DOM 6655 Assembly Instruction Manual

Read all instructions before assembly and use. KEEP INSTRUCTIONS FOR FUTURE USE. ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly,keep out of reach of children until assembly is complete. THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. Consumer Care: www.dreamonme.com When contacting Dream On Me you will need to reference the above numbers .They can also be found on the label on the Crib End bottom rail. To register your product for important safety alerts and updates to your product please visit www.dreamonme.com and click on Product Registration. style #: 6655 Date: 5 IN 1 CRIB 1532 S WASHINGTON AVE PISCATAWAY TWP NJ 08854 OFFICE: 732-752-7220 CUSTOMER SERVICE: 732-366-1788

drapes may strangle a child. CAUTION: Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out.This crib has an sdjustable mattress support For the convenience of the parent when the baby is very small, the mattress support may be used in the highest position.Important: with the mattress support and mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches higher then the top surface of the mattress.If it is not, lower the mattress support and the mattress to the next h ighest position. . Fall Hazard: Stop using crib when child begins to climb out or reaches s height of 35in(89cm), whichever occurs first. The child should be placed in a youth or regular bed. . Check this product for damagde hardware, loose joints,loose bolts or other fasteners,missing parts, or sharp edges before and after assembly and frequently during use.Securdly tighten loose bolts and other fasteners. Do not use crib if any parts are missing,damagde or broken.Contact Dream On Me for replacement parts and instructional literature if needed.Do not substitute parts. ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A THICKNESS NOT To reduce the risk of SIDS,pediatricians recommend healthy infants be placedon their backs to sleep, unless otherwise advised by your physician. . Infants can suffocate on soft bedding.Never add a pillow or comforter.Never place additional padding under an infant. . . Strangulation Hazard:STRINGS CAN CAUSE STRANGULATION! Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys. Strangulation Hazard: To help prevent strangulation tighten all fasteners.A child can trap parts of the body or clothing on loose fasteners. Failure to follow these warnings and the assembly instructions could result inserious injury or death. DO NOT use this crib if you cannot exactly follow the accompanying instructions. WARNING: . . Follow warnings on all products in a crib. . If refinishing,use a non-toxic finish specified for children’s products. . Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation. . Infants can suffocate in gaps between crib sides and a mattress that is too small. . Ensure a safe environment for the child by checking regularly, before placing the child in the crib,that every component is properly and securely in place. . To avoid head injury, do not allow any child to play underneath the crib. . Never add an accessory such as a bassinet or changing table that extends over the sleeping area. . In Canada Only-Use a crib mattress that is no thicker than 15 cm and is of such a size that,when it is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or who is taller than 90 cm. EXCEEDING 6 IN.

During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the diagram of the item which is drawn actual size and design.Be sure to use the proper size and shape specified in the instructions. . INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT. Openings in and between bed parts can entrap head and neck of a small child. NEVER use bed with children younger than 15 months. ALWAYS follow assembly instructions. The maximum user weight is 50Ibs(22.7kg) WARNING: . To assemble this unit you may be required to place the unit on it’s side and face. It is strongly recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish. NOTES ON USE: Keep children and others safe by following these simple rules: . Do not allow any child to play on furniture. . Always monitor your child’s activity when in the nursery. NOTES ON CARE AND MAINTENANCE: . Do not scratch or chip the finish. STRANGULATION HAZARD NEVER place bed near windows where cords from blinds or drapes may strangle a NEVER suspend strings over a bed. NEVER place items with a string,cord,or ribbon,such as hood strings or pacifier around a child’s neck. These items may catch on bed parts. WARNING ENTRAPMENT HAZARD To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib at least 51 5/8 in (1310mm) in length, 27 1/4 (690mm) in width and 4 thickness. The mattress thickness must not exceed 6 in(150mm). CAUTION . Do not allow climbing on any piece of furniture. . Do not allow hanging from any piece of furniture. . Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp, cold basement. These extremes can cause a loss of structural integrity. . Inspect the product periodically, contact Dream On Me for replacement parts or questions. . To preserve the luster of the high quality finish on your product, it is recommended to place a doily or felt pad under any items you place on the finish. . Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish. . Do not use abrasive chemicals. . Do not spray cleaners directly onto furniture. . Lift slightly when moving on carpeting to prevent leg breakage. . Use of a vaporizer near furniture will cause wood to swell and finish to peel. child. cords, mattress in (100mm) in TODDLER BED

L'assemblage par un adulte est nécessaire. Les petites pièces peuvent présenter un danger d'étranglement avant l'assemblage. Ci-joint s'il vous plaît trouver les instructions simples, étape par étape pour vous aider à assembler rapidement vos produits. Avant de commencer, nous vous recommandons de suivre les étapes ci-dessous: 1.Lire attentivement les instructions, s'il vous plaît. 2.Identifier toutes les pièces et le matériel. 3.Vous aurez besoin des outils suivants: Tournevis tête phillips Tournevis à tête plate Marteau Ne pas utiliser les perceuses ou pilotes Pour protéger vos pièces lors de l'assemblage, placez-les sur une surface molle. Pour nettoyer la surface, utiliser seulement l'eau et un chiffon humide. Ne pas utiliser des nettoyants pour vitres ou des abrasifs de nettoyage car il va rayer la surface et pourrait endommager le revêtement protecteur. Le non-respect de ces avertissements et instructions peut entraîner des blessures graves ou la mort. Lisez toutes les instructions avant l'assembler du crèche, garder les instructions pour une utilisation future. À l'issue de l'assemblée, assurez-vous que toutes les vis, les boulons et les dispositifs de fixation ont été bien serrés. Un contrôle fréquent doit être fait. Ne jamais utiliser ce produit s'il y a des pièces desserrées ou manquantes, des joints lâches, des pièces cassées ou maille/tissu déchiré. Vérifiez avant le montage et périodiquement pendant l'utilisation. Contactez DREAM ON ME pour les pièces de rechange et des instructions, si nécessaire. Ne jamais substituer les parties, y compris le produit des rails latéraux, doivent être complètement érigé avant utilisation. Cesser d'utiliser le produit lorsque l'enfant est capable de sortir ou atteint la hauteur de 35 pouces (890mm). Ne placez jamais ce produit près de la fenêtre où les cordons de stores ou rideaux peuvent étrangler un enfant. Lorsque l'enfant est capable de tirer à la position debout, placez le matelas/base à la plus basse position de réglage et enlever les bordures de protection, les gros jouets et d'autres objets qui pourraient servir de marches pour grimper. Un enfant peut piéger les parties du corps ou les vêtements sur des fixations desserrées. Ne jamais utiliser de sac en plastique ATTENTION!

cette fin, ils peuvent provoquer la suffocation. ATTENTION: Tout matelas utilisé dans ce lit doit être au moins 27-1/4 pouces (690mm) par 51-5/8 pouces (1310mm), avec une épaisseur n'excédant pas 6 pouces (150 mm), les dimensions du matelas doivent être prises de la couture à la couture ou bord à bord dans le cas échéant. Ne jamais utiliser un matelas à eau avec ce produit. Les cordes peuvent étrangler! Ne jamais placer des objets avec une chaîne autour du cou de l'enfant, tels que les chaînes de capot ou de cordons de sucette. Ne jamais suspendre de ficelles sur le produit ou attacher des ficelles aux jouets. Les bébés peuvent être suffoqués dans les espaces entre un matelas trop petit ou trop épais au côtés et des produits, ne jamais ajouter un matelas, un oreiller, une couette ou un rembourrage sur un matelas mou. Pour réduire le risque de SMSN, les pédiatres recommandent que les enfants en bonne santé doivent être placés sur le dos pour dormir, sauf avis contraire de votre médecin. Si la finition, utilisez un fini non toxique indiqué pour les produits pour enfants. Les bébés peuvent suffoquer sur un matelas mou. Ne jamais ajouter un coussin ou une couverture. Ne placez jamais un rembourrage supplémentaire en vertu d'un nourrisson. Pour aider à prévenir l'étranglement, serrer toutes les fixations. . Un enfant peut piéger les parties du corps ou les vêtements sur des fixations desserrées. Respecter les avertissements sur tous les produits du berceau. Voir panneau tête et support du matelas du produit pour les avertissements. Remplacer dentition ferroviaire si endommagé, fissuré ou lâche. FABRIQUÉ EN CHINE

M. Mattress Support x1 B. Front Rail x1 H. Right Rear Leg x1 G. Left Rear Leg x1 E. Back Rail Bottom x1 A. Back Rail Top x1 PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT. F. Crib End x2 D. Right Front Leg x1 C. Left Front Leg x1 J. Left Crib End Top K. Right Crib End Top

Do not use power screwdriver Phillips Screwdriver (not supplied) PARTS: HARDWARE AND TOOLS M4 ALLEN WRENCH SUPPLIED a. 3-3/4'' Bolt x2 b. 3'' Bolt x12 d. 2-1/5'' Bolt x8 f. 3/4'' Bolt x4 g. Barrel nuts x20 h. Wood dowels x2 c. 2-3/5'' Bolt x2 e.1-3/4'' Bolt x4

with the M4 Allen Wrench. Parts and tools required to complete step. P 1 STE SECTION 1: CRIB ASSEMBLY M4 ALLEN WRENCH SUPPLIED F J e e F. Crib End x2 J. Left Crib End Top K. Right Crib End Top e e K F Attach (1) Crib End (Part F) to (1) Right Crib End Top (Part K) using (2) 1-3/4'' Bolts (Part e), Tighten with the M4 Allen Wrench. e. 1-3/4'' Bolt x4

Attach (1) Left Rear Leg (Part G), (1) Left Front Leg (Part C) to the assemblies from step 1 using (4) 2-1/5” Bolts (Part d) and (4) Barrel nuts (Part g). Tighten with the M4 Allen Wrench. Attach (1) Right Rear Leg (Part H), (1) Right Front Leg (Part D) to the assemblies from step 1 using (4) 2-1/5” Bolts (Part d) and (4) Barrel nuts (Part g). Tighten with the M4 Allen Wrench. d d d d d d d g g g g g g g g C D G H Parts and tools required to complete step. From Step 1 d. 2-1/5” Bolt x8 g. Barrel nuts x8 M4 ALLEN WRENCH SUPPLIED H. Right Rear Leg x1 G. Left Rear Leg x1 D. Right Front Leg x1 C. Left Front Leg x1

STEP 3 Parts and tools required to complete step. E. Back Rail Bottom x1 A. Back Rail Top x1 M4 ALLEN WRENCH SUPPLIED Attach (1) Back Rail Bottom (Part E) to (1) Back Rail Top (Part A) using (2) 3-3/4'' Bolts (Part a) and (2) 2-3/5''mm Bolts (Part c), Tighten with the M4 Allen Wrench. a a c c A E a. 3-3/4'' Bolt x2 c. 2-3/5'' Bolt x2

STEP 4 Parts and tools required to complete step. M4 ALLEN WRENCH SUPPLIED b. 3'' Bolt x6 g. Barrel nuts x6 From Step 3 From Step 2 g g g g g g b b b b b b Attach step 2 to the assemblies from step 3 using (6) 3'' Bolts (Part b) and (6) Barrel nuts (Part g). Tighten with the M4 Allen Wrench. From Step 2

The Warnings printed on the pouch attached to the mattress support must face up, the springs must face up. This crib has adjustment positions, use the highest only for new borns, move the mattress down as the child grows. WARNING: Fall Hazard: When child is able to pull to a standing position,set mattress to lowest position and remove bumper pads ,large toys and other objects that could serve as steps for climbing out. SECTION 1: CRIB ASSEMBLY STEP 5 Parts and tools required to complete step. M4 ALLEN WRENCH SUPPLIED f . 3/4" Bolt x4 M. Mattress Support x1 From Step 4 Attach the Mattress Support (Part M) in all corners using (1) 3/4" Bolt (Part f ) in each corner. Tighten with the M4 Allen Wrench. M f d f f f

STEP 6 Parts and tools required to complete step. M4 ALLEN WRENCH SUPPLIED b. 3" Bolt x6 g. Barrel nuts x6 h. Wood dowels x2 B. Front Rail x1 A. Back Rail Top x1 L. Stabilizer Bar x1 Attach (1) Front Rail (Part B), (1) Stabilizer Bar (Part L) to the assemblies from step 5 using (6) 3" Bolts (Part b), (6) Barrel nuts (Part g) and (2) Wood dowels (Part h). Tighten with the M4 Allen Wrench. L B b b b b b b b b g g h g g g g

all parts and tools separately, in a safe place. Assenmbly Instruction Booklet Parts and tools required to complete step. 7 P STE SECTION 1: CRIB ASSEMBLY Assenmbly Instruction Booklet WARNING:SEE PAGE 2 FOR INFORMATION Ai Bag Read all instructions before assembly and use. KEEP INSTRUCTIONS FOR FUTURE USE. ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly,keep out of reach of children until assembly is complete. THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. Consumer Care: www.dreamonme.com When contacting Dream On Me you will need to reference the above numbers .They can also be found on the label on the Crib End bottom rail. To register your product for important safety alerts and updates to your product please visit www.dreamonme.com and click on Product Registration. Dream On Me 5 in 1 Crib style #: Date: Read all instructions before assembly and use. KEEP INSTRUCTIONS FOR FUTURE USE. ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly,keep out of reach of children until assembly is complete. THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. Consumer Care: www.dreamonme.com When contacting Dream On Me you will need to reference the above numbers .They can also be found on the label on the Crib End bottom rail. To register your product for important safety alerts and updates to your product please visit www.dreamonme.com and click on Product Registration. Dream On Me 5 in 1 Crib style #: Date: Read all instructions before assembly and use. KEEP INSTRUCTIONS FOR FUTURE USE. ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly,keep out of reach of children until assembly is complete. THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. Consumer Care: www.dreamonme.com 125 Helen Street South Plainfield NJ 07080 When contacting Dream On Me you will need to reference the above numbers .They can also be found on the label on the Crib End bottom rail. To register your product for important safety alerts and updates to your product please visit www.dreamonme.com and click on Product Registration. Dream On Me 5 in 1 Crib style #: Date: 1532 S WASHINGTON AVE PISCATAWAY TWP NJ 08854 OFFICE: 732-752-7220 CUSTOMER SERVICE: 732-366-1788 1532 S WASHINGTON AVE PISCATAWAY TWP NJ 08854 OFFICE: 732-752-7220 CUSTOMER SERVICE: 732-366-1788

Parts and tools required to complete step. 1 P STE Section 2: Toddler Bed Conversion B b b b b g g

STEP 2 Stabilizer bar must be used when converted to a toddler bed. ！ WARNING: ！ SEE PAGE 3 FOR TODDLER BED WARNINGS The mattress support must be in the lowest positions. Store all hardware safely. Read all warnings on page 3. As shown, use as a day bed or love seat sofa. No Not use without stabilizer bar installed. A toddler bed guardrail is available for this crib. Please see your crib retailer, visit www.dreamonme.com or contact Consumer Care for more information. This crib uses Style #692 Guardrail.

1 P STE Section 3: Full Size Bed Conversion I M4 Allen Wrench Supplied You have the option to convert the crib to a Full Size Bed. Simply follow steps in reverse order to disassemble the crib. Then remove the Rear Legs from the left Crib End and Right Crib END with the M4 Allen Wrench as shown. Store all parts and hardware in a safe place.. Parts and tools required to complete step. d g d g g g d d d g g d d g

2 P STE Section 3: Full Size Bed Conversion I M4 Allen Wrench Supplied Parts and tools required to complete step. Converting kit is sold separately You have the option to convert crib to a full size bed II 1.Insert the split leg to the left&right side bar . 2.Connect the headboard Leg to the left side bar and the right side bar. 3.Connect the footboard Leg to the left&right side bar. 4.Connect the c to the left&right side bar. cross bar to the side bar. From Section 3 Step 1 Cross Bar (7PCS) Side Bar ( 4PCS) Split leg (2PCS)

Styles may vary . Modèle présenté à titre indicatif. Les styles peuvent varier. ou have the option to convert crib to a full size bed II 1:Use the back rail as the headboard of full size 3:Connect the assembled parts and headboard o hardware ) which are not included and sold sep 2:Connect the left foot platform and the right foot platform to the rail which are not included and sold separately. Converting kit is sold separately Le Kit de conversion est fourni séparément Vous avez la possibilité de convertir la crèche à un lit de taille complète II 1.Utilisez le rail de la tête arrière du grand lit. 2.Connectez la plate-forme de pied gauche et la plate- forme de pied droit sur les rails qui ne sont pas inclus 3.Connectez les pièces assemblées et tête de lit de lit de taille pour les kits (jambes, longuesrails et le matériel) qui ne sont pas inclus et vendus et vendu séparément. séparément. Parts and tools required to complete step. 1 P STE Section 3: Full Size Bed Conversion II Parts and tools required to complete step. From Section 3 Step 1 Left Foot Platform Post (1pc) Not Supplied Rail Post(6pcs) Not Supplied Not Supplied Right Foot Platform Post (1pc) Not Supplied

your product please visit www.dreamonme.com Please do not return this item to the store before contacting us about missing parts or with any questions. To report a problem, please log on to www.dreamonme.com and contact us by phone at 732-366-1788 In the event that you need to contact our customer service department please have the Style Number and MFG available. Use the space below to make note of those numbers. They can be found on the label on the Crib End bottom rail. STYLE No: 6655 COLOR FTY Lot No: Pack Date: Date of Purchase: (you should also keep your receipt)