Canon LEF7020028CA Instructions Manual

200mm f/2.8L IS II USM lens is a high- performance telephoto zoom lens equipped with an Image Stabilizer. • “IS” stands for Image Stabilizer. • “USM” stands for Ultrasonic Motor. Features 1. The Image Stabilizer gives the equivalent effect of a shutter speed four stops faster*. 2. With fluorite and UD lens elements, outstanding image delineation is obtained. 3. Ultrasonic motor (USM) for quick and quiet autofocusing. 4. Manual focusing is available after the subject comes into focus in autofocus mode (ONE SHOT AF). 5. A truly round aperture hole results in a nicer background blur. 6. The lens is compatible with Extender EF1.4X ll and EF2X ll. 7. Tight seal structure ensures excellent dust- proof and drip-proof performance. * Based on [1/focal length] second. Generally, it requires a shutter speed [1/focal length] second or faster to prevent camera shake. Thank you for purchasing a Canon product. Conventions used in this instruction Warning to prevent lens or camera malfunction or damage. Supplementary notes on using the lens and taking pictures.

a Safety Precautions • Do not look at the sun or a bright light source through the lens or camera. Doing so could result in loss of vision. Looking at the sun directly through the lens is especially hazardous. • Whether it is attached to the camera or not, do not leave the lens under the sun without the lens cap attached. This is to prevent the lens from concentrating the sun’s rays, which could cause a fire. Handling Cautions • If the lens is taken from a cold environment into a warm one, condensation may develop on the lens surface and internal parts. To prevent condensation in this case, first put the lens into an airtight plastic bag before taking it from a cold to warm environment. Then take out the lens after it has warmed gradually. Do the same when taking the lens from a warm environment into a cold one. • Do not leave the lens in excessive heat such as in a car in direct sunlight. High temperatures can cause the lens to malfunction. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003.

Filter mounting thread (→ 13) Focusing ring (→ 5) Focusing distance range selection switch (→ 5) Image stabilizer switch (→ 8) Image stabilizer mode selector switch (→ 8) Focus mode switch (→ 5) Distance scale (→ 11) Zoom ring (→ 6) Contacts (→ 4) Tripod mount (→ 12) Lens mount index (→ 4) Orientation lock knob (→ 12) Rubber ring (→ 4) For detailed information, reference page numbers are provided in parentheses (→**).

mounting and detaching the lens. • After detaching the lens, place the lens with the rear end up to prevent the lens surface and electrical contacts from getting scratched. • If the contacts get soiled, scratched, or have fingerprints on them, corrosion or faulty connections can result. The camera and lens may not operate properly. • If the contacts get soiled or have fingerprints on them, clean them with a soft cloth. • If you remove the lens, cover it with the dust cap. To attach it properly, align the lens mount index and the K index of the dust cap as shown in the diagram, and turn clockwise. To remove it, reverse the order. 1. Mounting and Detaching the Lens The lens mount has a rubber ring for enhanced water- and dust-resistance. The rubber ring may cause slight abrasions around the camera's lens mount, but this will not cause any problems. If the rubber ring becomes worn, it is replaceable by a Canon Service Center at cost.

1.2 m/3.9 ft. to infinity or 2.5 m/8.2 ft. to infinity. By setting the suitable focusing distance range, the actual autofocusing time can be shorter. 3. Switching the Focusing Distance Range 2. Setting the Focus Mode To shoot in autofocus (AF) mode, set the focus mode switch to AF. To use only manual focusing (MF), set the focus mode switch to MF, and focus by turning the focusing ring. The focusing ring always works, regardless of the focus mode. After autofocusing in ONE SHOT AF mode, focus manually by pressing the shutter button halfway and turning the focusing ring. (Full-time manual focus)

Be sure to finish zooming before focusing. Zooming after focusing can affect the focus.

position mark with the red dot on the front of the lens, then turn the hood as shown by the arrow until the lens' red dot is aligned with the hood's stop position mark. The ET-87 hood can keep unwanted light out of the lens, and also protects the front of the lens from rain, snow, and dust. Removing To remove the hood, hold down the button on the side and turn the hood in the direction of the arrow until the position mark on the hood aligns with the red dot. The hood can be reverse-mounted on the lens for storage. • Part of the picture may be blocked if the hood is not attached properly. • When attaching or detaching the hood, grasp the base of the hood to turn it. To prevent deformation, do not grasp the rim of the hood to turn it. Button

6. Image Stabilizer Settings Select the stabilizer mode. • MODE 1: Corrects vibrations in all directions. It is mainly effective for shooting still subjects. • MODE 2: It compensates for vertical camera shake during following shots in a horizontal direction, and compensates for horizontal camera shake during following shots in a vertical direction. When you press the shutter button halfway, the Image Stabilizer will start operating. • Make sure the image in the viewfinder is stable, then press the shutter button the rest of the way down to take the picture. Set the STABILIZER switch to . • If you are not going to use the image stabilizer function, set the switch to .

• In semi-darkened areas such as indoors or outdoors at night. • In locations where flash photography is prohibited, such as art museums and theater stages. • In situations where your footing is uncertain. • In situations where fast shutter settings cannot be used. • When panning subjects in motion. ●MODE 1 ●MODE 2 The image stabilizer in this lens is effective for hand-held shots under the following conditions.

• The Image Stabilizer cannot compensate for a blurred shot caused by a subject that moved. • Set the STABILIZER switch to when you are taking pictures using the Bulb setting (long exposures). If the STABILIZER switch is set to , the image stabilizer function may introduce errors. • The Image Stabilizer might not be fully effective in the following cases: • You shoot while riding on a bumpy road. • You move the camera dramatically for a panning shot in Mode 1. • You shoot using techniques other than following shots in Mode 2. • The Image Stabilizer consumes more power than normal shooting, so fewer shots can be taken if you use the function. • The image stabilizer operates for about two seconds even when your finger is off the shutter button. Do not remove the lens while the stabilizer is in operation. This will cause a malfunction. • With the EOS-1V/HS, 3, ELAN 7E/ELAN 7/30/33, ELAN 7NE/ELAN 7N/30V/33V, ELAN II/ELAN IIE/50/50E, REBEL 2000/300, IX, and D30, the Image Stabilizer will not work during self-timer operation. • Using a tripod also stabilizes the image. However, depending on the kind of tripod and shooting conditions, sometimes it may be better to turn off the Image Stabilizer function. • The stabilizer is equally effective for hand-held photography and photography with a monopod. • The Image Stabilizer function also operates when the lens is used with the EF12 II/EF25 II Extension Tube, and the EF1.4X II/EF2X II Extender. • Pictures may look distorted after being taken depending on the camera, but this doesn't affect shooting. • If you set the camera’s Custom Function to change the assigned button to operate the AF, the Image Stabilizer will operate when you press the newly assigned AF button.

9. Infrared Index Infinity compensation mark Distance index To compensate for shifting of the infinity focus point that results from changes in temperature. The infinity position at normal temperature is the point at which the vertical line of the L mark is aligned with the distance indicator on the distance scale. For accurate manual focusing of subjects at infinity, look through the viewfinder or look at the magnified image* on the LCD screen while rotating the focusing ring. * For cameras with Live View shooting capability. The infrared index corrects the focus setting when using monochrome infrared film. Focus on the subject manually, then adjust the distance setting by moving the focusing ring to the corresponding infrared index mark. • The infrared index position is based on a wavelength of 800 nm. • The compensation amount differs depending on the focal length. Use the indicated focal length as a guide when setting the compensation amount. • Be sure to observe the manufacturer’s instructions when using infrared film. • Use a red filter when you take the picture. Some EOS cameras cannot use infrared film. See the instructions for your EOS camera.

Adjusting the Revolving Mount You can loosen the orientation lock-knob on the tripod mount to allow it to rotate as needed to fit a particular camera model for switching between vertical and horizontal positions. Detaching First remove the lens from the camera and then remove the tripod mount from the lens as shown below. To attach the tripod mount, reverse the procedure. Loosen the orientation locking knob. Rotate the tripod mount and align the mounting indicator on the tripod mount with the one on the lens. Slide off the tripod collar away from the rear of the lens.

Circular Polarizing Filter (77mm). • To adjust the polarizing filter, first remove the lens hood. You can attach filters to the filter mounting thread on the front of the lens. 11. Filters (Sold separately) 13. Extension Tubes (Sold separately) Camera-to-Subject Magnification Distance (mm) Near Far Near Far EF12 ll 70mm 538 628 0.23× 0.17× 200mm 998 3404 0.28× 0.06× EF25 ll 70mm 400 406 0.42× 0.38× 200mm 862 1740 0.36× 0.14× You can attach Extension Tube EF12 II or EF25 II for magnified shots. The shooting distance and magnification are shown below. Manual focusing is recommended for accurate focusing. 12. Close-up Lenses (Sold separately) Attaching a 500D (77mm) Close-up Lens enables close-up photography. Magnification will be 0.14× – 0.60×. • Close-up Lens 250D cannot be attached because there is no size that fits the lens. • Manual focusing is recommended for accurate focusing.

• When an Extender is attached, the AF speed will become slower by design to retain proper AF control. • First attach the Extender to the lens, then attach the lens to the camera. Detach it from the camera in the reverse order. If you attach the lens to the camera first, misoperation may occur. • Only one Extender can be attached to the lens and camera. • If you use an Extender on the lens mounted on a EOS A2/A2E/5, set the exposure compensation to -1/2 stop for the EF1.4X ll or -1 stop for the EF2X ll. 14. Extenders (Sold separately) With Extender EF1.4X ll or EF2X ll attached, the lens specifications will change as follows: Item With EF1.4X ll Extender With EF2X ll Extender Focal length (mm) 98 – 280 140 – 400 Aperture f/4 – 45 f/5.6 – 64 Diagonal 25°20’ – 8°50’ 16°20’ – 6°10’ Angle of view Vertical 13°50’ – 4°55’ 9°10’ – 3°30’ Horizontal 20°50’ – 7°20’ 13°40’ – 5°10’ Maximum magnification (×) 0.30 0.44

70 – 200 mm, f/2.8 Lens Construction 23 elements in 19 groups Min. Aperture f/32 Angle of View Diagonal: 34° – 12° Vertical: 19°30’ – 7° Horizontal: 29° –10° Min. Focusing Distance 1.2 m / 3.9 ft. Max. Magnification & Field of view 0.21 × (at 200 mm), 308 × 463 – 115 × 171 mm /12.1 × 18.2 – 4.5 × 6.7 inch (at 1.2 m) Filter Diameter 77 mm Max. Diameter & Length 88.8 × 199 mm / 3.5 × 7.8 inch Weight 1490 g / 52.6 oz. Lens Hood ET-87 Lens Cap E-77U Case LZ1326 • The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm when including the lens cap and dust cap. • The size and weight listed are for the lens only, except as indicated. • Aperture settings are specified on the camera. • All data listed is measured according to Canon standards. • Product specifications and appearance are subject to change without notice.