Electroconcept M SPOT 120 Instruction Manual

PROFILE 120 SPOT LED Instruction manual Thank you for purchasing this product. Please carefully read this manual before using this moving head.

whatsoever, notably the operating loss, destruction of consumables (tape, disc, CD) or any other financial loss resulting from the use or the impossibility to use your equipment. In addition Electroconcept shall not be held responsible for damages due to an improper use of this product. Warranty : Electroconcept products have a 2 years manufacturer warranty. The equipment shall be returned prepaid (at the customer's own expense). Any freight collect will be refused. The equipment shall be returned in its original packaging. The equipment's restitution will be at our own expense. Are excluded from warranty: damages due to fault, negligence, lack of maintenance by the user (broken, burnt, heated, wet, sandy...etc devices), already installed devices of which the failure would originate from an improper installation or use by the customer. This manual is an integral part of this product, you will need to keep it during all of your product shelf- life. In the event of cession of your product to a third party, you must also give this manual to this third party. TABLE OF CONTENTS 1. Safety instructions 2. Technical specifications 3. Moving head starting up 1. Access to main functions 2. DMX wiring 4. DMX control channels and values 5. Troubleshooting 6. Cleaning 1. Safety instructions 2

valuable information for installation, operation and maintenance of this device  Warning Keep this manual for future consultations. If you resell your moving head to an other individual, make sure to also give him this manual. Unpack and carefully check that the moving head didn’t take any damages during the transport before using it. Before any connection, make sure that both the voltage and the frequency of your power source match your moving head specifications. Check your device as well as your equipment’s grounding. This device is only meant for indoor use ; protect it from heat and humidity (allowed ambient temperature from 10 to 40°C). The moving head must be set up in a ventilated area, at least 50cm away from any adjacent surface. Check that no ventilation hole is blocked. Unplug the moving head’s power source before any maintenance or handling operation. Only replace the fuse by a fuse of the same type. In order to avoid any fire hazard, check for any flammable source nearby. Use safety cables to secure the moving head. Hold the moving head only by its carrying handles to avoid degradation and risk of injury. Switch off the power and let the moving head cool down for about 15 minutes before transport, for the moving head’s surface may be hot still. In the event of a serious functioning problem, stop immediately to use the device. Do no ever try to repair the device by yourself. Repairs made by unqualified individuals may cause damages or malfunctions. Contact the nearest approved technical support center. Always use spare parts of the same type. Do not ever touch the led with your bare fingers after use to avoid serious injuries, for the led may be very hot still. Do not start the moving head without led to avoid degradation of the box.. Replace the box and the lenses if they are visually damaged (for example cracks or deep cuts during transport or handling). This is essential. Do not look straight at the light going out of led when the moving head is switched on. In order to prevent any risks of electrical shock you must not remove the cover. There is no useful part for the user inside. Refer the repair to qualified personnel. Installation 3

hook. Always make sure the moving head is firmly attached to avoid vibrations and sliding during the operation.. Always make sure the structure to which the moving head is attached is secured and able to bear 10 times the moving head’s weight. 2. Technical specifications. This device does not produce radio interference. This device meets European and French requirements. Compliance has been established, and statements and respective documents have been registered by the manufacturer. This device has been made for indoor decorative lighting effects. Power supply - AC 220-250V 50/60Hz Power - 180 W Lamp - LED 120W Shutter/Dimmer - Blackout, 0~100 variable strobe speed and soft transition Movement - Pan: 540/630° - Tilt: 270° Functions - color wheel 8 colors + white - gobos wheel 7 static gobos+ open - 3 facet rotating prism - linear focus Weight/Dimensions - 10,5 Kg / 330x240x360 mm Operating mode -DMX Control 15 or 19 channels./Stand-Alone with built-in microphone/Stand-Alone with automatic mode /Master/Slave Mode 3.Moving head starting up 3.1. Access to main functions Control panel: ”MENU“ “▼ ” “▲” ”ENTER” Press the “MENU” button to access to functions then « ▼ » or « ▲ » to browse through sub-menus, « ENTER » to confirm.“MENU” to go back. 2 Operating mode are available : DMX control or Stand-Alone mode. 4

Mode DMX Stand-Alone mode : Auto 1 /Auto 2 Auto 3 /Auto 4 XYeffect1/XYeffect2/XYeffect3/XYeffect4/ Random Sound mode adresse DMX DMX address selection from 001 to 512 Channel mode DMX 14 or 18 channels mode selection erse ON/OFF pan inversion Y reverse ON/OFF tilt inversion XY exchange ON/OFF XY encoder ON/OFF position sensor Screen mode ON backlight on OFF backlight shuts off after 30 seconds Version version of firmware /DMX channel /time since activation/number of total hours. Reset ON/OFF 3.2 DMX wiring This product uses 3-pin XRL connectors for the DMX512 connection: Pin 1 : Ground , Pin 2 : Data (-), Pin 3 : Data (+). Example : connection between different fixtures in Master/Slave mode: NB : in order to reduce signal errors, think of using a plug a the end of your DMX link. 4.DMX Control channels and values115 or 19 channels CHANNEL VALUE FUNCTION 1 PAN 0-255 Pan 2 PAN fin 0-255 Pan Fin 3 TILT 0-255 Tilt 5

0-255 Tilt Fin 5 Speed 0-255 Pan/Tilt speed 6 Shutter 0-3 4-251 255-255 Shutter closed STROBOSCOPE from slow to fast Shutter open 7 Dimmer 0-255 General dimmer 8 ,Colors 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-84 85-89 90-255 White White + Red Red Red + Orange Orange Orange + Green Green Green+ Light Blue Light Blue Light Blue + Purple Purple Purple + Yellow Yellow Yellow + Blue Blue Blue + Rose Rose Rose + White Clockwise rotation from slow to fast Counter-clockwise rotation from slow to fast 9、Gobos wheel 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-129 130-134 135-220 221-225 226-230 231-235 236-240 241-245 246-250 White Gobo1 Gobo2 Gobo3 Gobo4 Gobo5 Gobo6 Gobo7 Counter-clockwise rotation from slow to fast STOP Clockwise rotation from slow to fast Gobo1 Shake Gobo2 Shake Gobo3 Shake Gobo4 Shake Gobo5 Shake Gobo6 Shake 6

Clockwise Gobos rotation Gobos Shake rotation from slow to fast 11 Focus 0-255 Focus 0 – 100 % 12 Prism 0-127 128-255 No effect Prism effect 13 Prism rotation 0-63 64-127 128-191 192-255 Angle adjustment Counter-clockwise rotating prism Clockwise rotating prism Shake prism from slow to fast 14 Macro 0-5 6-10 51-100 101-150 151-255 Progressive Led shutdown. Immediate Led shutdown Program 1 Program 2 Program 3 15 Reset 0-25 26-76 77-127 128-255 No function Wheels reset PAN/TILT reset General reset 16 Color effects 0-4 5-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-89 85-89 90-94 95-114 115-134 135-154 155-174 White White + Red Red Red + Orange Orange Orange + Green Green Green+ Light Blue Light Blue Light Blue + Purple Purple Purple + Yellow Yellow Yellow + Blue Blue Blue + rose Rose Rose + White White Red Orange Green Light Blue 7

0-255 Color wheel rotation speed from fast to slow 18 Prism speed 0-255 Prism rotation speed from fast to slow 19 Gobos wheel speed 0-255 Gobos wheel rotation speed from fast to slow 5. Troubleshooting A. The moving head does not work, no lights nor fan : 1. Check the power cord and the main fuse. 2. Check that your electrical system is working. B. No response to DMX controller 1. A dot must flash on the device control screen. If it’s not the case, check if cables are properly connected and in good condition. 2. If the dot flashes, check your addressing as well as the polarity of your DMX wiring. 3. Try an other DMX controller 4. Avoid to lay your DMX cables alongside high-voltage lines to avoid interference. C.In Master/Slave Mode some devices don’t properly respond 1. Check cables and the connection diagram. 2. Check that devices are properly assigned in Master/Slave mode. 6. Cleaning Before any cleaning operation, unplug the moving head power cord in order to avoid any electrocution risk. Cleaning the optic must be done periodically in order to optimize the moving head’s brightness. The cleaning frequency depends on the operating environment. Smoke and dust may cause a large accumulation of dirt upon the moving head’s optics : - Clean it with a soft dry cloth. - Do not use liquid or detergent products. - Clean external lenses approximately every 20 days, with a soft dry cloth, without overly pressing on the lenses. La gare 69620 CHAMELET 8