SUPPLY E F G H

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com FACTORY WIRING DYNASTAT FORCE SENSOR OPTION HARNESS (2 COND.) DSM DOOR STATUS SWITCH OPTION HARNESS (3 COND.) SENSOR COVER ASSEMBLY SENSOR HARNESS (4 COND.) COIL HARNESS (4 COND.) KEYSWITCH HARNESS (3 COND.) ON-BOARD KEYSWITCH DSM OPTION SENSOR LOCK COIL ASSEMBLY 3101B CIRCUIT BOARD Harness connectors J3 and J6 are not polarity sensitive. J3 & J4 are interchangeable - jumpers can go on J3 and coil can go on J4. Harnesses J6 and J8 are only present if the 3101B is equipped with the DYN - Dynastat Force Sensor and/or DSM - Door Status Switch Options. Observe polarity when re-connecting the J5, J7 and J8 harness connectors. Orient these connectors with respect to harness wire colors as follows: J5 WHT GRN RED BLK J7 WHT BLK BLU J8 GRN WHT RED 1. 2. 3. 4. NOTES: BPM BYPASS MONITOR OPTION (2 YELLOW COND.) MAINTAINED - N.O., 4A@125V

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com EXPLODED PARTS VIEW LEGEND ON NEXT PAGE 1 2 3 4 5 6 11 12 13 1-1/2” 1/4” 1-1/2” 1/2” 7 8 9 10 14 15 17 16 18 19 20 21

INSTALLATION INSTRUCTIONS 705 Emmett Street Bristol, CT 06010 1-877-DynaLock www.dynalock.com EXPLODED PARTS VIEW LEGEND ITEM DESCRIPTION PART # 1 Fas-Trak Baseplate 300011 2 #10x1” Self-Tapping Screw * 2 10-24x1/2” Machine Screw * 3 Lock Housing 4 Access Cover & Sensor Assembly 301037 5 8-32x3/8” Machine Screw 300608 6 1/4-28x1/4” Set Screw 300604 7 Electronics Cover 300353 8 6-32x1/2” Spanner Security Screw 700058 9 End Cover 300010 * Part of Hardware Kit (301325) Refer to Page 14 for parts locations. ITEM DESCRIPTION PART # 10 Armature Mounting Plate Assy. 301038 11 Sensor Adjustment Wheel & Stud 301383 12 Wheel Stop 301003 13 8-32x1/2” Wheel Stop Screw 301005 14 #10x1” FHS Mtg. Plate Screw * 15 Armature Housing w/ pads 301334 16 8-32x3/8” Armature Mtg. Screw * 17 Disc Magnet (DSM only) 301289 18 Armature 300373 19 Compression Spring * 20 0.360”L Armature Spacer * 21 5/16-18x1” Armature Bolt (turned) *

AND THE KEYS TO THE END USER UPON COMPLETION OF THE 3101B INSTALLATION FOR PRODUCT SUPPORT AND PARTS ORDERING INFORMATION CONTACT: DynaLock Corp. 705 Emmett Street Bristol, CT 06010 Bus: (877) 396-2562 Toll-Free USA (860) 582-4761 Fax: (860) 585-0338 DYNALOCK ON THE INTERNET: E-mail: [email protected] Website: www.dynalock.com GWXT Auxiliary Lock FWAX Special Locking Arrangements CSFM California State Fire Marshal