DORIC DS2500 Installation Manual

Wetherill Park NSW 2164 Australia Ph: 1300 132 389 Fax: 1300 652 292 [email protected] www.doric.com.au DS2500 I FLUSH MOUNT MORTICE SLIDING DOOR LOCK

Wetherill Park NSW 2164 Australia Ph: 1300 132 389 Fax: 1300 652 292 [email protected] www.doric.com.au DS2500 I FLUSH MOUNT MORTICE SLIDING DOOR LOCK INSTALLATION GUIDE 1 170.00 19.00 3.50 6.00 9.00 Extrusion width 25mm to 55mm Extrusion width 25mm to 55mm R3.00 3.50 Centred in Extrusion Centred in Extrusion 154.80 OFFSET TO CENTRE OF SIDE CUTOUT FROM CENTRE OF FRONT CUTOUT OFFSET TO CENTRE OF SIDE CUTOUT FROM CENTRE OF FRONT CUTOUT OFFSET TO CENTRE OF KEEPER CUTOUT FROM CENTRE OF FRONT CUTOUT 247.00 30.00 R5.00 Backset Length: Surface Mount: 30mm Tab Mount: 28.9mm + Extrusion thickness 205.50 25.00 12.80 12.80 4.50 w/ 8.50 CS 4.50 w/ 8.50 CS 153.30 126.00 20.00 R3.00 12.00 12.00 2.50 2.50 Centered in Jamb 176.50 Furniture cut outs Front and back of extrusion Lockbody cut outs (opt 1) Side of extrusion - Surface Mounted - Lockbody cut outs (opt 2) Side of extrusion - Tab Mounted (i.e. flush) - Optional: Jamb cutouts for DN1291 Mortice Keeper (if being used) Extrusion Cut Out Details A B A + B

Wetherill Park NSW 2164 Australia Ph: 1300 132 389 Fax: 1300 652 292 [email protected] www.doric.com.au DS2500 I FLUSH MOUNT MORTICE SLIDING DOOR LOCK INSTALLATION GUIDE 2 Fork M3 fixing screw Rotate 180° STEP 1: SET LOCKBODY The Fork at the rear of the lockbody should be oriented so that it is closest to the internal side of the door (i.e. toward the snibbed furniture side). If the fork is in the incorrect orientation for your door application: Remove the M3 fixing screw, Rotate the fork 180 degrees, and re-tighten fixing screw. Depending on your selected configuration you will need to place the furniture in either the locked or unlocked position. Double/Single Cylinder Configuration Cylinder on Internal & External or, Cylinder on Internal Furniture needs to be placed in the locked position as indicated by the arrows aligning. No Cylinder Configuration Latching only, no cylinders Furniture needs to be placed in the unlocked position as indicated by the arrows being misaligned. STEP 2: SET FURNITURE LOCK CONFIGURATION INTERNAL SIDE EXTERNAL SIDE INTERNAL SIDE EXTERNAL SIDE

Wetherill Park NSW 2164 Australia Ph: 1300 132 389 Fax: 1300 652 292 [email protected] www.doric.com.au DS2500 I FLUSH MOUNT MORTICE SLIDING DOOR LOCK INSTALLATION GUIDE 3 Screw QTY Extrusion Width M4X26MM 2 25-36mm M4X35MM 2 36-45mm M4X43MM 2 45-51mm M4X50MM 2 51-55mm Fit internal and external furniture onto the extrusion ensuring that the cutout in the gear aligns with the boss of the lockbody. 4a. Fix with the supplied M4 fixing screws (supplied based on extrusion width). Refer to table below as a reference for the correct length of fixing screw. 4b. Operate both internal and external cylinder to ensure correct operation. Operate sliding snib to ensure correct operation. Screws supplied based on specified extrusion width STEP 3: FITTING FURNITURE STEP 4: FIXING Ensure the gear cutouts align INTERNAL SIDE EXTERNAL SIDE

Wetherill Park NSW 2164 Australia Ph: 1300 132 389 Fax: 1300 652 292 [email protected] www.doric.com.au DS2500 I FLUSH MOUNT MORTICE SLIDING DOOR LOCK INSTALLATION GUIDE 4 5a. Ensure the furniture and the lockbody are in the unlocked position: The sliding snib is in the bottom position (A) The lockbody tongues are in the retracted position (B) 5b. Then insert the lockbody into the extrusion. 5c. Fix with the 2x 10G screws. 1. Mill the jamb using the cutout details provided 2. Fit keeper in using the 2 x screws 3. Adjust the keeper position through the use of packers, and/or the adjustment screws. 4. Close the door and test the operation. Packer For horizontal adjustment Horizontal Adjustment Screws Fine tune horizontal adjustment Vertical Adjustment Screws Fixing slots allow for adjustment STEP 5: FITTING THE LOCKBODY DN1291 FLUSH KEEPER INSTALLATION: A A C B C B B C

Wetherill Park NSW 2164 Australia Ph: 1300 132 389 Fax: 1300 652 292 [email protected] www.doric.com.au DS2500 I FLUSH MOUNT MORTICE SLIDING DOOR LOCK INSTALLATION GUIDE 5 6. Screw the keeper into the fixing holes. 7. Adjust the keeper position through the use of packers, and/or the adjustment screws. 8. Remove the jig from the lockbody. 9. Close the door and test the operation. 4. Open the door and note the marked positions provided by the screws. 5. Pre drill the keeper fixing holes. 1. Insert the 2 x countersunk screw into the provided jig. 2. Insert the provided jig into the lockbody and over the anti-crash button. 3. Close the door with firm but not excessive force. DN1293 SURFACE KEEPER INSTALLATION: Jig with screws installed OR (If required) Packer For horizontal adjustment Horizontal Adjustment Screws Fine tune horizontal adjustment Vertical Adjustment Screws Fixing slots allow for adjustment A A C C B B B C