EchoMaster Pro RVC-W8 Operation & User’s Manual

User Manual Must be used in conjunction with FCTP-GM1903 or FCTP-GM2003

RVC-W8 Wireless Camera & Receiver Kit Introduction Box Contents u Camera with Antenna (TX) u Camera Power Cable u 4Pin Din Extension Cable u Receiver (RX) Thank you for purchasing your EchoMaster Wireless Camera & Receiver. This EchoMaster camera with receiver is designed to improve safety during driving by providing high quality images of surrounding areas and obstacles in the vicinity of the vehicle. Please ensure you read and understand all aspects of this manual before fitting or using your EchoMaster camera. Choose a suitable mounting place dependant on the application. Ensure that there are no wiring harnesses or hoses/pipes located behind this panel before drilling. u Hole Saw u 2 x Red Male Spades u 2 x Red T-tap u 2 x 10mm screws RVC-W8 u 4 x Cable Ties u Double Sided Tape u User Manual u Warranty Card

RVC-W8 Wireless Camera & Receiver Kit Wiring Diagram & Pin-Out Camera wiring Red (Power) – Connect this wire to the positive parking lamp wire in the vehicle / trailer. Black (Ground) – Locate a suitable location to ground (negative) the Black wire in the wiring harness. You may connect this wire to a factory ground point in the vehicle, or attach a ring terminal to the black wire and screw into the body of the vehicle/trail- er. If you choose to screw into the body, clean the area of any paint or adhesives to allow for good metal-to-metal contact. Wire connections are illustrated in the diagram below. Be sure to test the suspected wires with a digital multimeter as trailer wiring is not universal.

RVC-W8 Wireless Camera & Receiver Kit Pairing the Camera The Camera & Receiver are automatically paired. There is no need to pair again unless you need to replace the receiver or camera. If this happens please follow the sequence below to pair the receiver and camera together. How to pair: Setup the video display to view the wireless camera. The “No Signal” screen should be displayed at this time. Within 30 seconds Press and Hold the receivers (RX) pair button for 3 seconds. Pairing will then start and a 30 second count down will be shown on the video display. Power up the camera by turning the vehicles parking lights on. Once pairing is complete the camera picture, along with a signal indicator, will appear on the video display and the LED on the receiver will be on constant.

RVC-W8 Wireless Camera & Receiver Kit Camera (with built-in TX) Image device HM1240 Lens specification 1/4inch 4G Horizontal angle 90° ± 5° Vertical angle 50° ± 5° Imaging resolution 1024 x 600 Pixel Minimum illumination 0 Lux / (infrared LED on) Transmission power 18 ± 2 dBm Working frequency 2.4GHz ~ 2.4835GHz Antenna gain 2.0 dBi @ 2400 ~ 2500MHz System IEEE 802.11 b/g/n Length of cable 36 in Current consumption <=350mA Power supply DC 12/24V Operating temperature -20°C to 65°C Specifications

RVC-W8 Wireless Camera & Receiver Kit Receiver (RX) Output signal AHD Output resolution 1024 x 600 Pixel Sensitivity -94dBm Working Frequency 2.4GHz ~ 2.4835GHz Antenna Gain 2.0 dBi @ 2400 ~ 2500GHz System IEEE 802.11 b/g/n Transmission range 100M Latency time 200ms Length of Cable 144in Operating Voltage DC 12/24V Working Current <= 250mA Operating temperature -20°C to 65°C Specifications (cont.)

RVC-W8 Wireless Camera & Receiver Kit Notes:

EchoMaster is a brand of AAMP Global. www.echomaster.com email - [email protected] - tel - 866-766-2267 (US) AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of use above and with all State and Federal laws. EchoMaster provides instructions and safety warnings with respect to this product and disclaims all liability for any use not in conformity with those instructions or other misuse of its product. If you do not agree, please discontinue use immediately and contact EchoMaster. This product is intended for off-road use and passenger use only. REV. 012221